BOXLIGHT XD-9m - Projectors, Projector Reviews, LCD .
USER’S GUIDEBOXLIGHTXD-9mDirect Phone :USA and Canada: 800-762-5757Outside the US: (360) 779-790119332 Powder Hill PlacePoulsbo, WA 98370-7407 USAwww.boxlight.com
Copyright 2000 by BoxlightPoulsbo, Washington. All rights reserved.
FCC WarningThis equipment has been tested and found to comply with the limits for a Class Adigital device, pursuant to part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference when the equipmentis operated in a commercial environment. This equipment generates, uses, andcan radiate radio frequency energy and, if not installed and used in accordancewith the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interferenceat his own expense.CanadaThis Class A digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.Safety CertificationsUL, CUL, TÜV, NOMEN 55022 WarningThis is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be required to take adequate measures. The typical use is in a conference room, meeting room or auditorium.
Declaration of ConformityManufacturer: Boxlight19332 Powder Hill Place, Poulsbo, Washington, USAWe declare under our sole responsibility that the XD-9m projector conforms to thefollowing directives and norms:Directive 89/336/EEC, Amended by 93/68/EECEMI: EN 55022 (1992) Class AEMC: EN 50082-1 (1992)IEC 801-2, IEC 801-3, IEC 801-4Directive 73/23/EEC, Amended by 93/68/EECSafety: EN 60950: 1992 A1 A2 A3 A4: 1997May, 2000TrademarksApple, Macintosh, and PowerBook are trademarks or registered trademarks ofApple Computer, Inc. IBM and PS/2 are trademarks or registered trademarks ofInternational Business Machines, Inc. Microsoft, PowerPoint, and Windows aretrademarks or registered trademarks of Microsoft Corporation. Digital Light Processing is a trademark or registered trademark of Texas Instruments.
TABLE OF CONTENTSSafety InstructionsiiiIntroductionImage ResolutionCompatibilityUnpacking the ProjectorUsage GuidelinesIf You Need AssistanceWarranty1111344Setting up the ProjectorConnecting a ComputerConnecting a Video PlayerPowering up the Projector and Adjusting the ImageTurning Off the Projector5791112Using the ProjectorBasic Image AdjustmentUsing the Remote ControlAdjusting the ProjectorUsing the Keypad and Remote ButtonsUsing the On-Screen MenusDisplay MenuAudio MenuImage MenuControls MenuLanguage MenuStatus Menu131313151618192021242626Maintenance & TroubleshootingCleaning the LensReplacing the Projection LampReplacing the Batteries in the Remote ControlUsing the Security LockTroubleshooting292929323233i
T ortable and Laptop Activation ChartUsing Video Mirroring with a PowerBook ComputerProjected Image Size373738404546Index47
SAFETY INSTRUCTIONSPlease read and follow all safety instructions provided BEFOREusing your new projector. Failure to comply with safety instructions may result in fire, electrical shock, or personal injury andmay damage or impair protection provided by equipment. Pleasesave all safety instructions.Safety Definitions: Warning: Statements identify conditions or practices thatcould result in personal injury. Caution: Statements identify conditions or practices that couldresult in damage to your equipment.Safety Symbols:Attention: For information about usage of a feature, pleaserefer to the User’s Guide.Warning: Hot surface. Do not touch.An arrow pointing to the lamp door on the projector.Safety Terms: Warning: Don’t look directly into the lens when the lamp isturned on. Warning: To replace the lamp, turn the projector off byunplugging the power cord. To avoid burns, wait 30minutes before opening the lamp door. Follow all instructionsprovided in this User’s Guide. Warning: Please use the power cord provided. Connectthe power cord to a receptacle with a protective safety(earth) ground terminal. Warning: Refer all service to qualified service personnel. Ser-vicing your own projector will void the warranty. See the following page for the customer service contact information. Caution: Don’t block ventilation openings.iii
SafetyInstructions Caution: Don’t set liquids on the projector. Spilled liquids maydamage your projector. Caution: Don’t place the projector on a hot surface or in directsunlight. Caution: Do not drop the projector. Transport the projector in aBoxlight-approved case; see page 39 for a list of cases.Important Operating ConsiderationsDo not place the projector on a tablecloth or other soft coveringthat may block the vents. In the unlikely event of the bulb rupturing, thoroughly clean the area behind the projector and discardany edible items placed in that area.t (.2f)6mDo not place objects inthis area behind the projectorCustomer ServiceIf you need assistance, call Boxlight at 1-800-762-5757 or360-779-7901.iv
