Bearings - Hellopro.fr
Bearings 355 14. Bearings Section.indd 355 16/10/2008 16:48:20
Bearings Tolerance and Accuracy Tolerance & Accuracy According to dimensional tolerances and run out accuracy the deep groove ball bearing grades are: ABEC-1, ABEC-3, ABEC-5. ABEC-1 is standard grade, while ABEC-3 is higher and ABEC-5 being the highest. These tolerance grades correspond to the precision adopted by the International Standard Organization (IS0492). ABEC-1 Normal Class ABEC-3 Class 6 ABEC-5 Class 5 Symbols The following symbols are used to identify boundary dimensions, size variations and runout errors. ABs: Single inner ring width deviation from basic VBs: lnner ring width variation d: Basic bore diameter C: Basic outer ring width Admp: Single plane mean bore diameter deviation in a single radial plane Cs: Single outer ring width deviation from basic Vcs: Outer ring width variation Kia: Radial runout of assembled bearing inner ring Kea: Radial runout of assembled bearing outer ring Vdp: Bore diameter variation in a single radial Vdmp: Mean bore diameter variation D: Basic outside diameter ADmp: Single plane means outside diameter deviation from basic VDp: Outside diameter variation a single radial VDmp: B: Sd: lnner ring reference face runout with bore SD: Outside cylindrical surface runout with outer ring reference face Mean outside diameter variation Sia: Axial runout of assembled bearing inner ring Basic inner ring width Sea : Axial runout of assembled bearing outer ring Inner ring of 0 grade tolerance V dp 2) d mm over 0.6 1) 2.5 10 18 30 50 r dmp incl. 2.5 10 18 30 50 80 high 0 0 0 0 0 0 Diameter Series I low -8 -8 -8 -10 -12 -15 9 0,1 2,3,4 10 10 10 13 15 19 max 8 8 8 10 12 19 6 6 6 8 9 11 r Bs V dmp Kia max 6 6 6 8 9 11 max 10 10 10 13 15 20 high 0 0 0 0 0 0 V Bs low -40 -120 -120 -120 -120 -150 max 12 15 20 20 20 25 0.6 is included No values for diameter series 7, 8. Outer ring of 0 grade tolerance V Dp 2) 4) D mm Open Bearings r Dmp Capped Bearings 2) 3) V DMP 4) Kea r Cs V cs Diameter Series 9 over 1) 2.5 6 18 30 50 incl. 6 18 30 50 80 high 0 0 0 0 0 low -8 -8 -9 -11 -13 10 10 12 14 16 80 120 0 -15 19 0,1 2,3,4 2,3,4 19 13 11 9 8 6 6 7 8 10 10 10 12 16 20 max 6 6 7 8 10 max 15 15 15 20 25 8 11 26 11 35 max high low max Identical to rBs and V Bs of inner ring of same bearing. No values for diameter series 7,8. No values for diameter series 9,0,1. All dimensions in millimetres unless otherwise stated. Every effort has been taken to ensure that the data listed in this catalogue is correct. Challenge accepts no liability for any inaccuracies or damage caused. 356 14. Bearings Section.indd 356 16/10/2008 16:48:21
Bearings Tolerance and Materials Inner ring of 6 grade tolerance V dp 2) d mm r dmp over 0.6 1) 2.5 10 18 30 50 incl. 2.5 10 18 30 50 80 high 0 0 0 0 0 0 Diameter Series I low -7 -7 -7 -8 -10 -12 9 0,1 2,3,4 9 9 9 10 13 15 max 7 7 7 8 10 15 5 5 5 6 8 9 r Bs V dmp Kia max 5 5 5 6 8 9 max 5 6 7 8 10 10 high 0 0 0 0 0 0 V Bs low -40 -120 -120 -120 -120 -150 max 12 15 20 20 20 25 0.6 is included No values for diameter series 7, 8. Outer ring of 6 grade tolerance V Dp 2) 4) D mm Open Bearings r Dmp Capped Bearings 2) 3) V DMP 4) Kea r Cs V cs Diameter Series 9 over 1) 2.5 6 18 30 50 incl. 6 18 30 50 80 high 0 0 0 0 0 low -7 -7 -8 -19 -11 9 9 10 11 14 80 120 0 -13 16 0,1 2,3,4 2,3,4 7 7 8 9 11 5 5 6 7 8 9 9 10 13 16 max 5 5 6 7 8 max 8 8 9 10 13 16 10 20 10 18 max high low max Identical to rBs and V Bs of inner ring of same bearing. 