TEAC DV-28S-AZ3 DVD-ROM DRIVE HARDWARE SPECIFICATION
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.CTEAC DV-28S-AZ3DVD-ROM DRIVEHARDWARE SPECIFICATIONRev. C9154c20 sheets in TotalCopyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.CTABLE OF CONTENTSTitlePage1. SCOPE . 12. OUTLINE . 13. CONSTRUCTION . 23.1 External Construction . 23.2 Installation . 44. DISC SPECIFICATION . 54.1 Applicable Disc Format . 54.2 Rotational Speed . 54.3 Data Capacity . 64.4 Readable Disc . 65. PERFORMANCE . 75.1 Operating Performance . 75.2 Acoustic Noise . 76. ENVIRONMENTAL CONDITIONS . 87. RELIABILITY . 98. SAFETY AND EMC STANDARDS . 99. FRONT INDICATOR . 910. INTERFACE CONNECTOR . 1011. POWER INTERFACE . 1112. SERIAL ATA INTERFACE . 1212.1 Outline . 1212.2 Electrical Characteristics . 1212.2.1 Serial ATA options . 1212.3 COMMAND SET . 1212.3.1 ATA COMMAND . 1212.3.2 ATAPI COMMAND . 1313. POWER MANAGEMENT SPECIFICATION . 1513.1 Power Management Modes . 1513.1.1 Transition in power management mode . 1513.2 Active Mode . 1613.3 Idle Mode . 1613.4 Standby Mode . 1713.5 Sleep Mode . 1713.5.1 Tray ejection/insertion in the sleep mode . 1714. OTHERS . 1714.1 RoHS Compliance . 1714.2 Safety of Laser Products . 18–i–Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C1. SCOPEThis is hardware specification of the TEAC DV-28S-AZ3 built-in type DVD-ROM DRIVE (hereinafterreferred to as drive). As for the software specification, refer to "DV-28S-A Software Specification".2. OUTLINEThe outline of this drive is given in Table 2-1.(Table 2-1) Outline of the specificationModel nameTEAC P/NDV-28S-AZ31977274A-Z3Applicable safety and EMC UL, c-UL, TÜV, CE, C-tick, BSMI, KCstandardsInterface transfer rateAverage access time1.5Gbps140msec (CD-ROM)/150msec (DVD-ROM), average by TEAC standardsDisc speed(24x CAV speed mode)5,160min-1 (Approx)Host interfacePower sourceSerial ATA 5VDCStarting timeCD-ROM:14sec typ (excluding the multi-session CD)DVD-ROM:15sec typ (excluding dual layers and multi-border)Readable discsCDCD-DA, CD-ROM, CD-R, CD-RWDVD DVD-ROM, DVD-R, DVD-R DL, DVD-RW, DVD R, DVD R DLDVD RW, DVD-RAMApplicable formatCDCD-DA, CD-ROM (Mode1, Mode2)CD-ROM XA Mode2 (Form1, Form2)Photo CD (Single/Multi-session), CD-i, Video-CDCD-Extra (CD-Plus), CD-TextDVD DVD-ROM, DVD-Video, DVD-R (Single/Multi-border)DVD-R DL (Single/Multi-border)DVD-RW (Single/Multi-border), DVD R (Single/Multi-session)DVD R DL (Single/Multi-session)DVD RW (Single/Multi-session), DVD-RAM (4.7GB)Front bezel colorEject button colorAccess indicatorLaser classRoHS directiveBlackBlackGreenClass 1 laser productComplies with–1–Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C3. CONSTRUCTION3.1 External Construction(1) Dimensions(a) Height: 12.7mm (excluding the front bezel)(b) Width: 128mm (excluding the front bezel)(c) Depth: 129.4mm (excluding the eject button)(2) Mass: 150g (without bezel)(3) Disc clamp system: Ball clamp(4) Loading: Manual loading using the tray(5) Ejection(a) Manual eject using the eject button(b) Automatically eject using the command(c) Eject distance: 10mm or more(6) External view: Refer to Fig. 3.1-1.–2–Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C(Fig. 3.1-1) External view of the drive–3–Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C3.2 Installation(1) Installation direction(2) Tilt(3) Installation method: Refer to Fig. 3.2-1.: Refer to Fig. 3.2-1 below.: The fixing holes in the side of the unit are used.Separate discussions and arrangements are required when theinstallation holes are not used.