NiTRO 1000 Manual Version 1.9.1 -1-
NiTRO 1000 Manual Version 1.9.1-1-
Contents.Before You Begin. 5Important Safeguards and Warnings.Introduction.67System Overview. 8Main System.Front Panel.Rear Panel.comrad 8101113Installation. 15Ten Steps for InstallersSuggested System Locations.Mounting the System.Recommended Location for Record LED.Routing the Power Harness.Routing the Camera Harness(es).Routing the Sensor Harness.Installing the Dome Camera.Recommended Camera Locations.Check For:Quick Configuration Settings for Installers.1516161819192021242425Setting the Configuration. 26Basic Configuration.Advanced Configuration.System Configuration.263038Recording. 43Start Recording.Stop Recording.4343Playback from Recorder. 44Playback Methods.44System Shutdown. . 48Downloading Video. . 49comrad Only to Computer (Recommended).Connecting the Recorder to a Computer.Recorder to Local Area Network (LAN).comrad Only to Computer.Manually Installing MAXVIEW .Connecting the Recorder to Computer WITH USB Ethernet Adapter.Browsing the Recorder on a Computer.-2-49495050515153
Contact Information.Information.Recorder to Local Area Network (LAN).54MAXVIEW . .55PC Requirements.Installation.Connect comrad to Computer via USB:Operation.Opening Video Files.GPS.Using The GPS Zoom Feature.Using The Scrubber.Time Graph Selection.Using The Calendar Feature.Audio Controls.Displaying Sensors.Drag and Drop a Video File.Mark & Save a Video Clip.Extracting Still Image.Setting the Recorder Configuration.Saving Configuration.Loading Configuration on Recorder.Check for Updates.GSI – Canada301-31127 Wheel AvenueAbbotsford, BC V2T 6H1CanadaGSI – USA446 Harrison StreetSumas, WA 98295USASales & TechnicalTechnical SupportNorth America:Tel: 1.604.864.6187Fax: 71Upgrading Software on the NiTRO 1000. .74Troubleshooting. 75Appendix. .76Toll Free: 1.888.666.4833Setting The System IDMain Power Harness.Sensor Harness Cable (CAB000145)767677Warranty.80Contact Information. .82Document Revision:October 1 2010 - Version 1.9.1 - DN2195 Manual NiTRO 1000st- 82 --3-
Table of Figures.Figure 1: Front Panel.10Figure 2: Rear Panel.11Figure 3: Power Input – Pin-outs.12Figure 4: Sensor Input – Pin-outs. .12Figure 5: comrad - Front and Rear Panels. .13Figure 6: comrad Extraction.13Figure 7: Recommended System Locations .16Figure 8: IR20, Camera Location and Wiring. .17Figure 9: Alarm Button/Record LED Splice.18Figure 10: Ceiling Mounting the Camera.22Figure 11: Focusing The Camera .22Figure 12: Changing Camera Lens .23Figure 13: Three Camera Configuration. .24Figure 14: Four Camera Configuration.24Figure 15: Alternate Four Camera Configuration. .24Figure 16: Table of Available Frame Rates.35Figure 17: Cloning a comrad . .42Figure 18: Record Screen.43Figure 19: Stop Screen.43Figure 20: Playback Display. .45Figure 21: Mark and Save. .46Figure 22: Downloading Clips.47Figure 23: Manually Installing MAXVIEW .51Figure 24: Browsing The Recorder On A Computer.53Figure 25: Recorder To Local Area Network. .54Figure 26: MAXVIEW Operation. .59Figure 27: Composite of Map; Satellite and Hybrid Views. .60Figure 28: Displaying The GPS Map. .60Figure 29: Displaying The GPS Vehicle Locator. .60Figure 30: Calendar Feature.62Figure 31: Mark and Save Clips.64Figure 32: Save Video Clip Options Window. .65Figure 33: Upgrading Software. .74-4-the required repairs or replacements and no claim ofbreach of warranty shall be cause for cancellation orrescission of the contract of sale. Proof of purchasecomplete with the serial numbers of the productspurchased will be required by the customer tosubstantiate any warranty claim. All warranty workmust be performed by an authorized GatekeeperSystems service representative.This