LIFTING SOLUTIONS - Jergens Inc
LIFTING SOLUTIONSCenter Pull Style. 484-485Envirolox Protective Finish. 494Eye Bolts.500Eye Nuts. 499Forged Center Pull.487–488Forged Center Pull Stainless Steel.486Kwik-Lok Lifting Pin.495–496Hold Down Clips. 494Installation Information. 481LIFT ID . 503Pivoting Lift Rings. 499Quality Standard Information. 502–503Shackle-Lok Hoist Rings.482-483Shoulder Eyebolts.500Side-Pull Style.489–490Side Swivel. 493SP 2000 Side-Pull Style. 491–492Swivel Eyebolts. 497–498LIF TING SOLUTIONSLifting Solutions479
LIFTING SOLUTIONSLIFTING SOLUTIONS GROUPEngineer The Lift!! Jergens recommends the use of swiveling and pivoting hoist rings. Conventional eye bolts should be used for straight vertical lifts only. Are you using the proper hoist ring for the application? Is the hoist ring free to swivel and pivot? Any movement restrictions? Are lifting hole(s) in the proper location? Do you have the correct hole size for the hardware - safe lift capacity? Are the holes tapped deep enough to assure full thread engagement?(See figure #3 on Installation Information; page 481.) Recommended thread depth:Steel – 1-1/2 times the bolt diameter (min.)Aluminum – 2 times the bolt diameter (min.) RULE OF THUMB, IF IN DOUBT – DON’T!!!Applied Load Changes With Sling AngleJergens swivelling hoist rings are designed and rated to be pulled at any angle at the rated load.However, the applied load on a multipoint lift will increase if the sling angle is less than 90 .So be sure to consider the sling angle when selecting lifting equipment. See illustration below.LIF TING SOLUTIONSSample Calculation:Sling Angle(Degrees)907560453015L applied load oneach leg of slingDO’SDON’TS1. Observe working load limitations (be especially carefulwith eyebolts used for angle lifts – see sling angle chart).1. Never pull a Center Pull Style hoist ring bar fromthe side.2. Visually inspect hoist ring prior to use.2. Never use an oversized hook in eyebolts or hoist rings(See figure #1 on Installation Information; page 481).3. Fully tighten hoist ring to recommended torque.Full thread engagement is required (no space betweenswivel bushing and lift).4. Assure proper thread depth - do not shim.5. Make sure hoist rings have free travel - it must swiveland pivot without restrictions.6. When installing in soft metal, such as aluminum, the minimum effective thread engagement should be two times thediameter of the thread (1-1/2 times bolt diameter – steel).480Applied Load(Pounds)1000104011551410200038603. Never use excessive sling angle.4. Never steam clean or degrease hoist rings(could cause rusting and binding).5. Never apply shock loads.6. Never allow the side of a hoist ring to make contactwith the lift. (See figure #2 on InstallationInformation; page 481.)Jergens, Inc. 15700 S. Waterloo Road Cleveland, Ohio 44110-3898 USA
INSTALLATION DATALIFTING SOLUTIONS GROUPNever use a hook or otherlifting device which will pryor tend to open the “U”shaped bar on Center-PullHoist Rings!Fig. 1After installation, check thehoist ring to be sure it swivels and pivots freely in alldirections. The side of thering must not contactanything!Fig. 2No EmptySpaceAlways ensure fullthread engagement wheninstalling hoist rings!Fig. 3Select the proper Hoist Ring for the job. Do not attempt to apply more thanthe rated load capacity. The load capacity is marked on the Hoist Ring.Drill and tap the workpiece so that the hoist ring bolt is installed perpendicularto the surface of the workpiece. Countersink the tapped hole to prevent“swelling” of the top thread when the hoist ring bolt is torqued. The workpiecesurface must be flat, providing complete contact for the hoist ring bushing.Do not use spacers between the hoist ring bushing and the workpiece surface.When installing in soft metal, such as aluminum, the minimum effective threadengagement should be two times the diameter of the thread. When installing insteel, thread engagement should be 1-1/2 times the thread diameter.Always tighten the bolt to the proper torque value, which is stamped on the HoistRing.Loosening of the bolt may develop during use. Re-tightening to the requiredtorque must be done whenever the bolt loosens. The proper tightening torqueis stamped on the Hoist Ring.When