CKL, CLJ, CRT, CLT, TWC, CLQ & HDC Split System Remote . - InspectAPedia
CLICK ANYWHERE on THIS PAGE to RETURN to AMANA - GOODMAN INFORMATION at InspectApedia Service Instructions CKL, CLJ, CRT, CLT, TWC, CLQ & HDC Split System Remote Coolers and CPLE, CPLJ, CPRT, CPLT & HDP Split System Remote Heat Pumps with R-22 Refrigerant Blowers, Coils, & Accessories This manual is to be used by qualified, professionally trained HVAC technicians only. Goodman does not assume any responsibility for property damage or personal injury for improper service procedures or services performed by an unqualified person. RS6200004 May 2006
INDEX IMPORTANT INFORMATION . 4 SYSTEM OPERATION . 72 PRODUCT IDENTIFICATION . 6 COOLING . 72 HEAT PUMPS AND COOLERS . 6 COOLING CYCLE . 72 COILS . 9 HEATING CYCLE . 72 AIR HANDLERS . 10 DEFROST CYCLE . 73 ACCESSORIES . 13 FAN OPERATION . 73 PRODUCT SPECIFICATIONS . 17 OPERATING INSTRUCTIONS . 74 CKL . 20 SCHEDULED MAINTENANCE . 134 CKL090-120 . 27 ONCE A MONTH . 134 CLJ . 30 ONCE A YEAR . 131 CLT . 37 TEST EQUIPMENT . 131 CRT . 41 COOLING & HEATING PERFORMANCE TEST . 131 TWC . 46 SERVICING . 132 HDC . 48 COOLING /HEAT PUMP- SERVICE ANALYSIS GUIDE . 132 CPLE . 49 S-1 Checking Voltage . 134 CPLE090-120 . 55 S-2 Checking Wiring . 134 CPLJ . 58 S-3 Checking Thermostat, Wiring & Anticipator . 135 CPRT . 62 S-3A Thermostat & Wiring . 135 CPLT . 67 S-3B Cooling Anticipator . 135 HDP . 70 S-3C Heating Anticipator . 135 UC . 71 S-3D Checking Encoded Thermostats . 136 H . 74 S-4 Checking Transformer & Control Circuit . 137 HT . 75 S-5 Checking Cycle Protector . 137 CAUF . 77 S-6 Checking Time Delay Relay . 137 CAPF . 78 S-7 Checking Contactor and/or Relays . 138 CHPF . 79 S-8 Checking Contactor Contacts . 138 A18-61 . 83 S-9 Checking Fan Relay Contact . 138 AR . 86 S-12 Checking High Pressure Control . 139 AR COMMERCIAL SERIES . 88 S-13 Checking Low Pressure Control . 139 AH . 91 S-15 Checking Capacitor . 139 AC . 93 S-15A Resistance Check . 140 ACHP . 96 S-15B Capacitance Check . 140 AWB . 97 S-16A Checking Fan & Blower Motor ARUF . 100 Windings (PSC Motors) . 141 ARPF . 103 S-16B Checking Fan & Blower Motor (ECM Motors) . 141 ARPT . 105 S-16C Checking ECM Motor Windings . 144 AER . 107 S-16D ECM CFM Adjustments . 144 AEPT . 111 S-17 WMC . 117 S-17A Resistance Test . 145 WMH . 119 S-17B Ground Test . 146 LOCATION AND CLEARANCES . 39 S-17D Operation Test . 146 PRODUCT DESIGN . 67 S-18 2 Checking Compressor Windings . 145 Testing Crankcase Heater (optional item) . 147
INDEX (Cont.) S-21 Checking Reversing Valve Solenoid . 147 S-111 Fixed Orifice Restriction Devices . 158 S-24 Testing Defrost Timer Board . 147 S-112 Checking Restricted Liquid Line . 158 S-25 Testing Defrost Control . 148 S-113 Refrigerant Overcharge . 158 S-26 Checking Heater Limit Control(s) . 148 S-114 Non-condensables . 158 S-27 Checking Heater Elements . 148 S-115 Compressor Burnout . 159 S-40 A, AR*F Electronic Blower Time Delay . 148 S-120 Refrigerant Piping . 159 S-41 AER, AEPT with Single Speed S-122 Replacing Reversing Valve . 161 Air Conditioning and Heat Pump . 150 S-202 Duct Static Pressure S-60 Electric Heater (optional item) . 151 & Static Pressure Drop Across Coils . 162 S-61A Checking Heater Limit Control(S) . 152 S-203 Air Handler External Static . 162 S-61B Checking Heater Fuse Line . 152 S-204 Coil Static Pressure Drop . 