How To Assemble And Use The Supplement AKARI Origami
How to Assemble and Use the SupplementStructure of the AKARI Origami unitAKARI OrigamiOrigami lampshade"Celes"Assembly time for the LED stand : Approximately 30 minutesParts in the KitTri-color RGB LEDCoverAttachment receiverOrigami lampshade "CheckeredLantern"SwitchcoverBase unit (top)Dials (3)Color adjuster dialsScrews (9)Cover(If you remove the cover, you canaccess a pin connector forlinking to the "Japanino")SwitchLEDsupport columnAttachment for theCeles Attaching the circuit boards to the base unit3. Attach the circuit boards to the base unit (top)1. Attach the dials to the circuit boardsAttach the large and small circuitboards to the base unit (top) withscrews using the position of theswitch on the large circuit board as aguide for positioning the circuitboards. Slide the circuit boards in atan angle so that the dials protrude outthrough the slits in the base unit (top).Insert the switch cover at this time, aswell.Attach the three dials to the volume shafts on the two circuit boards. Orient thedials with the jagged sides up as shown in the diagram, and push them onto theposts all the way to the bottom.Base unit (bottom)DialVolume shaftsCircuit boardAttachment for theCheckered LanternOrigami paperFor the Checkered Lantern: 6 sheetsFor the Celes: 10 sheets with 3 pre-scored strips per sheet (cleanly cut thestrips apart using a utility knife or other cutting tool)* TANT N-8 paper is used for the origami paper here.* The origami paper is included in the case with the parts shown at left. Take care toensure that you do not accidentally throw the paper away.DialsScrewsMaterials used in this kitBase unit, attachments, dials, cover, switch cover, LED stand, and support column stand(white): ABSAttachment receiver (white): POMSupport column (white): PSScrews: Iron (chromium-plated)Battery contacts: Iron (nickel-plated)DialCircuitboardSlitBase unit(top)Pass the LED connector through thehole in the center of the base unit(top).LEDconnectorDialThings you will needA Phillips screwdriver, a utility knife, three AA batteriesCircuitboardVolume shaftsScrewsCircuitboards2. Connect the connector from the battery box to thecircuit boardInsert the battery connector coming out from the battery box on the base unit(bottom) into the battery connector receptacle on the circuit board.SlitScrewsDialSwitchBase unit(top)Switch coverBase unit (bottom)SlitLine the switch up with thispart here.Battery connectorBattery connectorreceptacle1Otona no KagakuAttach the switch cover to the black switch cap fromabove at an angle as shown in the picture. If you find itdifficult to attach the cover, loosen the screws on thecircuit board and move the circuit board back beforeattaching.2
R Assembling the Base Unit1. Place the cover on the base unit (bottom)Slide the cover into the slot on the base unit (bottom) to attach it.4. Attach the LED support column to the base unit(top)Push the LED connector part into the center of the base unit, andinsert the support column into the hole on the base unit. Line upthe notch on the hole with the protrusion on the support columnto insert, and then continue to turn the support columnclockwise until it clicks into place. Turning the LED ONAuto mode ATurn the switch on the base unit ONYou can set it to this mode by pressing the switch twice starting withthe switch in the Switch OFF position. Each color in the RGB LED willcycle through getting darker and brighter at different timing patterns.BThe timing patterns are as shown below, but the LED colors will roughly3060appear to change at random.GThe switch on the AKARI Origami unit is programmed to cyclethrough to the next operation in the sequence given each time thebutton is pressed. Each of the modes will be described below.SwitchONManualmodeAuto modeAAuto modeBSwitchOFF（秒）Changes from brighter to darker over a cycle lasting approx. 20 sec.R* The power will turn OFF automatically one hour after the switch was lastpressed.GManual modeBe sure tocheck the orientation ofthe cover.