warranty does not cover any Gatekeeper Systems’product that has been subject to misuse, neglect,negligence, or accident, or that has been operated in anyway contrary to the operating instructions as specifiedby Gatekeeper Systems either verbally, in writing, byinstructions written on the product or in the GatekeeperSystems Installation and Operating Manual. Thiswarranty does not apply to any damage to theGatekeeper Systems product that is the result ofimproper maintenance or to any Gatekeeper Systems’product that has been altered or modified so as toadversely affect the products’ operation, performanceor durability or that has been altered or modified so asto change its intended use.USA RECEIVING FACILITY:Gatekeeper Systems Inc.446 Harrison StreetSumas WA 98295Tel. 1.604.864.6187Fax 1.604.864.8490Toll Free (N.A.) 1.888.666.4833verified the Company will issue a return materialauthorization number (RMA) authorizing the purchaserto return faulty merchandise to the Company for repairor replacement as determined by the Company. It maybe necessary for the customer to assist GatekeeperSystems in assessing failed product. GatekeeperSystems may require the customer to removehardware, manipulate software and/or performother diagnostic activities. Failure to assist in and allowremote diagnostic activities may result in a service feebeing charged.Advance replacements will be issued for the first 45days from the date of shipment.This Warranty applies to all Company productsmanufactured by Gatekeeper Systems and soldin the United States and Canada.This warranty gives you specific legal rights, and youmay also have other rights which vary from state tostate.CANADA OPERATIONS:Gatekeeper Systems Inc.301-3 1127 Wheel AvenueAbbotsford BC V2T 6H1Tel. 1.604.864.6187Fax. 1.604.864.8490Toll Free (N.A.) 1.888.666.4833-81-
Before You Begin.Begin.Warranty.Warranty.In this document, important information is displayed using the following symbols:Customer Limited WarrantyAlerts the reader that not adhering to the instruction could resultin bodily harm, equipment damage or data lossGATEKEEPER SYSTEMS INC. (Company) warrants thatany product manufactured or supplied by GatekeeperSystems and found in the reasonable judgment ofGatekeeper Systems to be defective in material orworkmanship will be repaired or replaced by GatekeeperSystems without charge for parts and labor.Gatekeeper Systems’ is not responsible for lost ormissing video.This warranty shall cover the following periods andequipment:The warranty does not extend to repairs madenecessary by normal wear or by the use of parts oraccessories which are either incompatible with theCompany product or adversely affect its operation,performance or durability.Camcorder SystemCameras - 1 yearBattery Adapters - 1 yearPlates & Enclosure Boxes - lifetimeGatekeeper Systems reserves the right to change orimprove the design of any Company product withoutassuming any obligation to modify any productpreviously manufactured.Gatekeeper SystemInterior Cameras - 5 yearsExterior Cameras - 3 yearsVCR - 1 yearGSX-900 / 1000 Digital Recorder - 1yearNiTRO-900 / 1000 Digital Recorder – 5 years (harddrives limited to 3 years)Nitro 401 and Nitro 404 Digital Recorder – 3yearsKingston SDHC Memory Card – LifetimeAll Accessories - 1 yearALL IMPLIED WARRANTIES ARE LIMITED IN DURATIONTO THE SPECIFIED PERIOD FOR EACH PRODUCTCATEGORY AS LISTED IN THIS DOCUMENT.ACCORDINGLY, ANY SUCH IMPLIED WARRANTIESINCLUDING MERCHANTABILITY, FITNESS FOR APARTICULAR PURPOSE, OR OTHERWISE, AREDISCLAIMED IN THEIR ENTIRETY AFTER THEEXPIRATION OF THE APPROPRIATE WARRANTYPERIOD. GATEKEEPER SYSTEMS’ OBLIGATION UNDERTHIS WARRANTY IS STRICTLY AND EXCLUSIVELYLIMITED