162 S-62 Checking Heater Elements . 152 WIRING DIAGRAMS . 163 S-100 Refrigeration Repair Practice . 152 AFE 18-60/18-60A . 163 S-101 Leak Testing . 153 CKL90-120 . 167 S-102 Evacuation . 153 CPLE, CPLJ, CRPT, CPLT . 168 S-103 Charging . 154 CPLE90-120 . 169 S-104 Checking Compressor Efficiency . 155 CLQ, CLJ, CKL, CRT, CLT . 170 S-105BThermostatic Expansion Valve . 155 WMH, HDP . 171 S-106 Overfeeding . 155 AR18-61 . 172 S-107 Underfeeding . 155 AR*F AIR HANDLER . 175 S-108 Superheat . 156 AR, ARUF, ARPF, ARPT18-60 . 176 S-109 Checking Subcooling . 157 AER, AEPT . 177 S-110 Checking Expansion Valve Operation . 157 WARNING HIGH VOLTAGE! Disconnect ALL power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury or death. 3
IMPORTANT INFORMATION Pride and workmanship go into every product to provide our customers with quality products. It is possible, however, that during its lifetime a product may require service. Products should be serviced only by a qualified service technician who is familiar with the safety procedures required in the repair and who is equipped with the proper tools, parts, testing instruments and the appropriate service manual. REVIEW ALL SERVICE INFORMATION IN THE APPROPRIATE SERVICE MANUAL BEFORE BEGINNING REPAIRS. IMPORTANT NOTICES FOR CONSUMERS AND SERVICERS RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS WARNING WARNING Hazards or unsafe practices which could result in property damage, product damage, personal injury or death. To prevent the risk of property damage, personal injury, or death, do not store combustible materials or use gasoline or other flammable liquids or vapors in the vicinity of this appliance. WARNING WARNING Do not connect to or use any device that is not design certified by Goodman for use with this unit. Serious property damage, personal injury, reduced unit performance and/or hazardous conditions may result from the use of such non-approved devices. ONLY individuals meeting the requirements of an “Entry Level Technician” as specified by the Air Conditioning and Refrigeration Institute (ARI) may use this information. Attempting to install or repair this unit without such background may result in product damage, personal injury, or death. WARNING Goodman will not be responsible for any injury or property damage arising from improper service or service procedures. If you install or perform service on this unit, you assume responsibility for any personal injury or property damage which may result. Many jurisdictions require a license to install or service heating and air conditioning equipment. WARNING The United States Environmental Protection Agency ("EPA") has issued various regulations regarding the introduction and disposal of refrigerants introduced into this unit. Failure to follow these regulations may harm the environment and can lead to the imposition of substantial fines. These regulations may vary by jurisdiction. A certified technician must perform the installation and service of this product. Should questions arise, contact your local EPA office. Violations of EPA regulations may result in fines or penalties. To locate an authorized servicer, please consult your telephone book or the dealer from whom you purchased this product. For further assistance, please contact: CONSUMER INFORMATION LINE GOODMAN MANUFACTURING COMPANY, L.P. TOLL FREE 1-877-254-4729 (U.S. only) email us at: customerservice@goodmanmfg.com fax us at: (731) 856-1821 (Not a technical assistance line for dealers.) Outside the U.S., call 1-713-861-2500. (Not a technical assistance line for dealers.) Your telephone company will bill you for the call. 4