* Do not attach the cover if planning to link the AKARI Origami to the "Japanino",the supplement from Vol. 27 of the magazine.2. Fit the base unit (top) and the base unit (bottom)togetherSlowly andcarefullypush thecable intothe base unit.Place the base unit (bottom) onto the base unit (top) while lining theposition for the switch up with the switch on the base unit (top). Screwdown the base unit (bottom) plate using the three holes in the battery box,being careful not to let any wires get caught in the areas screwed down.In this mode, you can set the color to whatever you want by turning thedials. Each of the dials is positioned from the switch as shown in the picturebelow. Each dial is set up so that the light will get brighter when the dial isturned clockwise as seen from above. Adjust the dials to produce the coloryou want.LED supportcolumnClickChanges from brighter to darker over a cycle lasting approx. 48 sec.B30GREEN (G)OffBase unit (bottom)ScrewsCompletedRGets brighterBase unit(top)You can change theamount of supportcolumn visible below thelampshade by movingthis up and down.Check to make sure thatthe LED connector hasbeen pulled outside of thebase unit.Goes outRED (R)Attachment receiverGoesoutQ＆ABLUE (B)SwitchGetsbrighterQ: The LED will not light up even though the poweris ON.A: Confirm that the batteries are new and that theyhave been inserted in the correct direction. Check tomake sure that the connector on the LED supportcolumn and the battery connector have been securelyfastened in place. Also make sure that the wires have not gotten caughtin the screws and cut.SwitchQ: The light suddenly turns off unexpectedly.A: In order to conserve energy, there is an Auto OFF function that works toturn off power automatically one hour after the last operation has beenmade. Press the switch button again to turn the power back on.3. Attach the LED connector to the LED supportcolumnAttach the LED connector from the hole on the base unit to theconnector on the LED support column.Connector on the LEDsupport columnLED connectorQ: The brightness levels do not change when the dials are turned.For information on how to make andattach an origami lampshade, go topage 5 of this instruction booklet.60(sec.)（秒）Auto mode BYou can set it to this mode by pressing the switch three times starting with theswitch in the Switch OFF position. Each color in the RGB LED will changebetween bright and dark in order over equally long cycles. With this mode, youcan enjoy sharply defined color changes along with the blending of two colorsthat appears during the transitions from one distinct RGB color to the next.Gets brighterGoes outBaseunitChanges from brighter to darker over a cycle lasting approx. 28 sec.A: The unit may be in Auto mode. Press the switch button repeatedly untilthe unit turns off, and then press it just once more to turn it back on. Theunit will be in Manual mode, which allows you to adjust the brightnesslevels.OffOffGets brighter and brighter until it reaches the maximum brightness and thenstarts to get darker and darker.GB3060(sec.)（秒）A: The connector terminal connections may be bad. Unplug and plug theconnector several times and try again.RQ: The battery box gets hot.A: Remove the battery immediately, and then contact us using the contactinformation given below.GQ: I couldn't find any origami paper included with the supplement.A: The origami paper is slipped into the bottom of the Styrofoam tray whenthe kit is packaged. Double check the contents of the cardboard boxB again.Q: The switch is hard to press.3060（秒）A: Using the instructions given on the lower right of page 2, adjust theposition of the circuit board and reinsert the switch cover.Q: Dials are hard to turn.A: The base unit (top) and/or LED cable may be interfering with the dial(s).Remove the base unit (bottom) to check.Q: Screws are hard to turn.A: If you find that any screws are hard to turn, first try screwing in the screwsalone without trying to attach anything in order to prime the screwholes before assembling. Try to use a screwdriver with a secure bit (end).Q: The LED lighting is unstable.3Otona no Kagaku4
