Illuminated / Non-Illuminated Buzzer ø22mm HW1Z
ø22mm HW1ZIlluminated / Non-Illuminated Buzzer
Solution example ➀ Waterproof equipmentApplication examples Food and packaging Weigh scalesIDEC HW1Z series areA buzzer is installed to detect errors buta waterproof buzzer is required whentouched with wet hands.IP65 waterproof from the frontof the panelIdeal for equipment requiring washdown.Solution example ➁ Waterproof / DustproofApplication examples Semi-outdoor (station platform,parking lot) ElevatorsIDEC HW1Z series haveThe buzzer must be installed in a controlbox to be protected from water and dust.waterproof constructionInstalling an optional terminal rubber boot upgradesthe terminal’s waterproof characteristics to IP54without the need to use a rear enclosure.Solution example ➂ Downsizing of Equipment / PanelsApplication examples Machine tools Semiconductor Food and packagingIDEC HW1Z enablesThe depth of conventional buzzers are toolong to mount into slim panels.downsizing of panels / equipmentShort, 19.7 mm depth behind panel.Can be installed in tight places.19.7mmSolution example ➃ Safety measures in factoriesApplication examples Material handling(AGV, forklift)IDEC HW1Z haveSafety measures are required on movingequipment such as AGVs and forklifts.push-in terminalsPush-in terminals allow easy wiring.No tightening of screw is required.Solution example ➄ Locate equipment errorBuzzer sounds to alert an error but theproduction line has too many equipmentmaking it difficult to locate the placeof error.2Application examples Semiconductor Production lineIDEC HW1Z series canalert danger with sound and lightLamp and buzzer functions are integrated.Note) Illuminated buzzers only.Flashing lightBuzzer sound3
ø22mm HW1Z Illuminated / Non-Illuminated BuzzerAccessoriesShapeTerminalRubber BootMaterialPart No. (Ordering No.)Package QuantityNitryl RubberHW9Z-CZ11Installing the terminal rubber bootNotesApplicable cable: ø4.5 to 8.5 mmCut the end of rubber boot to fit the cable size(see dimensions).Weight: 10 g (approx.)6. Make sure that the bellows is 17 to 22 mm long.1. Cut the end of terminal rubber boot to fit the cable size.2. Insert the cable into the terminal rubber boot in the direction ofarrow shown below.Cut here when cable size is ø5.5 to 6.5 mmCut here when cable size is ø6.5 to 7.5 mmCut here when cable size is ø7.5 to 8.5 mmBellowsNote for terminal rubber bootCable insertion Be sure to use bellows with an appropriate length. Otherwise,waterproof characteristics cannot be achieved. Maintain a cable angle of 45 maximum to the axis of the HW1Z,otherwise the terminal rubber boot may come off.3. Strip the insulation of the cable 30 mm from the end and wire asinstructed in “Wiring”.4. Install the terminal rubber boot as shown below.5. Cover part B with part A.Part BBent excessively45 Installed(terminal rubber boot: cross section view)Part ATransformerTransformerFor 24VOperating VoltageRangePrimary Voltage100/110V ACPart No.