Polaris 9300xi Sport
Polaris 9300xi SportOwner's ManualManuel du propriétaireManual del usuarioWARNINGFOR YOUR SAFETY - For anything other than the routine cleaning and maintenance describedin this manual, this product must be serviced by a contractor who is licensed and qualified in poolequipment by the jurisdiction in which the product will be installed where such state or localrequirements exist. In the event no such state or local requirement exists, the maintainer must bea professional with sufficient experience in pool equipment installation and maintenance so that allof the instructions in this manual can be followed exactly. Improper installation and/or operation willvoid the warranty.AVERTISSEMENTPOUR VOTRE SÉCURITÉ – Pour toute opération autre que l’entretien de routine et la maintenancedécrite dans ce manuel, ce produit doit être pris en charge par une entreprise qui est autorisée etqualifiée pour la réparation des équipements de piscine par la juridiction où le dit produit est installélorsque de telles exigences locales ou provinciales sont édictées. Si aucune exigence locale ouprovinciale n’est disponible, l’agent d’entretien doit être un professionnel avec suffisamment d’expérience dans l’installation et la maintenance d’équipement de piscine pour appliquer correctement lesconsignes du présent manuel. L’installation ou l’utilisation inappropriée annulera la garantie.W2093A RevAADVERTENCIAPARA SU SEGURIDAD - Para cualquier cosa con excepción de la limpieza rutinaria ymantenimiento de descritos en este manual, este producto debe ser atendido por un contratista queestá autorizado y calificado en equipo de piscina bajo la jurisdicción en la que el producto se instalaen donde requisitos de estado y locales existen. En el caso de que no exista ningún requisito deestado o local, el responsable debe ser un técnico profesional con experiencia suficiente en lainstalación de piscinas y mantenimiento de equipo para que todas las instrucciones en este manualpuede ser seguidas exactamente. Inapropiada instalación y/o operación anulará la garantía.
Page 3Section 1.Important Safety Instructions .4Section 2.2.19300xi Sport Specifications.6General Specifications .6Section 3.3.13.23.3Assembly and Initial Usage.6Unpacking .6Assembling the Transport Caddy .6Connecting the Control Unitto the Caddy .8Electrical Connection .83.4Section 4.4.14.24.34.44.5Operation .9Submerging the Cleaner .9Operating the Cleaner .9Removing the Cleaner .10Remote Control Mode .10Enabling the AutomaticStart Mode .11Section 5.5.15.2Cleaning and Maintenance .11Cleaning the Filter Canister .11Cleaning and Storing theCleaner .12Replacing the Brushes .13Replacing the Tires on theCleaner .145.35.4Section 6.6.1Troubleshooting .15General Troubleshooting .15Section 7.Polaris 9300xi Sport Exploded Viewand Replacement Parts List .16Parts List .16Exploded View .177.17.2THANK YOU FOR PURCHASING THE POLARIS 9300 SPORT CLEANER.YOUR POLARIS 9300xi SPORT HAS BEEN DESIGNED AND MANUFACTURED TO BE EASILY INSTALLED ANDTO PROVIDE LOW MAINTENANCE OPERATION. PRIOR TO INSTALLING YOUR NEW POLARIS 9300xi SPORT,PLEASE DO THE FOLLOWING:1)2)3)Complete and return the warranty card.Record your purchase information on the spaces provided below.Attach your invoice (or a copy) to this page.Taking these steps will help ensure prompt warranty service, should it be required. If service is required, pleasecontact your original dealer. If the original dealer does not perform warranty service, please visitwww.polarispool.com to locate an independent service company near you. If you are unable to locate a servicecompany, please call our Technical Support department at 800-822-7933.RECORD YOUR 9300xi SPORT POOL CLEANER DATA HERE:Date of PurchasePurchased FromSerial Number:(located on machine head)CityStateZip CodeEnglishTable of Contents