INTRODUCTIONThe Boxlight XD-9m is specifically designed for the mobile presenter. It packs XGA 1024x768 graphics with 16.7 million colorsinto a small, 4.8 pound package. It generates crisp, clear imagesusing Digital Light Processing (DLP) technology, and featuresan M1-DA connector for easy, built-in digital/analog and USBconnectivity. The projector is easy to connect, easy to use, easy totransport, and easy to maintain.Image ResolutionThe XGA resolution of the XD-9m’s projected image is 1024x768.The projector cannot compress screen resolutions above1024x768. If your computer’s screen resolution is higher than1024x768, reset it to a lower resolution before you connect theprojector.NOTE: The XD-9m automaticallyexpands 640x480 and 800x600images to 1024x768. You can display these images at their nativeresolutions by turning off the AutoCompatibilityResize feature. See “Resize” onThe projector is compatible with a wide variety of computers andvideo devices, including:page 21 for more information. IBM-compatible computers, including laptops, up to 1024x768resolution. Apple Macintosh and PowerBook computers up to1024x768 resolution. Most standard VCRs, DVD players, HDTV sources, camcord-ers and laser disc players.Unpacking the ProjectorNOTE: The projector is compatible with 1080i HDTV format.The projector comes with the items shown in Figure 1. Check tomake sure all are included. Contact Boxlight immediately ifanything is missing.If you are experienced in setting up presentation systems, use theQuick Start card that was included in the shipping box. For complete details on connecting and operating the projector, refer tothis User’s Guide.1
IntroductionNOTE: The contents of your21shipping box may vary dependingon the projector configurationyou’ve ordered.3459678FIGURE 1Shipping box contents21.XD-9m projector lens cap6.M1-DA analog computer cable2.Soft carry case7.Audio cable adapter3.User’s Guide and Quick Startcard8.Audio cable4.Power cord9.Composite video cable5.Remote control
speakerkeypadzoom ringSecurity lockfocus ringconnector panelpowercordconnectorFIGURE 2Side view of projectorUsage Guidelines Do not look directly into the projection lens when the lamp isturned on. The bright light may harm your eyes. Do not block the grills on the projector. Restricting the air flowcan cause it to overheat and turn off. If this happens, you mustwait a minute before attempting to turn it back on. Handle the projector as you would any product with glasscomponents. Be especially careful not to drop it. Avoid leaving the projector in direct sunlight or extreme coldfor extended periods of time. If this happens, allow it to reachroom temperature before use. Transport the projector in a vendor-approved hard or soft case.3
IntroductionIf You Need AssistanceThe first place to look for help is in this manual. Be sure to checkthe guidelines in “Troubleshooting” on page 33.If this manual doesn’t answer your question, call Boxlight at1-800-762-5757 or 360-779-7901.WarrantyThis product is backed by a limited two-year warranty. Thedetails of the warranty are printed at the back of this manual.4
SETTING UP THE PROJECTOR1 Place the projector on a flat surface. The projector must be within 10 feet (3 m) of your powersource and within 6 feet (1.8 m) of your computer. If you want to project from behind a translucent screen, setup the projector behind your screen. See “Rear Projection”on page 24 to reverse the image.2 Position the projector the desired distance from the screen. The distance from the lens of the projector to the screen andthe zoom setting determine the size of the projected image.Figure 3 shows three projected image sizes. For more information about image size, see “Projected Image Size” onpage 46.013f t.7.8ft.3.2f t.5 ft.12 ft.20 ft.FIGURE 3Projected image size at minimum zoom3 Make sure the projector is unplugged and your computer isturned off.5