(Ordering No.)PackageQuantityTWR5121100/110V AC 10%BuzzerHW1Z-2PQ4BHW1Z-F2PQ4B200/220V ACTWR522200/220V AC 10%1 Terminal cover (TWR-VL3) is supplied as standard. Sound and sound volume differs when used at DC voltage.Dimensions2230404852Terminal Cover404145.52,500V AC, 1 minuteM3.52 mm2 maximum, 2 wires maximum87g2Dielectric StrengthTerminal ScrewApplicable WireWeight (approx.)PRI.Damage limits: 1,000 m/s2Operating Extremes: 100 m/s22-ø3.3Mounting HolePrimary Side1Shock Resistance4Damage Limits: 30 Hz, amplitude 1.5 mmOperating extremes: 5 to 55 Hz, amplitude 0.5 mmSecondary SideJAPANVibration ResistanceAll dimensions in mm.M3.5Terminal ScrewSEC.TWR5 2100/110V AC, 200/220V AC (50/60Hz)2.4VA600V100 MΩ minimum (500V DC megger)–30 to 60 C (no freezing)–40 to 80 C (no freezing)35 to 85% RH (no condensation)3Part No.Operating VoltageCurrent DrawRated Insulation VoltageInsulation ResistanceOperating TemperatureStorage TemperatureOperating Humidity5SpecificationsBAA10004
ø22mm HW1Z Illuminated / Non-Illuminated BuzzerPart No.(Ordering No.)ShapeIllumination ColorSoundPackage QuantityIntermittent1Illuminated inated nt See website for details on approvals and standards.SpecificationsRated Current(effective value)Illuminated: 18mA (24V DC), 8mA (12V DC)Non-Illuminated(Steady sound):9mA (24V DC), 4mA (12V DC)(Intermittent sound): 7mA (24V DC), 3mA (12V DC)Inrush Current100mA maximum2,200 to 2,450HzSound TypeIntermittentIlluminated:Non-Illuminated: Steady/Intermittentø3Applicable WireSolid wire/ferrule (without sleeve): 0.2 to 1.5 mm2Ferrule (with sleeve): 0.2 to 0.75 mm2Weight (approx.)17g53)Bellows (*2)17 to 2254 to 5958 to 6362 to 6766 to 71*1: ø4.5-5.5 cable needs no cutting.*2: The bellows must be 17 to 22mm long after installing the terminal rubber boot.*3: Maintain a cable angle of 45 max. to the HW1Z axis.X2 X1X1 and X2have no polarity.Mounting Hole Layout 3.2 0.20ax.8mR0.24.1 0.40Terminal Arrangement(botom view) 00 .4Panel front: IP65 (IEC 60529)Terminal: IP40 (IEC 60529)IP54 (with terminal rubber boot) (IEC60529)Push-in Terminalsx. (*Shock ResistanceOperation extremes: 100 m/s2Damage limits: 1,000 m/s2maFlashing105 cycles/minute approx. (1.75Hz approx.)–20 to 50ºC (no freezing)20% to 85% RH (no condensation)–30 to 80ºC (no freezing)100MΩ minimum (at 500V DC megger)Between live and earthed metal parts:1000V AC, 1 minuteOperation extremes: 5 to 55Hz, amplitude 0.5mmDamage limits: 5 to 55Hz, amplitude 0.5mmTerminal StyleCut here when cable size is ø5.5 to 6.5 (*1)Cut here when cable size is ø6.5 to 7.5 (*1)Cut here when cable size is ø7.5 to 8.5 (*1)3105 cycles/minute approx. (1.75Hz approx.)Vibration ResistanceDegree of ProtectionWith terminal rubber boot45 Dielectric Strength0.517.60Sound Frequency(at 25ºC)Intermittent Cycle(at 25ºC)Illumination TypeIlluminationFlash Cycle (at 25ºC)Operating TemperatureOperating HumidityStorage TemperatureInsulation Resistance19.790dB min. at 0.1m (24VDC)70dB min. at 1m (24V DC, equivalent value)84dB min. at 0.1m (12V DC)64dB min. at 1m (12VDC, equivalent value)Panel Thickness 0.8 to 6 mm2.BuzzerRubber GasketLocking Ringø2Sound Volume(of HW1Z itself)(at 25ºC)Buzzer only330V12 to 24V DC10.8 to 26.4V DCAll dimensinos in mm.3.Rated Insulation VoltageRated VoltageVoltage RangeDimensionsø3Specifications and Ratings Panel cut-out 0.23.2 0 hole is for anti-rotation.Not required when nameplate/anti-rotationis not used.
