Geetel Internet Dsl Handbook
GEETEL INTERNET DSL HANDBOOK www.geetel.net Geetel Technical Support Mon – Fri 8:00 AM – 4:00 PM 765-258-3111 or 877-994-8355 support@geetel.net Geetel Has 6 Different DSL modems IP address of the modems should be 192.168.1.1 or 192.168.3.1 Username: support Password: support NOTE: NEVER hold reset button in on the modem for more than 3 seconds unless instructed to do so by Geetel tech support. Best practice is to unplug power from modem, wait 30 seconds, then plug power back in. Follow guide below for light representation. DSL Modem 1
If your Geetel DSL modem is a gray or black Zhone or Paradyne 6381 series modem/router, the lights across the front of the modem are as follows: POWER: This is the power light. It will remain solid telling you the power is on. STATUS: This is your DSL sync system light. It is solid green when your DSL modem is talking with our DSL equipment. ACTIVITY: Light will flash on initial boot up. The light represents your DSL modem handshaking with our DSL equipment. Once communication has been established between the two devices, the light will go out and the STATUS light will become solid. LAN: The light represents your equipment. Light may be solid, but more than likely will flash as network traffic comes through modem. USB: Light is not used DO NOT HOLD IN RESET BUTTON ON DSL MODEM UNLESS SPECIFIED BY GEETEL SUPPORT
DSL Modem 2 If your Geetel DSL modem is a black ZyXEL P-660HN-51 wireless modem/router: The lights across the front of the modem are as follows:
POWER: This is the power light. It will flash for the first 30 seconds and then become a solid green light. ETHERNET: The 4 lights represent your equipment. There are 4 yellow ports (Ethernet 1 – 2 – 3 - 4) on the back of the modem where you can plug your equipment in using Ethernet cables. Lights may be solid, but more than likely will flash as network traffic comes through modem. DSL: This is your DSL sync system light. The light will flash at first and eventually become a solid green light when your DSL modem is talking with our DSL equipment. INTERNET: Light will become a solid green light after the DSL light is a solid green light. The light will be a solid green light once modem receives an IP address from Geetel giving the modem an internet connection. WLAN-WPS: Light will be solid green when wireless is enabled on the modem. By default the modem will have this feature turned off. If you are using this wireless feature and the lights are out, hold button in for 5 seconds and wireless will enable. If you want wireless turned on this modem please call the support line 258-4357. DO NOT HOLD IN RESET BUTTON ON DSL MODEM UNLESS SPECIFIED BY GEETEL SUPPORT
DSL Modem 3 If your Geetel DSL modem is a white Comtrend AR-5381u wireless modem/router combination, the lights across the front of the modem are as follows: POWER: This is the power light. It will remain solid telling you the power is on. LAN 1X, 2X, 3X, 4X: The 4 lights represent your equipment. There are 4 yellow ports on the back of the modem where you can plug your equipment in using Ethernet cables. Lights may be solid, but more than likely will flash as network traffic comes through modem.
WLAN: Light will be solid green when wireless is enabled on the modem. By default the modem will have this feature turned on. Unless we have personalized the WiFi settings for the customer, the default SSID will be Geetel plus the last 4 characters of the modem’s MAC address and the password will be the 12 character MAC address found on the bottom of the modem. The password is case sensitive, lower case letters and numbers will be used. If you are using this wireless feature and the WiFi light is not on, use a paperclip and push WiFi on/off button on front of modem for 5 seconds and wireless will enable. If you want wireless turned on for this modem please call the support line 765-258-3111 for us to personalize it for you or use the default SSID/Password settings described above after enabling WiFi on the modem. WPS: Wireless communication standard for connecting wireless equipment in your home. There is a paperclip WPS button on the front of the modem that allows you to use this WPS feature. Usually takes some past experience to get WPS to work correctly. ADSL: This is your DSL sync system light. The light will flash at first and eventually become a solid green light when your DSL modem is talking with our DSL equipment. INTERNET: Light will become a solid green light after the ADSL light is a solid green light. Light becomes a solid green light once modem receives an IP address from Geetel giving the modem an internet connection. DO NOT HOLD IN RESET BUTTON ON DSL MODEM UNLESS SPECIFIED BY GEETEL SUPPORT
DSL Modem 4 If your Geetel DSL modem is a black Comtrend AR-5381u wireless modem/router combination, the lights across the front of the modem are as follows: POWER: This is the power light. It will remain solid telling you the power is on.
