Instruction Manual - Steam Vapor Cleaning Systems
i300Professional Iron SystemInstruction Manual
USER INSTRUCTIONS i300Thank you for purchasing the Reliable i300 series iron system. Pleasefollow the instructions carefully. With proper care and maintenance, yoursteamer will provide years of dependable service.1.2.3.4.5.6.7.8.9.10.11.12.Remove the ironing station from its packing and make sure all packingparts have been taken off (including the protection bags). Lay thestation on a flat and steady surface fitted to support it next to a wallsocket (max. mt. 1,5).It is recommended to lay the iron on the supplied pad.Insert in the right seat (2) the small supplied wand to hold the hose upand hook it with the spring up to the iron-boiler connecting wire.Unscrew the safety cap (1) and let the internal air out. Fill the boilerwith: Max. 1.1 litres of water for model i300Use the funnel supplied, making sure you do not overfill the tank.Insert the plug into the main supply point; switch on boiler (4) and ironbutton (3). If the two buttons come on, iron and boiler are working.Turn the iron plate’s temperature regulating knob (6) to the position“cotton ” (indicated on the iron knob).Wait that the boiler button’s red light (4) goes off (it takes about 10minutes). While ironing, the boiler button’s red light normally comes on.The machine is ready for use.Push the steam button (7).It is possible to regulate the quantity of steam by the steam knob (8).In case the steam stops during ironing and the water button’s red light(5) comes on, it means that there is not enough water in the tank. Tostart ironing again, switch off the boiler button (4); press the steam ironbutton (7) to ensure there is no more steam in the boiler, slowly openthe pressure cap (1) and refill to the required level with warm water.Replace the cap and wait for it to build up pressure again.When you first press the steam button (after having turned the boileron and depressed the steam button on the iron) you might notice adecrease in pressure. This is because the tank has air in it. In order tohave plenty of steam (after you have depressed the iron) wait until thepressure goes back up to the maximum level before you begin.
COMPONENTS:1.2.3.4.5.6.7.Safety capWand to hold mono-hose upIron buttonBoiler buttonLight for low waterTemperature regulating knobSteam button
CAUTION Do not leave the machine unattended while the plug is connected tothe socket.The iron reaches very high temperatures and it keeps being very hoteven 15 minutes after it’s been switching off. Be careful not to burnyourself.For complete safety, before filling the boiler, please disconnect theplug.While using the machine, never unscrew or remove the cap whileunder pressure (1). Before removing it, make sure that it does notgive off steam anymore by shutting the boiler off, and pressing thesteam iron button (7) to release all remaining steam.The machine has a special heating element. Only qualifiedtechnician should replace it.The safety cap (1) must be replaced with original parts only.TECHNICAL DATAAdjustable iron thermostat set from 60 C to 215 CBimetallic safety iron thermostat with manual reset at 275 CFull aluminium-plated heating element at 800W – 120VBoiler power i300: 700WWorking pressure i300: 2,5 barTank nominal capacity of model i300: 1.4 litresTROUBLESHOOTINGPROBLEMDoessteam goout fromthe boiler?EXPLANATIONIt may happen that, while filling thetank, some water overfills the cap andflows inside the boiler wetting theinsulating materialSOLUTIONIn order to solve the problem, we suggestusing the machine as usual so that theinsulating material dries up in about onehour through the heat of the machine. Incase you still have this problem after oneworking hour, please contact the servicecentre.Does the1) While filling the tank you may have 1) The problem will go on until the excesssteam iron poured too much water into it.water is emptied. Keep the steam buttonleak steamdepressed until the water in the tank is atmixed withthe correct level.water?2) The iron plate has to be hot before 2) Please check that the temperature knobthe steam passageis on the right position: “cotton )”
There is1) The steam knob (where supplied)no steammight be closedcoming outof the2) The iron switch might be offiron?Does theironingboard getwet?1) Open the steam knob anticlockwise.2) After the iron switch comes on, wait for 4minutes so that the iron plate gets hot.3) The boiler switch might be off3) After the boiler switch comes on, wait for10 minutes so the boiler produces steam.4) The water might be used up.1) The ironing board cover might notbe able to absorb the steamcompletely4) Fill it following the instructions carefully.1) You might use a thicker cover (or twocovers) so to create a thicker surface toabsorb the steam better. In case you areusing a vacuum table, switch on thevacuum function each time you are usingthe steam2) See # 22) The steam iron leaks steam mixedwith water (Check by spraying somesteam on a dry cloth)Does theSome dirty might have gone into the Fill the empty tank with 1 liter of water,steam leak tank with the water and it is given off screw the cap up, shake it, unscrew thedirtyfrom the iron.cap and empty the tank. Repeat the actionwater?until the water is cleaned. We do notrecommend the use of any additive to pourin the tank. Before ironing again spraysome steam on a cloth until clean steamcomes out.
