ROLLER CATALOG - Omni Metalcraft Corp.
ROLLER CATALOG
TABLE OF CONTENTSGENERAL INFORMATIONPAGECONTENTPAGETube Sizes and Material45-9/16"43Axle Retention and Material46"43Construction46-1/2"44Bearing Features and Lubrication48"44Sprocket Information4Groove Information5TAPERED ROLLERSLoad Capacity Reference51"Taper Specific Information5-6Customizing Rollers6-7Stainless Steel Roller Information8-947-49STAINLESS STEEL ANDPVC ROLLERSBearing Selection Guide101"Coatings and Sleeves111.9"Gravity Roller Quote Sheet121-1/2"55Sprocketed Roller Quote Sheet132-1/2"56Grooved Roller Quote Sheet14Tapered Roller Quote Sheet15STRAIGHT ROLLERS5253-54SPROCKETED "1-1/2" pipe2"24-26GROOVED R ROLLERS4"38-401-7/8" - 2"4-1/4"415"4284POLY RIB ROLLERS1.9" - 2-1/2"Additional options & customs available 989.358.700088 rollers@omni.comSR-3nnnnSR-3
Omni Metalcraft Corp. offers thousands of tube, axle, and bearing combinations for gravity andpowered applications. This Roller Catalog, which focuses on our expansive offering of standard,pre-engineered rollers, can be used for guidance when selecting standard rollers. For customroller applications, please contact Omni Metalcraft’s Roller Division. We appreciate your businessand hope that you find this catalog useful.For more information, contact one of our customer service representatives.GENERAL INFORMATIONTUBE SIZES AND MATERIAL OPTIONSn Tube diameters range from 1" to 8"n Tube is specified by the Outer Diameter (OD) and tubewall thicknessn Pipe is specified by the Inner Diameter (ID) and aschedule number that represents wall thicknessn Roller tubes are available in the following materials:- Mild (low carbon) steel- Galvanized steel- Stainless steel- Aluminum- PVC (pipe)- Industrial steel pipeAXLE RETENTION AND MATERIAL OPTIONSn Axles up to 3/4" (dia or hex) are available with thespring or cotter pin retentionn Axles larger than 3/4" (dia or hex) are not available withthe spring retentionn Round axles 3/4" dia and larger are available withD-end retentionn Axles, springs and cotter pins are available in carbon steeland stainless steeln Other retention styles are available upon requestCONSTRUCTIONCrimped / Swaged – Tube material is formed down over thebearing to hold it in place. Bearings installed in this manner arenon-replaceable.Counter Bored / Press Fit – Tube is counter bored to thecorrect inside diameter for the bearing to be press fit. Bearingsinstalled in this manner are replaceable.BEARING FEATURES(reference Bearing Selection Guide page 10)Seals – Keep contaminants out while helping retain greasewithin the bearing. Seals are made of Teflon , felt, rubber,nylon and Mylar depending on the bearing type.Shields – Keep contaminants out. Can be used in conjunctionwith a seal. Generally made of steel.Labyrinth Seals – A series of interlocking passageways in thebearing housing to help prevent leakage.Ball Retainer – Holds ball bearings evenly spaced. Makes for aquieter bearing and improves bearing life.Set-Screws – Locks the inner race onto the axle.Flanged – Flanges are located on the outer race of the bearing.Flanges create a fixed bearing extension from the end of thetube. Flanged bearings cannot be recessed into tubes.Unflanged – Bearings that have a cylindrical body that can bepressed completely into a tube if needed.4-SRnnnnAdditional options & customs availableBEARING LUBRICATIONO (Oiled) – Generally used in gravity applications requiring a lowcoefficient of friction. Temperature range of standard oil is 0 to200 F.GP (Grease Packed) – Generally used in powered applications.Temperature range of standard grease is -10 to 225 F. Alsosuitable for humid applications.Regreaseable – Same features as GP bearings, but include adrilled inner race or an extended