ETH 1, 2, 3, 4: The 4 lights represent your equipment. There are 4 yellow ports on the back of the modem where you can plug your equipment in using Ethernet cables. Lights may be solid, but more than likely will flash as network traffic comes through modem. WiFi: Light will be solid green when wireless is enabled on the modem. By default the modem will have this feature turned on. Unless we have personalized the WiFi settings for the customer, the default SSID will be Geetel plus the last 4 characters of the modem’s MAC address and the password will be the 12 character MAC address found on the bottom of the modem. The password is case sensitive, lower case letters and numbers will be used. If you are using this wireless feature and the WiFi light is not on, push WiFi on/off button on front of modem for 5 seconds and wireless will enable. If you want wireless turned on for this modem please call the support line 765-258-3111 for us to personalize it for you or use the default SSID/Password settings described above after enabling WiFi on the modem. WPS: Wireless communication standard for connecting wireless equipment in your home. There is a WPS button on the front of the modem that allows you to use this WPS feature. Usually takes some past experience to get WPS to work correctly. DSL: This is your DSL sync system light. The light will flash at first and eventually become a solid green light when your DSL modem is talking with our DSL equipment. INTERNET: Light will become a solid green light after the ADSL light is a solid green light. Light becomes a solid green light once modem receives an IP address from Geetel giving the modem an internet connection. DO NOT HOLD IN RESET BUTTON ON DSL MODEM UNLESS SPECIFIED BY GEETEL SUPPORT
DSL Modem 5 If your Geetel DSL modem is a black Comtrend AR-5312u or AR-5319 wireless modem/router combination, the lights across the front of the modem are as follows: POWER: This is the power light. It will remain solid telling you the power is on. ETH 1, 2, 3, 4: The 4 lights represent your equipment. There are 4 yellow ports on the back of the modem where you can plug your equipment in using Ethernet cables. Lights may be solid, but more than likely will flash as network traffic comes through modem. WPS: Wireless communication standard for connecting wireless equipment in your home. There is a WPS button on the front of the modem that allows you to use this WPS feature. Usually takes some past experience to get WPS to work correctly.
WiFi: Light will be solid green when wireless is enabled on the modem. By default the modem will have this feature turned on. Unless we have personalized the WiFi settings for the customer, the default SSID will be Geetel plus the last 4 characters of the modem’s MAC address and the password will be the 12 character MAC address found on the bottom of the modem. The password is case sensitive, lower case letters and numbers will be used. If you are using this wireless feature and the WiFi light is not on, push WiFi/WPS on/off button on front of modem for 3 seconds and wireless will enable. If you want wireless turned on for this modem please call the support line 765-258-3111 for us to personalize it for you or use the default SSID/Password settings described above after enabling WiFi on the modem. USB: Light is not used. DSL: This is your DSL sync system light. The light will flash at first and eventually become a solid green light when your DSL modem is talking with our DSL equipment. INTERNET: Light will become a solid green light after the ADSL light is a solid green light. Light becomes a solid green light once modem receives an IP address from Geetel giving the modem an internet connection. DO NOT HOLD IN RESET BUTTON ON DSL MODEM UNLESS SPECIFIED BY GEETEL SUPPORT
DSL Modem 6
