Sivoia QED Wireless Roller 64 For HomeWorks
Sivoia QED Wireless Roller 64 for HomeWorks InstallationInstructions
Sivoia QEDTM Wireless Roller 64 for HomeWorksInstallation InstructionsTools Required:Tape MeasureWire Cutter/StripperPliers#2 Phillips Screwdriver1/4” Hex-Head DriverLevelPower DrillNotes:1)2)For Wireless Roller 64 programming refer to the HomeWorks Illumination Online Help.The Electronic Drive Unit (EDU) will need to be powered to complete installation.Wireless Shades will not function until they are addressed and programmed using theHomeWorks Illumination Software.Box Contents:Sivoia QED Wireless Roller 64(2) Bracket Leveling Spacer (2) Cable Tie AnchorStandard Mounting Bracketswith Retaining Screws(1) 3 Pin Terminal Block(5) Mounting Screws(#8x1-3/4" (#8x44mm) Hex Head Screws)(2) 4” (102mm) Cable Ties(Actual Size)(1) Programming StylusSIVOIA QED Wireless Roller 64 Installation Instructions 1TM(1) Screwdriver(2) AntennaMounting Clips
Sivoia QEDTM Wireless Roller 64 for HomeWorksInstallation Instructions (continued)Warning: Incorrect installation can lead to severe injury, follow all installation instructions.Notes: The Sivoia QED Wireless Roller 64 must be used only with window treatments approved by Lutron. There must be a clearance of at least 1.3 feet (0.4 meters) between the fully lowered systemand any permanent object. Installation shall be executed by a qualified electrician according to national wiring rules. Before shade installation, remove any unnecessary cords and disable any equipment notneeded for powered operation. The Sivoia QED Wireless Roller 64 has a maximum rated operatingtime of 8 min. out of 20. Codes: Install in accordance with all local and national electrical codes. Environment: Ambient operating temperature: 0-40 C, 32-104 F, 0-90% humidity, non-condensing.Indoor use only.SIVOIA QED Wireless Roller 64 Installation Instructions 2TM
Sivoia QEDTM Wireless Roller 64 for HomeWorksInstallation Instructions (continued) RF Device Placement: Wireless shades must be located within 30 feet (9m) of an RF SignalRepeater or an RF Processor. The distance between repeater and processor must be less than60 feet (18m).Wireless shades will not function until they are addressed and programmed. See the HomeWorksIllumination Software Online Help.Wireless shades are programmed with a personal computer using the HomeWorksIllumination Software.30 feet (9m)30 feet (9m)SIVOIA QED Wireless Roller 64 Installation Instructions 3TM
11Confirm System DimensionsPackage Label1.1Compare system dimensions onthe package label with the windowdimensions to verify appropriatewindow/shade combination.System WidthSystem WidthSystem Height(Bracket to Bracket Width)SIVOIA QED Wireless Roller 64 Installation Instructions 4TMSystem Height
2Position the Mounting Brackets2.1Mark the location of the mounting brackets so that they are centered over the window.Note: Bracket to Bracket distance Fabric Width 1.5” (38 mm) System Width.Note: For ceiling and jamb mount, allow clearance to prevent fabric from rubbing against trim, window,top treatment, etc.Note: Wall mount may require blocks (not provided) to clear trim.(System Width)AAASIVOIA QED Wireless Roller 64 Installation Instructions 5TM
3Install the Mounting Brackets3.1Install the first mounting bracket.3.2Install the second mounting bracket.Note: Put a screw in the center of each slot. Use slots as needed toensure brackets are level and plumb as positioned.SIVOIA QED Wireless Roller 64 Installation Instructions 6TM
4Pre-drill for Cable RunDANGER - Locate and lock breaker to the shade power supply in the OFF positionor unplug the power plug-in transformer before doing any wiring.4.1Wall MountChoose one of the options below to drill for cable access.Note: Cable should exit from wall, ceiling, or jamb on EDU side of system.Note: Leave 12-18” (30-45 cm) of cable exposed.Wall Mount with wires through:A) Wall: 1” in from end of system and .5” from top of bracketB) Ceiling: .5” in from end of system and .5” from mounting wallC) Jamb: 1” from top of bracket and .5” from mounting wallWall MountABSIVOIA QED Wireless Roller 64 Installation Instructions 7TMC
44.2Pre-drill for Cable Run: (continued)Ceiling MountCeiling Mount with wires through:A) Wall: 1” in from end of system and .5” from ceilingB) Ceiling: 1” in from end of system and .5” from back of bracketC) Jamb: 1” from back of bracket and .5” from ceilingCeiling MountABSIVOIA QED Wireless Roller 64 Installation Instructions 8TMC