back closure to accept moregrease through a fitting located on the end of the axle withoutbeing removed from the roller. The frame thickness of theconveyor is required to determine regrease hole location.GENERAL SPROCKET INFORMATION(reference quote sheet drawing page 13)n Sprockets available on all roller sizes with 11 gaugeor thicker tube walln Standard sprockets are A-plate for 40, 50, 60 and80 series chainn Other sizes and styles are available upon requestn Sprockets can be placed anywhere along the length ofthe tube provided they are clear of the bearing and willnot cause chain interferenceGENERAL GROOVE INFORMATION(reference quote sheet drawing page 14)nGrooves available on 1-3/8", 1-5/8", 1-7/8", 1.9", 2"and 2-1/2" OD rollersn5/16" narrow grooves are made for 3/16" dia belt. Narrowgrooves can be placed as close as 5/8" from center ofgroove to center of groove.n1/2" wide grooves are made for 1/4" dia belt. Widegrooves can be placed as close as 1" from center ofgroove to center of groove.nGrooves can be placed anywhere along the length of thetube provided they are clear of the bearing and are set atleast to the minimum centers noted above. 989.358.7000 rollers@omni.com
CONVEYOR ROLLER SELECTION FOR A GIVEN LOADConsider only 2/3 of the rollers under the product when calculatingrequired roller capacity because conveying surfaces are nottypically perfectly flat.Roller Diameter and AxleMaximum ProductWeight (lbs)1" OD - 5 /16 hex1 3/8" OD - 5/16 hex1.9" OD - 7/16 hex2-1/2" OD - 11/16 hex3-1/2" OD - 1-1/16 hex3-1/2" OD - 1-7/16 dia4" OD - 1-7/16 dia5" OD - 1-11/16 dia3006001,5003,5006,00010,00015,00025,000Example Equation300 lbs. capacity roller x 3 rollers 900 lbs.900 lbs. x 2/3 Rule 600 lbs. load capacity per 3 rollersThe above guidelines assume "0" shock load and are notapplicable for 3 or more lanes. When calculating loadcapacity for rollers in fork lift loading areas, Omni MetalcraftCorp. recommends tripling the required roller capacity due toshock loading.TAPER SPECIFIC INFORMATIONOmni has a line of pre-engineered tapered rollers to meet yourconveyor curve application needs. This section is specificallydevoted to information unique to tapered rollers.Tapered rollers are used in gravity or powered conveyor turns.Tapered rollers are designed to match the inside radius of theCenter ofCurven If the taper rate is not true fora given curve then the product willbecome skewed around the curve.Additional options & customs availablecurve. This helps to maintain product orientation around a curve.Our standard rollers are designed for industry standard insideradius dimensions. Custom tapered rollers can be made to workwith custom inside radius dimensions.Center ofCurven If the taper rate is true it increases thelikelihood of maintaining leading edgeproduct orientation through the curve. 989.358.7000 rollers@omni.comnnnnSR-5
TAPER SPECIFIC INFORMATION (CONTINUED)TAPER ROLLER TUBE SIZES AND MATERIAL OPTIONSn Two standard taper tube sizes both available in mildsteel and galvanized steeln 1-1/2" OD to 1" OD x 18 Ga wall with a flat section atthe large end (1/2" to 4-1/2" of flat depending on BF)n 2-1/2" OD to 1-11/16" OD x 14 Ga wall with a flatsection at the large end (1/2" to 8-11/16" of flatdepending on BF)TAPER ROLLER AXLE RETENTION ANDMATERIAL OPTIONSn 1-1/2" OD to 1" OD tapers are standard with5/16" hex axlesn All larger tapers are standard with 7/16" hex axlesn All tapers are available in spring or cotter pin retentionn Other retention styles and axle sizes areavailable upon requestTAPER ROLLER SPROCKET INFORMATION(reference quote sheet drawing page 11)n Sprockets available standard on 2-1/2" OD to1-11/16" OD tapersn Standard sprockets are A-plate for 40 and50 series