SettinguptheProjectorNOTE: Before you continue,make sure the projector isunplugged and your equipment isturned off. If you’re connecting aincomputer, make sure the distanceinbetween it and the projector is 6feet or less.S-videocompositevideoAudio inM1-DAdata interfaceFIGURE 4Connector panelto USB mouseto computer videoto computerFIGURE 5M1-DA analog computer cable6to projector
Connecting a ComputerThe projector ships with an M1-DA analog computer cable. Ifyour computer has a digital output, you can order the optionalM1-DA digital computer cable. See “Optional Accessories” onpage 39.1 Plug theinto theend of the M1-DA analog computer cableconnector on the projector.end of the M1-DA analog computer cable into2 Plug thethe video connector on your computer.NOTE: Many laptop computersdo not automatically turn on theirexternal video port when a secondary display device such as aininprojector is connected. Refer toyour computer manual for thecommand that activates the exter-audio cablenal video port. Activation commands for some laptop computersM1-DA analog computer cableare listed in the Appendix of thisUSB mousemanual on page 40 and in theFIGURE 6Service section of our website.Connecting the projector to a computerNOTE: If you are connecting anolder Macintosh computer thatdoes not have a 15-pin connector,you must use a Mac adaptorbetween the computer and theprojector. See “Optional Accessories” on page 39.7
SettinguptheProjectorDo you want to control the computer’s mouse from the projector’sremote or keypad?NOTE: The USB mouse isend of the M1-DA analog computer cable1 Plug theinto the mouse connector on your computer.supported for use withWindows 98, Windows 2000, andApple OS 8.5 and higher only.NOTE: You do not need to restartDo you want to play your computer’s audio on the projector?1 Plug either end of the audio cable into the audio connector onyour computer.2 Plug the other end of the audio cable into theon the projector.connectoryour computer after connecting aUSB mouse to use it (it is hotpluggable).8Now you’re ready to power up the projector and your laptop.Skip to “Powering up the Projector and Adjusting the Image” onpage 11.
Connecting a Video Player1 If your video player uses a round, one-prong composite videoconnector, you’ll need only the audio cable, audio adapter,and composite video cable that shipped with the projector. If your video player uses a round, four-prong S-video con-nector, you’ll need an S-video cable in addition to the audiocable and audio adapter. The S-video cable is sold separately. (See “Optional Accessories” on page 39.)NOTE: HDTV sources are connected to the projector using theM1-DA computer cable. See the2 Plug the composite video cable’s yellow connector into the“video-out” connector on your video player (Figure 7). Thisconnector may be labeled “To Monitor.”previous pages for details. If you’re using an S-video cable, connect it to the “S-videoout” connector on the video player (Figure 8).3 Plug the other yellow connector into the composite video connectoron the projector. If you’re using S-video, plug the other end of the cable intothe “S-video” connectoron the projector (Figure 8).ininaudioadaptercomposite videocableaudio cableFIGURE 7Connecting the projector to a video player using the standard video cable (with composite video connector) and the audio cable and adapter9
udio cableFIGURE 8Connecting the projector to a video player using an S-video cable and the audio cableand adapterNOTE: The audio adapter isprovided so that the same audio4 Plug the audio adapter’s white connector into the left “audioout” connector on your video player. Plug the adapter’s redconnector into the right “audio out” connector on the videoplayer (Figure 7 and Figure 8).cable used to connect a computercan be used with the adapter toconnect a VCR.CAUTION: Your video playermay also have a “Video Out”connector for a coaxial cableconnection. DO NOT use this toconnect to the projector.105 Plug the audio adapter’s other end into the audio cable.6 Plug the audio cable into the “audio in”projector.connector on theThe projector is compatible with these major broadcast videostandards: NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, PAL-60, andSECAM. It automatically adjusts to optimize its performance forthe incoming video. The input signal for SECAM video is similarto other video signals and cannot be automatically detected,therefore SECAM must be chosen manually. See “Video Standard” on page 24 for details.
