*MNL-000126-00* - Ecosense Lighting

C AB LE S U S PE N D E D LU M I NAI R E SI N S TA L L ATI O N G U I D ESECTION 4.0:REMOTE POWEREDFIXTURES, OVERVIEWREMOTE DRIVER HOUSING[2][2]POWER FEEDSUSPENSION POINT[5]LOW VOLTAGE ELECTRICALCONNECTIONS[7][6][3]NON-FEED CABLE[4] CABLE GRIPPER[1]NON-POWER FEEDSUSPENSION POINTSLEEVE[4] CAP(COVERING CABLEGRIPPER)[8]NON-FEEDCC CAPPOWER FEEDCANOPYLUMINAIRECANOPY CAP SLEEVESECTION 4.1: REMOTE POWERED FIXTURES, PLAN THE INSTALLATIONBasic Installation Steps (detailed views & instructions in subsequent sections)NOTE: PSS Power Feed Cable comes preassembled onto luminiare body for single unit, remotepowered luminaires.1.2.3.Install remote driver housing and make mains electrical and control cable connections [fig 1]Install power feed and non-feed suspension point mountings to bldg. [fig 2]NOTE: FOR N1 and ND1 fixture types, skip step 4 below, and refer to “Section 3.4: Integral Fixtures, End Cap Removal &Ball End Cable Retainer.”1. These fixtures do not use the CC CAP referenced in step 4 below; they have removable end caps.4. Prepare fixture for hanging by unscrewing non feed CC CAP from top of fixture body. [fig 8]1. Feed the non feed aircraft cable [fig 7] through the bottom of the CC Cap until the cable stopper seats into theunderside of the CC CAP2. Next sleeve the cap sleeve [fig4] and non-feed canopy [fig 2] down the free end of the cable3. Now feed the free end of the NON-FEED aircraft cable into gripper at the ceiling suspension point [fig 2]; adjustthis cable to desired suspension length5. Now working on the other end of the fixture body, sleeve power feed canopy [fig 6] and the canopy cap sleeve [fig 3]onto PSS power feed cable (this is the cable that is preassembled to the fixture from the factory)1. Raise luminaire body1. For POWER FEED END of luminaire: insert cable into gripper and adjust cable to desired suspension length [fig 4]2. FOR NON-FEED END of luminaire: screw CC CAP into luminaire body.1. NOTE: FULLY SEAT CC CAP TO FIXTURE BODY IN THIS STEP, BY HAND TIGHTENING THE CC CAPUNTIL ACHEIVING SNUG FIT [fig 8]6. Make Low Voltage electrical connections at ceiling [fig 5]7. Slide the canopies and cap sleeves to the ceiling for all suspension pointsECOSENSE LIGHTING INC.837 NORTH SPRING STREETSUITE 103LOS ANGELES, CA 90012P 310 . 496 . 6255F 310 . 496 . 6256T 855 . 632 . 6736855 . 6 . ECOSENSPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.VISIT ECOSENSELIGHTING.COM FOR THE MOST CURRENT SPECIFICATIONS.FOR A LIST OF PATENTS VISIT ECOSENSELIGHTING.COM/IP-PORTFOLIO/ 2019 ECOSENSE LIGHTING INC. ALL RIGHTS RESERVED. ECOSENSE, THEECOSENSE LOGO, TRoV, TROV AND ECOSPEC ARE REGISTERED TRADEMARKSOF ECOSENSE LIGHTING INC.7/ 17RISE , SLIM COVE , FREEDOM TO CREATE , MACRO , FLIP-TO-FLAT ARETRADEMARKS OF ECOSENSE LIGHTING INC.20200107