2.5 is included No values for diameter series 7,8. No values for diameter series 9,0,1. Materials Rings & Balls Gcr15 high carbon chromium bearing steel is the standard material for precision bearing rings and balls. The chemical composition of the material is shown in table one and the contrast of Bearing Steel No. of each country in table two. Table one Steel No. SAE 52100 Chemical Composition C Si Mn P S Cr Mo 0.98-1.1 0.15-0.3 0.25-0.45 0.025 0.025 1.3-1.1 - Table two Country China ISO U.S.A. Germany Japan Sweden Bearing Steel No. Gcr15 683/XVII1 (AISI)52100 (Din)0100Cr6 (Jis)SUJ2 SKF3 Retainers Shields & Seals The retainer is normally made of H62 copper sheet or 08F cold rolled steel belt, however, in cases of corrosive environment, misalignment, or high speed operation, stainless steel, nylon, or phenolic resins will be used upon request. Shields are made of steel as standard, and the optional AISI-300 stainless available when required. A variety of sealing materials are used to meet the requirements of high temperature operation and compatibility with greases. Buna Nitryl is the standard material used, while fluorocarbon, silicone, and Teflon seals are commonly specified for high temperature. Every effort has been taken to ensure that the data listed in this catalogue is correct. Challenge accepts no liability for any inaccuracies or damage caused. All dimensions in millimetres unless otherwise stated. 357 14. Bearings Section.indd 357 16/10/2008 16:48:21
Bearings Vibration and Noise Vibration & Noise Vibration and noise in bearings have three classifications Z1, Z2, Z3, It is measured by the instrument of SO910-II. For special requirements, it is measured by BVT-1 and classified as V1, V2, V3 The data is shown below: Maximum vibration acceleration of single bearing d mm (0) Diameter Series (2) Diameter Series (3) Diameter Series Z Z1 Z2 Z3 Z Z1 Z2 Z3 Z Z1 Z2 Z3 5 37 36 34 30 38 37 34 32 39 37 35 33 6 37 36 34 30 38 37 34 32 39 37 35 33 7 39 38 35 31 40 38 36 34 42 39 37 35 8 39 38 35 31 40 38 36 34 44 41 38 36 9 41 40 36 32 42 40 37 35 45 42 39 37 10 43 42 38 33 44 42 39 35 46 44 40 37 12 44 43 39 34 45 43 39 35 47 45 40 37 15 45 44 40 35 46 44 41 36 48 46 42 38 17 46 44 40 35 47 45 41 36 49 47 42 38 20 47 45 41 36 48 46 42 38 50 48 43 39 22 47 45 41 36 48 46 42 38 50 48 43 39 25 48 46 42 38 49 47 43 40 51 49 44 41 30 49 47 43 39 50 48 44 41 52 50 45 42 35 51 49 45 41 52 50 46 43 54 52 47 44 40 53 51 46 42 54 52 47 44 56 54 49 45 Tolerance data for vibration speed of single bearing D mm V1 V2 V3 Low Brand Medium Brand High Brand Low Brand Medium Brand High Brand Low Brand Medium Brand High Brand 5 90 60 50 58 36 30 35 21 18 6 90 60 50 58 36 30 35 21 18 7 110 80 65 72 48 40 44 28 24 8 110 80 65 72 48 40 44 28 24 9 110 80 65 72 48 40 44 28 24 10 140 100 85 90 60 50 55 35 30 12 140 100 85 90 60 50 55 35 30 15 180 130 100 110 78 60 65 46 35 17 180 130 100 110 78 60 65 46 35 20 220 160 125 130 100 75 80 60 45 22 220 160 125 130 100 75 80 60 45 25 220 160 125 130 100 75 80 60 45 30 250 200 160 150 120 100 90 75 60 35 250 200 160 150 120 100 90 75 60 40 300 250 220 180 150 130 110 90 80 All dimensions in millimetres unless otherwise stated. Every effort has been taken to ensure that the data listed in this catalogue is correct. Challenge accepts no liability for any inaccuracies or damage caused. 358 14. Bearings Section.indd 358 16/10/2008 16:48:21
Bearings Lubrication and Packing Clearance Grease & Oil In accordance with the ISO 5753 standard, The radial clearance can be classified into C2, standard, C3 C4 and C5 groups. Different specification will be required depending on customers bearing application. Data of standard radial clearance for bearings under no load as follows: Open bearings are lubricated with shell A12 or WINSORL 245X. ball bearings with two shields(ZZ)or two seals(2RS) are greased with Chevron SR#2 or Mobil #28 grease as standard and are ready to use. Upon request ball bearings can be lubricated with other greases or oil, Contact: technicalsupport@challengeproduction.com for specific application. Bore Group Standard Group Group Group Group Over To Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. 