Putting the units togetherHow to Assemble and Use the SupplementHandHow to Make an Origami LampshadeTwo different types of paper are included with this supplement for making lampshades for the AKARI Origami unit. You can make boththe Checkered Lantern and the Celes and use each for a different location or type of situation. We've also included instructions on howto make another type of lampshade, although we did not provide any paper for this one. Please select some paper that you like and trymaking this one, too.1. Slide a "hand" onone unit into a "gap"on another unit so thatthey fit together tocombine the two units.2.Add a third unit to the assembly in thesame way.HandGapThe Checkered LanternValley fold(fold over)Mountain fold (foldunder)Time to complete: 30 min. 1 hr.GapThis lampshade was named the CheckeredLantern due to the fact that a checkeredpattern emerges when the finishedlampshade is attached and the LED is turnedon. You will use the set of six square sheetsof paper included in the supplement tomake this lampshade.The paper comes with pre-inserted foldlines, so just fold the paper along those lines.Use the side with indented fold lines as thefront side of the paper. The colored side ofpaper shown in the diagrams is the frontside.The two units should look like the diagrams when puttogether.As seen from the frontAs seen from the sideHow to fold one unit4. Rest the final unit on the top ofthe assembly, and slide the "hands"from the unit assembly into theopen "gaps" on the final unit.Turn thepaper over.This side is theback side of thepaper. The foldlines are raisedon this side.1.Take two opposite corners andfold them in to the center.235. Grasp one of the exposed"hands" with your fingers and curveit inward as shown in the picturebelow.3. Add a fourth unit on the front side.Add a fifth unit on the other side in thesame way.Turn the paperover.As seen from the top67.Fold as shown while takingcare not to let fold lines inoverlapping parts getcrooked.5. Open the two foldedcorners. Attaching the assembledlampshade to the LED stand4If you are not able to get the unitput together easily, apply glue toeach "hand" that you insert into a"gap" to assemble.10. Fold according to theinserted fold lines.6. Push the curved "hand"into the "gap."11.Fold the other side inthe same way.FinishedPush the attachment into one of the indentationsin the completed lampshade at whichevertriangle you want until it gets caught on the end.Be careful not to push the attachment into theinside of the lampshade.Attachment receiverUnit completedMake a total of six ofthese units.8.Open.127. Do the same for the otherexposed "hands."9 Insert a crease in theopposite side as well.Insert the LED support column into the hole onthe attachment, and push it in up to theattachment receiver. Then, turn the supportcolumn clockwise into the base unit.13.Open halfway.5Otona no Kagaku6
CelesValley fold(fold over)Mountain fold (foldunder)This lampshade was named Celes from the word Celestial because it glitters brightly likethe stars in the sphere. You will use thirty strips measuring 28 cm 4.5 cm (1.1 in. 0.17 in.)cut from the ten sheets of paper included in the supplement to make this lampshade.The paper comes with pre-inserted fold lines, so just fold the paper along those lines.Use the side with indented fold lines as the front side of the paper. The colored side ofpaper shown in the diagrams is the front side.Time to complete: 1 hr. 2 hrs. How to fold one unitHandComplete thisstep for allfive starsPocketPocket❺❶Unit completedHandHandHand3. Fold each bigtriangle in half.4. Fold only each ofthe two smalltriangles in front inhalf.2. Fold at each of the fold linesshown in the drawing to createtwo big triangles.5. Fold each in tothe oppositesides.6. Unfold the foldedsections back into the bigtriangles shown in .❷❹PocketPocket❸5. Add five more units with each unit added asshown in the diagram so as to connect eachset of two neighboring arms together of thefive arms projecting out from the star.Fold all thirty of the stripsof paper in the same way.Structural diagram for the Celes1.Line up the mountain folds andvalley folds on a hand with thoseon a pocket, and slide the handall the way into the pocket sothat they fit together smoothly.PocketHandAt first glance, the Celes appears to be fairlycomplicated, but it actually has the simple structure asshown in the diagram. First, you need to create thefirst star for the bottom, then the five stars for the firstline on top of that, and then the five stars for thesecond line on top of the first one.Finally, you just need to put together the very last starfor the top to complete the lampshade.Once you've slid ahand into apocket, go backand redo thecreases on eachagain to reinforce.The fivestarsfor thesecond line2. Insert in thesame way aswith the firstone.Thefive starsfor thefirst lineComplete thisstepfor all five stars❶❷❸❷Complete thisstepfor all five stars❸❺8. Combine two arms projecting out from onestar with those of neighboring stars ( ❶ and ❷ ,❸ and ❹ , and so on) to create five partial starassemblies. Once you've completed this step,you should have five partial star shapes with twopoints each.