Page 4Section 1.Important Safety InstructionsCongratulations on purchasing the Polaris 9300xi Sport cleaner. Please take a moment to read through the entiremanual before installing your new robotic pool cleaner. Your cleaner must be installed and operated as specified.EnglishREAD AND FOLLOW ALL INSTRUCTIONSWARNINGFailure to comply with the following warnings can result in permanent injury, electrocution ordrowning.PREVENT ELECTRICAL SHOCKTo reduce risk of electrical shock: Connect unit to receptacle protected by a ground fault circuit interrupter (GFCI). Such a GFCI receptacleshould be provided by a qualified installer and should be tested on a routine basis. To test the GFCI, push thetest button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCIfails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the testbutton being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not usethis product. Disconnect the cleaner and have the problem corrected by a qualified service representativebefore using. Per the United States National Electric Code (NEC), keep the power unit at least 5 feet from the edge ofthe (pool/spa) water and do not remove it from its caddy. In Canada, the Canadian Electrical Code (CEC)requires a minimum distance of 3 m (10 ft.) to be maintained between the pool edge and the power unit. Neversubmerge the control unit. Do not enter pool while the 9300xi Sport is in water. Do not bury cord. Locate cord so as to prevent it from being damaged by lawn mowers, hedge trimmers andother equipment. To reduce the risk of electrical shock, do not use the 9300xi Sport cleaner or control unit if the cord is worn ordamaged. Contact Zodiac Pool Systems, Inc. immediately for a replacement cord. Double insulation—For continued protection against possible electric shock, use only identical replacement partswhen servicing. Do not attempt repair of the 9300xi Sport cleaner, control unit, power cord, or floating cable. NEVER OPEN CONTROL UNIT. Do not use an extension cord to connect the unit to electric supply; provide a properly located outlet. Thecontrol unit should be placed near the outlet box.PREVENT CHILD INJURY AND DROWNING To reduce the risk of injury, do not permit children to operate this product. Do not let anyone, especially small children, sit, step, lean, or climb on any equipment installed as part ofyour pool’s operational system.
Page 5CAUTION This product is intended for use with permanently-installed pools. Do not use with storable pools. Apermanently-installed pool is constructed in or on the ground or in a building such that it cannot be readilydisassembled for storage. A storable pool is constructed so that it is capable of being readily disassembled forstorage and reassembled to its original integrity. The 9300xi Sport must be installed and operated as specified. Turn the 9300xi Sport off before removing it from water, and do not operate out of water. Do not remove the 9300xi Sport from the pool for 15 minutes after the cleaning cycle has completed. Clean filter canister in the 9300xi Sport after each use. Do not use the product in your pool if the water temperature is above 95 F (35 C) or below 55 F (13 C).CAUTIONThis device complies with part 15 of the FCC Rules. Operation is subject to the following two (2) conditions: (1) thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipmentand receiver. Connect the equipment to an electrical source on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.Modifications made to this equipment, which are not authorized by the manufacturer, may void the user’s authorityto operate this equipment.CAUTIONUSE OF THE POLARIS 9300 SPORT CLEANER IN A VINYL LINER POOLCertain vinyl liner patterns are particularly susceptible to rapid surface wear of pattern removal caused by objectscoming into contact with the vinyl surface, including pool brushes, pool toys, floats, fountains, chlorine dispensers,and automatic pool cleaners. Some vinyl liner patterns can be seriously scratched or abraded simply by rubbingthe surface with a pool brush. Ink from the pattern can also rub off during the installation process or when it comesinto contact with objects in the pool.Zodiac Pool Systems, Inc., is not responsible for, and the Limited Warranty does not cover, pattern removal,abrasion or markings on vinyl liners.SAVE THESE INSTRUCTIONSEnglishFailure to comply with the following warnings could cause damage to pool equipment or personalinjury.