TO THE REPAIR OR REPLACEMENT OFDEFECTIVE PARTS, AND GATEKEEPER SYSTEMSDOES NOT ASSUME OR AUTHORIZE ANYONE TOASSUME FOR THEM ANY OTHER OBLIGATION.The warranty periods commence on the date ofshipment. During the period of the warranty the Company,at its discretion will repair and/or replace all improperlyfunctioning equipment caused by a manufacturer’sdefect. This warranty does not protect againstaccidental or intentional damage, vehicle electricalsystems generating steady state or transients, voltagesor currents exceeding product specification, loss, acts ofnature, water damage, or any other event that did notoriginate during the manufacturer of the product. DVR’smust be returned once every twelve months for serviceotherwise warranty may be void.The Gatekeeper Systems product including any defectivepart must be returned to Gatekeeper Systems withinthe warranty period. The expense of deliveringCompany product to Gatekeeper Systems for warrantywork will be paid by the customer. The expense ofdelivering Company product back to the customer willbe paid by Gatekeeper Systems. Gatekeeper Systems’responsibility in respect to claims is limited to makingAlerts the reader to a strong recommendation that will enhancethe performance of the recorderA useful suggestion or tip for the advantage of the readerAlerts the reader to refer to a section of the manual that will aidin further explanation of the topic at handGATEKEEPER SYSTEMS ASSUMES NO RESPONSIBILITYFOR INCIDENTAL, CONSEQUENTIAL OR OTHERDAMAGES INCLUDING, BUT NOT LIMITED TO THEEXPENSE OF RETURNING THE COMPANY PRODUCTTO GATEKEEPER SYSTEMS CORPORATE HEAD OFFICE,MECHANIC’S TRAVEL TIME, CUSTOMER LABOREXPENSES, TELEPHONE OR TELEGRAM CHARGES,RENTAL OF LIKE PRODUCT DURING THE TIMEWARRANTY SERVICE IS BEING PERFORMED, TRAVEL,LOSS OF USE OF THE PRODUCT, LOSS OF TIME ORINCONVENIENCE.Warranty ServiceTo obtain warranty service, the purchaser must notifythe Company during the warranty period. ThePurchaser will discuss the defect or problem with aCompany technician, and once the problem has been- 80 --5-
Important Safeguards and Warnings.Warnings.Remove Main Power Fuse Prior To Any Electrical Work Or Jump Starting TheBus.CAUTIONRISK OF ELECTRICSHOCK.DO NOT OPENConnect 12V constant directly to the battery.The NiTRO 1000 is intended for indoor use; keep away from water andmoisture.The NiTRO 1000 must be mounted more than two feet away from any two-wayradio equipment. Do not mount the NiTRO 1000 near a heat source and do notblock vents on the enclosure.Do not remove the comrad from the NiTRO 1000 system until the systemhas fully powered down. To ensure that the system has fully powered down, checkthat the comrad power light is off.The NiTRO System is incompatible with GSX System. Do not plug the GSXcomrad to the front of the NiTRO System or plug the NiTRO comrad tothe front of the GSX System either physically or by USB.Do not remove the cover of the NiTRO 1000. Doing so will directly result invoiding the manufacturer’s warranty. If your NiTRO 1000 requires repair,contact Gatekeeper Systems Inc. (GSI) at 1.888.666.4833.The NiTRO System power negative cable should be connected to a solid chassisgrounding area, or negative post of battery.All unused cables, sensor/indicator wires should be individually insulated, tied offand protected from touching ground. Unused NiTRO cabling should never begrounded.-6--79-