❹10. Add in a total of five more units, one at atime, so as to connect together neighboringstars in the five star assemblies. Once you'vecompleted this step, you should have fivepartial star shapes with four points each.The star for the topPutting together the five stars for thesecond line6. After adding in the five units, you shouldend up with five partial star shapes ( ❶ – ❺ ),each with three of the five points of acompleted star, for an overall shallow dish-likeshape. The above picture was taken from theback side of the assembled shape.❶ Putting the units togetherPutting together the starfor the bottom7. Add in two additional units (for a total of tenunits) to each of the partially formed stars asshown in the diagram to complete the five starsfor the first line.Each sheet of the paper for this lampshade includes three attached strips.Please cut the three strips apart cleanly using a utility knife or other cutting tool beforestarting the origami folds.This side isthe back sideof the paper.The fold linesare raised.1. Fold the top andbottom ends intotriangles.Putting together thefive stars for the first line9. At this point, there should be fiveunattached arms ( ❶ – ❺ ) sticking outfrom the assembly as seen from theback side. Attaching the assembledlampshade to the LED standPutting together the star for the topThe star for the bottomAttach the attachment at a place where three stars intersect.You may find it easier to insert the attachment if you cut outa hole in the unit where you plan to insert it that is bigenough to fit it into using a utility knife or other cutting tool.FinishedThe fifthunit11.Add additional units to thepartially completed stars inorder to complete each fivepointed star. The fiveunattached arms here will becombined together to formthe final star for the top of thelampshade.3. Insert the fourth and fifth units asshown in the diagram.You may find it easier to insert the fifthunit if you open the pocket up and thenrefold it so as to cover the last hand, asshown in the picture.7Otona no Kagaku4. This star shape formed using five different units is thebase structure for this lampshade.[Diagram of lampshade beforecompletion] While completingassembly of the stars for thesecond line, use the unattachedarms to put together the star forthe top of the lampshade. Thispicture shows completion ofthree of the points on the finalstar.Attachment receiverInsert the LED support column into the hole onthe attachment, and push it in up to theattachment receiver. Then, turn the supportcolumn clockwise into the base unit.8
EarthenValley fold(fold over)Mountain fold (foldunder)This lampshade was named Earthen because the pattern that emergeswhen the LED is lit up resembles earthenware. No paper is provided for thisproject, so please get six sheets of square paper such as regular origamipaper ready if you intend to try making this lampshade. We recommendedthat you use paper that is around 15 cm 15 cm (5.9 in. 5.9 in.) because it willbe easier to make with paper around that size.15.Fold half onlyback toward theother side.14.Fold in toward thecenter.Time to complete: 1 hr. . 1 hr. and 30 min. How to fold one unit3. Fold twoopposite corners intoward the center.Unit completedHand1. Fold the paper in half to insert avertical fold line.2. Fold in half the other way to insert ahorizontal fold line.4. Fold the paper inhalf in such a waythat the foldedparts are tuckedinside.HandHandUnit as seen fromthe back side. Putting the units together 6. Fold using an inside reverse fold.17.Open asshown.Unit as seen fromthe front side.Pocket 12.With the paper opened up as shownin the diagram, you can see that thereis an indentation in the center of thepaper (in the circled part).Push on this section from the back sothat it protrudes out, and then pull thepaper in