IMPORTANT INFORMATION SAFE REFRIGERANT HANDLING While these items will not cover every conceivable situation, they should serve as a useful guide. WARNING Refrigerants are heavier than air. They can "push out" the oxygen in your lungs or in any enclosed space.To avoid possible difficulty in breathing or death: Never purge refrigerant into an enclosed room or space. By law, all refrigerants must be reclaimed. If an indoor leak is suspected, thoroughly ventilate the area before beginning work. Liquid refrigerant can be very cold. To avoid possible frostbite or blindness, avoid contact with refrigerant and wear gloves and goggles. If liquid refrigerant does contact your skin or eyes, seek medical help immediately. Always follow EPA regulations. Never burn refrigerant, as poisonous gas will be produced. WARNING To avoid possible injury, explosion or death, practice safe handling of refrigerants. WARNING HIGH VOLTAGE! Disconnect ALL power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury or death. WARNING To avoid possible explosion: Never apply flame or steam to a refrigerant cylinder. If you must heat a cylinder for faster charging, partially immerse it in warm water. Never fill a cylinder more than 80% full of liquid refrigerant. Never add anything other than R-22 to an R-22 cylinder or R-410A to an R-410A cylinder. The service equipment used must be listed or certified for the type of refrigerant used. Store cylinders in a cool, dry place. Never use a cylinder as a platform or a roller. WARNING To avoid possible explosion, use only returnable (not disposable) service cylinders when removing refrigerant from a system. Ensure the cylinder is free of damage which could lead to a leak or explosion. Ensure the hydrostatic test date does not exceed 5 years. Ensure the pressure rating meets or exceeds 400 lbs. When in doubt, do not use cylinder. WARNING System contaminants, improper service procedure and/or physical abuse affecting hermetic compressor electrical terminals may cause dangerous system venting. The successful development of hermetically sealed refrigeration compressors has completely sealed the compressor's moving parts and electric motor inside a common housing, minimizing refrigerant leaks and the hazards sometimes associated with moving belts, pulleys or couplings. Fundamental to the design of hermetic compressors is a method whereby electrical current is transmitted to the compressor motor through terminal conductors which pass through the compressor housing wall. These terminals are sealed in a dielectric material which insulates them from the housing and maintains the pressure tight integrity of the hermetic compressor. The terminals and their dielectric embedment are strongly constructed, but are vulnerable to careless compressor installation or maintenance procedures and equally vulnerable to internal electrical short circuits caused by excessive system contaminants. In either of these instances, an electrical short between the terminal and the compressor housing may result in the loss of integrity between the terminal and its dielectric embedment. This loss may cause