2.5 6 0 7 2 13 8 23 11 26 16 30 6 10 0 7 2 13 8 23 14 29 20 37 10 18 0 9 3 18 11 25 18 33 25 45 18 24 0 10 5 20 13 28 20 36 28 48 24 30 1 11 5 20 13 28 23 41 30 53 30 40 1 11 6 20 15 33 28 46 40 64 40 50 1 11 6 23 18 36 30 51 45 73 Lubricant type & specification Brand Name Exxon Mobil Shell Dupont kYODO NIPPGK Motor CSR Code Basic Type Grease Operating Temp. C Uses Beacon 325 Synthetic grease -55 to 120 General purpose grease Andok C Channeling petroleum grease -30 to 120 Smooth running, long life Andok 260 Channeling Petreleum grease -30 to 95 Excillent high speed, low torque, low mass Hp Lithium complex -30 to 110 Vibration moderate speeds and good corrosion resistance 28 (mil-G-81322) Synthetic hydrocarbon -55 to 180 Wide temperature range, good low temperature Shell Dolium R petroleum grease -40 to 150 Good corrosion resistance and water resistance Alvania 2 Mineral grease -35 to 120 Long life and wide range of applications Alvania RIQ2 Mineral grease -25 to 120 Good water resistance and low noise, good low temperature resistance Jvania R Grease 2 (EP) Mineral grease -10 to 110 Good water resistance Krytox 240 AC (Mill-G 277617) Fiuorinated grease -35 to 290 High temperature stability with good lubrication properties Multemp SB-M Diester -40 to 170 High temperature and speed, good low temperature resistance SRL Synthetic grease -40 to 150 Low noise, low torque and special requirements Multemp PSI Diester -40 to 130 Good low temperature resistance and low noise MpOX-2 Diester -30 to 200 High temperature and loading Motor No.2 Mineral grease -30 to110 Wide application, general purpose Packing Rust resisting Generally the bearings are packed in plastic pipes or small boxes. Then packed into a carton. Special packing arrangements can be arranged prior to order. Under normal storage conditions the rust resisting period is six months, after this period the product should be checked and rust resisted again according to guidelines to prevent rust from occuring. Every effort has been taken to ensure that the data listed in this catalogue is correct. Challenge accepts no liability for any inaccuracies or damage caused. All dimensions in millimetres unless otherwise stated. 359 14. Bearings Section.indd 359 16/10/2008 16:48:22
Bearings 6000 Series 6000 Series 6000 Series Shape Dimension Bearing Number Basic Load Rating kN Bore d O.d D Width B Chamfer r min Dynamic cr 5 6 7 8 9 10 12 15 17 20 25 30 35 40 45 50 55 60 65 70 75 14 17 19 22 24 26 28 32 35 42 47 55 62 68 75 80 90 95 100 110 115 5 6 6 7 7 8 8 9 10 12 12 13 14 15 16 16 18 18 18 20 20 0.2 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.6 0.6 1.0 1.0 1.0 1.0 1.0 1.1 1.1 1.1 1.1 1.1 1.05 1.95 2.88 3.32 3.35 4.58 5.10 5.58 6.00 9.38 10.1 10.18 12.46 13.09 21.0 21.8 28.3 29.5 30.5 38.1 39.7 Static Cor Max Runout Speed rev/min Ball Complement Grease Oil Quantity Size 32000 30000 28000 26000 22000 20000 19000 18000 17000 15000 13000 10000 9000 8500 7200 6400 5700 5000 5300 5000 4700 40000 38000 36000 34000 30000 28000 26000 24000 22000 19000 17000 14000 12000 11000 9000 7800 7000 6300 6300 5900 5600 7 6 6 7 7 7 8 9 10 9 10 11 11 12 12 13 11 12 2.381 3.175 3.969 3.969 3.969 4.763 4.763 4.763 4.763 6.350 6.350 7.144 7.938 7.938 8.731 8.731 11.112 11.112 Weight kg 6000 Series 605 606 607 608 609 6000 6001 6002 6003 6004 6005 6006 6007 6008 6009 6010 6011 6012 6013 6014 6015 All dimensions in millimetres unless otherwise stated. 0.50 0.72 1.08 1.38 1.40 1.98 2.38 2.85 3.25 5.02 5.85 6.91 8.65 9.44 15.1 16.6 21.2 23.2 25.2 30.9 33.5 0.0045 0.0057 0.0071 0.011 0.014 0.018 0.021 0.026 0.036 0.069 0.075 0.116 0.155 0.185 0.231 0.250 0.362 0.385 0.421 0.604 0.649 Every effort has been taken to ensure that the data listed in this catalogue is correct. Challenge accepts no liability for any inaccuracies or damage caused. 360 14. Bearings Section.indd 360 16/10/2008 16:48:22
Bearings 6200 Series 6200 Series 6200 Series Shape Dimension Bearing Number Basic Load Rating kN Bore d O.d D Width B Chamfer r min Dynamic cr 623 624 625 626 627 628 629 6200 6201 6202 6203 6204 6205 6206 6207 6208 6209 6210 6211 6212 6213 3 4 5 6 7 8 9 10 12 15 17 20 25 30 35 40 45 50 55 60 65 10 13 16 19 22 24 26 30 32 35 40 47 52 62 72 80 85 90 100 110 120 4 5 5 6 7 8 8 9 10 11 12 14 15 16 17 18 19 20 21 22 23 0.15 0.2 0.3 0.3 0.3 0.3 0.3 0.6 0.6 0.6 0.6 1.0 1.0 1.0 1.1 1.1 1.1 1.1 1.5 1.5 1.5 0.50 1.15 1.88 2.80 3.28 3.35 4.45 5.10 6.82 7.65 9.58 9.87 10.75 14.96 19.74 22.70 32.5 35 43.5 52.5 57.2 6214 60 125 24 1.5 6215 75 130 25 1.5 Static Cor Max Runout Speed