along the fold lines.Make a total of six of theseunits.HandPocket5. Fold the two sheets together asshown in the diagram to insert acrease line.16.Repeat steps(12) to (15) to fold theopposite side. Insert each hand into a pocket. You can make it easier to put the unitstogether and achieve a more polishedfinished product if you apply glue tothe back side of the paper at theportions marked with a in thepicture.HandHandHandHand Attaching the assembledlampshade to the LED standHand11.Open as shown.HandHandHand7. Fold using an insidereverse fold.When the light is turned on, a complicatedpattern will emerge as shown in thepicture.13.Fold in towardthe opposite side.The center part willprotrude out as canbe seen in thepicture below.8. Do the same on the rightside.9. Fold back the overlappingsections. Do the same on theback side.9Otona no Kagaku10. Fold as shown inthe diagram. Do thesame on the backside.In the above picture, paper with a darker color on one side was used tomake it easier to tell between the front and back sides of the paper;however, in actuality, you'll achieve a better effect with the lightingusing paper that is either white or a light color on one side.Use the attachment for the Checkered Lantern. Cut away oneedge of the protrusions in the Earthen lampshade to insertthe attachment into the hole formed. Affix the Earthenlampshade and the attachment to each other usingcellophane tape or the like, and then attach the assembly tothe LED support column.Finished10
Origami paper For the Checkered Lantern: 6 sheets For the Celes: 10 sheets with 3 pre-scored strips per sheet (cleanly cut the strips apart using a utility knife or other cutting tool) * TANT N-8 paper is used for the origami paper here. * The origami paper is included in the case with the parts shown at
A11(12)(13) Assemble to Rosemount 305 Integral Manifold A12(12) Assemble to Rosemount 304 or AMF manifold with 316 SST traditional flange C11(12) Assemble to Rosemount 405C or 405P Primary Element D11(12) Assemble to Rosemount 1195 Integral Orifice and 305 Manifold EA2(12) Assemble to Rosemount 485 or 405A Annubar
A11(5) Assemble to Rosemount 305 Manifold Assemble to Rosemount 306 Manifold A12(5) Assemble to Rosemount 304 or AMF Manifold with SST Traditional Flange N/A B11(5)(6) Assemble to One Rosemount 1199 Remote Diaphragm Seal with SST transmitter flange Assemble to One Rosemount 1199 Remote Diaphragm
work/products (Beading, Candles, Carving, Food Products, Soap, Weaving, etc.) ⃝I understand that if my work contains Indigenous visual representation that it is a reflection of the Indigenous culture of my native region. ⃝To the best of my knowledge, my work/products fall within Craft Council standards and expectations with respect to
3 Truck scale debugging step introduction 1st step: set up address and assemble scale Method 1 suitable for C and E type digital load cells 1 set up address for every digital load cell FUNC 0 of 4.1 2 indicator search and assemble scale FUNC 1 of 4.2 Method 2 when use E type module which has automatic assemble net function, the
Manifold assembly “Assemble-to” items are specified separately and require a completed model number. These options are not valid with option code P9 for 4500 psi static pressure. Code Description S5 Assemble to Rosemount 305 Integral Manifold S6 Assemble to Rosemount 304 Manifold or Connection System Integral mount primary element
Integral Manifold Standard Standard Standard S3 Assemble to Rosemount 405 Compact Orifice S5(8) Assemble to Rosemount 305 Integral Manifold S6(8) Assemble to Rosemount 304 Manifold or Connection System Cleaning Expanded P2 Cleaning for Special Services Material Traceability Certification Standard Standard Standard
Primary Element or 1195 Integral Orifice Primary Element S3 Assemble to Rosemount 405C or 405P Compact Orifice Plate Seal assemblies (11) S1 (14) Assemble to one Rosemount 1199 Diaphragm Seal S2 (15) Assemble to two Rosemount 1199 Diaphragm Seals Mounting brackets B1 Tradi
HL DIN compliant traditional flange, SST, 12 mm adapter/manifold bolting 316 SST Manifold assembly(16) S5 Assemble to Rosemount 305 Integral Manifold S6 Assemble to Rosemount 304 Manifold or Connection System Integral mount primary element(15)(16) S3 Assemble to Rosemount 405 Compact Orifice Plate