the terminals to be expelled, thereby venting the vaporous and liquid contents of the compressor housing and system. A venting compressor terminal normally presents no danger to anyone, providing the terminal protective cover is properly in place. If, however, the terminal protective cover is not properly in place, a venting terminal may discharge a combination of (a) hot lubricating oil and refrigerant (b) flammable mixture (if system is contaminated with air) in a stream of spray which may be dangerous to anyone in the vicinity. Death or serious bodily injury could occur. Under no circumstances is a hermetic compressor to be electrically energized and/or operated without having the terminal protective cover properly in place. See Service Section S-17 for proper servicing. 5
PRODUCT IDENTIFICATION CONDENSING UNITS CLT 24 CLQ 1 1 24 1 PHASE 1 PHASE 24,000 BTUH 24,000 BTUH CONDENSING LOUVERED 13 SEER HDC 12 CONDENSING LOUVERED 14 SEER TWC 1 18 1 1 PHASE 1 PHASE 12,000 BTUH 18,000 BTUH HORIZONTAL DISHCARGE CONDENSER CKL 18 THROUGH WALL CONDENSER CLJ 1 18 1 PHASE 1 PHASE 18,000 BTUH 18,000 BTUH CONDENSING SERIES LOUVERED 10 SEER CRT 24 CONDENSING LOUVERED 12 SEER 24,000 BTUH CONDENSING SERIES T 13 SEER 6 1
PRODUCT IDENTIFICATION HEAT PUMPS CPLE CPLJ 1 18 18 1 1 PHASE 1 PHASE 18,000 BTUH 18,000 BTUH CONDENSING PUMP LOVERED EFFICIENCY 10 SEER CPLT CPRT 1 36 1 PHASE 36,000 BTUH CONDENSING PUMP LOVERED EFFICIENCY J 12 SEER HDP CONDENSING PUMP LOVERED EFFICIENCY J 12 SEER 24 X REVISION 24,000 BTUH CONDENSING HEAT PUMP REMOTE STYLE - T 13 SEER 12 12,000 BTUH HORIZONTAL DISHCARGE HEAT PUMP 7
PRODUCT IDENTIFICATION CONDENSING UNITS Model Description CKL18-120 1.5 to 10 Ton 10 SEER Condensing Units CLJ18-64 1.5 to 5 Ton 12 SEER Condensing Units CRT24-60 2 to 5 Ton 13 SEER Condensing Units CLT24-60 2 to 5 Ton 13 SEER Condensing Units CLQ24-60 2 to 5 Ton 14 SEER Condensing Units TWC18-30 2 to 5 Ton 10 SEER Condensing Units HDC12-24-1A Horizontal Discharge Air Cond. 1 thru 2 Ton HEAT PUMPS Descripton Model CPLE18-120 1.5 to 5 Ton 10 SEER Heat Pump Units CPLJ18-60 1.5 to 5 Ton 12 SEER Heat Pump Units CPRT24-60 2 to 5 Ton 13 SEER Heat Pump Units CPLT24-60 2 to 5 Ton 13 SEER Heat Pump Units HDP12-24-1A Horizontal Discharge Heat Pump 1 thru 2 Ton COILS Model 8 Description UC-18-62 Uncased Upflow Coil U-18-62 Cased Upflow Coil CAUF018-061 A Coil Upflow/Downflow Flowrator CAPF018-060 A Coil Upflow/Downflow Painted Cased Flowrator CAUX018-061 A Coil Upflow/Downflow w/ TXV CAPX018-061 A Coil Upflow/Downflow Painted Cased w/ TXV CHPF024-060 Horizontal A Coil Painted Cased w/ Flowrator CHPX024-060 Horizontal A Coil Painted Cased w/ TXV CACF018-061 Cased Upflow/Downflow Coil H-24F-61F Horizontal Evaporator Coil HT-18-61 Horizontal "Butt-up" Evaporator Coil
PRODUCT IDENTIFICATION COILS CA U F 018 A 2 Prefix A Revision A: Air Handler A: First Version B: Second Revision C: Painted Cased Coils are Painted in Architectural Gray Cabinet Finish P: Painted U: Unpainted Refrigerant 2: R-22 Nominal BTUH Expansion Device F: Flowrator T: TXV (Expansion Device 018: 024: 025: 030: 032: 036: 037: 048: 049: 060: 061: 062: 18,000 24,000 25,000 30,000 32,000 36,000 37,000 48,000 49,000 60,000 61,000 62,000 Cabinet Description CA Models (Cabinet Height) A: 14" B: 17½" C 21" D: 24½" Cabinet Description CH Models (Cabinet Height) U 18 UC 18 18,000 BTUH 18,000 BTUH CASED UPFLOW COILS H 24 UNCASED UPFLOW COILS HT 24,000 BTUH HORIZONTAL EVAPORATOR COILS A: 14" B: 17½" D: 24½" 24 24,000 BTUH HORIZONTAL "BUTT-UP" EVAPORATOR COIL 9