Powering up the Projector and Adjusting the Image1 Remove the lens cap.2 Plug the power cord into the side of the projector, then plug itinto your electrical outlet. A surge-protected power strip isrecommended.NOTE: Always use the power cordthat shipped with the projector. The fans start to run, and the Lamp LED on the top of theprojector (Figure 12 on page 16) lights orange until the software has initialized. When initialization is complete, theLamp LED lights green. A green Lamp LED indicates thatyou can press the lamp on/off button to turn the lamp onand off.3 Turn on the lamp by pressing the lamp on/off buttononthe keypad (see Figure 12 on page 16).NOTE: The first time you connect The startup screen appears.your computer to the projector, the4 If you connected a video player, turn it on.computer may display a messagestating that new hardware was The video image should display on the projection screen. Ifa computer source is active, press the source button on thekeypad (page 16) or the video button on the remote to dis-play your video image. You can select a default source todetermine which source the projector examines first duringpower-up for active video; see “Default Source” on page 25.found. The Add New HardwareWizard may appear. Use the Wizard to load the correct driver (thecomputer considers the projector aPlug and Play Monitor). Use the volume buttons to adjust the volume.5 Turn on your computer. The computer image should display on the projectionscreen. If a video source is active, press the source button onthe keypad or the computer button on the remote to displayyour computer’s image. Make sure your laptop’s externalvideo port is activated; see “Portable and Laptop ActivationChart” on page 40 for details.NOTE: With some computers,the order in which you power upthe equipment is very important.Most computers should be turned If necessary, make adjustments to the image using the pro-on last, after all other peripheralsjector’s on-screen menus. To open the menus, press themenu button on the keypad or remote, then select the Display or Image sub-menu. For more information about themenus, see page 18.have been turned on. Refer to yourcomputer’s documentation todetermine the correct order.11
SettinguptheProjectorTurning Off the ProjectorIf you want to turn off the projector for a short period of time,press the standby button on the keypad or remote. This blanks thescreen for fifteen minutes, but keeps the projector running. (Youcan change the amount of time the projector stays in standbymode; see “Standby Time” on page 24 for details.) After 15 minutes, the lamp goes out (the projector keeps running). To exitstandby mode, press the standby button again. (It may take several seconds for the projection lamp to reach full power andproject the image again.)NOTE: Lamp life will be extendedif you turn the lamp off, then wait1 minute while the lamp coolsbefore unplugging the projector.The Lamp LED will light greenwhen the lamp has cooled. Seepage 16 for details on the LampLED.12To completely power off the projector, unplug it. If you want toturn the lamp back on immediately, you must allow about aminute for the lamp to cool. The lamp won’t light if it’s too hot.
USING THE PROJECTORThis section describes how to use and make adjustments to theprojector. It also provides a reference to the keypad and remotebuttons and the options available from the on-screen menus.Basic Image Adjustment1 Make sure you have powered up your equipment in the rightorder (page 11).2 If the image doesn’t display completely, zoom the image(page 15), adjust the height of the projector (page 15) or centerthe image by adjusting its horizontal or vertical position(page 23). Be sure the projector is at a 90 degree angle to thescreen.3 If the image is out of focus, rotate the focus lens (page 15).4 If the image appears to shimmer or if it has blurry verticalbars after you have adjusted the focus, turn Auto Image(page 21) off and then back on to reset the automatic sync andtracking. If that doesn’t clear up the image, turn Auto Imageoff and adjust the sync (page 22) and/or the tracking(page 22) manually.5 If the colors don’t look right, adjust the brightness (page 19).Using the Remote ControlThe projector ships with a remote that has four function buttons,a disk mouse and two mouse buttons, one on the top of theremote and one on the bottom.Point the remote control at the projection screen or at the front ofthe projector. The range for optimum operation is about 25 feet. Ifyou point the remote at the projection screen, the distance to thescreen and back to the projector must be less than or equal to 25feet. For best results, point the remote directly at the projector.NOTE: To control the computer’smouse from the projector’s remoteor keypad, you must connect themouse connector on the computercable to the computer. See page 8for details.13