44.3Pre-drill for Cable Run: (continued)Jamb MountJamb Mount with wires through:A) Wall: .5” from ceiling and .5” from outside of jambB) Ceiling: .5” from wall and .5” from outside of jambC) Jamb: .5” from ceiling and .5” from wallJamb MountABSIVOIA QED Wireless Roller 64 Installation Instructions 9TMC
5Wire 3-Pin Terminal Block5.1Strip 2” of jacketoff cable run fromthe wall.5.2Wire 3-Pin terminal block (provided) to cable using the included screwdriver.EGND (Pin 3)24 VAC (Pin 2)24 VAC (Pin 1)SIVOIA QED Wireless Roller 64 Installation Instructions 10TMTo EDUConnector
6Orient the Buttons and Wiring6.1For the following bracket and button orientations, route the wires as shown.Note: The buttons should be accessible when the shade is installedNote: The wires may go in either or both of the indicated slotsntiorecirDheEitSIVOIA QED Wireless Roller 64 Installation Instructions DheEit
7Mount the Shade7.1Install the idler side of the shade onto its bracket.7.2Depress the spring loaded idler by pressing the shade towards the idler, and install the EDUside of the shade onto its bracket.SIVOIA QED Wireless Roller 64 Installation Instructions 12TM
8Adjust the Shade8.1Ensure that the shade is level and centered.8.2Adjust shade by removing the necessary screws and moving the brackets as needed, orinstalling bracket leveling spacers.Note: You may have to remove the shade to access the bracket screws.8.3Reinstall and tighten the screws.SIVOIA QED Wireless Roller 64 Installation Instructions 13TM
9Secure the Antenna9.1For optimal performance secure the antenna in 1 of 3 configurations shown below usingthe antenna clips provided.WARNING: - The antenna is covered with a clean Plastic sleeve to protect it. Do notcut the antenna or remove the plastic sleeve. Do not modify the antenna.Antenna mounted parrallel with shadeuse these configurations. When Pocketor Fascia is not used.Antenna mounted straight down.Antenna clipped to bottom of Pocket or Fascia - This configuration provides optimal performance withmetal Fascia.Note: Lutron has tested this product with the antenna mounted in the configurations aboveand found that these provide optimal performance.SIVOIA QED Wireless Roller 64 Installation Instructions 14TM
10Connect Terminal Blocks10.1Plug 7-pin terminal block on cable into EDU terminal block attached to shade bracket(a cable tie can be used to secure the terminal blocks together).10.2Dress wires to ensure fabric does not rub while the shade is moving.WARNING: Do not cut wires coming out of shade. Doing so will damage the antenna.10.3Copy the serial number located on every shade’s harness and shade location on page 21 of thismanual. This will ease addressing and programming later on the installation.SIVOIA QED Wireless Roller 64 Installation Instructions 15TM
11Secure and Check the Shade11.1Tighten retaining screws in each bracket to secure the shade.SIVOIA QED Wireless Roller 64 Installation Instructions 16TM
11.2 Secure and Check the Shade (continued)Reconnect power to the shade power supply.Use the programming stylus to run the shade up and down using the adjustmentbuttons (), re-level if needed.Observe: Pay careful attention to the shade roll up to ensure that it does not telescopeextremely to one side or the other.Tip: Slight telescoping is normal. However, if the shade is telescoping severely to oneside and it is level, press the “Close Limit Button” ( ), and lower the shade all the waydown using the adjustment buttons (). Place a piece of tape on the side of the tubethat the fabric is telescoping away from when finished press the “Close Limit Button” ( )once. This technique is referred to as “SHIMMING”. The shade will always track towardsthe side that the tape (shim) is placed on.SIVOIA QED Wireless Roller 64 Installation Instructions 17TM
12Setting Limits from the EDUSetting the Open Limit from the EDUNote: Setting the Open Limit lower than the Close Limit will cause the shade to move downwhen raise is pressed and up when lower is pressed.12.1Tap the “Open Limit Button”( ), the green LED on theroller shade EDU will turn onsteady, indicating that the EDUis in “Set Open Limit Mode.”12.2Adjust the position of theEDU to the desired OpenLimit using the adjustmentbuttons ( ).12.3Press and hold the “OpenLimit Button” ( ) for 5seconds. The green LED onthe roller shade EDU willflash for 2 seconds, then godark, indicating that thecurrent position has beenstored as the Open Limit.SIVOIA QED Wireless Roller 64 Installation Instructions 18TM