PRODUCT IDENTIFICATION AIR HANDLERS A * * * 024 -00 A -1 Product Type A Revision* A: Air Handler Motor E: ECM Motor R: PSC Motor Electrical Supply 1: 208-230V/60Hz/1ph Cabinet Finish P: Painted U: Unpainted Feature Expansion Device F: Flowrator T: TXV (Expansion Device Nominal Capacity 018: 024: 030: 032: 036: 042: 048: 049: 060: 061: 1½ Tons 2 Tons 2½ Tons 2½ Tons 3 Tons 3½ Tons 4 Tons 4 Tons 5 Tons 5 Tons A: First Series B: Downflow C: Factory-sealed Series Factory-Installed Electric Heat 00: None 05: 5 KW et al *All revisions A or higher are Architectural Gray AR 60 18- 18,000 BTUH 24- 24,000 BTUH 30, 32- 30,000 BTUH 36- 36,000 BTUH 42- 42,000 BTUH 48,49- 48,000 BTUH 60,61- 60,000 BTUH AR-AIRHANDLER WITH COIL (2nd Generation) All Airhandlers use DIRECT DRIVE MOTORS. Power supply is AC 208-230v, 60 hz, 1 phase. 10
PRODUCT IDENTIFICATION AIR HANDLERS A 24 00 2 RA SECOND GENERATION 50 HTZ MODEL W/OPTION FOR HEATER KIT * 24 - 24,000 BTUH (7.0 KW) 36 - 36,000 BTUH (10.5 KW) 48 - 48,000 BTUH (14.0 KW) 60 - 60,000 BTUH (17.6 KW) Air Handler w/Coil AER 60 24 - 24,000 BTUH 30 - 30,000 BTUH 36 - 36,000 BTUH 48 - 48,000 BTUH 60 - 60,000 BTUH AER-AIRHANDLER WITH COIL (2nd Generation) AWB 24 08 AC C 24 05 D CIRCUIT BREAKER CIRCUIT BREAKER KW OF HEAT KW OF HEAT 24,000 BTUH AIR HANDLER WALL MOUNT B REVISION 24,000 BTUH AIR HANDLER CEILING MOUNT All Airhandlers use DIRECT DRIVE MOTORS. Power supply is AC 208-230v, 60 hz, 1 phase. 11
PRODUCT IDENTIFICATION AIR HANDLERS Description Model AR18-120 Elec. Cooling & Heat Pump Air Handler AW 18-30 Vertical Wall Mount Air Handler AER24-60 Multi-Position Variable Spd Air Handler ACHP18-36 Hydronic Heat Air Handler AH18-36 Hydronic Heat Air Handler AC18-36 AC Electric Heat Air Handler AWB18-36 Vertical Wall Mount Air Handler ARUF018-061 Multi-Position Electric Heat Air Handler w/ Flowrator ARPT024-060 Multi-Position Painted Electric Heat Air Handler w/ TXV ARPF024-060 Multi-Position Painted Electric Heat Air Handler w/ Flowrator AEPT030-060 Multi-Position Painted Variable Spd. Air Handler w/ TXV WMC12-24-1A Ductless Air Conditioning Indoor Section 1 thru 2 Ton WMH12-24-1A Ductless Heat Pump Indoor Section 1 thru 2 Ton 12
ACCESSORIES SPLIT SYSTEM AIR CONDITIONING ACCESSORIES SPLIT SYSTEM HEAT PUMP ACCESSORIES Description Model Description Model LA-01 Low Ambient Kit AFE-18 All Fuel Kit HLPK-01 High and Low Pressure Switch Kit OT18-60 Outdoor Thermostat Kit LPS-01 Low Pressure Kit EH18-60 Emergency Heat Relay Kit FP-01 Freeze Protection Kit for AC Air Handlers & Coils HPSK-01 Heat Pump Shut Off; for AC Air Handlers ASC01A Anti-Short Cycle Control Kit FP-01 Freeze Protection Kit; for AC Air Handlers ASC01A Anti-Short Cycle Control Kit COIL ACCESSORIES Description Model Used With These Units TX3N2 TXV Kit 1.5 to 3 Ton Air Cond. & Heat Pump CAUF,CAPF CHPF TX5N2 TXV Kit 3.5 to 5 Ton Air Cond. & Heat Pump CAUF,CAPF CHPF DFK Downflow Kits U- UC coils DFKT Downflow Kits U-UC Coils COIL INSULATION KIT FOR DOWNFLOW APPLICATIONS Chassis Size Insulation Kit Small DPI18-30/20 Medium DPI36-42/20 Large DPI48-60/20 NOTE: Each kit contains enough material to modify 20 coils. 13