chainnSprockets are placed on the large OD end as a standard.Sprockets can be placed anywhere along the lengthof the tube provided they are clear of the bearing andwill not cause chain interference.TAPER ROLLER GROOVE INFORMATION(reference quote sheet drawing page 11)n Narrow grooves are available on 1-1/2" OD to 1" ODand 2-1/2" OD to 1-11/16" OD tapersn Wide grooves are only available on 2-1/2" OD to1-11/16" OD tapersn Grooves can only be placed on the tapered section ofthe roller provided they are clear of the bearing and areno more than 3-3/4" inches from the end of the tubeCUSTOMIZING ROLLERSFlanges – Flanges can be welded to the tube to guide theproduct. Standard flanges are available for 1.9", 2-1/2",2-9/16" and 3-1/2" OD rollers. Other sizes may beavailable upon request.Center Support Puck – Center support pucks can beinstalled in a roller to provide extra roller capacity at longerlengths. Pucks are available for most axles 11/16" hexand smaller.Ultrex Sleeves – Loose fitting Ultrex sleeves installed oversprocketed rollers are designed to be able to spin on theroller surface for low pressure accumulation applications.Boss – Steel plate designed to fit in the ID of the tube.As a standard, these plates are recessed into the tube andwelded in place. The plate is designed to fit thecorresponding bearing or to be welded directly to the axle.6-SRnnnnAdditional options & customs availableHeat Treat – All heavy-wall rollers (11 Ga and thicker) areavailable with a hardened tube surface. This provides extraresistance to surface wear and dents. Omni has twodifferent heat treat standards. They are dependent on thelength of the roller.n Rollers up to 60" will be to a Rockwell C 58-62 Hardnesswith a Case Depth of .018"-.022"n Rollers 60" to 84" will be to a minimum of Rockwell C 40Hardness with a Case Depth of .035"n Special heat treat specifications may be availableFINISHESnZinc Plating – All mild steel roller tubes and axles areavailable in one of our two standard zinc plating colors;gold or silver/clear. Zinc plating is a highly corrosionresistant finish with aesthetic appeal. Other types ofmaterial plating may be available.nPowder Coat – A paint application process where apowder material is applied to the surface of the rollerusing an electrostatic charge. The applied powder isthen heat cured to form a smooth, very durable finish.Available in a clear coat or any of Omni’s color options.n Sand Blasting – Can be used to give a matte/non reflective finish to the tubeSPECIAL ODS (STRAIGHT ROLLERS)n Standard press fit bearings can be used withspecial OD tubesn Bearings can be press fit directly into the tube if thetube wall is of sufficient thicknessn If the bearings do not fit directly into the tube a bosscan be usedn Neither design option can be used with crimpstyle bearingsSPECIAL ODS (TAPER ROLLERS)Special large end and/or small end ODs can be manufacturedupon request depending on the roller construction.n Tapers can start as large as 5" OD and go down to 1" ODn Special tapers can be manufactured as true tapersto fit most radiin Special tapers can be made with no flat on the large endn Some special tapers are available with grooves.This is determined based on the size and lengthof the taper tube.WELD-OVER TAPER SHELLThese tapered tubes are designed to fit over a straight roller andbe welded in place. It is recommended that the small end of thetaper is a minimum of 1/4" larger than the straight roller ODAXLE MACHININGOmni can provide optional axle retention/machining. Page 7 aresome of the axle machining options that are available.(enlarged to show detail) 989.358.7000 rollers@omni.com