rev/min Ball Complement Weight kg Grease Oil Quantity Size 0.22 0.45 0.68 1.05 1.35 1.40 1.95 2.38 3.05 3.72 4.47 6.18 10.02 13.65 15.92 17.70 20.4 23.2 29.2 36.0 40.0 38000 36000 32000 28000 26000 24000 22000 19000 18000 17000 16000 14000 12000 9500 8500 8000 7800 7100 6400 6000 4400 48000 45000 40000 36000 34000 32000 30000 26000 24000 22000 20000 18000 16000 13000 11000 10000 9200 8300 7600 7000 5300 6 6 6 7 7 7 8 7 8 8 8 9 9 9 9 10 10 10 10 2.381 3.175 3.969 3.969 3.969 4.763 4.763 5.953 5.953 6.747 7.938 7.938 9.525 11.1125 12.000 12.000 12.700 14.288 15.081 62.2 44.1 4200 5000 1.070 67.4 49.3 4000 4600 1.180 6200 series 0.0015 0.0032 0.0048 0.0075 0.012 0.017 0.019 0.028 0.034 0.043 0.062 0.102 0.120 0.190 0.270 0.370 0.416 0.462 0.602 0.789 0.990 Every effort has been taken to ensure that the data listed in this catalogue is correct. Challenge accepts no liability for any inaccuracies or damage caused. All dimensions in millimetres unless otherwise stated. 361 14. Bearings Section.indd 361 16/10/2008 16:48:23
Bearings 6300 & 6800 Series 6300 & 6800 Series 6300 & 6800 Series Shape Dimension Bearing Number Basic Load Rating kN Bore d O.d D Width B Chamfer r min Dynamic cr 6300 6301 6302 6303 6304 6305 6306 6307 6308 6309 10 12 15 17 20 25 30 35 40 45 35 37 42 47 52 62 72 80 90 100 11 12 13 14 15 17 19 21 23 25 0.6 1.0 1.0 1.0 1.1 1.1 1.1 1.5 1.5 1.5 7.65 9.72 11.50 10.68 12.25 17.25 21.66 25.68 31.36 52.80 6310 50 110 27 2.0 6311 55 120 29 2.0 6312 60 130 31 6313 65 140 685 686 687 688 689 6800 6801 6802 6803 6804 6805 5 6 7 8 9 10 12 15 17 20 25 11 13 14 16 17 19 21 24 26 32 37 Static Cor Max Runout Speed rev/min Ball Complement Weight kg Grease Oil Quantity Size 3.480 5.080 5.420 6.660 7.790 11.37 14.80 17.542 22.25 31.70 20000 17000 16000 15000 13000 10000 9000 8000 7000 5600 26000 22000 20000 19000 17000 14000 12000 10000 9000 6700 6 6 7 7 7 7 8 8 8 7.144 7.938 7.938 8.731 9.525 11.500 12.000 13.494 15.081 61.80 37.90 5000 5800 1.070 71.50 44.60 4400 5300 1.370 2.1 81.80 51.90 4200 5000 1.730 33 2.1 92.70 59.70 4000 4600 2.080 3 3.5 3.5 4 4 5 5 5 5 7 7 0.15 0.15 0.15 0.2 0.2 0.3 0.3 0.3 0.3 0.3 0.3 35000 33000 31000 29000 28000 26000 22000 20000 19000 17000 15000 45000 42000 40000 38000 36000 34000 30000 28000 26000 22000 19000 6300 Series 0.054 0.058 0.082 0.110 0.140 0.220 0.330 0.410 0.600 0.814 6800 Series All dimensions in millimetres unless otherwise stated. 0.547 0.331 0.898 1.378 1.378 1.40 1.40 1.92 2.18 3.45 3.70 0.253 0.400 0.458 0.711 0.711 0.75 0.90 1.18 1.28 2.25 2.65 9 8 9 9 9 11 12 14 15 14 16 1.588 2.000 2.000 2.381 2.381 2.000 2.381 2.381 2.381 3.175 3.175 0.0011 0.0019 0.0021 0.0031 0.0032 0.005 0.007 0.008 0.019 0.042 0.048 Every effort has been taken to ensure that the data listed in this catalogue is correct. Challenge accepts no liability for any inaccuracies or damage caused. 362 14. Bearings Section.indd 362 16/10/2008 16:48:23
Bearings 6900 & 1600 Series UCFX 6900 00 &41600 Hole Series Flange Units 6900 & 1600 Series Shape Dimension Bearing Number Basic Load Rating kN Bore d O.d D Width B Chamfer r min Dynamic cr 5 6 7 8 9 10 12 15 17 20 25 30 13 15 17 19 20 22 24 28 30 37 42 47 4 5 5 6 6 6 6 7 7 9 9 9 0.2 0.2 0.3 0.3 0.3 0.3 0.3 0 3 0.3 0.3 0.3 1.08 1.48 2.02 2.25 3.30 3.30 3.38 4.00 4.30 6.55 7.05 7.25 Static Cor Max Runout Speed rev/min Ball Complement Grease Oil Quantity Size Weight kg 34000 32000 30000 28000 25000 25000 20000 19000 18000 17000 14000 12000 43000 40000 38000 36000 34000 32000 28000 26000 24000 22000 18000 16000 8 8 9 7 9 12 9 10 11 11 13 14 2.000 2.381 2.381 3.500 2.381 2.381 3.500 3.969 3.969 4.763 4.763 3.175 0.0024 0.0038 0.0052 0.0073 0.0082 0.009 0.011 0.016 0.018 0.036 0.042 0.048 28000 24000 22000 18000 15000 13000 11000 32000 28000 26000 20000 18000 15000 13000 8 9 10 11 12 12 14 4.763 4.763 4.763 4.763 5.556 6.35 6.35 0.019 1.025 0.027 0.050 0.060 0.085 0.100 6900 Series 695 696 697 698 699 6900 6901 6902 6903 6904 6905 6906 0.42 0.60 0.80 0.92 1.40 1.40 1.48 2.02 2.32 3.60 4.55 5.00 1600 Series 16001 16002 16003 16004 16005 16006 16007 12 15 17 20 25 30 35 28 32 35 42 47 55 62 7 8 8 8 8 9 9 0.3 0.3 0.3 0.3 0.3 0.3 0.3 5.08 5.60 6.82 7.90 8.42 11.2 11.5 2.38 2.55 3.38 4.45 5.15 6.25 8.80 Every effort has been taken to ensure that the data listed in this catalogue is correct. Challenge accepts no liability for any inaccuracies or damage caused. All dimensions in millimetres unless otherwise stated. 363 14. Bearings Section.indd 363 16/10/2008 16:48:24