ACCESSORIES AIR HANDLER ACCESSORIES Model Description Used With These Units WCK-01 Water Circulator Timer Kit AH, ACHP FIL18-32 Washable Air Filter AR,AER,AEPT,ARPT,ARPF, ARUF FIL36-42 Washable Air Filter AR,AER,AEPT,ARPT,ARPF, ARUF FIL48-61 Washable Air Filter AR,AER,AEPT,ARPT,ARPF, ARUF CAP-1 Ceiling Access Panels AC,ACHP CAP-2 Ceiling Access Panels AC,ACHP CAP-3 Ceiling Access Panels AC,ACHP CAP-1L Ceiling Access Panels AC,ACHP CAP-2L Ceiling Access Panels AC,ACHP CAP-3L Ceiling Access Panels AC,ACHP WAD-1 Wall Access Door AH,AWB WAD-2 Wall Access Door AH,AWB XV18-36C Expansion Valve Kit, Non-bleed APRF/ARUF18-36 XV42-60C Expansion Valve Kit, Non-bleed ARPF/ARUF42-60 XVB18-36C Expansion Valve Kit, 20% bleed ARPF/ARUF18-36 XVB42-60C Expansion Valve Kit, 20% bleed ARPF/ARUF42-60 TX3N2 TXV Kit 1.5 to 3 Ton Air Cond. & Heat Pump ARPF/ARUF18-36 TX5N2 TXV Kit 3.5 to 5 Ton Air Cond. & Heat Pump AAPF/ARUF42-60 DPI18-30/20 Coil Insulation Kit; Small Chassis { Downflow} AEPT,ARPT,ARUF DPI36-42/20 Coil Insulation Kit; Medium Chassis { Downflow} AEPT,ARPT,ARUF DPI48-60/20 Coil Insulation Kit; Large Chassis { Downflow} AEPT,ARPT,ARUF FP-01 Freeze Protection Kit All Models. OT/EHR18-60 OUTDOOR THERMOSTAT & EMERGENCY HEAT RELAY OT18-60 Thermostat Dial 315º COLD WARM (Turn Clockwise) DEAD DIAL (Turn Counterclockwise) 45º Set Point Adjustment Screw 14 Set Point Indicator Mark (Shown @ Oº F)
ACCESSORIES EXPANSION VALVE KITS For Applications requiring 1/4 FLARE CONNECTION BULB TO BE LOCATED AT 10 OR 2 O'CLOCK a field installed access fitting BULB SUCTION LINE EVAPORATOR COIL PISTON SEAL SUPPLIED W/ KIT SEAL SUPPLIED W/ KIT EXPANSION VALVE TAILPIECE SEAL DISTRIBUTOR BODY REMOVE BEFORE INSTALLING EXPANSION VALVE 3/8"SWEAT 7/8" NUT For Applications not requiring 1/4' FLARE CONNECTION a field installed access fitting BULB TO BE LOCATED AT 10 OR 2 O'CLOCK BULB SUCTION LINE PISTON EXPANSION VALVE DISTRIBUTOR BODY EVAPORATOR COIL TAILPIECE SEAL 3/8"SWEAT SEAL SUPPLIED W/ KIT REMOVE BEFORE INSTALLING EXPANSION VALVE SEAL SUPPLIED W/ KIT 7/8" NUT EXPANSION VALVE KITS FOR AIR CONDITIONING-ONLY APPLICATIONS Kit Number Use With Description XVB18-36C ARUF018 to ARUF036 20% Bleed Valve XVB42-60C ARUF042 to ARUF060 20% Bleed Valve XV18-36C ARUF018 to ARUF 036 Non-Bleed Valve XV42-60C ARUF042 to ARUF061 Non-Bleed Valve 15
ACCESSORIES PISTON KIT CHART OUTDOOR UNIT CKL18-1* CKL24-1* CKL30-1* CKL36-1* CKL42-1* CKL49-1*/3* CKL60-1*/3* CKL62-1* CLJ18-1* CLJ24-1* CLJ30-1* INDOOR UNIT BTU's 18000 24000 29000 31000 32000 36000 AH18 AE(R)24 24000 29000 30000 31000 32000 36000 AE(R)24 24000 29000 30000 31000 32000 36000 42000 49000 AE(R)30 AE(R)36 35000 36000 42000 49000 AE(R)36 42000 47000 48000 49000 60000 AE(R)48 47000 48000 49000 59000 60000 61000 60000 61000 62000 AE(R)60 59000 60000 61000 62000 AE(R)60 18000 24000 29000 30000 31000 32000 36000 AH18 AE(R)24 24000 29000 30000 31000 32000 36000 AE(R)24 30000 31000 32000 36000 AE(R)30 AE(R)36 INDOOR PISTON SIZE .052 .052 .052 .055 .055 .055 .049 .055 .059 .059 .059 .062 .062 .062 .062 .065 .065 .065 .065 .065 .065 .068 .068 .068 .068 .071 .071 .073 .073 .074 .078 .078 .078 .078 .078 .082 .082 .082 .082 .082 .082 .082 .090 .090 .090 .090 .093 .093 .093 .093 .093 .055 .055 .055 .055 .055 .055 .055 .052 .055 .057 .057 .057 .057 .057 .057 .057 .065 .065 .065 .065 .065 .065 (*) SIGNIFIES UNIT REVISION. (1) PISTON SUPPLIED WITH THE OUTDOOR UNIT. (2) PISTON SUPPLIED WITH THE INDOOR UNIT. (3) PURCHASE PISTON