UsingtheProjectordisk mouseright mouse buttonleft mouse button(on underside of remote)FIGURE 9Remote controlNOTE: If the remote is inactivefor several minutes, it “sleeps” toconserve battery life. Press anybutton except the disk mouse tore-activate the remote.Press anywhere on the edge of the disk mouse to move the cursoron the screen. You can move the cursor at any angle by pressingthe corresponding edge of the disk. The mouse button on the topof the remote simulates your computer’s right mouse button; thebutton on the bottom simulates your computer’s left mouse button. See “Using the Keypad and Remote Buttons” starting onpage 16 for a description of the four function buttons.If you are creating presentations in Microsoft PowerPoint , youcan use the remote’s mouse buttons to navigate through yourpresentation while in Slide Show mode. To configure PowerPointfor this, choose Options from the Tools menu, click the View Tab,de-select the “Popup Menu on Right Mouse Click” option in theSlide Show section, then click OK. Then, when you’re in PowerPoint’s Slide Show mode, a left click advances to the next slideand a right click returns to the previous slide (other PowerPointmodes are not affected).14
Adjusting the ProjectorTo focus the image, rotate the focus ring (Figure 10) until theimage is clear. To zoom the image, rotate the zoom ring. Thisadjusts the image size without affecting focus.zoom ringfocus ringFIGURE 10Focus ring and zoom ringThe projector is equipped with a self-locking, quick-release elevator foot and button (Figure 11).To raise the projector:1 Press and hold the elevator button (Figure 11).2 Raise the projector to the height you want, then release thebutton to lock the elevator foot into position.elevator footelevator button(under finger)FIGURE 11Adjusting the height of the projector15
UsingtheProjectorUsing the Keypad and Remote ButtonsWhile the menus are displayed, the volume, source, and standbybuttons on the keypad act as menu navigation buttons. See“Using the On-Screen Menus” on page 18 for details.lamp LEDFIGURE 12Keypad and remote buttonsLamp on/off (keypad only)Press the lamp on/off button to turn the lamp on or off. The LampLED indicates the state of the lamp. A green Lamp LED indicatesthat you can turn the lamp on, or the lamp is currently on. Anorange LED indicates the software is initializing or the lamp iscooling. Do not press the lamp on/off button when the LED isorange.MenuPress the menu button to open the on-screen menus. Press menuagain to close the menus. When you close the menus, the projector saves any changes you made. For more information about theon-screen menus, see page 18.Source (keypad only)or Computer and Video (remote only)When you have more than one source (computer and video) connected to the projector, select between them by pressing thesource button on the keypad or the computer or video button onthe remote.16
StandbyWhen you press standby, the display and audio turn off and ablank screen is displayed for 15 minutes. You can change theamount of time the projector stays in standby mode; see“Standby Time” on page 24 for details. If you press standby again within 15 minutes, the projectorreturns to normal operations immediately. If you press standby again after 15 minutes, there is about a60 second delay before the lamp turns back on. If you don’t press standby again, the lamp turns off after 15minutes.Volume (keypad only)To increase the volume, press volume ume, press volume -. To decrease the vol-.Volume adjustments are saved for each source you have connected.17
UsingtheProjectorUsing the On-Screen MenusThe projector has six drop-down menus that allow you to makeimage adjustments and change a variety of settings. Most of theseadjustments aren’t available directly from the keypad.NOTE: Some menu items may begrayed out at certain times. Thisindicates the item is not applicableto your setup (for example, videostandards do not apply toTo open the on-screen menus, press the menu button on thekeypad or remote. This changes the volume, source, and standbybuttons on the keypad to menu navigation buttons. Press thecorresponding buttons to move the cursor up, down, left, orright, or use the disk mouse on the remote. To select a menu,move the cursor left or right to highlight the menu you want. Thedrop-down menu appears.computer sources) or the item isnot enabled until another selection is made (for example, ManualTracking is not available until AutoImage is turned off).Display AudioBrightnessContrastTintColorSharpnessBlank screenReset allImageControlsLanguageStatusblueuse these buttons to navigate throughthe