Page 6Section 2. 9300xi Sport Specifications2.1 General SpecificationsThe general specifications for the Polaris 9300xi Sportare as follows:X4English9300xi SportControl box supply voltage100-125 VAC, 60 HzPolaris 9300xi supply voltage30 V DCInstalled load150 W maxCable length70 ft (21 m)Cleaner size (WxDxH)16.9 x 18.9 x 10.6 in.43 x 48 x 27 cmPack size (WxDxH)22.8 x 22.8 x 23.2 in.58 x 58 x 59 cmWeight of Cleaner25 lbs. (11.3 kg)Packed weight42 lbs. (19 kg)Filtrationless than 100 micronsCycle lengths1.30 hrs, 2.30 hrs.The Polaris 9300xi is a double-insulated product. Adouble-insulated electrical appliance is one which hasbeen designed in such a way that it does not require asafety connection to ground. The basic requirement fordouble-insulation is that no single failure can result indangerous voltage becoming exposed so that it mightcause an electric shock and that this is achieved withoutrelying on an earthed (grounded) metal casing. This isachieved by having two (2) layers of insulating materialsurrounding live parts or by using reinforced insulation.Therefore, devices having double-insulated construction, such as the Polaris 9300xi, do not utilize a grounded (three-prong) cord/plug.X1X4X2X2X1X1Figure 1.X1Polaris 9300xi Sport ComponentsTo unpack the 9300xi Sport and its components:1. Remove the lower portion of the caddy along withthe upper and lower power cable hooks, controlunit hook, power cable hook plate, locking plate,nuts, bolts and screws.2Remove the small box that contains the control unit.3.Remove the handles (left and right) of the caddy,which are located against one side of the box.4.Remove the cleaner from the box.3.2 Assembling the Transport Caddy1.Position the power cable hook and control unithook on the upper tubes as shown in Figure 2.Make sure the upper tubes (handles) are in theproper orientation.Section 3. Assembly and InitialUsage3.1 UnpackingThe packaging should contain the following items(Refer to Figure 1):9300xi Sport cleanerControl unitRemote controlTransport and storage caddy (complete withassembly components)Check that the unit has not been damaged duringtransport. If you detect damage, contact Zodiac PoolSystems, Inc. at 1-800-822-7933 before using your9300xi Sport cleaner.!12 Figure 2.Install Hooks on the Upper Handles
Page 72.Secure the power cable hook and control unit hookaround the tubes using a screw and hand tightenwith the Torx wrench (supplied with unit). Referto Figure 3.73Figure 6.Figure 3.3.Install the Power Cable Hook andControl Unit HookSecure the control unit hook using two (2) boltsand two (2) nuts and tighten with Torx wrench.Refer to Figure 4.8Figure 7.6.4Figure 4.4.Position the Bottom Power Cable HookSecure the Bottom Power Cable HookSecure the cable hook plate using two (2) bolts andtwo (2) nuts and tighten with Torx wrench. Referto Figure 8. The transport caddy is now ready touse as shown in Figure 9.9Secure the HooksInsert the upper tubes (handles) into the bottomtubes on the cart as shown in Figure 5. Makesure the upper tubes (handles) are in the properorientation and align the screw holes.Figure 8.Secure the Cable Hook PlateFigure 9.Transport and Storage Caddy Assembled5Figure 5.5.Install the HandlesPosition the bottom power cable hook as shownin Figure 6. Place the cable hook plate oppositethe power cable hook. Secure using a screw andtightening with the Torx wrench. Refer to Figure 7.English6
Page 83.3 Connecting the Control Unit to theCaddyPosition the control unit over the control unit hookon the caddy.2.Slide the locking plate clips into the control hookand line up the screw holes. Refer to Figure 10.English1.3.4 Electrical ConnectionWARNINGFailure to comply with the following warnings canresult in permanent injury, electrocution or drowning.PREVENT ELECTRICAL SHOCK U.S.: Keep the control unit at least 5 feet from the edgeof the pool. CANADA: Per CEC requirements, keepthe control unit at least 3 m (10 ft.) from the edge of thepool. Only connect the control unit to a receptacleprotected by a ground fault circuit interrupter (GFCI).Contact a certified electrician if you cannot verifythat the receptacle is protected by a GFCI. Do not use an extension cord to connect the controlunit.1 Do not allow anyone to swim while the 9300xi Sportcleaner is in the pool.Figure 10. Position the Locking Plate Clips3.Secure the locking plate using Phillips headscrews. Do not overtighten. Refer to Figure 11.For your safety and to obtain the best possibleperformance from your 9300xi Sport, connect thecleaner’s floating cable to the control unit and threadconnector until it is snug . Do not overtighten. Refer toFigure 12.IMPORTANT2 The 9300xi Sport control unit is equipped with anautomatic shut off feature to prevent overheating ifoperated in direct sunlight for an extended period oftime. The 9300xi Sport control unit is water-resistant, notwaterproof. Therefore, never submerge the controlunit.Power Supply1Figure 11. Secure the Locking PlateConnectorFloating Cable2Figure 12. Electrical Connection
