INSTALL & OPERATION MANUAL WiFi DMX TOUCH PANEL CONTROLLERS - OceanLED

2019I N S TA L L & O P E R AT I O N M A N U A LWiFi DMX TO U C H PA N ELCONT R O LLER SL I G H T. Y E A R S A H E A D .OceanLED INSTALL MANUAL / CONTROLLERS / WiFi DMX Touch Panel / 260319 / v9.1W W W. O C E A N L E D . C O M

CONTROLLER KIT S2 0 1 9 I N S TA L L & O P E R AT I O N M A N U A LPrefaceREAD AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL!WARNINGSBefore installing your DMX Controller, read and follow all warning noticesand instructions which are included. Failure to follow safety warnings andinstructions can result in property damage, severe injury or even death.Before installing your DMX Controller, check local laws for restrictions regardingthe use of coloured lights in your area.Salt is an inherently corrosive material. Natural and man-made surfaces aresusceptible to corrosion and deterioration when used in and around salt water.Some combinations of plastic and polymer products are impervious to salt watercorrosion, however, screws and fasteners used for the installation must be of amarine grade type stainless steel or equivalent and monitored annually to ensurethe controller remains in service for years to come.Never Use Solvents! Cleaners, fuel, and other products that may contain strongsolvents, such as acetone, that attack many plastics greatly reducing theirstrength and can cause irreversible damage.DANGERRISK OF ELECTRIC SHOCK OR ELECTRICUTIONThis unit must be installed by a licensed or certified electrician in accordancewith all applicable local codes and ordinances. Improper installation will createan electrical hazard which could result in death or serious injury to installers, orothers due to electrical shock, and may also cause damage to property. Alwaysdisconnect the power to the light at the circuit breaker before servicing thelight. Failure to do so could result in death or serious injury to serviceman, orothers due to electrical shock.2

CONTROLLERS WiFi DMX2 0 1 9 I N S TA L L & O P E R AT I O N M A N U A BLESHOOTINGPRETESTAlways test the system prior to installation. Failure to do this may result inadditional installation time and could invalidate the warranty.IMPORTANT NOTICEAttention Installer: This manual contains important information about theinstallation, operation and safe use of this product. This information should begiven to the owner and/ or operator of this equipment.WARRANTY COVERAGE2 year warranty from time of purchase, regardless of installation date.Please refer to www.oceanled.com/downloads for full warranty statement.3

CONTROLLER KIT S2 0 1 9 I N S TA L L & O P E R AT I O N M A N U A L1!OverviewUnits are not waterproof. You must mount in a dry location. When installing, besure that the controller fits the area and secures to the mounting location usingthe appropriate hardware before installing.1.1 TOOLSAND MATERIALSNever use power tools. Hand tighten only!! Drill& Drill Bits. Screw Driver, Phillips #2 Wire Strippers. Tape measure and Ruler or Straight Edge. Marking Utensil (Pencil, Sharpie Magic Marker, etc)1.2 FINDINGTHE MOUNTING LOCATION Ensure that the ambient temperature where the unit is mounted cannot exceed45 degrees C - Note that engine rooms can easily exceed this. The chosen location requires access to mains power, space for the routing of theDMX cable to the driver boxes, and also an Ethernet connection to a WiFi router /LAN WiFi for the WiFi controller if the WiFi function is required.For DC power installations please contact OceanLED for advice1.3 SPECIFICATIONS Ready to use (pre-loaded with scenes). 14 buttons, 1 fader, 28 leds (touch-sensitive keypad). Micro SD Card Up to 200 dynamic or static scenes 6-9V DC / 100-240V AC (With Adapter) Environment IP20, Temp -10 C to 50 C Certifications: EC, EMC, ROHS, ETL, UL (some in progress)4