Bearings R Series UCFL 200 R2Series Hole Flange Units R Series Shape Dimension Bearing Number Basic Load Rating kN Bore d O.d D Width B Chamfer r min Dynamic cr 4.763 6.35 6.35 6.35 6.35 9.525 9.525 12.70 12.70 15.875 19.05 22.225 25.4 28.575 31.75 34.925 38.1 12.70 9.525 12.70 15.875 19.05 22.225 22.225 28.575 28.575 34.925 41.275 47.625 50.80 53.975 57.15 63.5 66.675 3.967 3.175 3.175 4.978 5.556 5.556 7.142 6.350 9.535 7.142 7.938 9.525 9.525 12.7 12.7 14.2875 14.2900 0.3 0.1 0.15 0.30 0.40 0.40 0.40 0.40 0.40 0.60 0.60 0.60 0.60 0.7874 0.7874 0.7874 0.7874 0.89 0.27 0.83 1.136 2.175 2.56 2.56 3.93 3.93 4.62 7.24 7.74 7.74 8.237 8.606 - Static Cor Max Runout Speed rev/min Grease Ball Complement Oil Quantity Size Weight kg 136 370 558 1163 1350 1350 2230 2230 2790 4463 4960 5160 - 0.0006 0.0016 0.0044 0.0110 0.0140 0.0140 0.0150 0.0150 0.0280 0.0430 0.0430 0.0710 0.085 0.094 - 2.381 3.175 3.969 3.969 3.969 4.763 4.763 5.953 5.953 6.747 7.938 7.938 9.525 11.1125 12.000 12.000 0.0015 0.0032 0.0048 0.0075 0.012 0.017 0.019 0.028 0.034 0.043 0.062 0.102 0.120 0.190 0.270 0.370 0.416 R Series R3 R168 R188 R4 R4A R6 R6ZZ R8 R8ZZ R10 R12 Rl4 R16 R18 R20 R22 R24 All dimensions in millimetres unless otherwise stated. 0.42 0.14 0.37 0.558 1.163 1.35 1.35 2.23 2.23 2.79 4.46 4.96 5.16 5.179 6.472 - 268 830 1136 2175 2560 2560 3930 3930 4620 7240 7740 7740 - Every effort has been taken to ensure that the data listed in this catalogue is correct. Challenge accepts no liability for any inaccuracies or damage caused. 364 14. Bearings Section.indd 364 16/10/2008 16:48:24
Bearings Metric Taper Bearings Metric Taper Bearings Bearing Number d D T B C 30203 32203 30303 32004 30204 30304 32204 32304 32005 30205 30305 32205 32305 32006 30206 30306 32206 32306 32007 30207 33206 30307 32207 32307 32008 30208 33207 30308 32208 32308 32009 30209 33208 17 17 17 20 20 20 20 20 25 25 25 25 25 30 30 30 30 30 35 35 30 35 35 35 40 40 35 40 40 40 45 45 40 40 40 47 42 47 52 47 52 47 52 62 52 62 55 62 72 62 72 62 72 62 80 72 80 68 80 72 90 80 90 75 85 80 13.25 17.25 15.25 15.00 15.25 16.25 19.25 22.25 15.00 16.25 18.25 19.25 25.25 17.00 17.25 20.75 21.27 28.75 18.00 18.25 25.00 22.75 24.25 32.75 19.00 19.75 28.00 25.25 24.75 35.25 20.00 20.75 32.00 12 16 14 15 14 15 18 21 15 15 17 18 24 17 16 19 20 27 18 17 25 21 23 31 19 18 28 23 23 33 20 19 32 11 14 12 12 12 13 15 18 11.5 13 15 16 20 13 14 16 17 23 14 15 19.5 18 19 25 14.5 16 22 20 19 27 15.5 16 25 Mass kg 0.08 0.10 0.13 0.11 0.13 0.18 0.17 0.25 0.12 0.16 0.27 0.18 0.38 0.17 0.22 0.45 0.28 0.59 0.23 0.32 0.35 0.53 0.43 0.83 0.29 0.43 0.59 0.77 0.56 1.2 0.33 0.5 0.74 Bearing Number d D T B C 30309 32209 32309 32010 30210 33209 30310 32210 32310 32011 30211 33210 30311 32211 32311 32012 30212 30312 32212 32312 32013 33113 30213 32213 32313 32014 32214 32215 32216 45 45 45 50 50 45 50 50 50 55 55 50 55 55 55 60 60 60 60 60 65 65 65 65 65 70 70 75 80 100 85 100 80 90 85 110 90 110 90 100 90 120 100 120 95 110 130 110 130 100 110 120 120 140 110 125 130 140 27.25 24.75 38.25 20.00 21.75 32.00 29.25 24.75 42.25 23.00 22.75 32.00 31.50 26.75 45.50 23.00 23.75 33.50 29.75 48.50 23.00 34.00 24.75 32.75 51.00 25.00 33.25 33.25 35.25 25 23 36 20 20 32 27 23 40 23 21 32 29 25 43 23 22 31 28 46 23 34 23 31 48 25 31 21 33 22 19 30 15.5 17 25 23 19 33 17.5 18 24.5 25 21 35 17.5 19 26 24 37 17.5 26.5 20 27 39 19 27 27 28 Mass kg 0.96 0.57 1.5 0.42 0.54 0.79 1.3 0.6 1.9 0.58 0.7 0.85 1.8 1.21 2.55 0.63 0.92 2.1 1.14 3.15 0.62 0.62 1.1 1.59 3.82 0.97 1.7 1.93 2.18 Every effort has been taken to ensure that the data listed in this catalogue is correct. Challenge accepts no liability for any inaccuracies or damage caused. All dimensions in millimetres unless otherwise stated. 365 14. Bearings Section.indd 365 16/10/2008 16:48:25