Page 94.1 Submerging the Cleaner1.4.2 Operating the Cleaner1.Submerge the cleaner in the pool and remove anyair trapped inside by keeping the unit vertical.Refer to Figure 13.Plug the control unit into a GFCI protected powersource.Select either the Cycle I or Cycle II cleaningprogram on the control unit:Cycle I Program Completed in 1.5 hours Maximum coverage inminimal time1Cycle II Program Completed in 2.5 hours Intensive and completecleaning Thorough tile cleaning2.To start your 9300xi Sport cleaner, press the buttonfor "Cycle I" cleaning program. "Cycle I" cleaningis the primary cleaning cycle for inground pools.3.When the "Cycle I" program button is selected theindicator light above will illuminate. The cleanerwill start in a few seconds.Figure 13. Submerge the Cleaner Vertically2.Ensure the unit sinks to the bottom of the pool.Refer to Figure 14.2Figure 16. Start the Cleaner4.Figure 14. Cleaner on the Bottom of the Pool3.Spread out the floating cable over the pool,ensuring there are no kinks or coils in the cable.Refer to Figure 15.5.Figure 15. Spread Floating Cable Over the PoolDepending on the state of your pool it is possibleto modify the time of the cleaning cycle bypressing thebutton. Pressing thebuttonwill increase the cleaning time by 60 minutes ordecrease the cleaning time by 30 minutes. Whenthe cleaner is powered on, the Cycle and time willcorrespond to the cycle and the time that wereactive at the time it was last switched off.If you wish to stop the cleaner during a cleaningcycle, press the "Power" button. Refer to Figure 17.Figure 17. Turn Cleaner OffEnglishSection 4. Operation
Page 10IMPORTANT NOTES4.3 Removing the CleanerCAUTION To prevent damage to the 9300xi Sport, be sure toadhere to the following guidelines:English1.2.3.4.5.6.After the cleaning cycle is completed, the four (4)lights located on the control unit will flash slowlyto indicate that the cleaner may be removed fromthe pool. Disconnect the control unit cable from theelectrical outlet.Disconnect the cable from the control unit.Never lift the 9300xi Sport out of the pool by thefloating cable. Always use the handle to remove itfrom the pool. Refer to Figures 18 and 19. Coil the cable starting at the cleaner and gotoward the connection point at control unit.Remove coils or twists along the way.Store the Polaris 9300xi Sport on the caddy withthe cable coiled when not in use.12Figure 18. Remove Cleaner From Pool3Figure 19. Keep Cleaner Vertical to Drain Water The 9300xi Sport includes a safety feature thatautomatically stops the cleaner after 20 seconds, ifit is powered on, but not submerged in the water.For pools equipped with a beach area, this safetyfeature allows the cleaner to reverse, and back intothe pool when the impeller is out of the water.Use your 9300xi Sport cleaner as often as neededto keep your pool clean.Clean the filter canister after each cleaning cycle.Do not leave your cleaner in the pool on apermanent basis.At the end of each cycle, remove the cleaner fromthe pool. Start at the cleaner head and untangle anycoils in the hose before storing the cleaner.Remove the 9300xi Sport from pool when superchlorinating.4.4 Remote Control ModeCAUTIONThis device complies with part 15 of the FCC Rules.Operation is subject to the following two (2) conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may causeundesired operation.NOTE This equipment has been tested and foundto comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance withthe instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio ortelevision reception, which can be determined by turningthe equipment off and on, the user is encouraged to tryto correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipmentand receiver. Connect the equipment to an electrical sourceon a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TVtechnician for help.Modifications made to this equipment, which are notauthorized by the manufacturer, may void the user’sauthority to operate this equipment.