C AB LE S U S PE N D E D LU M I NAI R E SI N S TA L L ATI O N G U I D ESECTION 4.2, REMOTE POWERED FIXTURES: POWER FEED CANOPY SUSPENSION POINT &REMOTE DRIVER HOUSING1. Install the remote driver and attach driver’sconduit onto the junction box.a. Max distance between remote driver &power feed is 100ft (at max run length,12ga wire recommended).a1. For suspended fixtures - subtractsuspension cable drop length from maxrun length.a2. (Example: a fixture with an 8ft cablesuspension length means max distancebetween remote driver and power feedMUD RINGREMOTE DRIVERbecomes 92ft).[A]2. Screw Mounting Bar [A] to JunctionBRACKET BARbox. For 4” square use round mud ring (as[B]pictured) or alternatively screw mounting barCABLE GRIPPERNOTE: Bracket Bar also canmount directly to 4in OctagonBox (by others)directly to 4” octagonal Junction box).3. Thread Cable Gripper Sleeve [E] & Canopy[C] onto aircraft cable.MOUNTING SCREWS[D]CANOPY4. Screw cable gripper [B] into mounting bar5. Push PSS cable [C] through the cablegripper.6. Adjust cable to desired suspension length[E] CABLE GRIPPER SLEEVEPOWERED SUSPENSION SYSTEM(PSS) CABLE7. Strip the PSS cable jacket to expose the wires.[C]8. Connect the wires from remote driver tothe PSS cable.9. Slide Canopy [D] & Cap Sleeve [E] up theaircraft cable to complete.LUMINAIRE1. Remove the 2 screws on each end cap using a 1/4” hex head screwdriver or a flat head screw driver2. Remove the lid (Note: grounding wire is attached to the lid)ECOSENSE LIGHTING INC.837 NORTH SPRING STREETSUITE 103LOS ANGELES, CA 90012P 310 . 496 . 6255F 310 . 496 . 6256T 855 . 632 . 6736855 . 6 . ECOSENSPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.VISIT ECOSENSELIGHTING.COM FOR THE MOST CURRENT SPECIFICATIONS.FOR A LIST OF PATENTS VISIT ECOSENSELIGHTING.COM/IP-PORTFOLIO/ 2019 ECOSENSE LIGHTING INC. ALL RIGHTS RESERVED. ECOSENSE, THEECOSENSE LOGO, TRoV, TROV AND ECOSPEC ARE REGISTERED TRADEMARKSOF ECOSENSE LIGHTING INC.8/ 17RISE , SLIM COVE , FREEDOM TO CREATE , MACRO , FLIP-TO-FLAT ARETRADEMARKS OF ECOSENSE LIGHTING INC.20200107

C AB LE S U S PE N D E D LU M I NAI R E SI N S TA L L ATI O N G U I D ENon-power unit only:SECTION 4.3, REMOTE POWERED FIXTURES: NON-FEED SUSPENSION POINTSAdjust cable length to desired height of fixture.Option #44 (4” Canopy)1.Screw Mounting Bar [A] to Junction box.For 4” square box, use round mud ring[by others] (as pictured) or alternativelyscrew mounting bar directly to 4”octagonal junction box.2.[A]NOTE: For N1 and ND1 fixture types, referto section 3.4: Integral Fixtures, End CapRemoval & Ball End Cable Retainer.[B]1. These fixtures do not use the CCCAP; they have removable end caps.3.Prepare fixture for hanging byunscrewing non feed CC CAP from top of[C] CANOPYfixture body. [fig F]1. Feed the non feed aircraft cablethrough the bottom of the CC[F]CAP until the cable stopper seats intothe underside of the CC CAP.2. Next, slide the cap sleeve [D] and[D]CABLE GRIPPER SLEEVEnon-feed canopy [C] down the freeend of the cable.4.Screw cable gripper [B] into mounting bar.5.Push aircraft cable through the cable[E] AIRCRAFT CABLEgripper.3 MNL-000127-00 CS-CR, CSD-CR, CSI-CR6.Adjust cable to desired suspension length.7.Slide canopy [C] & cap sleeve [D] up theaircraft cable to complete.Option #40 & #41 (Canopy Free and Mini Canopy)THREADED STUD(BY OTHERS)MINI CANOPY(41 ONLY)1.Fasten a 1/4-20 stud (by others) securely to the ceiling2.Thread cable gripper onto the 1/4-20 studFor option #41, add the mini canopy between theGRIPPERAIRCRAFT CABLEceiling and the gripper before threading to the stud3.Push aircraft cable through the cable gripper4.Adjust cable to desired suspension lengthLUMINAIREECOSENSE LIGHTING INC.837 NORTH SPRING STREETSUITE 103LOS ANGELES, CA 90012P 310 . 496 . 6255F 310 . 496 . 6256T 855 . 632 . 6736855 . 6 . ECOSENSPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.VISIT ECOSENSELIGHTING.COM FOR THE MOST CURRENT SPECIFICATIONS.FOR A LIST OF PATENTS VISIT ECOSENSELIGHTING.COM/IP-PORTFOLIO/ 2019 ECOSENSE LIGHTING INC. ALL RIGHTS RESERVED. ECOSENSE, THEECOSENSE LOGO, TRoV, TROV AND ECOSPEC ARE REGISTERED TRADEMARKSOF ECOSENSE LIGHTING INC.9/ 17RISE , SLIM COVE , FREEDOM TO CREATE , MACRO , FLIP-TO-FLAT ARETRADEMARKS OF ECOSENSE LIGHTING INC.20200107