KIT FROM DISTRIBUTOR. (4) B1789865 PISTON PROVIDED IN THE INDOOR UNIT. (5) PISTON PROVIDED IN THE OUTDOOR UNIT LIQUID LINE SERVICE VALVE. PISTON KIT PART NO. (2) B1789852 (3) B1789852 (3) B1789855 (3) B1789855 (3) B1789855 (3) (2) B1789855 (3) (2) (2) B1789859 (3) B1789862 (3) B1789862 (3) B1789862 (3) (2) (3) (4) (2) B1789865 (3) B1789865 (3) B1789865 (3) B1789868 (3) B1789868 (3) (2) B1789868 (3) (2) (2) B1789873 (3) B1789873 (3) (2) (2) B1789878 (3) B1789878 (3) B1789878 (3) B1789878 (3) (2) (2) (2) (2) B1789882 (1) B1789882 (1) B1789882 (1) (2) (2) (2) (2) B1789893 (1) B1789893 (1) B1789893 (1) B1789893 (1) B1789893 (1) B1789855 (1) B1789855 (1) B1789855 (1) B1789855 (1) B1789855 (1) B1789855 (1) B1789855 (1) B1789852 (3) B1789855 (1) B1789857 (1) B1789857 (1) B1789857 (1) B1789857 (1) B1789857 (1) B1789857 (1) B1789857 (1) (2) B1789865 (1) B1789865 (1) B1789865 (1) B1789865 (1) B1789865 (1) OUTDOOR UNIT INDOOR UNIT BTU's CLJ36-1* 36000 42000 47000 49000 AE(R)36 42000 48000 49000 59000 60000 AE(R)48 48000 49000 59000 60000 61000 62000 AE(R)48 59000 60000 61000 62000 AE(R)60 24000 29000 31000 32000 36000 42000 49000 AE(R)24 30000 32000 36000 42000 49000 AE(R)36 47000 48000 49000 60000 AE(R)36 42000 48000 49000 61000 62000 AE(R)48 48000 49000 60000 61000 62000 AE(R)48 60000 61000 62000 AE(R)60 31000 32000 36000 42000 47000 49000 AE(R)24 31000 32000 36000 60000 61000 62000 AE(R)36 49000 60000 61000 62000 AE(R)36 49000 60000 61000 62000 AE(R)48 49000 60000 61000 62000 AE(R)48 60000 61000 62000 AE(R)60 CLJ42-1* CLJ48-1* CLJ60-1* CLT24-1*/CRT24-1* CLT30-1*/CRT30-1* CLT36-1*/CRT36-1* CLT42-1*/CRT42-1* CLT48-1*/CRT48-1* CLT60-1*/CRT60-1* CLQ24-1* CLQ30-1* CLQ36-1* CLQ42-1* CLQ48-1* CLQ60-1* 16 INDOOR PISTON SIZE .071 .073 .073 .073 .074 .078 .078 .078 .078 .078 .078 .082 .082 .082 .082 .082 .082 .082 .093 .093 .093 .093 .093 .055 .055 .055 .055 .055 .055 .055 .055 .065 .065 .065 .065 .065 .065 .074 .074 .074 .074 .074 .078 .078 .078 .080 .080 .082 .082 .082 .082 .082 .082 .082 .088 .088 .088 .088 .059 .059 .059 .059 .059 .059 .059 .065 .065 .065 .065 .065 .065 .065 .073 .073 .073 .073 .073 .080 .080 .080 .080 .080 .082 .082 .082 .082 .082 .090 .090 .090 .090 PISTON KIT PART NO. (2) B1789873 (1) B1789873 (1) B1789873 (1) (2) (2) B1789878 (1) B1789878 (1) B1789878 (1) B1789878 (1) B1789878 (1) (2) (2) B1789882 (1) B1789882 (1) B1789882 (1) B1789882 (1) (2) B1789893 (1) B1789893 (1) B1789893 (1) B1789893 (1) B1789893 (1) B1789855 (1) B1789855 (1) B1789855 (1) B1789855 (1) B1789855 (1) B1789855 (1) B1789855 (1) B1789855 (1) (2) B1789865 (1) B1789865 (1) B1789865 (1) B1789865 (1) B1789865 (1) B1789874 (1) B1789874 (1) B1789874 (1) B1789874 (1) (2) (2) B1789878 (3) B1789878 (3) B1789880 (1) B1789880 (1) (2) (2) (2) B1789882 (1) B1789882 (1) B1789882 (1) (2) B1789888 (1) B1789888 (1) B1789888 (1) B1789888 (1) B1789859 (1) B1789859 (1) B1789859 (1) B1789859 (1) B1789859 (1) B1789859 (1) B1789859 (1) B1789865 (1) B1789865 (1) B1789865 (1) B1789865 (1) B1789865 (1) B1789865 (1) B1789865 (1) B1789873(1) B1789873(1) B1789873(1) B1789873(1) B1789873(1) B1789880 (1) B1789880 (1) B1789880 (1) B1789880 (1) B1789880 (1) (2) B1789882 (1) B1789882 (1) B1789882 (1) (2) (2) (2) (2) (2)