SPARE PARTS LIST i300ITEM D FOR HEATING ELEMENT FOR IRONING BOARDNUT FOR WAND HOLDERWASHER FOR WAND HOLDERWAND SUPPORTBOILERCOPPER HEATING ELEMENT V120 W700TEFLON O-RING FOR THE HEATING ELEMENTPRESSURE SWITCH SET 2,5 BAR MANUAL RESETFAIRLEAD FOR CAP CONNECTIONFAIRLEAD FOR MONOHOSEBULB THERMOSTAT 165 SCREW FOR BULB THERMOSTATBIPOLAR SWITCHINDICATOR LIGHTTERMINAL BLOCK PA21 4 POLESNYLON MONOHOSE MT.2,2CABLE BLOCK 6N3-4PAD RB2000SAFETY CAP 3/8 MALEO-RING FOR CAP IN TEFLONDYN SMALL FOOTWAND FOR MONO-HOSESPRING FOR CORD SUPPORTCLIP FOR SPRINGFUNNELMUSHROOM-SHAPED CAP FOR IRON RESTHOSE CLAMP CLIP 9/11GLASS WOLL INSULATINGWIRING 16 AWGCLIP FOR STOPPING MONOHOSELOWER CHASSISUPPER CHASSIS PS21CANADABRACKET TO FIX TANK PS21CANADASOLENOID VALVE S/6000/3 120VOLT UL WITH COILCOPPER TUBE FOR PRESSURECURRENT CORD 110VOLTBRASS NICHEL ANGLE 111111
ITEM GV028/52RIC003DESCRIPTIONIRON PLATEADJUSTABLE THERMOSTATTHERMOSTAT 271 MANUAL RESETCORK HANDLEBRACKET FOR STEAM IRONCAP FOR STEAM IRONWIRING FOR STEAM IRONINSERT FPR HANDLE 121 MM.FIXING SCREW M4*22BACK HANDLE SCREWCLOSING SCREWMICROHOLDER SCREWHANDLE FIXING SCREW M5X10 ZNBBLOCKING TERMINAL BLOCK SCREWHANDLE COVER FOR IRONSILK SCREEN PRINTING BACK HANDLEBUTTONHOLDERBUTTONCOVERBUTTONLOWER BUTTONBRACKETCOVER CREWCOVER CAPBRASS WAHSER-SPACERBRASS SPACERMICRONHANDLETIGHTING SCREWWASHER UNDER HANDLEWASHERUNDER KNOBFAIRLEAD FOR CURRENT CORDNUT 4MA 5588 ZNBWASHER FOR FEET"L" JOINT FOR SOLENOID WITH OGIVA"L" JOINT FOR MONOMTER WITH OGIVAFRONT SCREWTERMINAL BLOCK 4 POLESQ.TY111111111321231111111111222142113311101
i300 PARTS DRAWING
i300 WIRING DIAGRAM
WATER LEVEL STICK
www.reliablecorporation.com
9. Push the steam button (7). 10. It is possible to regulate the quantity of steam by the steam knob (8). 11. In case the steam stops during ironing and the water button's red light (5) comes on, it means that there is not enough water in the tank. To start ironing again, switch off the boiler button (4); press the steam iron
17 Table 3. Compressed Water and Superheated Steam (continued) 0.01 MPa (ts 45.806 C) 0.02 MPa (t s 60.058 C) 0.03 MPa (t s 69.095 C) v ρh s t, C v h s t, C v ρ h s 26 446. 0.037 814 3076.7 9.2827 300 13 220. 0.075 645 3076.5 8.9625 300 8811.0 0.113 49 File Size: 630KBPage Count: 60Explore furtherCalculator: Superheated Steam Table TLV - A Steam .www.tlv.comSuperheated Steam Tables - Gilson Enggilsoneng.comCalculator: Superheated Steam Table TLV - A Steam .www.tlv.comCalculator: Superheated Steam Table TLV - A Steam .www.tlv.comSteam Table Calculator Superheated Steam Region Spirax .www.spiraxsarco.comRecommended to you b
With the steam cleaner, I don't have to worry. * When thoroughly cleaning with the Kärcher Steam Cleaner 99.99% of all common household bacteria will be killed on common household hard surfaces. ** Thorough cleaning with the Kärcher steam cleaner achieves a higher cleaning performance than manual cleaning with a mop and cleaning agent.
Page 2 June 2015 Large Steam Power Plants Siemens Steam Turbines for coal-fired Steam Power Plants Power output 120 MW to 700 MW Max. steam parameters Main steam / Hot reheat steam 177 bar / 600 ºC / 620 ºC 2,570 psi / 1,110 ºF / 1,150 ºF SST-5000 series for coal-fired Steam Power Plants
2. Use the steam control to select the amount of steam you want ( m low, l medium, h high). 3.2. Squeeze the steam button to produce steam, release it to stop. NOTE: When you first start your steam station and pull the trigger for steam ironing, there will be a delay as your steam station pumps water from the reservoir to prime the system.
Superheated steam. Properties of steam Steam tables To determine various steam properties . Guide C, Section 4, or IOP Guide Total enthalpy, h g h f (sensible) h fg (latent) Extract from superheated steam tables Extract from the saturated steam tables Do you know how to use these steam tables? (Source: www.spiraxsarco.com .
To sanitize an area of your floor, leave the Steam Mop over the area for a minimum 15 seconds, but no longer than 20 seconds. ! When the Steam Cleaner stops emitting steam, simply unplug the Cleaner, remove the Water Tank, refill, and continue cleaning. Note: During first use, it may take several seconds for the Steam Cleaner to produce steam.
For two hundred years, steam power has fueled progress. Since 1903, Vapor Power International has been an industry leading innovator in the boiler and steam generation industry. With over a century of experience generating steam and heat for the most demanding applications, Vapor Power has a deep knowledge of steam requirements, which
Engineering Mathematics – I, Reena Garg, Khanna Book Publishing . AICTE Recommended Books for Undergraduate Degree Courses as per Model Curriculum 2018 AICTE Suggested Books in Engineering & Technology w.e.f. 2018-19 BSC103 – Mathematics – II 1. Advanced Engineering Mathematics, Chandrika Prasad & Reena Garg, Khanna Book Publishing 2. Higher Engineering Mathematics, Ramana B.V., Tata .