WIRING DIAGRAMC AB LE S U S PE N D E D LU M I NAI R E SIWD-CS-REM-010VN S TA L L ATI O N G U I D ESECTION 4.4, REMOTE POWERED FIXTURES: WIRING DIAGRAMStandard WiringREDREDBLACKBLUERemote Driver HousingWHITEBLACKCommonSwitched HotGREENGNDPURPLEWHITE0-10 VOLT DIMMING ( )0-10 VOLT DIMMING (-)Coaxial Power Cable From FixtureWIRING DIAGRAMWD-CS-REM-010V-DUALDual Circuit WiringCable Suspended Remote Driver 0-10vREDCommonSwitched HotGND0-10 VOLT DIMMING ( )0-10 VOLT DIMMING (-)REDBLACKBLUERemote Driver HousingREDREDBLUE0-10 VOLT DIMMING (-)0-10 VOLT DIMMING ( )GNDSwitched HotCommonBLACKCoaxial Power Cable From FixtureCoaxial Power Cable From FixtureCable Suspended Remote Driver 0-10v DualECOSENSE LIGHTING INC.837 NORTH SPRING STREETSUITE 103LOS ANGELES, CA 90012P 310 . 496 . 6255F 310 . 496 . 6256T 855 . 632 . 6736855 . 6 . ECOSENSPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.VISIT ECOSENSELIGHTING.COM FOR THE MOST CURRENT SPECIFICATIONS.FOR A LIST OF PATENTS VISIT ECOSENSELIGHTING.COM/IP-PORTFOLIO/ 2019 ECOSENSE LIGHTING INC. ALL RIGHTS RESERVED. ECOSENSE, THEECOSENSE LOGO, TRoV, TROV AND ECOSPEC ARE REGISTERED TRADEMARKSOF ECOSENSE LIGHTING INC.1 0/ 17RISE , SLIM COVE , FREEDOM TO CREATE , MACRO , FLIP-TO-FLAT ARETRADEMARKS OF ECOSENSE LIGHTING INC.20200107