AXLE MACHINING OPTIONSDrill and Tap (Female Thread)Threaded (Male Thread)Milled FlatMilled SlotSnap Ring GrooveTurn DownSPECIAL TUBE CONSTRUCTIONOmni can provide special tube construction for many differentapplications. Below are some of the different tube constructionoptions that are available.Concave RollerSprocketed HubBow-Tie RollerTrapezoidal CrownV-Groove HubFlangesAdditional options & customs available 989.358.7000 rollers@omni.comnnnnSR-7
STAINLESS STEEL ROLLER INFORMATIONPremium Class (P-Class)P-class rollers are made from all stainless steel components and are intended for use infrequent washdown, high corrosive and food processing applications.n Manufactured with 304 stainless steel, mill finish materials (unless otherwise noted)n Stainless steel or polymer roller bearingsn Washdown ratedn Stainless steel sprockets and fastenersn FDA/USDA approved materialsn Continuous MIG weldsn Rollers with thru-bore bearings are NOT water-tight; liquid may become trapped insideAdditional Options- Polished stainless steel finishes- 316 stainless steel materials- Special "water-tight" roller designs utilizing blind bore bushingsDeluxe (D-Class)D-class rollers are made of combinations of corrosion-resistant material and carbon steelmaterials. They are intended for use in occasional washdown and low corrosive applications.n Standard roller designs (zinc plated, galvanized, PVC, stainless steel or aluminum tubing)n General purpose roller bearingsn General purpose sprockets and chainn Zinc plated fastenersn Rollers with thru-bore bearings are NOT water-tight; liquid may become trapped insideSurface Finishes AvailableMill Finish – Mill Finish also known as unpolished finish is the standard finish for rollers unlessotherwise requested by the customer. A mill finish is a bright, smooth, semi-reflective and nondirectional finish. Exact visual appearance can vary based on different grades and thicknessesof stainless steel. Pitting, scratches, welds and tool marks may be visible on the surface. Theseblemishes cannot be blended to recreate an original mill finish appearance. These areas willremain blemished unless additional surface finishing operations are performed.Glass Bead Blasted Finish – Glass bead blasting produces a bright uniform matte or frostedfinish with low reflectivity and no directionality. It reduces glare from shiny stainless steel whileretaining a smooth feel. Although the surface has a consistent look it may contain pitsand scratches. The maximum surface roughness is Ra of 125 micro-inches.Sand Blasted Finish – Sand blasting, similar to glass bead blasting, uses a more abrasivemedium. This produces a duller and less smooth finish than glass bead blasting. The surfacemay contain pits and scratches.Polished Finish – Also known as brushed or satin finish. A polished finish is the result ofadditional mechanical operations which include grinding, polishing and buffing that are intendedto change the appearance and condition of stainless steel metal surfaces. The most commonstainless steel cosmetic polished finish is described as a No. 4 finish. It is a bright, uni-directionalfinish with a visible "grain" which prevents mirror reflection. It is obtained by finishing with a 120150 mesh abrasive, following initial grinding with coarser abrasives and has a surface roughnesswith a maximum Ra of 32 micro-inches. Areas where welds and tool marks were cleaned up canbe blended or repaired by using the same or similar polishing methods that were used to createthe original polished finish. Sprocketed rollers can only be polished on the effective width.8-SRnnnnAdditional options & customs available 989.358.7000 rollers@omni.com