(a)30 or less30 or less(b)5 or less30 or less30 or less30 or less(c)30 or less30 or less30 or less5 or less30 or less 30 or less(Fig. 3.2-1) Tilt of the drive–4–Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C4. DISC SPECIFICATION4.1 Applicable Disc FormatRefer to Table 4.1-1.(Table 4.1-1) Applicable disc formatCDCD-DACD-ROM (Mode1, Mode2)CD-ROM XA Mode2 (Form1, Form2)Photo CD (Single/Multi-session)CD-iVideo-CDCD-Extra (CD-Plus)CD-TextDVDDVD-ROMDVD-VideoDVD-R (Single/Multi-border), DVD-R DL (Single/Multi-border)DVD-RW (Single/Multi-border)DVD R (Single/Multi-session), DVD R DL (Single/Multi-session)DVD RW (Single/Multi-session)DVD-RAM (4.7GB)4.2 Rotational SpeedRefer to Table 4.2-1 for the rotational speed.(Table 4.2-1) Rotational speedOperation/Disc formatRead speed/Disc speed2x CLV 2,774 - 1,150rpm2x CLV 3,246 - 1,375rpm4x CLV 1,833 - 790rpm8x CAV 4,680rpm8x CAV 4,680rpm3 - 5x ZCLV 4,869 - 3,438rpm24x CAV 5,160rpm24x CAV 5,160rpm8x CAV 4,680rpm8x CAV 4,680rpm8x CAV 4,680rpm8x CAV 4,680rpmIdle mode (DVD)Idle mode (DVD-RAM)Idle mode (CD)Read (DVD-ROM)Read (DVD-ROM DL)Read (DVD-RAM)Read (CD-ROM)Read (CD-RW)Read (DVD-R, DVD R)Read (DVD-R DL)Read (DVD R DL)Read (DVD-RW, DVD RW)–5–Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C4.3 Data Capacity 650MB/700MB 738MB/795MB 74min/79min 4.7GB/side 8.5GB/side: CD-ROM Mode1CD-ROM XA Mode2 Form1: CD-ROM XA Mode2 Form2: CD-DA: DVD-ROM, DVD-Video, DVD-R, DVD-RW, DVD-RAM, DVD R,DVD RW: DVD-ROM, DVD-Video, DVD-R, DVD R4.4 Readable DiscCD-DA, CD-ROM, CD-R, CD-RW, DVD-ROM, DVD-R, DVD-R DL, DVD-RW, DVD R, DVD R DL,DVD RW, DVD-RAM–6–Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C5. PERFORMANCE5.1 Operating Performance(1) Average random access time : 140msec average (CD-ROM, 24x), 150msec average (DVD-ROM, 8x)(2) Disc speed: Refer to Table 4.2-1.(3) Data transfer rate(a) Read sustained: 1,545 to 3,600kB/sec (CD-ROM Model)4,469 to 10,816kB/sec (DVD-ROM)(b) Programmed I/O: 16.7MB/sec max (Mode 0 to 4)(c) Multi-word DMA: 16.7MB/sec max (Mode 0 to 2)(d) Ultra DMA: 100MB/sec max (Mode 0 to 5)(4) Starting time(a) When power is switched on/when disc is loadedCD-ROM: 12sec typ (excluding the multi-session CD)DVD-ROM: 13sec typ (excluding dual layers and multi-border)(b) Return time from the standby modeCD-ROM: 4sec or lessDVD-ROM: 4sec or less(5) Data buffer capacity: 0.5MB5.2 Acoustic Noise(1) Operating(2) Ejecting(3) Others: 45dBA or less (during seek/read/write/Active/Idle, distance 0.5m): 65dBA or less (distance 0.5m): 35dBA or less (distance 0.5m)–7–Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C6. ENVIRONMENTAL CONDITIONSThe environmental conditions as specified here do not include the environmental conditions of the disc. Theenvironmental conditions of the disc should follow the specifications of the applicable disc.(1) Ambient temperature(a) During operation: 5 to 45 C (Surface temperature on the top cover and the main frame;5 to 55 C)The recording speed may be limited or reduced even in the abovetemperature due to the temperature sensitive function in the pickup.(b) During non-operation: –20 to 60 C(c) During transportation (packaged): –40 to 65 C(2) Temperature gradient(a) During operation: 11 C/hour or less (non-condensing)(b) During non-operation/transportation: 20 C/hour or less (non-condensing)(3) Relative humidity(a) During operation: 8 to 80% (non-condensing)provided that the maximum wet-bulb temperature is 29.4 C or less.(b) During non-operation/transportation: 5 to 95% (non-condensing)provided that the maximum wet-bulb temperature is 29.4 C or less.