Page 11Remote control of the Polaris 9300xi Sport is availableusing the hand held remote control unit.The remote control unit has four (4) buttons:Rotate RightProcedure for cancelling an automatic start:1.2.Connect the control unit to the receptacle.Press the OFF button for more than six (6) seconds.3.The two (2) lights will flash onceSection 5. Cleaning and MaintenanceWARNINGRotate LeftTo avoid electric shock and other hazards whichcould result in permanent injury or death, disconnect(unplug) the cleaner from the control unit beforeperforming any cleaning and maintenance.Forward5.1 Cleaning the Filter CanisterFigure 20. Remote ControlTo turn the cleaner, you must hold down the rotate leftor rotate right button.When using the remote control unit, the two (2) lights onthe control unitwill flash alternately.To return to automatic mode, either stop using the remote control unit buttons for a minimum of 45 secondsor press Cycle I or Cycle II button on the control unit.4.5 Enabling the Automatic Start ModeThis Automatic Start Mode allows the control unit tolaunch a pre-selected cleaning cycle triggered by anexternal source (timer / programming clock).The cycle can be either "Cycle I" or "Cycle II”.The 9300xi Sport will run for 2.5 hours.It is not possible to change the running time whenoperating in this mode.The filter canister should be cleaned at the end of eachcycle.1. Ensure that the control unit cable has beendisconnected from the electrical outlet or that thefloating cable has been disconnected from thecontrol unit.2. Remove the cleaner from the water and let theremaining water drain by maintaining the cleanerin the vertical position.3. Set the unit on its wheels.4. To remove the filter from the cleaner, follow thesteps 1 through 6 (Figures 21 through 24).5. Push the cover lock (1) and lift the cover (2) untilit is secured in the vertical position. Refer toFigure 21.12Procedure for launching a cycle witha programming clock (timer):1.Connect the control unit to the receptacle.2.To automatically start the “Cycle I”, press thefollowing button for more than three (3) seconds:3. Cycle ITo automatically start the "Cycle II”, press thefollowing button for more than three (3) seconds:4.5. Cycle IIThe two (2) lights will flash onceThe robot will start automatically when it ispowered on.Figure 21. Lift Cleaner Cover6.7.8.9.Remove the filter assembly from the body (3), asshown in Figure 22.Push the quick release button on the canisterassembly (4) and pull open the filter assembly (5).Refer to Figure 23.Separate the filter canister from the filter support(6), as shown in Figure 24.Wash the filter canister, the filter support, and thecleaner under water or using a hose (7). Refer toFigure 25.EnglishReverse
Page 125.2 Cleaning and Storing the CleanerThe cleaner must be cleaned regularly using slightlysoapy clean water, do not use solvents such a trichloroethylene or its equivalent. Rinse the cleaner generouslyusing clean water. Do not let your cleaner dry in directsunlight near the pool. The cleaner must be stored on itsown caddy, so that it dries quickly.English31.Place the rear wheels on the caddy side wedges asshown in Figure 26.Figure 22. Remove Filter Assembly154Figure 26. Position Cleaner on Caddy2.Figure 23. Open Filter AssemblyRoll the unit into place onto the caddy. Refer toFigure 27.NOTE The cleaner cable must be disconnected fromthe control box before removing the cleaner fromthe pool. Wrap the cleaner cable around thehooks located at the rear of the caddy.62Figure 24. Remove Filter CanisterFigure 27. Roll Cleaner onto Place on the Caddy7Figure 25. Wash Filter Canister
Page 135.3 Replacing the Brushes4.The cleaner is fitted with PVC brushes. There are ''wear''indicators on the brushes. To maintain cleaner performance at its best you need to replace the brushes as soonas one of the wear indicators has been reached (even ifthe blade wear is not even). Zodiac Pool Systems, Inc.recommends that you replace the brushes every two (2)years.4English1.Thread each tab into the slot provided and gentlyfeed it through until the heel comes out at theother side of the slot. Refer to Figure 31.Lift the cleaner to a vertical position so that thehandle is up. Refer to Figure 28.Figure 31. Pull Tabs Through Each Slot15.Use a pair of scissors to cut the tabs 3/4 inch fromthe heel so that they are no higher than the spikesas shown in Figure 32.6.Repeat this procedure to install the second brush.Figure 28. Clean in Upright Position2.Separate the edges of the brush and undo the tabsas shown is Figure 29. Remove the worn brushes.2Figure 32. Cut TabsFigure 29. Undo the Tabs of the Brush3.To install a new brush, position the new brush onthe roller with the spikes facing downwards. Referto Figure 30.3Figure 30. Install the New Brush