STAINLESS STEEL ROLLER INFORMATION (CONTINUED)Bushings (Roll End Bearings)Bushings, or Roll End Bearings, can be used in place of traditional ball bearings in rollers. In applications with speedsless than 150 FPM they offer many advantages.n No moving parts to break downn No lubrication to be washed away or dry outn Equivalent load capacity to ball bearingsn Fit in any tube size or tube materialn Can be custom built for uncommon tube and axle size combinationsn Blind bore designs with stub axles for “water-tight” rollersn Free-draining designsn Available in a wide variety of materialsBased on the material they are made from bushings can be used in many applications.n Sanitary and food applicationsn High temperature applications (up to 550 F)n Low temperature applications (down to -50 F)n Excessively abrasive dust or debris applicationsn Underwater applicationsn Corrosive environmentsAdditional options & customs available 989.358.7000 rollers@omni.comnnnnSR-9
BEARING SELECTION GUIDEeldsvEnLowLowLight DutyGravityConveyorCorrosiveWetHighLowLowGravity andLineshaftConveyorMildHighMediumMediumGravity y DutyGravity andPoweredConveyorDirtyMediumMediumHighestHigh SpeedPoweredConveyorMildLowHighestHighHeavy DutyPoweredand GravityConveyorVery DirtyLowMediumHighHigh orAllMediumycitWHY THIS BEARING?aapCPlastic Lowest capacity No lubrication required Capable of operating submerged in liquid Not for use with high speeds or powered conveyor Ideal for washdown with harsh detergents Molded plastic bodies and stainless steel ballstenryoenv esCo TypepeSnmiroseiNovLeUnground Crimped (Non-Precision) Most cost effectiveLowest coefficient of friction, easiest to turnZinc plated for mild corrosion resistanceNot for use with high speedsStamped metal housing with very loose tolerancesFull complement of balls which are not separatedUnground Press Fit (Non-Precision) More capacity than crimpedCan be replaced for longer roller lifeMore sealing options availableZinc plated for mild corrosion resistanceStamped metal housing with very loose tolerancesFull complement of balls which are not separatedSemi-Precision More capacity than ungroundCapable of higher speeds than ungroundSuperior seals over ungroundCan be replaced for longer roller lifeMachined metal housings with tighter tolerancesBall retainer keeps the balls separated and evenlyspacedPoly Housed ABEC style (Precision) Most common ABEC styleMost cost effective ABEC styleHighest possible speedsLong service lifeBetter seals than semi-precisionAll Metal and Insert ABEC style (Precision) All metal partsBest seals and shields availableHighest capacity possibleCan be replaced for longer roller lifeInsert bearings feature set-screws to lock onto axle andprevent side-to-side movementHigh quality steel, heat treated to uniform hardness andground to a micro finishTightest tolerances availableFramesaver (Precision) Same benefits as Poly Housed ABECUses tapered hex stub axle designAxle fits tightly in worn frame holesPrevents additional frame wearMetal or plastic axles availableBushings No moving parts to wear outUncommon sizes availableLong service lifeHeavy duty capacity at slow speedsHigh temp materials availableAbrasion resistant material availableFood grade materials available*The information provided on this bearing guide is for general reference only. There are many exceptions and we encourage you to contact our qualifiedstaff to answer any questions you may have.For more detailed drawings and additional bearings reference our Bearing Index.10-SRnnnnAdditional options & customs available 989.358.7000 rollers@omni.com