Introduction.Introduction.Notes.Congratulations on your purchase of the NiTRO 1000 Digital Smart Recorder fromGatekeeper Systems Inc. Prior to installing or using the NiTRO 1000, please read thismanual in its entirety in order to fully understand the correct procedures for installation,setup and operation of the system.The NiTRO 1000 Digital Smart Recorder has been designed specifically to be a userfriendly and cost-effective replacement for conventional VHS analog recorders currently usedin the industry.The NiTRO 1000 is a 4 channel digital video recorder that records all four channelssimultaneously; this ensures all critical data is captured. Navigation through user menus ismade simple through the use of the front panel mounted LCD screen which also eliminatesthe need for a PC interface during setup. The NiTRO 1000 Digital Smart Recorder is asimple and efficient method of managing video onboard your school buses.The advanced digital recording technology of the NiTRO 1000 eliminates the need for tapemanagement and replacement while offering: - 78 -comrad portable, vandal resistant hard drive and storage deviceIsolation Suspension SystemThermal Intelligence Direct Connect USB 2.0Alarm Button VerificationLCD Smart Search User-friendly and convenient way to find important images andclipsProprietary video management MAXVIEW Video Management System.Substantial storage capability without compromising video qualityAccelerated download speedsUser friendly, intuitive design for easy operation and administrationPlus many more features-7-
System Overview.Overview.Check List.Use the provided check list to ensure that you have received all the components required foryour complete NiTRO 1000 Digital Smart Recorder.Main System.System.NiTRO 1000 Digital Smart RecorderNiTRO Mounting PlateGSX-N1000Control/GSX-N1000comrad XXX(color may vary from that of illustration)GSX-NBSPSYSNiTRO End CapsGSX-NRDOOR / GSX-NFDOORWLDome Camera(s)CAMICAGSCX.X.XCamera GasketSensor HarnessSensor Harness Cable (CAB000145)The Sensor Harness Cable is made up of three separate inner-core cables; A Trigger (7 wires); BAlarm & LED (4 wires); C Speed (3 wires)A. Trigger Sensor Harness.1. Red. Connect to accessory 12V . Providesignition to Digital Video Recorder. DO Notconnect to noise suppression circuit, connectto true Ignition source.2. Yellow. Connect to Stop Arm (8 way) circuit12V 3. Blue. User customizable sensor (optional)12V 4. Green. User customizable sensor (optional)12V 5. Orange. Connect to Brake light circuit 12V .6. Brown. User customizable sensor (optional) 12V 7. White. Connect to Warning light (Amber) circuit, 12V .B. Alarm & LED Harness (4 wires):1. Red. 12V output from unit. Connect to Red wires from Alarm Button and Record LED. DoNot hook-up to 12V Input signal.2. Green. Connect to White wire from Record LED.3. Black. Connect to Black wire from Alarm button.4. White. (Optional), connect to 12V Driver Alarm Buzzer or Light AccessoryCAB0000145Power HarnessCAB000139Camera HarnessC. Speed Sensor Harness (3 wires), Not required with GPS.1. Green. Connect to Speed Pulse. (See transmission or ABS electrical manual for your vehicle.2. Red. Output from Digital Video Recorder, (Only to be used with Speedometer InterfaceModules)3. Black. Ground Signal ( - ) from Digital Video Recorder. (Only to be used with SpeedometerInterface Modules)GSWHC2N-XXIf you have failed to receive any of the above parts please contact your dealer or GSI directly at1.888.666.4833.-8--77-