Page 145.4 Replacing the Tires on the CleanerPull on the inside of the old tire to remove the tirelip from the wheel. See Figure 33.English1.4.Push one side of the tire on to the wheel and fit therib of the tire in the groove of the wheel as shownin Figure 36.21Figure 36. Start on One Side of the TireFigure 33. Pull the Old Tire Over the Wheel2.5.Remove the old tire as shown in Figure 34.Work the tire onto the wheel and verify the rib ofthe tire is positioned properly within the groove ofthe wheel. Refer to Figure 37.23Figure 34. Remove the Old Tire3.To replace the tire, position the tire on the wheelmaking sure to orient the tire so that the tread is onthe outer side of the wheel. See Figure 35.Figure 37. Work the Tire On Around the Wheel6.Push and position the rib of the inner side of thetire in the groove of the wheel. Refer to Figure 38.If needed, turn the wheel gently to help withinstallation.1!4Figure 35. Tire Replacement OrientationFigure 38. Push the Tire into Place on the Wheel
Page 15Section 6. TroubleshootingTable 1 lists some of the more common symptoms, causes and solutions encountered when using the cleaner. The unitemploys flashing lights during Cycle I and II to indicate different issues on the control unit and on the cleaner. Theseindications are not necessarily major issues. To turn off the flashing light, press the power button. Then start a new cycle:If the flashing lights persist after completing troubleshooting, please contact your retailer. DO NOT open the control unit.SymptomThe flashing indicatorlights appear just afterstart (pressing the Poweror Cycle button to start thecleaner) ( 20 seconds).CauseSolutionEnsure the floating cable is properlyplugged into the control unit.Unplug the floating cable from the control unit andplug it again properly.Ensure the cleaner is well submerged.Submerge the cleaner following the procedure inSection 4.1, "Submerging the Cleaner".Cleaner needs to be reset and startnew cycle.Press the power button OFF and then Cycle I or IIProgram buttons to start new cycle.Propeller does not turn.Please contact your local Polaris service representative.Wheels do not turn.Please contact your local Polaris service representative.The flashing lights appearsduring the cycle.If the cleaner sucks air for 60 seconds, the flashing light appears.Submerge the cleaner following the procedure inSection 4.1, "Submerging the Cleaner".The cleaner does not stayfirmly on the pool bottom.There is air in the appliance casing.Submerge the cleaner following the procedure inSection 4.1, "Submerging the Cleaner".The cleaner does not or noThe filter is full or dirty.longer climbs the pool sides.Clean the filter canister following the procedureSection 5.1, "Cleaning the Filter Canister".Sides of pool are slippery or slimy.Although the water seems clear,microscopic algae, invisible to thehuman eye, are present in the pool.As a result the pool sides becomeslippery and prevent the cleaner fromclimbing.Do a shock chlorination treatment and slightly reduce the pH. DO NOT leave the cleaner in the poolduring this treatment.Not supplied with electricity.The outlet, the control unit is connected to, is notsupplying electrical power. Check that the outletto which the control unit is connected is receivingelectricity.Unit is turned ON.Check that you have started one (1) of the two (2)programs and check that the indicator for the selected program is lit. If the problem persists, contactyour local Polaris service representative.The cycle I and II programindicators flash alternately.Your cleaner has encountered aproblem or a issue during its operation.Disconnect the control unit and wait 20 secondsbefore reconnecting the control unit. Check thatthe