COATINGS AND SLEEVESDurometerLOWERSofter, better cushion for product protection, reduces noiseand more grip for driving forceHIGHERHarder, more resistant to cutting and tearingRangeDurometer:ComparableToRubber FamilyFood Grade FamilyMillable Urethane FamilySleeve FamilyCost effective, generic coating. Notrecommended for non-markingapplications.Used for food and non-markingapplications.Most durableEconomical, replaceable andsuitable for numerous materialhandling applications.*95A Orange Millable Urethane(MAX TEMP 212 F)Most durable of all compounds95A: SolidFork Lift Tires95A Black Millable Urethane(MAX TEMP 212 F)Same as above except black in color. Notsuitable for non-marking applications.90A: PhoneCord80A: ShoeHeel70A: RunningShoe Sole90A Orange Millable Urethane(MAX TEMP 212 F)90A Black Aquaflex(MAX TEMP 275 F)Most common black rubber compound80A Black Neoprene(MAX TEMP 250 F)Meets some specific food graderequirements80A Off-White Nitrile(MAX TEMP 230 F)Most durable food grade compound90A Green Urethane(MAX TEMP 185 F)Mid-range urethane compoundMost durable sleeve option80A Orange Millable Urethane(MAX TEMP 212 F)83A Orange Urethane(MAX TEMP 185 F)Mid-range urethane compound(available in red also)Most common for roller coverings(available in black also)70A Black Millable Urethane(MAX TEMP 212 F)70A Black Carboxylated Nitrile(MAX TEMP 275 F)Softest urethane compound Common forpulley laggingsMost common pulley lagging65A Black Aquaflex(MAX TEMP 275 F)Most common soft black rubber65-60A: CarTire Tread60A Black Neoprene(MAX TEMP 250 F)Most commonly used in glass handling60A Black SBR(MAX TEMP 220 F)Softest back rubber compound60A Gray Vinyl(MAX TEMP 160 F)60A Off-White Carboxylated Nitrile(MAX TEMP 275 F)Higher chemical resistance thanurethane sleevesMid-range food grade compound60A Off-White Neoprene(MAX TEMP 250 F)Same durometer as above but differentchemical resistances40A Tan Natural Rubber(MAX TEMP 212 F)40A: PencilEraserSoftest of all compounds*Installation tool available. Contact one of our customer service representatives for more information.ADDITIONAL OPTIONS AVAILABLETAPERED URETHANE SLEEVES Convert standard straight rollers into tapered rollersGROOVES Multiple patterns availablePROFILES Concave, convex, crowned, bow-tie and taperedRed Urethane Coated 6” RollersAdditional options & customs availableMachined Bow-Tie Profile MillableUrethane Coated Rollers 989.358.7000 rollers@omni.comnnnnSR-11
GRAVITY ROLLER QUOTATION WORKSHEETCompany:Date:Contact: Quote Due:Desired Delivery:Phone No.: Contact Email: State:Omni Sales Contact: Quote #:Quantity:Between Frame Width (BF):Overall Cone (OAC) (if roller is not in frame):Roller Diameter:Wall Thickness (Gauge):Tube Material/Finish:Type of Bearing:Axle Size: (Hex or Round)Axle Length: (or Standard)Pin Retained:Spring Retained:Load Capacity Required:Note: Between Frame (BF) is the distance between the frames of the conveyor. The BF measurement is needed toensure proper fit into the conveyor. If the roller is not in the conveyor provide the Overall Cone, the length of the rollerfrom bearing tip to bearing tip. (See our Roller Measurement Guide for more information) Utilize the drawing below todepict more detailed specifications.BF1/16 (TYP)O.A.C.WALLFRAMEFRAMEOD xAXLEProposal Drawing Required:12-SRnnnnAdditional options & customs available 989.358.7000 rollers@omni.com Yes No
SPROCKETED ROLLER QUOTATION WORKSHEETCompany: Date:Contact: Quote Due: Desired Delivery:Phone No.: Contact Email: State:Omni Sales Contact: Quote #:Quantity:Between Frame Width (BF):Overall Cone (OAC) (if roller is not in frame):Roller Diameter:Wall Thickness (Gauge):Tube Material/Finish:Type of Bearing:Axle Size: (Hex orRound)Axle Length: (or Standard)Pin Retained:Spring Retained:Sprocket Size:Load Capacity Required:Note: Between Frame (BF) is the distance between the frames of the conveyor. The BF measurement is neededto ensure proper fit into the conveyor. If the roller is not in the conveyor provide the Overall Cone, the length ofthe roller from bearing tip to bearing tip. (See our Roller Measurement Guide for more information) Utilize thedrawing below to depict more detailed specifications.BFO.A.C.1/16 (TYP)WALLFRAMEFRAMEOD xSPROCKETSCLCLAXLEProposal Drawing Required:Additional options & customs available 989.358.7000 rollers@omni.com Yes NonnnnSR-13