ø22mm HW1Z Illuminated / Non-Illuminated Buzzerø22mm HW1Z Illuminated / Non-Illuminated BuzzerPart No.(Ordering No.)ShapeIllumination ColorSoundPackage QuantityIntermittent1Illuminated BuzzerRedHW1Z-P1F2PQ4R Turn off the power to the HW1Z before installation, removal, wiring,maintenance, and inspection. Failure to turn power off may causeelectrical shocks or fire hazard. For wiring, use wires of a proper gauge to meet the voltage andcurrent requirements.Panel MountingNon-Illuminated Buzzer—HW1Z-2PQ4B—Wire removal Insert the HW1Z into the panel cut-out from the front, and tighten thelocking ring from the back.Steady1HW1Z-F2PQ4BNote for panel mountingPanel Use the optional locking ring wrench (MW9Z-T1)to tighten the locking ring to a recommendedtightening torque of 1.5 to 2.0 N·m. Do not use pliers and do not tighten excessively,otherwise the HW1Z may be damaged.IntermittentLockingRingIlluminated: 18mA (24V DC), 8mA (12V DC)Non-Illuminated(Steady sound):9mA (24V DC), 4mA (12V DC)(Intermittent sound): 7mA (24V DC), 3mA (12V DC)Inrush Current100mA maximumOperating Conditions2,200 to 2,450HzSound TypeIntermittentIlluminated:Non-Illuminated: Steady/IntermittentTerminal Styleø3Applicable WireSolid wire/ferrule (without sleeve): 0.2 to 1.5 mm2Ferrule (with sleeve): 0.2 to 0.75 mm2Weight (approx.)17g5Stranded wireStrip the wire insulation 8mm from the end and pushin the wire removal part above the wire port using asmall flat screwdriver. Release the wire removal part.Make sure that the wire does not loosen.Do not use the HW1Z in the following locations. Exposure to direct sunlight Subject to corrosive or flammable gasesWire Removal Part(white)54 to 5958 to 6362 to 6766 to 71*1: ø4.5-5.5 cable needs no cutting.*2: The bellows must be 17 to 22mm long after installing the terminal rubber boot.*3: Maintain a cable angle of 45 max. to the HW1Z axis.Terminal Arrangement(botom view)X2 X1X1 and X2have no polarity.Mounting Hole Layout 3.2 0.20ax.8mR0.24.1 0.40Panel front: IP65 (IEC 60529)Terminal: IP40 (IEC 60529) IP54 (with terminal rubber boot) (IEC60529)Push-in TerminalsWith sleeveFor 0.25mm2: AI0,25-8YEFor 0.5mm2: AI0,5-8WHFor 0.75mm2: AI0,75-8GYBellows (*2)17 to 22 00 .4Shock ResistanceOperation extremes: 100 m/s2Damage limits: 1,000 m/s23)Operation extremes: 5 to 55Hz, amplitude 0.5mmDamage limits: 5 to 55Hz, amplitude 0.5mmx. (*Flashing105 cycles/minute approx. (1.75Hz approx.)–20 to 50ºC (no freezing)20% to 85% RH (no condensation)–30 to 80ºC (no freezing)100MΩ minimum (at 500V DC megger)Between live and earthed metal parts:1000V AC, 1 minute3105 cycles/minute approx. (1.75Hz approx.)Vibration ResistanceDegree of ProtectionCut here when cable size is ø5.5 to 6.5 (*1)Cut here when cable size is ø6.5 to 7.5 (*1)Cut here when cable size is ø7.5 to 8.5 (*1)maDielectric StrengthWith terminal rubber boot45 Intermittent Cycle(at 25ºC)Illumination TypeIlluminationFlash Cycle (at 25ºC)Operating TemperatureOperating HumidityStorage TemperatureInsulation Resistance0.517.60Sound Frequency(at 25ºC)Without sleeveFor 0.5mm2: A0,5-8For 0.75mm2: A0,75-8For 1.0mm2: A1-82.Buzzer19.790dB min. at 0.1m (24VDC)70dB min. at 1m (24V DC, equivalent value)84dB min. at 0.1m (12V DC)64dB min. at 1m (12VDC, equivalent value)Panel Thickness 0.8 to 6 mmø2Sound Volume(of HW1Z itself)(at 25ºC)Rubber GasketLocking RingNote for wiring3Rated Current(effective value)Buzzer only3.30V12 to 24V DC10.8 to 26.4V DCø3Rated Insulation VoltageRated VoltageVoltage RangeAll dimensinos in mm.Use a screwdriver (flat, 2.5mm-wide blade).Recommended FerrulesPhoenix ContactSolid wireStrip the wire insulation 8 mm from the end and insert into the terminal.Make sure that the wire does not loosen.Dimensions Small flat screwdriverStranded wire with ferruleClamp a ferrule with a conductor wire length of 8mm and insert intothe terminal. Make sure that the wire does not loosen.WiringSpecificationsPush in the white wire removal part above the wire ports using a smallflat screw driver, and pull out the wire. Make sure that the terminal is not constantly pulled by the wire. Wiring must be performed in environments of –5 to 50 C. Do not damage the conductor wire when stripping the wire insulation. Do not use wires with bent or deformed conductors wires. Deformed wiringmay cause faliures such as strength