Appendix.Setting The System IDOnce the system has booted and is in Record mode,press the button directly below either the Right or Leftpointing arrow until you see Configuration. Press theGO button.Cycle through the options until you see Basic listed,Press the GO button.There are two optional download packages that are available to customize your NiTRO 1000 system.Use the below check list to ensure you have received the appropriate parts for your kit. NiTRO comrad Connect KitGSX-NTR-DPBK-Basic Kit Dual-Head USB CableDVRUSBN-GB-MIX NiTRO comrad Power SupplyDVRPWRN 3A-125WU05NiTRO comrad Connect KitGSX-NTR-DPBK-Basic KitCamera Alignment CableCAB000157Cycle through these options until you see Set ID, Pressthe GO button.Clear the long serial number from the screen bypressing the ‘-‘ button. To change a character use the and – buttons to cycle through until you see thecharacter you require. Use the Left and Right arrowbutton to advance or go back. Repeat this sequenceuntil you have the desired name. To create a spacecycle through the characters until the end of all thelower case letters.Once the ID has been set, press the BLUE menu buttonto the left of the LCD.NiTRO Installation and Setup KitGSX-NTR-DPAK-Intermediate Kit DC to DC Cable RCA Single patch Cable Direct Camera Connect iescessoriesThe following accessories are available for the NiTRO 1000 Digital Smart Recorder .Once the BLUE menu button has been pressed you willsee the screen change to Saving Config.A confirmation screen will appear stating Config Saved.Continue through the BASIC menu to change andconfirm all parameters you need.Main Power Harness.The Main Power Harness Cable contains two wiresA Negative Wire.For details on installation refer to individual instruction sheets enclosed with eachaccessory. NiTRO - Desktop Power Supply NiTRO – Alarm Button NiTRO - Record LED IR Illuminator NiTRO GPS (Build Option) IR Quick ConnectB Positive Wire.Please ensure Main Power Cable is hooked up before any battery cut-off or isolation circuits.A. Hook the Black wire directly to the Negative BatteryTerminal.B. Connect the RED wire directly to the Positive BatteryTerminal. Ensure that the 10 AMP fuse is in-linebetween the Red wire and the Positive BatteryTerminal.NOTE: The 15 AMP Fuse must be pulled when jump starting the bus battery, or, when doingelectrical work. Failure to comply with these instructions may result in the warranty being voided.- 76 --9-
Front Panel.Panel.Troubleshooting.Troubleshooting.When I turn on the Bus, my recorder won’t power up or my recorder powers up and then shutsdown everyevery couple of minutes. Why is this? Ensure that the Sensor harness is connected correctlyEnsure the black Molex is connected to the back of the recorderEnsure comrad is properly inserted into the NiTRO Control unitMy camera shows an upside down image:image: The camera is meant to be mounted to the ceiling. If the camera is mounted right side up,or sideways, the preview will show an image that is rotated.Rotate the lens by removing the two large screws on the camera bracket, rotating thecamera bracket 180 and then screwing it back on.When I view video,video, there is only a black screen: Make sure all camera harnesses are connected to the video in ports on the back of therecorder and/or camera.If you have added or removed cameras and have not changed the configuration, you maynot be able to capture video.Figure 1: Front Panel.Panel.I have connected a monitor to my recorder, yet there is nothing on the screen of the monitor.Why?123456 78comrad comrad - Removable hard drive. DO NOT PULLPULL comrad comrad OUT WHILE SYSTEM IS RUNNING.Main Menu Button - Press to save settings, move up a menu level and move within menu.Smart LCD Display - Backlit for easy viewing.Menu Control Buttons - Easy navigation through menu.5VDC Out - Used to power up external NiTRO comrad with DC to DC Cable.USB A - Connect external comrad to USB port to download video files or connect USB toEthernet adaptor and crossover cable to connect PC or laptop.comrad comrad Temp LED - comrad temperature indicator.comrad comrad Power LED - comrad power status.If the monitor uses an S-video connector, the monitor needs to be connected