cable is correctly connected to the control unit.Check that no debris impedes the rotation of thebrushes and/or the propeller. Clean the filter. Starta new cleaning program. If the problem continuescontact your local Polaris service representative.The cleaner seems to beperforming less efficiently.The brushes have become smooth.Replace the brushes following the procedure inSection 5.3, "Replacing the Brushes".Filter canister is full or dirty.Clean the filter canister following the procedure inSection 5.1, "Cleaning the Filter Canister".On startup the cleaner doesnot move.Floating cable is excessively coiled or Make sure the floating cable is spread out over thekinked.pool.English6.1 General Troubleshooting
Page 16SymptomCauseThe batteries are dead and need tobe replaced.Replace the batteries in the remote control.The remote control is notsynchronized to the control unit.Synchronizing procedure:EnglishThe remote control does notwork.SolutionWhen replacing the control unit or the remote control, it is necessary to synchronise the new remotecontrol with the control unit:1.Connect the 9300xi sport to the control unit,then plug the control unit to the receptacle.2.Press OFF Cycle I buttons for morethan 6 seconds until both lightsflash once:3.Press and hold the "rotate right" button on theremote control unit.4.The light on the right will flash5 timeslights5.then bothwill flash together.The synchronization procedure is completedwhen both lights switch off.Section 7. Polaris 9300xi Sport Exploded View and Replacement Parts List7.1 Parts ListKey No. Part No.CLEANER1AR05162002AR0528600DescriptionQty.Key No. Part No.DescriptionQty.23R0518600Float Kit1CaddyControl Un
thank you for purchasing the polaris 9300 sport cleaner. your polaris 9300xi sport has been designed and manufactured to be easily installed and to provide low maintenance operation. prior to installing your new polaris 9300xi sport, please do
9300 Sport & 9400 Sport 9300xi Sport Control box supply voltage 100-125 VAC, 60 Hz 100-125 VAC, 60 Hz Supply voltage 30 V DC 30 V DC Installed load 150 W max 150 W max Cable length 60 ft (21 m) 70 ft (21 m) Cleaner size (WxDxH) 16.9 x 18.9 x 10.6 in. 43 x 48 x 27 cm 16.9 x 18.9 x 10.6 in. 43
polaris 9300 sport owner's manual. page 3 thank you for purchasing the polaris 9300 sport cleaner. your polaris 9300 sport has been designed and manufactured to be easily installed and to provide low maintenance op
The Polaris should not be used to remove plaster dust in new pools. Always remove the Polaris before swimmers enter the pool. Always handle the Polaris with care. Do not let children or pets play with the Polaris; it is not a toy. Except when checking the wheel RPM, do not h
Polaris Power For your nearest Polaris dealer, call 1-800-POLARIS or visit www.polaris.com . parts, and accessories, available through our on-line . windows are open or if ventilating fans are used to circulate air. Do not use the generator near windows, doors, vents or any other
9300.The 9300xi tear down is the same, except that some of components look different. Al ways consult the individual breakdowns for 9300 and 9300xi before replacing any part. Tools needed: 5/32” T-handle Allen wrench Rubber mallet Phillips head screw driver Disassembly: Removing
Section 2. 9300 Sport Specifications 2.1 General Specifications The general specifications for the Polaris 9300 Sport are as follows: Control box supply voltage: 100-125 VAC, 60 Hz Polaris 9300 supply voltage: 28 V DC Installed load: 150 W max Cable length: 60 feet 18 m Cleane
EU SPORT POLICY: EVOLUTION EU SPORT POLICY: EVOLUTION 2011: THE COUNCIL WORK PLAN ON SPORT On May 20, the EU Sport Ministers adopted a Work Plan for Sport. The Council Work Plan sets out the sport ministers' priorities in the field of sport for the next three years (2011-2014) and creates new working structures.
published by the American Petroleum Institute (API, 1984, 1991) are generally not consistent with the physical processes that dictate actual pile capacity. For example, the experimental observa- tion of a gradual reduction in the rate of increase of pile capacity with embedment depth is allowed for by imposing limiting values of end-bearing and shaft friction beyond some critical depth .