C AB LE S U S PE N D E D LU M I NAI R E SI N S TA L L ATI O N G U I D ESECTION 4.5REMOTE POWERED FIXTURES: ‘ZERO CANOPY’ SERIES, #2ACT- POWER FEED, & NON-FEEDCANOPY SUSPENSION POINT1.Screw ‘Zero’ series mounting plate [A] to 4inch square junction box.2.Adjust threaded cylinder to match ceiling thickness [B]3.Thread magnetized cover plate [C] onto aircraft cable4.Push PSS or standard suspension cable through the cable gripper [D]5.Adjust cable to desired suspension length6.If this is a power feed point1. Strip the PSS cable jacket to expose the wires.2. Connect the wires from remote driver to the PSS cable.7.Slide magnetized cover plate [C] up to the ceiling where it’s retained magnetically[D][B][A]LOW-VOLTAGECABLE[C]SECTION 4.5A‘ZERO CANOPY’ SERIES, #2MIC - POWER FEED & NON-FEED CANOPY SUSPENSION POINT5.If this is a power feed pointa. Strip the PSS cable jacketto expose the wires.b. Connect the wires fromremote driver to the PSS cable.6.[A]Slide magnetized cover plate[C] up to the ceiling where it’sMUD IN PLATEretained magnetically.1.2.3.Screw MUD IN plate [A] to 4inch7.NOTE: To remove cover, push onsquare junction box.one end of cover. This will TILTThread magnetized cover platethe cover on the center axis and[C] onto aircraft cable.allow you to grab it.Push PSS or standard suspensioncable through the cable gripper[D].4.Adjust cable to desiredsuspension length.ECOSENSE LIGHTING INC.837 NORTH SPRING STREETSUITE 103LOS ANGELES, CA 90012P 310 . 496 . 6255F 310 . 496 . 6256T 855 . 632 . 6736855 . 6 . ECOSENSPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.VISIT ECOSENSELIGHTING.COM FOR THE MOST CURRENT SPECIFICATIONS.FOR A LIST OF PATENTS VISIT ECOSENSELIGHTING.COM/IP-PORTFOLIO/ 2019 ECOSENSE LIGHTING INC. ALL RIGHTS RESERVED. ECOSENSE, THEECOSENSE LOGO, TRoV, TROV AND ECOSPEC ARE REGISTERED TRADEMARKSOF ECOSENSE LIGHTING INC.11/ 17RISE , SLIM COVE , FREEDOM TO CREATE , MACRO , FLIP-TO-FLAT ARETRADEMARKS OF ECOSENSE LIGHTING INC.20200107

ed on previously installed fixture 1. Tighten two set screws from top of fixture throughclearance holes.C AB LE S U S PE N D E D LU M I NAI R E SI N S TA L L ATI O N G U I D ESECTION 5.0JOINING CONTINUOUS RUNS – STYLE #CR: SINGLE SEAM NON-ROTATIONAL1.Make electrical connections between fixtures.2.Slide fixture 2 onto alignment pins [A] locatedSET SCREWS[B]CABLEon previously installed fixture 1.3.Tighten two set screws [B] from top of fixtureALIGNMENT PINSthrough clearance holes.3a. Allen key size: 1/16”, 5/64”[A]FIXTURE 2[C]CONTINUIOUS RUN BRACKETFIXTURE 1SECTION 5.1JOINING CONTINUOUS RUNS – STYLE #CSR: ROTATIONAL1.Connect fixture 2 to fixture 1 by inserting the piston into the knuckle.2.Rotate fixture to desired position3.Tighten set screw [A] in knuckle.3a. Allen key size: 1/16”, 5/64”INTEGRAL POWERED FIXTURE7 MNL-000127-00CS-CR, CABLECSD-CR, CSI-CRAIRCRAFTFIXTURE 1SET SCREWS[A]KNUCKLEREMOTE POWERED FIXTUREFIXTURE 2PISTONECOSENSE LIGHTING INC.P 310 . 496 . 6255837 NORTH SPRING STREETF 310 . 496 . 6256DETAIL BSUITE 103SCALE 1 : 1 T 855 . 632 . 6736855 . 6 . ECOSENLOS ANGELES, CA 90012SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.VISIT ECOSENSELIGHTING.COM FOR THE MOST CURRENT SPECIFICATIONS.FOR A LIST OF PATENTS VISIT ECOSENSELIGHTING.COM/IP-PORTFOLIO/ 2019 ECOSENSE LIGHTING INC. ALL RIGHTS RESERVED. ECOSENSE, THEECOSENSE LOGO, TRoV, TROV AND ECOSPEC ARE REGISTERED TRADEMARKSOF ECOSENSE LIGHTING INC.12 / 17RISE , SLIM COVE , FREEDOM TO CREATE , MACRO , FLIP-TO-FLAT ARETRADEMARKS OF ECOSENSE LIGHTING INC.20200107