GROOVED ROLLER QUOTATION WORKSHEETCompany: Date:Contact: Quote Due: Desired Delivery:Phone No.: Contact Email: State:Omni Sales Contact: Quote #:Quantity:Between Frame Width (BF):Overall Cone (OAC) (if roller is not in frame):Roller Diameter:Wall Thickness (Gauge):Tube Material/Finish:Type of Bearing:Axle Size: (Hex or Round)Axle Length: (or Standard)Pin Retained:Spring Retained:Groove Center Line:Load Capacity Required:Note: Between Frame (BF) is the distance between the frames of the conveyor. The BF measurement is neededto ensure proper fit into the conveyor. If the roller is not in the conveyor provide the Overall Cone, the length ofthe roller from bearing tip to bearing tip. (See our Roller Measurement Guide for more information) Utilize thedrawing below to depict more detailed specifications.BFO.A.C.1/16 (TYP)WALLFRAMEFRAMEOD xCLCLAXLEProposal Drawing Required:14-SRnnnnAdditional options & customs available 989.358.7000 rollers@omni.com Yes No
TAPERED ROLLER QUOTATION WORKSHEETCompany: Date:Contact: Quote Due: Desired Delivery:Phone No.: Contact Email: State:Omni Sales Contact: Quote #:Quantity:Between Frame Width (BF):Overall Cone (OAC) (if roller is not in frame):Roller Diameter at Small End:Roller Diameter at Large End:Wall Thickness (Gauge):Tube Material/Finish:Type of Bearing:Axle Size: (Hex or Round)Axle Length: (or Standard)Pin Retained:Spring Retained:Groove Center Line: (if applicable)Sprocket Size: (if applicable)Flat Length: (if applicable)Load Capacity Required:Note: Between Frame (BF) is the distance between the frames of the conveyor. The BF measurement is needed to ensure proper fit into theconveyor. The BF dimension allows 1/16" clearance between the extension on the bearing and the side frame at each end. If the roller is notin the conveyor provide the Overall Cone, the length of the roller from bearing tip to bearing tip. (See our Roller Measurement Guide for moreinformation) Utilize the drawings below to depict more detailed specifications.The small diameter end of a taper is meant to be installed higher in the frame than the large diameter end. The top of the tapered surfaceof the tube should be horizontal. The locations of features like sprockets, grooves, tapered shells and flats should be measured from thenearest bearing tip or OAC. Measurements should always be parallel with the axle to ensure proper location.GRAVITY TAPERBFOAC1/16" (TYP)BF1/16" (TYP)1/16" (TYP)BFBFOACOACOAC1/16" (TYP)FLATFLATPOWER TAPERFLATGROOVED OAC-CLOAC-CLCL-CLWELD-OVER POWER TAPEROAC-CLOAC-CLCL-CLCL-CLOAC-CLOAC-CL CL-CL CL-CLProposal Drawing Required:Additional options & customs available 989.358.7000 rollers@omni.com Yes NonnnnSR-15
STRAIGHT ROLLERS
STRAIGHT Roller1" Dia x 16 Ga1" Dia x 14 Ga1-1/4" Dia x 16 GaStandard Specifications1" OD x 16 GaTubeMaterialBearingGradeAxle SizeBearingAssemblyBearingProtectionBearing PartNumber1/4" Dia.5/16" Dia.Mild SteelFeatures102245-O102272-OUngroundPress FitOpen15/16" HexGalvanizedFlo-CoatRoller Part 333824620747N/A299342067744983N/A1" OD x 14 GaUngroundABECUnground1/4" Dia.Mild Steel5/16" Dia.Press FitOpenShieldedOpen102245-O102149 43538435404354243544N/A1-1/4" OD x 16 Ga5/16" HexMild Steel3/8" Hex7/16" HexUngroundPress FitOpenSTYLE ONE3N/ASTYLE THREESTYLE TWOLoad CapacityBEARINGS(BF) Between 8-SRnnnnAdditional options & customs available 989.358.7000 rollers@omni.com