menusFIGURE 13Keypad navigation buttons and drop-down menuTo change a menu setting, use the up and down navigation buttons on the keypad or the disk mouse on the remote to move thecursor up and down to the item you want to change (the selecteditem is highlighted), then use the left and right navigation buttons to adjust a setting. Some submenus, such as Brightness, consist of a slider bar you use to increase or decrease a value; somesubmenus, such as Standby Time, consist of options you scrollthrough to select the desired one. All changes are saved whenyou close the menus.To access another menu, use the up and down navigation buttonsor the disk mouse to move back to the top of the current menu,then use the left and right navigation buttons to move to anothermenu.18
Display Menu Display AudioBrightnessContrastTintColorSharpnessBlank screenReset allImageControlsLanguageStatusblueFIGURE 14Display menuBrightnessAdjusting the brightness changes the intensity of the image. Press the left navigation button to darken the image. Press the right navigation button to lighten the image.ContrastThe contrast controls the degree of difference between the lightestand darkest parts of the picture. Adjusting the contrast changesthe amount of black and white in the image. Press the left navigation button to decrease the contrast. Press the right navigation button to increase the contrast, mak-ing the blacks appear blacker and the whites appear whiter.TintThe tint adjusts the red-green color balance in the projectedimage. Changing the Tint setting has no effect on PAL or SECAMvideo sources. Press the left navigation button to increase the amount of greenin the image. Press the right navigation button to increase the amount of redin the image.19
UsingtheProjectorColorThe color setting adjusts a video image from black and white tofully saturated color. This setting is not available for computerimages. Press the left mouse button to decrease the amount of color inthe image. Press the right mouse button to increase the amount of color inthe image.SharpnessThis setting adjusts the sharpness of a video image. Press the left mouse button to decrease the sharpness. Press the right mouse button to increase the sharpness.Blank ScreenBlank Screen determines what color is displayed when there is noactive source and when the projector is in standby. Click the leftor right navigation button to toggle between blue and black.Reset AllClick the left or right navigation button to reset all the options(except Language, Video Standard, Rear Projection, and StandbyTime) in all the menus to their original settings.Audio MenuDisplay Audio ImageVolumeControlsLanguageStatusFIGURE 15Audio menuVolume Press the left navigation button to decrease the volume.NOTE: Changing the volumeusing the menu is the same aschanging it using the keypad.20 Press the right navigation button to increase the volume.Volume adjustments you make are saved for each source.
Image MenuDisplayAudio Image ControlsLanguageKeystoneOverscanAuto imageResizeManual syncManual trackingHorizontal positionVertical positionStatusonononFIGURE 16Image menuKeystoneThis option helps to keep the image square as the angle of projection is changed. To adjust the keystone, highlight Keystone, thenclick the right navigation button. This option is available for computer sources only.OverscanThis option crops all the edges of the image to remove noise generated on the edges by your source. This option is available forvideo sources only.NOTE: Some screen savers interfere with the operation of AutoImage. If you’re experiencing prob-Auto ImageThe projector automatically adjusts tracking, signal synchronization and vertical and horizontal position for most computers(Auto Image does not apply to video sources). If you want toadjust these features manually, you must turn off Auto Image firstby highlighting Auto Image in the Image menu and clicking theleft or right navigation button to select “off”.lems, try turning your screen saveroff, then turning Auto Image offand back on.ResizeThis option works differently for computer and video sources.For computer sources, Resize automatically resizes the image byscaling it up or down. It only affects computer images that are notthe projector’s native resolution. When Resize is on, the projectormakes the best fit of the image to the computer screen. If you turnResize off (by highlighting it in the Image menu and clicking theleft or right navigation button to select “off”), the image may beeither cropped or too small for the screen.NOTE: When you connect anHDTV source, the projector automatically displays the image in16x9 format.21