to the unitprior to starting the unit.I have MAXVIEW MAXVIEW open and want to view a video file. How do I do this? Click on File Open.Using the drop down menu under “Look in”, locate NiTRO Videos.Double click on ‘videos’ folder (Select ‘clips’ folder if applicable).Select desired video file(s) to view by clicking with mouse to highlight and then press Open.The NiTRO System is not compatible with GSX System. Do not plug the GSXcomrad into the front of the NiTRO System or plug the NiTRO comrad intothe front of the GSX System either physically or by USB.- 10 --75-
Upgrading Software on the NiTRO NiTRO 1000.1000.Rear Panel.Panel.To upgrade each recorder, follow the instructions under “Check for Updates” above first todownload the upgrade files to a comrad . Once that is complete follow the instructions below. Plug in the comrad as an external drive.Any upgrades will be automatically copied to the NiTRO 1000. The LCD will display “CopyingUpgrades” for a moment.When the upgrade files are finished copying, shutdown and restart the recorder.To verify that the upgrade was successful, go to Configuration System S/W Versionand verify that the number is the same as the upgrade file downloaded.Dual Head USBCableSparecomradTMFigure 2: Rear Panel.Panel.comradDC – DC Cable.TMFigure 33:33: Upgrading Software.Ensure that the NiTRO System has a constant and stable power source. If power isremoved from the unit, secure stable power and repeat the o IN - 4 Molex camera and audio inputs. Audio is not recorded inputs 3 and 4.2 Pin Molex Connector - Power input.Mouse Input - Not Used.Keyboard - Connect keyboard to navigate through menus instead of menu control buttons.CRT (SVGA) - Connect computer monitor to view the menu display (alternate output)*.Ethernet Port - Used to connect recorder to Local Area Network (LAN).USB A - Connect external comrad to USB port to download video files or connect USB toEthernet adaptor and crossover cable to connect PC or laptop.S-Video Output - Connect TV to view the menu display (alternate output)*.Video Output - Connect TV to view the menu display (alternate output)*.Parallel Port - Not used.DBDB-9 Port (RS(RS-232) - Not used.Sensors - Connect sensor harness.AudioAudio OUT - RCA audio output can be connected to speakers.GPS AntennaAntenna (Build Option) - A GPS Antenna can be connected so that speed and position canbe recorded.Remote Panel (Build Option) - Remote Panel used for configuration.*All three outputs will display the same image with the menu display, any of the three can be used.- 74 --11-
PINDESCRIPTIONWIRE COLOR2GNDBlack112V MainRedThe NiTRO System powernegative cable should beconnected to a solidchassis grounding area.Figure 3: Power Input – PinPin-outs.outs. 8 9 10 11 12 13 141PIN12345678910111213**1423456 7WIREWIREWIRECOLORCOLORCOLORFUSE PANEL CONNECTIONXYZ3 Lead4 Lead7 LeadExtra 2, User DefinedBrownOptionalExtra 1, User DefinedGreenOptionalIgnition TriggerRedConnect to Accessory 12VSmart Flag AlarmBlackUse for Driver AlarmAlarm LEDWhiteOptionalGNDBlackNCExtra 3, User DefinedBlueOptionalWarning Light TriggerWhiteTo Warning Light CircuitBrake Light TriggerOrangeTo Brake Light CircuitStop Arm TriggerYellowTo Stop Arm CircuitRecord Light IndicatorGreenOptional12VDC Output**RedRedSpeed SensorGreenOptionalX - Speed Sensor Harness. Y - Alarm & LED Harness Z - Sensor HarnessDESCRIPTIONDESCRIPTIONFigure 4: Sensor Input – PinPin-outs.outs.(See Appendix page 78 / 79 for more information)* Never connect to ground.- 12 --73-comrad has beensuccessfully upgraded, youmay now update anothercomrad or use thiscomrad to copy upgradefiles to another recorder.Refer to the UpgradingSoftware on the NiTRO 1000 for details.