degradation and overheating. Connect one wire per terminal. Connecting two wires to a terminal may causeloose wiring and strength degradation. Do not solder the conductor lines. Connecting soldered stranded wires mayloose wiring and strength degradation. If a stranded wire has loose wires, twist the conductor wires beforeconnection. However be careful not to twist too much. See website for details on approvals and standards.Specifications and Ratings Prevent metal fragments and pieces of wire from dropping insidewhen installing or wiring the HW1Z. Otherwise fire, failure, ormalfunction may be caused.Operating InstructionsYellowHW1Z-P1F2PQ4YSafety Precautions Panel DEC CorporationAPEM GmbHIDEC Izumi Asia Pte. Ltd.IDEC Asia (Thailand) Co., LtdIDEC Australia Pty. Ltd.IDEC Taiwan CorporationTel: 1-408-747-0550Tel: 49-40-25 30 54 - 0Tel: 65-6746-1155Tel: 66-2-392-9765Tel: 61-3-8523-5900Tel: .comservice@tw.idec.com 0.23.2 0 hole is for anti-rotation.Not required when nameplate/anti-rotationis not used.www.idec.comHead Office6-64, Nishi-Miyahara-2-Chome, Yodogawa-ku, Osaka 532-0004, JapanSpecifications and other descriptions in this brochure are subject to change without notice.Information in this brochure is current as of August 2019.2019 IDEC Corporation, All Rights Reserved.EP1690-1Hong IDEC Izumi (H.K.) Co., Ltd.IDEC (Shanghai) CorporationIDEC (Shenzhen) CorporationIDEC (Beijing) CorporationIDEC CorporationTel: 852-2803-8989Tel: 86-21-6135-1515Tel: 86-755-8356-2977Tel: 86-10-6581-6131Tel: 22mm HW1ZIlluminated / Non-Illuminated Buzzer
Terminal Style Push-in Terminals Applicable Wire Solid wire/ferrule (without sleeve): 0.2 to 1.5 mm2 Ferrule (with sleeve): 0.2 to 0.75 mm2 Weight (approx.) 17g Shape Part No. (Ordering No.) Illumination Color Sound Package Quantity Illuminated Buzzer HW1Z-P1F2PQ4R Red Intermittent 1 H
Type 91 22mm complete seal, designed to suit pump models CM1A, CM1B, CM1C, CM1D, EM1C and EM1D. Type 91B 22mm complete seal, designed to suit pump models FM0, FM0S, FM1A, FM1AE, FM2A, FM3A and FM4A. Type 93 22mm complete seal, designed to suit pump models MR166A, MR166B and MR166E. Type 93B 22mm complete seal, designed to suit pump model
ANAESTHESIA & INTENSIVE CARE. Find our full range of products on www.vbm-medical.de . Anaesthesia System / 2 x 9mm I.D. Silicone Respiration Tubing, 22mm /10mm Cuff, 110cm long 1 x 9mm I.D. Silicone Respiration Tubing, 22mm /22mm Cuff, 110cm long .
Wiring diagram key Element Description A1 Fuel display B3 Horn B19 Reversing buzzer (*) B30 Flow divider buzzer (*) B55 Seat switch seat contact delay buzzer (*) C80 Capacitor for seat switch E6 Front left indicator (*) E7 Rear left indicator (*) E8 Front right indicator (*) E9
The Complete Illuminated Books of William Blake (Unabridged). Each work in Illuminated Printing is said to be an Illuminated Manuscript [sic] with the Original Illustrations of William Blake, and each copy is said to be a "carefully crafted ebook". The series seems to omit all Blake's "Illuminated Manuscripts" such as Tiriel and Vala or The .
Cutler-Hammer pushbuttons or 22mm mushroom pushbuttons. Replacement Keys Part Number Quantity Price Description ECX1067-2 Pkg of 2 6.25 Replacement key for GCX series key-actuated selector switches, pack of 2 sets (2 keys each). NOTE: Will not work with Cutler-Hammer 22mm switches. www.automationdirect.com Pilot Devices tPIL-19
4327-00 conduit hanger 0750 0.75 install every 2 ftinstall every 2 ft 3309-00 regulator conduit adaptor 26.7mm 7.75 install 1 / regulator 4257-00 flush breather 22mm pipe - conduit 33.25 with 18 inch standpipe 4257-6-00 flush breather 22mm pipe - conduit 38.75 with 24 inch standpipe 7601400100 s
Manual lever 5 Wire removable head DT90E1012 Digital display 1,2 or 3 On/Off Periods Frost protection 7 day programming Honeywell 22mm Zone Valve Honeywell Wired Thermostat Honeywell Programmable Thermostat Honeywell 22mm Y Plan Valve Honeywell Digital Thermostat Honeywell Wire
Cold War, focusing necessarily on the whole world, and not on regions or subregions. Perhaps only now with the post-Cold War rise of China and with Asia’s vital role in the global economy can one realistically talk about a US grand strategy significantly focused on the Indo-Pacific region. Yet ironically, just at the moment when Asia has become