UsingtheProjectorFor video sources, Resize allows you to select from among fourdifferent re-sizing options. The default is Standard, which resizesthe image from its original version to fit a standard 4x3 aspectratio screen. Widescreen Letterbox preserves the 16x9 aspect ratioof the original theater version, but the image is placed in a 4x3space, so black bars appear at the top and bottom of the image.Enhanced Widescreen also preserves the aspect ratio of the original theater version and is designed to be used with content that isEnhanced for Widescreen TVs. This option yields more detailthan Widescreen Letterbox. Native reduces the Standard size tomatch the height of Enhanced Widescreen.Manual SyncThe projector adjusts signal synchronization automatically formost computers. But if the projected computer image looks fuzzyor streaked, try turning Auto Image off then back on again. If theimage still looks bad, try adjusting the signal synchronizationmanually:1 Turn Auto Image off.2 Highlight Manual sync, then press the left or right navigationbutton repeatedly until the image is sharp and free of streaks.Manual TrackingThe projector adjusts tracking automatically to match the videosignal from your computer. However, if the display shows evenlyspaced, fuzzy, vertical lines or if the projected image is too wideor too narrow for the screen, try turning Auto Image off then backon again. If the image is still bad, try adjusting the tracking manually:1 Turn Auto Image off.NOTE: The Manual Sync,Manual Tracking, Horiz.Position and Vert. Positionoptions are available only forcomputer sources. The projectorsets these options automaticallyfor video sources.222 Highlight Manual tracking, then press the left or right navigation button repeatedly until the fuzzy vertical bars are gone.
Horizontal positionFollow these steps to manually adjust the horizontal position:1 Turn Auto Image off.2 Highlight Horizontal position, then press the left navigationbutton to move the image right or press the right navigationbutton to move the image left.Positioning adjustments are saved when y
The projector cannot compress screen resolutions above 1024x768. If your computer’s screen resolution is higher than 1024x768, reset it to a lower resolution before you connect the projector. Compatibility The projector is compatible with
ALLIN1-980 Universal projector mount 168.00 25.00% 126.00 VP-CGUPM06-S Vantage Point universal projector mount, silver 127.00 25.00% 95.25 WALLMOUNT-U60 60" wall arm with universal projector mount, with gear adjustments 332.00 25.00% 249.00 WALLMOUNT-U 49" (up to) short-throw wall mount includes universal projector
Have spare projector bulbs on hand & follow projector manufacturer's guidelines on projector cleaning & maintenance. - Mark H. @ Zion Clear Lake Level the projector horizontally as the first adjustment to aiming (assuming that the projector is sitting direct on from the screen on the horizontal plane). Minimal keystoning should be done.
The PolyVision Driver Projector Add-in runs in the background whenever your computer is on. Configuring the PolyVision Driver Projector Add-in The ēno one whiteboard can interact with the PolyVision projector when you configure the PolyVision Driver Projector Add-in to identify the computer port where the projector is connected.
manual. WARNING! MERCURY HAZARD. This projector’s bulb contains a small amount of mercury. If the lamp breaks, adequately ventilate the area where the breakage occurred. The projector bulb may require special handling and disposal at end-of-life. Protecting Your Projector Do: Connect projector’s cables before turning the projector ON.
Refer to these sections to learn more about your projector and this manual. Projector Features Notations Used in the Documentation Where to Go for Additional Information Additional Projector Software and Manuals Projector Part Locations Projector Features The Home Cinema 3200 and 3800 pr
Many projector lenses are not centered on the chassis of the projector. Ensure that the centerline of the lens is aligned perpendicular to the center of the screen. Position the lift offset the same distance as the offset of the projector lens. If your projector
the following sections. The basic workflow for projecting through a network is: 1. Set up a wired or wireless network for the projector. See "Setting up a wired network for the projector" on page 6 or "Setting up a wireless network for the projector" on page 8 for details. 2. Connect your computer or mobile device to the projector.
Animal nutrition, with emphasis on dairy cows. Submitted by Alimuddin Naseri, Afghanistan: alimuddin.naseri@akdn-afg.org Page 6 Phosphorus (P) P is used in bone formation, in close association with Ca and vit.D. In addition, P has more known functions in the animal body than any other mineral element. Deficiency symptoms