12Setting Limits from the EDU (continued)Setting the Close Limit from the EDU12.4Tap the “Close LimitButton” ( ). The greenLED on the roller ShadeEDU will turn on steady,indicating that the EDU isin “Set Close Limit Mode”.12.5Adjust the position of theEDU to the desired CloseLimit using the adjustmentbuttons ().12.6Press and hold the “CloseLimit Button” ( ) for 5seconds. The green LED onthe roller shade EDU willflash for 2 seconds, then godark, indicating that thecurrent position has beenstored as the Close Limit.SIVOIA QED Wireless Roller 64 Installation Instructions 19TM
13Finish System ProgrammingThe Sivoia QED shade is now installed, wired, and the OPEN/CLOSE limits for each shade havebeen set.The next step is to finish programming the system, using the HomeWorks Illumination Software.SIVOIA QED Wireless Roller 64 Installation Instructions 20TM
14TroubleshootingSymptomShade will not move usingadjustment buttons on EDU.Solution.EDU is not powered - check EDU Power.By unplugging and re-plugging in EDU.LED should light for 5 seconds.Shade is caught on something - free shade.Shade is not programmed to keypad or event.Shade does not fully open or fully close.Limits have been set incorrectly - refer to “setopen limit” and “set close limit” sections on re-setlimits using HW1 Software.Shade fabric is caught on something - free shade.Check that brackets are mounted level.Check that fabric is tracking correctly onthe shade tube.Check that brackets are centered.Fabric not level.Fabric not centered over window.Shade does not move smoothly.Check for binding of shade fabric on sidechannels.Check fabric tracking.Wireless Shade can not be addressed. .Shade is out of RF communications range.Move RF signal repeater or RF processor towithin 30 feet (9m) of shade.SIVOIA QED Wireless Roller 64 Installation Instructions 21TM
IVOIA QED Wireless Roller 64 Installation Instructions 22TMLocationSerialNumber
Technical AssistanceWORLDHEADQUARTERSCUSTOMER SERVICE/E-MAILLutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036United StatesTel: 1-610-282-3800Fax: E/ORDERINGINTERNET:TECHNICAL SUPPORT& SERVICESUSA 1-800-523-9466 –24 hours/7 dayswww.lutron.comUSA 1-888-LUTRON108.00 - 20.00 ESTLimited WarrantyLutron offers an 8-year limited warranty for ourshading systems. Please contact customerservice or visit our website for a completewarranty statement.Lutron reserves the right to make improvements or changes to these products withoutprior notice. Although every attempt is made toensure that this information is accurate and upto date, please check with Lutron to confirmproduct availability, the latest specifications,and suitability for your application.These products may be covered by one ormore of the following US patents:5,983,783and corresponding foreign patents.US and foreign patents pending.Lutron, the Sunburst logo, and Sivoia areregistered trademarks, and Sivoia QED is atrademark of Lutron Electronics Co., Inc. 2006 LUTRON Electronics Co., Inc.Printed in the U.S.A.P/N 045-119 REV. AFCC InformationNOTE: This equipment has been tested andfound to comply with the limits for a Class Bdigital device, pursuant to part 15 of the FCCrules. These limits are designed to providereasonable protection against harmfulinterference in a residential installation. Thisequipment generates, uses and can radiateradio frequency energy and, if not installed andused in accordance with the instructions, maycause harmful interference to radio or televisionreception, which can be determined by turningthe equipment off and on, the user isencouraged to try to correct the interferenceby one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between theequipment and receiver. Connect the equipment into an outlet on acircuit different from that to which thereceiver is connected. Consult the dealer or an experiencedradio/TV technician for help.Caution: Changes or modifications notexpressly approved by Lutron Electronics Co.could void the user's authority to operatethis equipment.Industry CanadaInformationThe term “IC” before the radiocertification number only signifies thatIndustry Canada technical specificationswere met.