ACCESSORIES OUTDOOR UNIT CPLE18-1* CPLE24-1* CPLE30-1* CPLE36-1* CPLE42-1* CPLE48-1* CPLE60-1*/3* CPLJ18-1* CPLJ24-1* CPLJ30-1* CPLJ36-1* CPLJ42-1* 18000 24000 29000 36000 24000 29000 30000 31000 32000 36000 29000 30000 31000 32000 36000 48000 35000 36000 42000 47000 48000 49000 42000 47000 48000 49000 47000 49000 59000 60000 61000 62000 61000 18000 24000 32000 36000 AE(R)24 24000 30000 31000 32000 36000 42000 AE(R)24 30000 32000 36000 42000 AE(R)30 AE(R)36 36000 42000 INDOOR PISTON SIZE .052 .052 .052 .052 .059 .059 .059 .059 .059 .059 .065 .065 .068 .068 .068 .068 .073 .073 .073 .073 .073 .073 .07
twc 18 18,000 btuh 1 1 phase condensing series louvered 10 seer ckl 18 18,000 btuh 1 1 phase condensing louvered 12 seer clj 18 18,000 btuh 1 1 phase condensing series t 13 seer crt 24 24,000 btuh condensing louvered 13 seer clt 24 24,000 btuh 1 1 phase condensing louvered 14 seer clq 24 24,000 btuh 1 1 phase
This manual covers the set up and use of the Norbar TWC. Part Number Model Torque Range 60312 TWC 400 AUTO 0 - 400 N·m 60313 TWC 1500 AUTO 0 - 1500 N·m This product is intended for testing torque wrenches. TWC Markings Pictograms Meaning WARNING: LIVE PARTS INSIDE. DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE.
CRT CRT 101 Introduction to Commercial Art 25.00 25.00 25.00 25.00 CRT 107 Photo Imaging Assembly 25.00 25.00 25.00 25.00 CRT 108 Line and Halftone Photography 25.00 25.00 25.00 25.00 CRT 112 Electronic Pagination 35.00 35.00 35.00 35.00 CRT 204 Photography 50.00 50.00 50.00 50.00 CRT 206 Digital Imaging 40.00 40.00 40.00 40.00
CLP-320/320N/ 325/325W CLT-K407S CLT-K4072S (EU) Average 1,500 standard pages 2 CLT-C407S CLT-C4072S (EU) Average 1,000 standard pages CLT-M407S CLT-M4072S (EU) . Samsung printing supplies are specially designed to work together with Samsung printer. We assure optimal print quality with sharp, clear output from first print to last. .
2011 UMass Wood Structures Symposium M. Mohammad . 06/09/2011 Overview Importance of connections in CLT assemblies Common connection details/techniques in CLT assemblies: European experience Summary of recent research on CLT connections . CLT Wall & metal plated floor trusses. Self tapping screws are used Mixed CLT with other Wood Based .
iv TWC-701 AND TWC-704 ADAPTORS Figure 1: Safety Symbols EMC AND SAFETY The TWC-701 and TWC-704 products meet all relevant CE and FCC specifications set out below: EN55103-1 Electromagnetic compatibility. Product family standard for audio, video, audio-visual, and entertainment lighting control apparatus for professional use. Part 1: Emissions.
and compression ratio. The results indicate that Huffman-CRT on text outperforms LZW-CRT for compression size by 55.64% to 57.11%, compression time for Huffman-CRT is 44.61s better than LZW-CRT with 55.39s while Huffman-CRT also outperformed LZW-CRT by 3.70x to 2.37x for compression ratio. 1. INTRODUCTION
1 P a g e CRT 302 – ACLS RENEWAL COURSE CRT 302 ACLS Renewal Course (Baltimore) CRT 302 ACLS Renewal Course (DC) Please bring your MedStar ID if you are an employee or a photo ID if you are a non-employee, as well as your current AHA BLS card or the print out from completion of the Online BLS course (CRT 107) as
the standard represented by the Associated Board of the Royal Schools of Music (ABRSM) Grade 5 Theory examination. The module will introduce you to time-based and pitch-based notation, basic principles of writing melody, harmony and counterpoint, varieties of rhythmic notation, simple phrasing, and descriptive terms in various languages.