If your Geetel DSL modem is a black Comtrend VR-3060 wireless modem/router combination, the lights across the front of the modem are as follows: POWER: This is the power light. It will remain solid telling you the power is on. ETH/WAN: Not used ETH 1, 2, 3, 4: The 4 lights represent your equipment. There are 4 yellow ports on the back of the modem where you can plug your equipment in using Ethernet cables. Lights may be solid, but more than likely will flash as network traffic comes through modem. WPS: Wireless communication standard for connecting wireless equipment in your home. There is a WPS button on the front of the modem that allows you to use this WPS feature. Usually takes some experience to get WPS to work correctly. WiFi 2.4G WiFi and 5G WiFi: Light will be solid green when wireless is enabled on the modem. By default the modem will have this feature turned on. Unless we have personalized the WiFi settings for the customer, the default SSID will be gtvl with password wireless. The password is case sensitive, lower case letters and numbers will be used. If you are using this wireless feature and the WiFi lights are not on, push 2.4G WiFi On/Off &WPS and/or 5.0G WiFi On/Off & WPS button on front of modem for 3 seconds and wireless will enable. If you want wireless turned on for this modem please call the support line 765-258-3111 for us to personalize it for you or use the default SSID/Password settings described above after enabling WiFi on the modem. USB: Light is not used. DSL: This is your DSL sync system light. The light will flash at first and eventually become a solid green light when your DSL modem is talking with our DSL equipment. INTERNET: Light will become a solid green light after the ADSL light is a solid green light. Light becomes a solid green light once modem receives an IP address from Geetel giving the modem an internet connection. DO NOT HOLD IN RESET BUTTON ON DSL MODEM UNLESS SPECIFIED BY GEETEL SUPPORT
USB: Light is not used. DSL: This is your DSL sync system light. The light will flash at first and eventually become a solid green light when your DSL modem is talking with our DSL equipment. INTERNET: Light will become a solid green light after the ADSL light is a solid green light. Light becomes a solid green light once modem receives an IP .
DSL networks use telephone lines; subscribers have dedicated lines between their own DSL modems and the closest DSL Access Multiplexer (DSLAM). The DSLAM multiplexes data between the access modems and upstream networks, as shown in Figure 1a. The most common type of DSL access is asymmetric
D-Link DSL- 3 0B ADSL Ethernet/USB Modem User Manual 4 Section 1 - General Information General Information The D-Link DSL- 3 0B is an ADSL modem offering the convenience of both Ethernet and USB connections. This user manual provides you with a simple and easy-to-understand for
The NETGEAR Broadband High-Speed DSL Modem Model DM200, in this man ual referred to as the modem, supports autodetection for universal DSL support.The modem is compatible with most major broadband DSL Inter net ser vice pro viders and suppor ts VDSL2 and ADSL2 . You can connect the modem directly to a computer , router, or WiFi router.
If you must install a DSL line into L1/L2 on the back of the phone, use a DSL splitter. Lines 1 and 2 share a telephone jack,so if you need to install a DSL line for telephone line 1 or line 2,you will need additional equipment to avoid interference. Any telephone line connected to L1/L2 cannot have a microfilter. It must have a DSL splitter.
pu 802: gen set dsl eng tm: 15kw 50/60hz . pu 803: gen set dsl eng tm: 30kw 50/60hz. pu 805: gen set dsl eng tm: 60kw 50/60hz. pu 797: gen set ded tm: 5kw 60hz. pu 798: gen set ded tm: 10kw 60hz. m107a2 trailer water 400 gal. standard automotive tool sets (sats) trailer. tool outfit hydraulic system: (hystru) pu 801: gen set dsl eng tm: 15kw 50 .
adapter into the power adapter jack on the back of the telephone base. Route the power adapter cord through this slot. end of the power adapter into a power outlet not controlled by a wall switch. Plug one end of the telephone line cord into a telephone jack or a DSL filter. If you have DSL high-speed Internet service, a DSL filter (not
DSL-2750E User Manual 1 . 1 Introduction . The DSL-2750E supports multiple line modes. With four 10/100 base-T Ethernet interfaces at the user end, the device provide high-speed ADSLs broadband connection to the Internet or In
appointment issued by the Bank Group, the terms and conditions of the letter of appointment will prevail. . Before accepting an assignment, STC/STT are required to acquaint themselves with the restrictions on relatives’ employment contained in SR 4.01, par. 5.03 and report to HR Operations (Bank and MIGA appointments) or Client Services (IFC appointments) any close relatives working for .