Bearings Imperial Taper Bearings Imperial Taper Bearings Bearing Number d D T B C Mass kg 11749/11710 17.46 39.88 13.84 14.61 10.67 0.083 09067/09195 19.05 45.24 16.64 15.49 12.07 0.180 11949/11910 19.05 45.24 15.49 16.64 12.07 0.125 12649/12610 21.43 50.01 17.53 18.23 13.97 0.172 44643/44610 25.40 50.29 14.22 14.73 10.67 0.118 84548/84510 25.40 57.15 19.43 19.43 14.73 0.254 44649/44610 26.99 50.29 14.22 14.73 10.67 0.108 45449/45410 29.00 50.29 14.73 14.22 10.67 0.104 86649/86610 30.16 64.29 21.43 21.43 16.67 0.339 15123/15245 31.75 62.00 18.16 19.05 14.29 0.237 2580/2523 31.75 69.85 25.36 23.81 19.05 0.451 67048/67010 31.75 59.93 15.88 11.81 16.76 0.186 48548/48510 34.93 65.09 18.03 18.29 13.97 0.259 88649/88610 34.93 72.23 25.40 25.40 19.84 0.483 68149/68110 35.00 59.13 15.88 16.76 11.94 0.173 68149/68111 35.00 59.98 15.88 16.76 11.94 0.174 29748/29710 38.10 65.09 18.03 18.29 13.97 0.233 29749/29710 38.10 65.09 18.03 18.29 13.97 0.236 18590/18520 41.28 73.03 16.67 17.46 12.70 0.288 501349/501310 41.28 73.43 19.56 19.81 14.73 0.337 25580/25520 44.45 82.93 23.81 25.40 19.05 0.558 25580/25522 44.45 83.06 23.81 25.40 19.05 0.553 102949/102910 45.24 73.43 19.56 19.81 15.75 0.316 25590/25520 45.62 82.93 23.81 25.40 19.05 0.538 104948/104910 50.00 82.00 21.50 21.50 17.00 0.419 3780/3720 50.80 93.26 30.16 30.30 23.81 0.854 506849/506810 55.00 90.00 23.00 23.00 18.50 0.558 All dimensions in millimetres unless otherwise stated. Every effort has been taken to ensure that the data listed in this catalogue is correct. Challenge accepts no liability for any inaccuracies or damage caused. 366 14. Bearings Section.indd 366 16/10/2008 16:48:25
Bearings Notes Every effort has been taken to ensure that the data listed in this catalogue is correct. Challenge accepts no liability for any inaccuracies or damage caused. All dimensions in millimetres unless otherwise stated. 367 14. Bearings Section.indd 367 16/10/2008 16:48:25
Challenge Group Companies SCANDINAVIA Challenge Scandinavia AS Postboks 93 Kalbakken 0902 Oslo Norway Tel: 47 2216 5805 Fax: 47 2333 6117 Email: scsales@challengept.com AUSTRALIA Challenge Power Transmission (Aust) Pty Ltd B11, Scoresby Industrial Park Janine Street Scoresby Victoria 3179 Australia Tel: 61 3 9763 6701 Fax: 61 3 9764 0890 Email: aussales@challengept.com CHINA (Shijiazhuang) Challenge Power Transmission (SHZ) Plc South of Daxizhang High Technology Developing Area Shijiazhuang 050035 China Tel: 86 311-85385510 Fax: 86 311 8538 5590 Email: cnsales@challengept.com CZECH REPUBLIC Challenge PT (Czech) s.r.o Skopalikova 2600/47 76701 Kromeriz Czech Republic Tel: 420 573 334 106 Fax: 420 573 330 556 Email: czsales@challengept.com SOUTH AFRICA Challenge Power Transmission Africa (Pty) Ltd PO Box 30182 Jet Park 1469 Gauteng Republic of South Africa Tel: 27 11 3976115 Fax: 27 11 3978494 Email: sasales@challengept.com GERMANY Challenge Power Transmission GmbH In der Neuwies 1 D-35745 Herborn Germany Tel: 49 2772 575860 Fax: 49 2772 5758620 Email: desales@challengept.com IRELAND Challenge Power Transmission (Ireland) Ltd Unit 202 Holly Road Western Industrial Estate Dublin 12 Eire Tel: 353 1 4566311 Fax: 353 1 4566312 Email: ireland@challengept.com UNITED KINGDOM Challenge Power Transmission Plc Merryhills Enterprise Park Park Lane Wolverhampton WV10 9TJ United Kingdom Tel: 44 1902 866116 Fax: 44 1902 866117 Email: uk@challengept.com MALAYSIA Challenge Power Transmission (M) Sdn Bhd No. 3 Jalan PJU 3/50 Sunway Damansara 47810 Petaling Jaya Selangor Darul Ehsan Malaysia Tel: 603 7804 0407 Fax: 603 7804 4407 Email: mysales@challengept.com CHINA (Zhuji) Challenge Power Transmission (Zhuji) Plc 30 West Wangyun Road Zhuji Zhejiang 311800 China Tel: 86 575 8710 1617 Fax: 86 575 8710 1816 Email: cnsales@challengept.com NIGERIA Challenge Products Nigeria Ltd Plot 24 Kudirat Abiloa Way Ikeja Lagos Nigeria Tel: 01 791 5071 Fax: 01 497 2985 Email: ngsales@challengept.com 368 14. Bearings Section.indd 368 16/10/2008 16:48:26 TC
