JBR Adjustable Short Shift Plate Kit Pre-Installation .
JBR Adjustable Short Shift Plate KitPre-Installation InstructionsAttaching the stand-off to the Shift Plate1. With the Shift Plate facing up, insert the male end of the stand-off throughthe slotted hole.2. Locate the stand-off in the middle of the slotted hole. Attach Using thesupplied lock washer and nut. Tighten as shown using 2 13mm wrenches.
JBR Adjustable Short Shift Plate Kit Installation Instructions2010 – 2012 MAZDASPEED 31. Engage the emergency brake and open the hood.*Note* If you have an aftermarket cold air intake, refer to manufacturesinstructions for removal if necessary.2. Remove the 2x10mm bolts from the inter-cooler cover. Slide the covertowards the back of the car and lift off.3. Unclip the MAF sensor connector by pushing down on the back of theconnector and pulling towards the back of the car. Loosen the 10mm bolt onthe hose clamp of the intake.
4. Remove the 10mm bolt and unclip the 2 hold downs for the air box cover.5. Pull the air box cover up and towards the driver's side of the car whileremoving the intake hose from the cover. Unclip the gray wire fastener fromthe top of the air box used to secure the MAF sensor wire.6. Pull/Tug up on the bottom half of the air box and remove from the car.
7. Remove the 2x12mm bolts and the factory shifter weight.8. Using a pair of needle nose pliers, slipped under the shifter cable end, thenpry up to pop the cable off the existing ball stud.
9. Place the Short Shift plate in position as shown below.*Note* The plate is meant to sit on top of the original ball stud. The ball studdoes not go through the shift plate10. Place 1 lock washer on each 8mm hex cap bolt and install with the newweight using a 6mm hex wrench.It should now look like this:
11. Now center the shifter cable you previously removed over the new ball studand press down until you here it snap in to place.12. Now re-install the factory air box assembly if necessary and inter-coolercover. See Required Factory air box modifications below.Make sure you properly connect the intake hose to the top half of the air box anddon't forget to reconnect the MAF sensor if you removed it.
ADJUSTING THE THROWAdjusting the throw of your new JBR Short Throw Shift Platekit only takes a few minutes.1. Gain access to the shift plate using the instructions above.2. Unbolt the shift plate from the counter weight and rotatethe shift plate on to its side with the shift cable stillattached.3. Using 2 13mm wrenches loosen the stand-off enough toallow it to slide to the desired position and re-tighten.4. Re-install the shift plate and counter weight.Longer ThrowShorter Throw
If You Are Using the Factory Air BoxIf you are using the factory air box, you WILL need to apply rubber grommets (notSupplied) to the pegs on the bottom of the factory air box and in the factorygrommets of the car for a total of 4 grommets. The grommets have a ½” insidediameter hole and are 1” in overall diameter. These rubber grommets shown belowcan be found at any hardware store or home center for around a dollar each. Slipthe grommets over the pegs as shown below. They are required to provide a 1/4” ofclearance in order for the Shift Plate to operate correctly.Below you will see the factory air box with the grommets attached.Below you will see how the additional grommets are to be placed in the factorygrommets of the car.
If you purchased the Stage 2 Adjustable Short Shift Plate Kit or Solid Shifter BaseBushings at another time, you can use 2 rubber bushings removed from the shifterbase in place of all 4 of the grommets shown above. Slip 1 bushing over each of thepegs on the bottom of the air box as shown below.Failure to carefully follow the installation instructions for your JBR product couldresult in damage to your car or your new parts. Please take the time to read andthoroughly understand the instructions prior to installation. The directions are asaccurate as possible and may vary slightly from model year to model year.Thanks,JamieLegal DisclaimerJAMES BARONE RACING is not responsible for the misuse, incorrect installation, orfailure of any product we sell. Under no circumstances, including but not limited tonegligence, will JAMES BARONE RACING be liable for special or consequentialdamages that result from the use or inability to use our products. JAMES BARONERACING does not assume responsibility for any damage to the user, passenger or vehicleresulting from the operation of a JAMES BARONE RACING product.PLEASE DRIVE RESPONSIBLY.
ADJUSTING THE THROW Adjusting the throw of your new JBR Short Throw Shift Plate kit only takes a few minutes. 1. Gain access to the shift plate using the instructions above. 2. Unbolt the shift plate from the counter weight and rotate the shift plate on to its side with the shift cable still attached. 3.
21 INPUT: Select a TV input source. 22 SHIFT: Press and hold this button then press buttons 0-9 to directly select TV input Shift-1 VIDEO Shift-2 N/A Shift-3 HDMI 3 Shift-4 USB Shift-5 Component Shift-6 N/A Shift-7 N/A Shift-8 HDMI 1 Shift-9 HDMI 2 Shift-0 TV Tuner Shift-ON Power Toggle
2 By the first shift Is meant the morning shift, by the second shift the afternoon or evening shift, and by the third shift the night shift. Some agreements refer to the shift beginning at midnight as the first shift, but this report classifies such work as the third shift. 3 For example, a 10-cent differential on an hourly wage of 60 cents is .
CVR Odometer and Plate Type Updates - EVR Policies . Plate Types . Plate Type . Plate Types. There are select plates that can now be issued as a new plate through EVR. Just like it works for special plates on EVR, these plate types will go through the . Centralized Plate Distribution Process. You will select the plate type during a New Plate .
SHIFT-F5. Change the window to a 3D Window SHIFT-F6. Change the window to an IPO Window SHIFT-F7. Change the window to a Buttons Window SHIFT-F8. Change the window to a Sequence Window SHIFT-F9. Change the window to an Outliner Window SHIFT-F10. Change the window to an Image Window SHIFT-F11. Change the window to a Text Window SHIFT-F12.
Mitsubishi Diamana S 60 Regular 60 Mid Mid Stiff 61 Mid Mid DRIVER SPECS STOCK GRAPHITE SHAFT Loft Length Lie Left-hand 9 (Adjustable) 45.5" Adjustable Yes 10.5 (Adjustable) 45.5" Adjustable Yes 12 (Adjustable) 45.5" Adjustable Yes Model Flex Weight (grams) Torque Kick Point Fujiku
- MANUAL DEL USUARIO - MANUAL DO UTILIZADOR . PlayStation 3 - PlayStation 4 - Xbox One - PC . User Manual . TECHNICAL FEATURES A Removable gear shift knob (not installed by default) B: Stick : C: Adjustable "H-pattern (7 1)" shift plate (installed by default) D . Adjustable "Sequential ( /-)" shift plate
THE CompLETE pARTS REFEREnCE 5 TABLE S-4 the LEGO plates (continued) LABEL NAME COLOR J plate 2x4 orange, black K plate 2x6 dark azure L plate 2x8 dark grey m plate 2x12 grey n plate 4x4 black o plate 6x10 black p plate 4x4 corner round black Q plate 4x4 round grey R wing 4x4 black S wing 3x8 right black T wing 3x8 left black h
Software development is a source of security vulnerabilities. Software-developing organizations therefore need to pay at-tention to security and apply secure development practices. However, managing software development is a challenge in itself even without the added complexity of security work. Agile methodologies like Scrum are commonly .