CONTROLLER KIT S2 0 1 9 I N S TA L L & O P E R AT I O N M A N U A L2Installation2.1 CONNECTTHE WIRES (EXPLORE SERIES)1. Connect the control cable to the green connector (as below) DMX Ground Black DMX - Brown DMX Yellow Red wire (Unused, do not connect)2. Connect power via the AC/DC adapter provided. Power DC Black/White Stripe Power DC - BlackPOWERDC POWERGroundDMXGroundDMX DMX 2.2 CONNECTTHE WIRES (PRO SERIES)1. Connect the DMX cable to the green connector (as below) DMX Ground Brown Brown/White DMX - Orange DMX Orange/White2. Connect power via the AC/DC adapter provided. Power DC Black/White Stripe Power DC - Black5

CONTROLLER KIT S2 0 1 9 I N S TA L L & O P E R AT I O N M A N U A LInstallationPOWERDC POWERGroundDMXGroundDMX DMX 2.3 MOUNTIN A DRY LOCATION1. Plug the green connector block into the rear of the DMX WiFi Touch PanelController.2. For WiFi plug the local ethernet cable into the rear of the DMX WiFi touch panelcontroller3. Mount the back plate of the interface on the preferred dry mounting location.4. Close the unit by clipping the front panel onto the back plate.6

CONTROLLER KIT S2 0 1 9 I N S TA L L & O P E R AT I O N M A N U A LInstallation2.4 FINALISEYOUR INSTALLATION (EXPLORE E6)Always test the system BEFORE the boat goes back into the water. TypicalOceanLED light installs require the boat to be hauled out of the water toreplace light units.The DMX standard recommends a maximum of 32 devices to be connected inone chain. If installation requires more lights than this, please contact OceanLEDfor advice.1. If WiFi is required connect Ethernet cable from back of controller panel into asuitable WiFi router or WiFi enabled network. (The controller is DHCP enabled asstandard so should be detected by the network once powered).Installation2. ConnectExamplethe controlACcableto the control(Exploreinput of theSeries)first Explore E6 light. Thenconnect a control link cable to the next, and so on up to the last ight in the chain.3. Fit the supplied terminator to the output of the last E6 light. See the followingexample of the connections:AC POWEREthernet CablePSURouter(For WiFi DMX)Control Cable110/220V ACAC POWER KITControl Link Cable110/220V ACAC POWER KITControl Link Cable110/220V ACAC POWER KITControl Link Cable110/220V ACAC POWER KITTERMINATORKIT7

CONTROLLER KIT S2 0 1 9 I N S TA L L & O P E R AT I O N M A N U A LInstallation2.5 FINALISEYOUR INSTALLATION (PRO SERIES)Always test the system BEFORE the boat goes back into the water. TypicalOceanLED light installs require the boat to be hauled out of the water toreplace light units.The DMX standard recommends a maximum of 32 devices to be connected inone chain. If installation requires more lights than this, please contact OceanLEDfor advice.1. If WiFi is required connect Ethernet cable from back of controller panel into asuitable WiFi router or WiFi enabled network. (The controller is DHCP enabled asstandard so should be detected by the network once powered).2. Connect the DMX controller DMX output cable to the DMX input of the first driverbox. The DMX output of this box should be connected to the input of the next,and so on up to the last driver in the chain.3. Fit the suppliedterminatorto the output(Proof theSeries)last driver box. See the followingExampleInstallationexample of the DMX connections:12/24V DCPOWER INEthernet CableDRIVERDMX INDMX OUT110/220V ACPOWER INDRIVERDMX INDMX OUT110/220V ACPOWER INDRIVERDMX INDMX OUT110/220V ACPOWER INDRIVERDMX INTERMINATOR110/220V AC8POWER INDMX OUTRouter(For WiFi DMX)

CONTROLLER KIT S2 0 1 9 I N S TA L L & O P E R AT I O N M A N U A L3Operation3.1 POWER/ SCENE SELECTION1. Power on the unit by touching the top centre button.2. Select the required scene by first touching the left / right arrows under the“ABCD” display to select the ‘Area page’ if required, then touch the requiredscene button. The blue led displays the selected scene.3. Brightness / Speed / and colour of the selected scenecan be changed via the select button in the bottom rightPOWER ON/OFFSCENESELECTION3.2 PRESELECTBUTTONPROGRAMMED SCENES - EXPLORE E6Explore E6 Dual White / BlueAreaFunction1WhiteA2Blue3Blue-White1Pulse between Blue & White2Blue Pulse3White Pulse4Blue / White Pulse1Blue Strobe2White Strobe3Blue/White StrobeBCFunctionStyleSolidColoursPulse ModesStrobe Modes9