CHALLENGE WORLDWIDE PLC AND GROUP OF COMPANIES TERMS OF SALE These Terms do not apply if you deal as a Consumer Your statutory rights are not affected by these conditions 1. DEFINITIONS 5. In these Terms of Sale the following meanings shall apply: “We” and “Us” means CHALLENGE WORLDWIDE Plc “You” “the Goods” means the person seeking to purchase Goods from Us. means the goods or where the context permits the services to be supplied by Us. “Company Signatory” means a person authorised by Us. DELIVERY 5.1 Delivery will be effected when the Goods leave our premises whether carried by Us or an independent carrier or the premises of our suppliers when the Goods are delivered direct from suppliers. 5.2 Delivery dates are given in good faith but are estimates only. 5.3 Time for delivery shall not be of the essence of the Contract. 5.4 For the avoidance of doubt and without detracting from any other provisions of these Terms We shall not be liable for any damages whatsoever whether direct or indirect (including for the avoidance of doubt any liability to any third party) resulting from any delay in delivery of the Goods or failure to deliver the Goods in a reasonable time whether such delay or failure is caused by our negligence or otherwise howsoever. “the Terms” means the terms set out in this document and special terms agreed in writing between a Company Signatory and You or on Buyer’s order. “the Contract” means the contract for the supply of Goods incorporating these Terms. “Consumer” means any natural person acting for purposes outside their trade, business or profession. “the Defect” means the condition and/or any attribute of the Goods and/or any other circumstances which but for the effect of these Terms would have entitled You to damages. 5.6 The price agreed includes our normal delivery charges but We may make an additional charge if We incur further costs or expense such as (but not limited to) those caused by delivery of less than a full load; complying with your request for delivery outside our normal delivery pattern or trading hours or by instalments; orders of small value which are not economical for us to deliver free. 2.1 All orders are accepted by Us only under these Terms and they may no be altered other than with the written agreement of a Company Signatory. Any contrary or additional terms unless so agreed are excluded. 5.7 You must provide the necessary labour for unloading the Goods and unloading is to be completed with reasonable speed. If our delivery vehicle is kept waiting for an unreasonable time or is obliged to return without completing delivery or if We provide additional staff to unload Goods an additional charge will be made. 2. THE CONTRACT 2,2 Quotations are invitations to treat only. 2.3 Orders may be cancelled only with the written agreement of a Company Signatory and You will indemnify Us against all costs claims losses or expenses incurred as a result of that cancellation. 2.4 You shall be responsible to Us for ensuring the accuracy of the terms of any order including any applicable design drawing or specification provided to Us by You and for giving Us any necessary information relating to the Goods within a sufficient time to enable Us to perform the Contract in accordance with its Terms. 2.5 .1 It is Your responsibility to be fully conversant with the nature and performance of the Goods, including any harmful effects their use may have. 2.5.2 Without prejudice to Clause 2.5.4 of these Terms while We take every precaution in the preparation of our catalogues technical circulars price lists and other literature these documents are for your general guidance only and statements included in these documents (in the absence of fraud on our part) shall not constitute representations by Us and We shall not be bound by them. 2.5.3 We undertakes to comply with the Safety Legislation including, but not limited to the provision of any available information relating to the safety of the Goods to secure so far as reasonable practicable the health and safety of the users of the Goods. 