1-3/8" Dia x 18 GaSTRAIGHT RollerStandard Specifications1-3/8" OD x 18 GaTubeMaterialBearingBearing PartAxle Size Bearing GradeBearing ProtectionAssemblyNumberAluminum1/4" -GP215/16" HexCrimpedABECSTYLE ONEShielded2FeaturesRoller PartNumberSpringPinRetained 404237442370STYLE TWOLoad CapacityBEARINGS(BF) Between 14231-GP29529425219816213611710188776758Additional options & customs available 989.358.7000 rollers@omni.comnnnnSR-19
STRAIGHT Roller1-3/8" Dia x 16 GaStandard Specifications1-3/8" OD x 16 GaTubeMaterialBearingGradeAxle Size1/4" Dia.1/4" Hex5/16" ss FitSealed and ShieldedShielded114231-GP3Open110528-O4ABEC1/4" 16" HexGalvanizedFlo-CoatBearing PartNumberUngroundMild Steel5/16" HexRoller Part on5/16" HexABECSTYLE ONEPress FitSealed and ShieldedCrimpedShieldedSTYLE THREESTYLE STYLE FOURLoad CapacityBEARINGS111692-O(BF) Between dditional options & customs available 989.358.7000 79743797544845423874238340124N/A4238842384
1-3/8" OD x 3/16"STRAIGHT RollerStandard Specifications1-
rollers@omni.com Omni Metalcraft Corp. offers thousands of tube, axle, and bearing combinations for gravity and powered applications. This Roller Catalog, which focuses on our expansive offering of standard, pre-engineered rollers, can be used for guidance whe
115289-F - OMC ROLLER OPTIMIZATION - 01/2018 2009 Omni Metalcraft Corp. P.O. Box 352 n Alpena, Michigan 49707 Phone 989.358.7000 Fax 989.358.7020 rollers@omni.com www.omni.com ROLLER ORDERING AND OPTIMIZATION ROLLER ORDERING AND OPTIMIZATION PROGRAM PROGRAM Omni Metalcraft Corp. can help you sell mor
2009 Omni Metalcraft Corp. P.O. Box 352 n Alpena, Michigan 49707 Phone 989.358.7000 Fax 989.358.7020 info@omni.com www.omni.com Featuring Intralox Belting Technology ROLLER ORDERING AND OPTIMIZATION PROGRAM Omni Metalcraft Corp.’s Roller Ordering and Optimizati
cDLR chain DRiVen LiVe RoLLeR conVeYoR Why CDLR? n Roller size and centers optimized to handle nearly any load n Positive drive using roller to roller chain and sprockets n Withstands even the toughest environments and abrasive applications n Robust, welded construction using structural steel with nearly unlimited between
4 TIMKEN METRIC TAPERED ROLLER BEARINGS BEARING DATA TIMKEN METRIC TAPERED ROLLER BEARINGS Bore Part Number Dimension Series (ISO 355) Bearing Dimensions Bore d O.D. D Width T B Width C mm mm mm mm mm mm 15 30302 2FB 15.000 42.000 14.250 13.000 11.000 17 30203 2DB 17.000 40.000 13.250 12.000 11.000 30303 2FB 17.000 47.000 15.250 14.000 12.000 20 File Size: 279KBPage Count: 20Explore furtherTapered Roller Bearing Catalog Timkenwww.timken.comTimken Tapered Roller Bearing Catalog - TIMKEN - PDF .pdf.directindustry.comTimken Metric Tapered Roller Bearing Catalogwww.timken.comTIMKEN METRIC TAPERED ROLLER BEARINGSwww.timken.comTimken-Tapered Roller Bearing Catalogue - THE TIMKEN .pdf.aeroexpo.onlineRecommended to you b
Omni Metalcraft Corp. has been renowned for the superior material handling components that we supply. Our quality products (both standard and custom) are a great source of pride among the entire . Bed rollers are
Omni Metalcraft Corp. All weights listed in this section DO NOT include crating. Quantity available for shipment is contingent upon quantity in stock at time of order. All orders subject to Omni Metalcraft Corp.’s Standard Terms and Conditions of Sale. P.O. Box 352 A
The Omni Advantage Omni Metalcraft Corp. is your single source for conveyors and material handling equipment. We offer a comprehensive line of products to meet your needs. From transporting totes and aligning packages, to rotating engines and diverting tires, Omni is your solution
REGISTER OF LEGISLATION ISO 14001 Doc. Ref. Version Date Template Author Page ROL-SAMPLE-14001 1.0 24/08/2004 Mark Helm 2 of 10 Sovereign Certification Limited