comrad comrad Files are automaticallydownloaded to your PC.Front Panel DiagramRear Panel DiagramFigure 5: comrad comrad - Front and Rear Panels.1. comrad - Removable hard drive2. comrad Power - Connect power source to comrad 3. Mini USB - Used to connect comrad to PC or externally to NiTRO 1000 as an externaldrive4. comrad Temp LED – Lit when the NiTRO system is out of temperature range5. comrad Power LED – Lit when the NiTRO system is powered up.Shutdown the NiTRO System prior to removal of the comrad . Do notremove the comrad while the comrad Power LED is illuminated. Upgrade files are automaticallycopied in to the upgrade folder onthe comrad .comrad comrad Extraction.Extraction.Figure 6: comrad comrad Extraction.Extraction.If the NiTRO System is running, turn system off and wait for the comrad LED togo out. Do not remove comrad while the NiTRO System is running.- 72 --13-
Pull firmly on the comrad to remove it.Check for UpdatesUpdates.tes.New software updates can be downloaded automatically through MAXVIEW . All softwareupdates are cumulative. The most recent software update for the recorder will incorporate anychanges introduced by previous versions.To insert comrad , ensure it is right side up and in line with the NiTRO 1000Control Unit. Firmly push on front of the comrad , ensure it is seated properly witha good connection at the back Ensure the NiTRO system is off while inserting the comrad - 14 --71-Make sure that the computerhas an internet connection.Do not start MAXVIEW manually (Using Desktop Icon).Plug the comrad into yourcomputer through the USBport. See comrad only toComputer section for moredetails. MAXVIEW willautomatically Open and startrunning.Choose File Check forUpdates.Press OK to download updatesto the comrad .
Network Configuration.Installa
The NiTRO 1000 is intended for indoor use; keep away from water and moisture. The NiTRO 1000 must be mounted more than two feet away from any two-way radio equipment. Do not mount the NiTRO 1000 near a heat source and do not block vents on the enclosure. Do not remove
Saving to Nitro Cloud Logging into Nitro Cloud through Nitro Pro gives you the added benefit of taking your workflow outside of your desktop, utilitizing the services Nitro Cloud offers How to save to Nitro Cloud 1 . Ensure that you are logged into Nitro Cloud, then Open a PDF file in Nitro
Thank you for purchasing the Traxxas Nitro Rustler. This man-ual contains the instructions you will need to operate, and main-tain your Nitro Rustler.Look over the manual and examine the Nitro Rustler carefully before running it.If for some reason you think the Nitro Rustler is not what you wanted, then do
9. Brake adjust screw 10. Repeat this process until the desired height Rear wheel unfolding the Nitro Rollator To unfold the Rollator, position the Nitro upright on all three wheels. Hold each hand grip and pull outward until the Nitro rollator unlocks and opens fully (figure 1-2)
The Walking aid is suitable for a single user with limited mobility. The nitro is ideal for indoor and outdoor use. 1. Bag 2. Back Rest 3. Operating Instructions introduction 7. Seat 8. Bag 9. Front wheel 10. Brake adjust screw 11. Rear wheel 12. Safety bow nitro includes: unfolding the nitro Position t
terminate enclaves. The Nitro CLI must be installed and used on the parent instance. For more information, see Nitro Enclaves Command Line Interface (p. 52). AWS Nitro Enclaves SDK The AWS Nitro Enclaves SDK is an open-source library that you can use to develop enclave applications,
Nitro Pro, from Nitro Software, is a popular PDF editing, markup and collaboration application for all industries. More information on Nitro Pro. Nitro Pro natively works with CoSign to digitally sign and certify PDF files. It also supports verification of digital signatures. Supported File TypesFile Size: 1MB
Cable Pack Sony Cable Pack P/Oly Cable Fuji. CAPTUR Compatibility Part No. 1000 710.0 1000 710.1 1000 710.4 1000 710.3 1000 710.2 1000 708.1 1000 708.3 1000 710.5 1000 710.6 1000 710.7 1000 711.0 1000 710.8 Range Up to 100m Up to 100m Up to 100m Up to 100m Up to 100m Up to 100m Up to 100m Up to 100m
uplifting tank and the plastic deformation of the bottom plate at the shell-to-bottom juncture in the event of earthquake, the design spectrum for sloshing in tanks, the design pressure for silos, and the design methods for the under-ground storage tanks as well. The body of the recommendation was completely translated into English but the translation of the commentary was limited to the .