C AB LE S U S PE N D E D LU M I NAI R E SI N S TA L L ATI O N G U I D EREMOTE POWERED FIXTUREPSS CABLE[A]FIXTURE 1FIXTURE 2SET SCREWSPISTONKNUCKLESECTION 6.0EMB OPTION1.2.DETAIL ASCALE 1 : 1Remote powered fixture canopy pictured.Integral powered fixtures (not pictured)have test switch on fixture body.AECOSENSE LIGHTING INC.837 NORTH SPRING STREETSUITE 103LOS ANGELES, CA 90012P 310 . 496 . 6255F 310 . 496 . 6256T 855 . 632 . 6736855 . 6 . ECOSENSPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.VISIT ECOSENSELIGHTING.COM FOR THE MOST CURRENT SPECIFICATIONS.FOR A LIST OF PATENTS VISIT ECOSENSELIGHTING.COM/IP-PORTFOLIO/ 2019 ECOSENSE LIGHTING INC. ALL RIGHTS RESERVED. ECOSENSE, THEECOSENSE LOGO, TRoV, TROV AND ECOSPEC ARE REGISTERED TRADEMARKSOF ECOSENSE LIGHTING INC.13/ 17RISE , SLIM COVE , FREEDOM TO CREATE , MACRO , FLIP-TO-FLAT ARETRADEMARKS OF ECOSENSE LIGHTING INC.20200107

C AB LE S U S PE N D E D LU M I NAI R E SI N S TA L L ATI O N G U I D EINTEGRAL POWERED FIXTURE EMB WIRINGWHITE w/BLACKBLACK HITEN/AEM Constant PowerCommonSwitched HotGround0-10v Dimming ( )0-10v Dimming (-)2 Port Connector - EMB power(DO NOT DISCONNECT)POWER CORD FROM FIXTUREREMOTE POWERED FIXTURE EMB WIRINGREDREDBLACKBLUEREDBLACK2 Port WagoCommonSwitched HotGroundEM Constant PowerREDBLUERemote Driver Housing0-10v Dimming ( )0-10v Dimming (-)Low Voltage Power Cable From FixtureECOSENSE LIGHTING INC.837 NORTH SPRING STREETSUITE 103LOS ANGELES, CA 90012P 310 . 496 . 6255F 310 . 496 . 6256T 855 . 632 . 6736855 . 6 . ECOSENSPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.VISIT ECOSENSELIGHTING.COM FOR THE MOST CURRENT SPECIFICATIONS.FOR A LIST OF PATENTS VISIT ECOSENSELIGHTING.COM/IP-PORTFOLIO/ 2019 ECOSENSE LIGHTING INC. ALL RIGHTS RESERVED. ECOSENSE, THEECOSENSE LOGO, TRoV, TROV AND ECOSPEC ARE REGISTERED TRADEMARKSOF ECOSENSE LIGHTING INC.14/ 17RISE , SLIM COVE , FREEDOM TO CREATE , MACRO , FLIP-TO-FLAT ARETRADEMARKS OF ECOSENSE LIGHTING INC.20200107

C AB LE S U S PE N D E D LU M I NAI R E SI N S TA L L ATI O N G U I D EWIRING DIAGRAMSECTION 6.1WD-CS-INT-010V-EMWEMW OPTIONWHITE w/BLACKBLACK HITECommon - EM CircuitSwitched Hot - EM CircuitCommon - Main CircuitSwitched Hot - Main CircuitGND0-10 VOLT DIMMING ( )0-10 VOLT DIMMING (-)0-10 VOLT DIMMING ( )0-10 VOLT DIMMING (-)MainCircuitEMCircuitPOWER CORD FROM FIXTURECable Suspended Integral Driver 0-10v EMWECOSENSE LIGHTING INC.837 NORTH SPRING STREETSUITE 103LOS ANGELES, CA 90012P 310 . 496 . 6255F 310 . 496 . 6256T 855 . 632 . 6736855 . 6 . ECOSENSPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.VISIT ECOSENSELIGHTING.COM FOR THE MOST CURRENT SPECIFICATIONS.FOR A LIST OF PATENTS VISIT ECOSENSELIGHTING.COM/IP-PORTFOLIO/ 2019 ECOSENSE LIGHTING INC. ALL RIGHTS RESERVED. ECOSENSE, THEECOSENSE LOGO, TRoV, TROV AND ECOSPEC ARE REGISTERED TRADEMARKSOF ECOSENSE LIGHTING INC.1 5/ 17RISE , SLIM COVE , FREEDOM TO CREATE , MACRO , FLIP-TO-FLAT ARETRADEMARKS OF ECOSENSE LIGHTING INC.20200107