(c) During transportation (packaged): 5 to 95% (non-condensing)provided that the maximum wet-bulb temperature is 29.4 C or less.(4) Vibrations(a) During operation: When installed horizontally: 2.9m/s2 (0.3G) or lessWhen installed vertically : 1.96m/s2 (0.2G) or lessprovided that the sweep frequency is 10 to 500Hz and sweep rate,1oct/min.(b) Transportation (packaged) : 19.6m/s2 (2G) or less provided that the sweep frequency is 10 to 500Hzand sweep rate, 1oct/min.(5) Shock(a) During operation (free from malfunction): When installed horizontally: 68.6m/s2 (7G) or less (half-sine shockpulse; 11msec, intervals; 10sec)When installed vertically : 49m/s2 (5G) or less (half-sine shock pulse;11msec, intervals; 10sec)excepting CD-DA play mode.(b) During operation (while the CD-DA is playing): 19.6m/s2 (2G) or less (half-sine shock pulse; 11msec, intervals; 10sec)(c) During non-operation/transportation: 588m/s2 (60G) or less (half-sine shock pulse; 11msec)1,960m/s2 (200G) or less (half-sine shock pulse; 2msec)However, tray ejection is allowed.(6) Dust: Office environment(7) Cooling: Natural air cooling–8–Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C7. RELIABILITY(1) Mean time between failures (MTBF): 60,000 POH or more (the frequency of use should be 10% at normaltemperature and humidity)(2) Mean time to repair (MTTR) : 30 minutes(3) Loading/ejecting life: 10,000 times or more(4) Power ON/OFF life: 60,000 times or more(5) Laser diode life(a) CD: MTTF 100,000 hours (Duty 40% pulse 380mW, 85 C)(b) DVD: MTTF 31,700 hours (Duty 35% pulse 280mW, 85 C)(6) Seeking life: 2 106 times or more (random access, 25 C, duty; 20% or less)(7) Error rate(a) Read error rateDVD: Once per 1012 bits or lessCD: Mode1 and Mode2 (Form1) : Once per 1012 bits or lessMode2 (Form2) and CD-DA : Once per 109 bits or less(b) Seek error rate: Once per 106 seeks or less(8) Self-diagnosis(a) When power is switched ON: Various controllers, ROM, RAM, buffer, ECC circuit, etc.(b) When disc is inserted: Servo circuit, signal processors, etc.8. SAFETY AND EMC STANDARDSThe drive complies with the following standards.(1) Safety standardsUL, c-UL, TÜV, CE(2) EMC standardsCE, C-tick, BSMI, KC9. FRONT INDICATOR(1) Location: Refer to Fig. 3.1-1.(2) Color: Green(3) Lighting conditions(a) Continuous on During seek Transfer of the read data to the host is under way.(b) Flashing with a period of 3 second (Duty 50%) While audio is being played(c) Flashing with a period of 1 second (Duty 50%) From POR or tray loading to the end of TOC read (when the disc is present) From POR or tray loading to the end of detecting the disc (when the disc is not present). If an errorwhich is considered to arise from the disc occurs, flashing continues until the disc is ejected. If an errorwhich seems to rest with the drive’s hardware, flashing continues until the power is switched OFF.(d) Flashing with a period of 0.5 second (Duty 50%) During ejection–9–Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C10. INTERFACE CONNECTOR(1) Connector on the drive: MOLEX 47300-1040 or equivalent(2) Applicable connector on the host : MOLEX 47300-2010 or equivalent(3) Pin assignment: Refer to Table 10-1, Fig. 10-1.(Table 10-1) Interface connector pin assignmentNAMES1S2S3S4S5S6S7P1P2P3P4P5P6TYPEGNDA A GNDB B GNDDPDESCRIPTIONDifferential Signal Pair ADifferential Signal Pair BDevice Present (1KΩ Pull Down) 5VMD/DAManufacturing Diagnostic / Device AttentionGNDPin S1Pin P1(Fig. 10-1) Interface connector assignment– 10 –Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C11. POWER INTERFACEThe following specifications apply to the interface connector terminals of the drive. The power should besupplied from a power supply unit with reinforced insulation or double insulation.