2.5.4 You will comply with the Safety Legislation and agrees to indemnify and keep indemnified Us against Your failure to comply with the Safety Legislation. In particular, You shall indemnify Us against any and all claims or proceedings resulting from any injury, loss or damage caused by a failure to use the Goods in accordance with Our instructions whether such failure is on the part of the Your employees, contractors or agents or a third party to whom You have supplied the Goods. 2.5.5 We shall not be liable in respect of any misrepresentation made by Us our employees or agents to You your employees or agents as to the condition of the Goods their fitness for any purpose or as to quantity or measurements unless the representation is: 2.5.5.1 made or confirmed in writing by a Company Signatory; and/or 2.5.5.2 fraudulent 2.5.6 For the avoidance of doubt our liability for damages for misrepresentation (other than fraudulent) is excluded or limited by Clause 8 of these Terms. 3. PRICE 3.1 The price of the Goods shall be as published in our price list current at the date of delivery of the Goods. The price is exclusive of VAT which shall be due at the rate ruling on the date of a VAT invoice. 3.2 Prices listed or quoted are based on costs prevailing at the time when they are g
Shell Shell Dolium R petroleum grease -40 to 150 Good corrosion resistance and water resistance Alvania 2 Mineral grease -35 to 120 Long life and wide range of . noise, good low temperature resistance Jvania R Grease 2 (EP) Mineral grease -10 to 110 Good water resistance Dupont Krytox 240 AC (Mill-G 277617) Fiuorinated grease -35 to 290 High .
5 - BEARINGS Ball Bearings, Plain pgs. 5-8 & 5-10 Precision Ball Bearings, Plain pg. 5-6 Precision Ball Bearings, Flanged pg. 5-7 Ball Bearings, Flanged pg. 5-9 Nonmetallic Ball Bearings pg. 5-11 Hydro-Dynamic Pressure Bearings 5-13 Linear Ball Bearings, Closed Type pgs. 5-14 & 5-15 Frelon Lined Linear Bearings, Self-Lubricating pg. 5-22
(RCT bearings), ball screw support bearings, turntable bearings, as well as rectilinear motion bearings (linear ball bearings, linear roller bearings and linear flat roller bearings). A-5 Outerring Inner ring Cage Ball Deep groove ball bearing Fig 1.1 Ball Cage Outer ring Inner ring Angular contact ball bearing Fig. 1.2 Inner ring Outer ring .
Pump Bearings enable variability to save CO2. Bearing Solutions for Engine Needle Roller Bearings Thrust Needle Roller Bearings Planetary Gear Bearings One Way Clutches, e.g. for Oil-Pump Ball Bearings for Transmission Tandem Ball Bearings (TBB) Tapered Roller Bearings (TRB) Ball Bearing Cartridge for Turbocharger
NB (NIHON BEARING) NIHON PILLOW BLOCK SEIZO (FYH) NIHON SKF NIHON TOKUSHU BEARING NMB (MINEBEA/KEIAISHA) NSK (NIHON SEIKO) NTN OILES KOGYO OZAK SEIKO SANKYO OILLESS KOGYO TOK BEARING Bearings Bushings Bearings Spacers Bearings Bearings Bearings Bearings Beari
Clearance control . Shaft diameter [mm] Ball bearings Roller bearings Machining tolerances Radial . Rapid runup of the bearings to operating speed results in great- er temperature . P66 EL to define low vibration (noise) bearings. For cylindrical roller bearings we use a SQ1 specification
1. Inspection of rejected bearings before regrind. 2. Inspection of reworked bearings after regrind. 3. Endurance testing of new and reground bearings to verify performance. These bearings, part numbers 1-300-015-04 and 1-300-015-02, are radial contact bearings manufactured by Fafnir and New Departure. These bearings are interchange-
{Spherical Roller Bearings {Cylindrical Roller Bearings {Tapered Roller Bearings {Thrust Roller Bearings {Housed Unit Bearings {Ball Bearings {Couplings {Chain DOWNLOAD. Once you have selected a CAD file, download and insert it into your solution.
PEAJ 4435,2 - Vestas V90 - 2 MW Turbine one planetary stage, two helical stages excluding carrier bearings: all bearings are journal bearings bronze -tin and aluminum tin alloys used specific load radial bearings: 11,5.21 MPa specific load thrust bearings: 1,5 .2 MPa In House Test Performing