C AB LE S U S PE N D E D LU M I NAI R E SI N S TA L L ATI O N G U I D EINSTALLATION CONSIDERATIONSCaution, risk of electric shock.Remarques Concernant L’installationAttention : risque de choc électrique.MIN 90C SUPPLY CONDUCTORSLES FILS D’ALIMENTATION 90C MINCable Suspended Remote Power Unit with Cable Suspended Luminaire / Unité d’alimentation à distance suspendue avec luminaire suspendu par un câbleELECTRICAL RATINGS / CARACTÉRISTIQUES ÉLECTRIQUESOPERATING VOLTAGE / Tension de Fonctionnement120-277VAC, 50/60 Hz, MAX 0.22-0.10A, MAX 26W NOMINAL PER FOOT OF LUMINAIRE HOUSING LENGTH / Puissance nominale par pied de la longuer du boîtier du luminaire347V, 50/60Hz, MAX 26W NOMINAL PER FOOT OF LUMINAIRE HOUSING LENGTH / Puissance nominale par pied de la longuer du boîtier du luminaire347-480V, 50/60Hz, MAX 0.07 - 0.05A, MAX 36W NOMINAL PER FOOT OF LUMINAIRE HOUSING LENGTH / Puissance nominale par pied de la longuer du boîtier du luminaireWhen shipped separately, surface mounted luminaire rated max nominal 600 mA/ ft total or max nominal 24W/ft constant current or max nominal 24 Vdc constant voltageas applicable based on LED array type provided. / Lorsqu’il est expédié séparément, le luminaire monté en surface a une valeur nominale maximale de 600 mA/pied au totalou un courant constant de fréquence nominale maximale de 24 W/pied ou une tension constante nominale maximale de 24 Vcc, selon le cas et la LED et en fonction du typede tableau fourni.Cable Suspended Integral Driver Cable Suspended Luminaire/ Boîtier intégral suspendu par un câble avec luminaire suspendu par un câbleOPERATING VOLTAGE / Tension de Fonctionnement120-277V, 50/60Hz, MAX 0.22-1.10A NOMINAL PER FOOT OF LUMINAIRE / Puissance nominale par pied de la longuer du boîtier du luminaire77 F (25 C)OPERATING TEMPERATURE / Température de Fonctionnement:Refer to electrical rating marked on the luminaire. / Reportez-vous aux caractéristiques électriques indiquées sur le luminaire. Read and understand the installation instructions before attempting to install or use the fixture.Lire et comprendre les instructions d’installation avant de tenter d’installer ou d’utiliser l’appareil. Only use fixtures with voltage for which it is rated. Do not exceed the specified voltage and current input.N’utiliser que des appareils avec une tension pour laquelle il est classé. Ne pas dépasser la tension indiquée et la puissance absorbée. Do not use fixture if the housing, lens, or power cable are damaged.Ne pas utiliser cet appareil si le boîtier, l’objectif ou câble d’alimentation sont endommagés Ensure that main power supply is off before installing or wiring a fixture.Assurez-vous que l’alimentation principale est coupée avant l’installation ou le câblage d’un appareil. Hazardous live parts shall not be accessible after installation, and it is the installer’s responsibility to ensure that the installation/connections are in compliance with nationaland local electrical codes and regulations.Les parties actives dangereuses ne doit pas être accessible après installation, et c’est la responsabilité de l’installateur de s’assurer que l’installation / connexions sont conformesaux codes nationaux et locaux électriques et les règlements The wire connection method shall be determined by local electrical codes and regulations, typically using either wire nuts or screw terminal blocks.La méthode de connexion de fil doit être déterminé par les codes électriques locaux et des règlements, typiquement en utilisant soit les serre-fils ou borniers à vis. Possibly hazardous optical radiation emitted from this product.Peut-être dangereux rayonnement optique émis par ce produ

*mnl-000126-00* installation guide 1/17 20200107 p 310.496.6255 f 310.496.6256 t ecosense855.632.6736 855.6.ecosen ecosense lighting inc. 837 north spring street suite 103 los angeles, ca 0012 rise specifications subject to change without notice. visit e