(1) Allowable supply voltage range: 5VDC 5% (4.75 to 5.25V)(2) Allowable ripple voltage: 100mVp-p or less, 50 to 20MHz (including the spike noise)(3) Current consumption: Refer to Table 11-1.(Table 11-1) Current consumptionModeStandby/SleepActiveRandom access (Duty 100%)During starting/seekDuring ejectAverage current max (A)49/49 (mA)0.71.0 Peak current max (A) 1.31.50.7Remarks:1. The supply voltage should be 5V 5%.2. For each of the sleep, standby, and active modes, refer to "13. POWER MANAGEMENTSPECIFICATION".3. Does not include pulse-like current below 1msec.– 11 –Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C12. SERIAL ATA INTERFACE12.1 Outline(1) Applicable standardSerial ATA International OrganizationANSI standardSFFC: Serial ATA Revision 3.0: T13/1532D (ATA-7): SFF-8020i Rev. 2.6 and INF-8090i v712.2 Electrical CharacteristicsRefer to Serial ATA Revision 3.0.12.2.1 Serial ATA options(1) Asynchrous Signal Recovery(2) Software Setting Preservation(3) Interface Power Managementdevice initiatedhost initiated(4) Spread Spectrum Clocking: yes: yes: no: no: no12.3 COMMAND SET12.3.1 ATA COMMANDRefer to Table 12.3.1-1.(Table 12.3.1-1) ATA COMMANDCODE08E590E3E100A0A1EFE6E2E0COMMANDATAPI SOFT RESETCHECK POWER MODEEXECUTE DRIVE DIAGNOSTICIDLEIDLE IMMEDIATENOPATAPI PKT.ATAPI IDENTIFY DEVICESET FEATURESLEEPSTANDBYSTANDBY IMMEDIATE– 12 –Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C12.3.2 ATAPI COMMANDRefer to Table 12.3.2-1.(Table 12.3.2-1) List of the ATAPI commands (Sheet 1 of 44424352035301BA2B5D54BB1B4E35COMMANDBLANKCLOSE TRACK/RZONE/SESSION/BORDERFORMAT UNITGET EVENT STATUS NOTIFICATIONINQUIRYMECHANISM STATUSMODE SELECTMODE SENSEPAUSE/RESUMEPLAY AUDIO (10)PLAY AUDIO (12)PLAY AUDIO MSFPLAY TRACK RELATIVE (10)PLAY TRACK RELATIVE (12)PREVENT/ALLOW MEDIUM REMOVALREAD (10)READ (12)READ BUFFER CAPACITYREAD CD/DVD CAPACITYREAD CDREAD CD MSFREAD DISC INFORMATIONREAD HEADERREAD SUB-CHANNELREAD TOC/PMA/ATIPREAD TRACK/RZONE INFORMATIONREQUEST SENSERESERVE TRACK/RZONEREZERO UNITSCANSEEKSEND CUE SHEETSEND OPC INFORMATIONSET CD-ROM SPEEDSTART/STOP UNITSTOP PLAY/SCANSYNCHRONIZE CACHE– 13 –Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C(Table 12.3.2-1) List of the ATAPI commands (Sheet 2 of 2)CODE002AAAAD23A4A3A746ACBFB6COMMANDTEST UNIT READYWRITE (10)WRITE (12)READ DVD STRUCTUREREAD FORMAT CAPACITIESREPORT KEYSEND KEYSET READ AHEADGET CONFIGURATIONGET PERFORMANCESEND DVD STRUCTURESET STREAMING– 14 –Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C13. POWER MANAGEMENT SPECIFICATIONThis drive has a power management function to reduce power consumption.13.1 Power Management ModesThe drive has the following four power management modes. The transition between these modes is performedby the timer within the drive or a command issued by the host. Active mode Idle mode Standby mode Sleep mode13.1.1 Transition in power management modeThe transition in the power management mode is shown in Fig. 13.1.1-1.POWER ON(1)SELF DIAGNOSTICNODISC PRESENCE ?(2)(3)YES(9)ACTIVEMODE(4)(5)TRAY EJECT(6)IDLEMODE(5)STANDBYMODE(10)(11)(8)TRAY LOADING(7)SLEEP MODE(12) NODISC PRESENCE ?(13)YES(Fig. 13.1.1-1) Transition in power management mode– 15 –Copyright 2013 TEAC Corporation, All rights reserved.Downloaded from Arrow.com.
HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C(1)(2)(3)(4)When the RESET signal is released, the disc detection is performed after self-diagnostics are completed.If the disc is loaded, the mode will switch to the active mode and starting operation will begin.If the disc is not loaded, the mode will switch to the standby mode.Using the power management command (IDLE, IDLE IMMEDIATE, STANDBY, STANDBYIMMEDIATE, SLEEP), the transition from the active mode to the idle, standby or sleep mode, from theidle mode to the standby or sleep mode, or from the standby mode to the idle or sleep mode is possible.(5) The transition from the active mode to the idl
DVD RW (Single/Multi-session), DVD-RAM (4.7GB) Front bezel color Black Eject button color Black Access indicator Green Laser class Class 1 laser product RoHS directive Complies with Downloaded from Arrow.com. HARDWARE SPECIFICATION, DV-28S-AZ3, Rev.C
Read DVD R, DVD RW, DVD-R, DVD-RW, CD-R and CD-RW discs Play music CDs Play VCD & DVD movies Access interactive reference materials stored on DVDs DVD functions: Read DVD-ROM, DVD R, DVD-R, DVD RW, DVD-RW, DVD R9 and DVD-R9 discs. Read DVD-RAM media CD functions: Read CD-ROM and CD-R data media, and CD-RW and CD-DA (audio) media Format .
TEAC DVD Duplicator User's Manual 1 Chapter 1. Introduction Thank you for purchasing a TEAC DVD Duplicator. The TEAC DVD Duplicator is a stand-alone disc-to-disc DVD Duplicator system that does not require connection to a computer. It can duplicate a single master DVD to DVD media at up to 16X speeds, resulting in an exact replica of a 4.7GB .
DVD RW (Single/Multi-session), DVD-RAM (4 .7 GB) Operation / Disc format Read Speed (Max.) Idle Mode (DVD/DVD-RAM) 2x CLV Idle Mode (CD) 4x CLV Read (DVD-ROM) 8x CAV Read (DVD-ROM DL) 8x CAV Read (DVD-Video) 4x CAV Read (DVD-RAM) 3x-5x ZCLV Read (CD-ROM Mode1) 24x CAV Read (Video CD) 10x CAV .
4.5 Readable Disc CD-DA, CD-ROM, CD-R, CD-RW, DVD -ROM, DVD-R, DVD-R DL, DVD -RW, DVD R, DVD R DL, DVD RW, DVD -RAM 4.6 Recordable Disc (Recording Speed) With the recommended discs, the following speeds of recording are available . (Table 4.6 -1) Recording speed CD
software. For DVD write function, this drive confirms to DVD-RW Version 1.2 / DVD RW Part 1 Volume 1 Version 1.3 / DVD RW Part 1 Volume 2 Version 1.0 / DVD-R General Version 2.1 / DVD R Version 1.3 / DVD-R9 Version 3.01 / DVD R9 Version 1.2 / DVD-RAM (4.7G)Version 2.2. For read function, it is capable to read all of the following media: DVD single
DVD-RW and DVD-R/DVD-R DL discs Recordings made on DVD-RW or DVD-R/DVD-R DL di scs cannot be played in other DVD devices or PCs unless the discs are finalized. (l64) Using with DVD player/recorder (l69) Just insert the disc into a DVD player/recorder compatible with 8 cm discs to play back the scenes recorded with this unit.
DVD movie and blu -ray - providing quick, accurate, and cost -effective solutions for . DVD to blank DVD disc in 1:1 ratio, shrink DVD9 to DVD5. without lossless quality a nd . Burn DVD to blank DVD disc with one DVD burner . Rip DVD to video / Rip DVD to portable devices: iPhone / iPod / Apple TV / Android devices FAQ . Any DVD Cloner .
Methods, Optimization in Operations Research, Advance Discrete Mathematics, Engineering Mathematics I–III, Advanced Mathematics, and the like. He is also on the editorial board and a reviewer of .