Antenna mounted parrallel with shade use these configurations. When Pocket or Fascia is not used. Antenna mounted straight down. Antenna clipped to bottom of Pocket or Fascia - This configuration provides optimal performance with metal Fascia. Note: Lutron has tested this pro
Lutron Sivoia QS Roller 225 TM shades Sivoia QS roller 225 shades Product Specification page 1 of 12 P/N 086-105 REV A Sivoia QS roller 225 . roller 100, roller 200CW, or roller 225 TM Up to 1 seeTouch QS keypad 500 ft (150 m) 200 ft (60 m) 125 ft (35 m) 2 Sivoia QS roller 64, 30 sq ft (2.75 sq m) each
than or equal to pocket width. 1.1 Sivoia QED Installation Instructions In-Line Coupled Roller Blind Addendum To be used in conjunction with: Sivoia QED Wall-Mount Instructions P/N 045-102-12 Sivoia QED Ceiling-Mount Instructions P/N 045-103-12 Sivoia QED Jamb Moun
Lutron Sivoia QS Roller 100 TM shades Sivoia QS roller 100 shades Product Specification page 3 of 16 P/N 086-106 REV A Sivoia QS roller 100 TM shade options Mounting options Depending on window dimensions, brackets can be mounted inside the window frame, outside the window frame, or in a
Lutron Sivoia QS Roller 64 TM shades Sivoia QS roller 64 shades Product Specification page 3 of 6 P/N 086- 02 REV A Sivoia QS roller 64 TM shade options Mounting options Depending on window dimensions, brackets can be mounted inside the window frame, outside the window frame, or in a
Use this document as a reference when measuring windows for Sivoia QS and Sivoia QS Wireless Roller 20, 64, 100, 150, 225, and 300 non coupled roller shades, as well as Sivoia QS Triathlon, Sivoia QS Triathlon WIDR, and Lutron Manual and . This is because the light gaps of a Lutron roller shade are at least 1/2 in (13 mm), and there is little
Page 2 Sivoia QS Wiring and Programming Guide Sivoia QS Wiring and Programming Guide Sivoia QS Drives are available for control of Draperies, Roller Shades, Venetian Blinds, Sheer Blinds, and Tensioned Shades. Sivoia QS Shades, Blinds, and Draperies can be controlled as part of a QS System, incorporating GRAFIK Eye QS lighting controls, or as a Window treaments only System, without .
Lutron Sivoia QS . GRX-CBL-346S-500 None Up to 8 seeTouch QS keypads 1200 ft (350 m) 500 ft (150 m) 300 ft (75 m) 1 Sivoia QS roller 64 TM, roller 100, roller 200CW, . QS RS232 Interface Wiring Type Key Type A Communications Link: 4
Lutron 05 Curved fascia Sivoia QED roller 64 can be installed with a top back cover and curved fascia for a clean, minimal look. Squared off fascia is also available. Roller tube end cap Provide a clean look for a system installed without fascia or pocket. Available in white only. Pocke