CONTROLLER KIT S2 0 1 9 I N S TA L L & O P E R AT I O N M A N U A LOperationExplore E6 / Pro Series ow4Green5Blue6Indigo7Violet8White1Blue Shade 12Blue Shade 23Blue Shade 34Blue Shade 45White Shade 16White Shade 27White Shade 38White Shade 41Green Shade 12Green Shade 23Green Shade 34Green Shade 45Red Shade 16Red Shade 27Red Shade 38Red Shade 41Red, Green, Blue Cycle2Red, Green, Blue Cycle with 40% white3Red, Green, Blue Pulse / Cycle4Red, Green, Blue, White Pulse / Cycle5White / Blue Strobe6Red, Green, Blue, White - Blue rapid Strobe7Blue / White Strobe8Green, Blue, and White Strobe1Red, Green, Blue Strobe2Red, Green, Blue, White increment3Blue / White rapid switch4Yellow / Cyan / Blue Switch5White Pulse6Red / Blue Pulse, White Fade Rapid7Green / White Strobe8Green PulseStyleRainbowColoursBlue / WhiteShadesGreen / RedShadesCycle / StrobeModesCycle / StrobeModes

CONTROLLER KIT S2 0 1 9 I N S TA L L & O P E R AT I O N M A N U A L4TroubleshootingWiFi DMX Touch Panel ControllerProblemCheckCauseFixDMX controller doesnot power onCheck Power toController is onNo PowerConnect PowerPower OKCheck ConnectionsConnected incorrectlyCorrect ConnectionsConnected OKContact WarrantyDepartmentCheck DMXconnection is daisychained betweencontroller and alldriversNot connectedcorrectlyCorrect cablingconnectionsCheck all othercables are connectedcorrectly and are notdamagedNot connectedcorrectlyCorrect connectionsDamaged cableReplace CableTerminator not fittedFit terminatorTerminator fittedContact WarrantyDepartmentCheck Ethernet cableis connected into backof controller panelcorrectly.Not connectedReconnect cableCheck the controllerpanel is recognisedon the connectednetwork.Controller not visibleTry re-bootingnetwork hub andcontroller panel.Check connectednetwork WiFi isfunctioning correctlyWiFi not functioningResolve issue withnetwork WiFiWiFi network OKContact WarrantyDepartmentCheck Connections tocontroller faceplateLights do not respondto controller and / orrandom flickering oflights / coloursCheck Terminator isfitted to last driver boxWiFi not working (onlyapplicable to wi-fimodel)11

CONTROLLER KIT S2 0 1 9 I N S TA L L & O P E R AT I O N M A N U A LWarrantyPlease remove this page and keep for your filesFor technical assistance:Europe: service@oceanled.comThe Americas: warranty@oceanledusa.comWarranty Serial Code(s): 2019 Ocean LED Marine LTDAll Rights ReservedSpecifications are subject tochange without notice.Trademarks are the property ofOcean LED Marine LTD12Ocean LED Marine LTDUnit 1 Jacknell RoadDodwells Bridge Industrial EstateHinckley,Leicestershire LE10 3BSUnited KingdomOcean LED USA LLC778 South Military TrailDeerfield BeachFloridaFL 33442-3025USATel: 44 (0) 1455 637505Fax: 44 (0) 1455 238553sales@oceanled.comTel: 1 954.523.2250Fax: 1 954.523.2249sales@oceanledusa.comwww.oceanled.com

Before installing your DMX Controller, read and follow all warning notices and instructions which are included. Failure to follow safety warnings and . 7 Green / White Strobe 8 Green Pulse Operation 2019 INSTALL & OPERATION MANUAL CONTROLLER KITS 10. WiFi DMX Touch Panel Controller Problem Check Cause Fix DMX controller does not power on