lifting, apply force gradually. DO NOT APPLY SHOCK LOADS.For through-hole applications, be sure that nut/washer are the same qualitygrade as the Hoist Ring.200020002000 lbs.LIF TING SOLUTIONS » INS TALL ATION DATAInstallation InformationDepending upon the slingangle, the applied loadmay be more than theweight being lifted. Twopoint lifting of a 2000pound weight, with a slingangle of 30 , will result inan applied load of 2000pounds to each hoist ring!oFig. 4Periodic visual inspection and pull testing is recommended as damagecan occur from improper usage.Phone: 800-537-4367 or 1 216-486-5540 Fax: 1 216-481-6193 E-mail: info@jergensinc.com www.jergensinc.com481
LIFTING SOLUTIONSLIFTING SOLUTIONS GROUPShackle-Lok Shackle-Style Hoist Rings Shackle-Lok combines the strength of a hoist ringwith the versatility of a shackle. Its unique, 3-piecedesign is ideal for use with a variety of lift methods,and shackles are interchangeable. Shackle-Lok issimply the industry’s most efficient below-the-hooklifting device from a weight to load rating ratio.Features & Benefits:LIF TING SOLUTIONS Internal ball bearings allow for smoothrotation under load Full 360 swivel and 180 pivot action Easy to remove shackle Rated 5:1 strength factor in vertical pull Material: alloy steel Bolt and base finish: black oxide Bolt and base are magnetic particle inspected Shackle finish: zinc plated with gold coloredconversion coating Proof tested to 200% of rated load capacity Certificate of proof test provided 3D Solid models available in multiple formatsfrom www.jergensinc.comConforms to: ASME B30.26 CE certified RR-C-271FCertified482Jergens, Inc. 15700 S. Waterloo Road Cleveland, Ohio 44110-3898 USA
LIFTING SOLUTIONSLIFTING SOLUTIONS GROUPShackle-Lok Shackle-Style Hoist Rings The Shackle-Lok was designed to work with numerousthread sizes. Any straight thread size, pitch, or length canbe manufactured to meet application needs. Note: When tightening the bolt, the shackle and pin must be removed.Not intended for prolonged 1-81-81 1/4-71 1/2-62-4 1/22 523.523.523.995.115.116.521/21/49/169/163/411 1/161 1/43/411 1/411 1/211 1/41 1/41 1/22 1/41 7/82 1/43 1/841WidthInsideShackleInsideShackle Pin HoleNoWithShackle DiameterSizeShackle Shackle Clearance to /41/41/21/21/21/21/21/21/25/85/87/87/87/87/87/811 1/21 1/21 ShackleNoShackleHex 3/43/412LIF TING SOLUTIONSLengthPart NumberStated load capacity based on recommended thread torques as shown in chart.It is recommended that these torques be used when installing hoist rings.2LengthPart 58NS24459NS24460NS24463NS24465NS24466NS24468NSM6 X 1.0M8 X 1.25M10 X 1.5M12 X 1.75M16 X 2.0M20 X 2.5M24 X 3.0M30 X 3.5M30 X 3.5M36 X 4.0M42 X 4.5M48 X 5.0M64 X 546888961WidthInsideInside ShackleShackle Pin HoleNoWithShackle DiameterSizeShackle Shackle Clearance to ex 4448810121414191919242All dimensions are in millimeters.Stated load capacity based on recommended thread torques as shown in chart.It is recommended that these torques be used when installing hoist rings.2Phone: 800-537-4367 or 1 216-486-5540 Fax: 1 216-481-6193 E-mail: info@jergensinc.com www.jergensinc.com483
LIFTING SOLUTIONSLIFTING SOLUTIONS GROUPCenter-Pull Traditional Style Full 360 Swivel and 180 Pivot Action Rated at 5:1 Strength Factor Material: Alloy Steel Finish: Black Oxide (Except Washer) U-Bar, Bolt, Pins, Base, Washer and Bushingare Magnetic Particle Inspected Washer: Zinc Plated with Gold Colored (Inch),Clear/Blue (Metric) Conversion Coating Proof Tested to 200% of Rated Load Capacity Certificate of Proof Test provided(See sample on page 501) 3D Solid Models available in multiple formats from www.jergensinc.com Available with Envirolox protective finish. See page 494for more informationTo add Lift ID to Hoist RingAdd “F” to the end of the partnumber Example: 23414F LIF TING SOLUTIONSBlack OxideStandard nvirolox Protected CoatingLong U-BarStandard U-BarLong rtNumberStdLongU-Bar ��—1/2.75.43.381.841 1/4.75.43.381.841 /16.75.43.381.841 /16.75.43.381.841 1 1/161.20.69.502.56 1 .7823511-E6.723/41.50.88.753.522 3/84 .7211.50.88.753.522 3/84 -E6.721 1/41.50.88.753.522 3/84 -E6.7211.50.88.753.522 1/44 5-E6.721 1/41.50.88.753.522 1/44 6-E6.723/41.50.88.753.522 1/44 7-E6.7211.50.88.753.522 23518-E6.721 1/21.50.88.753.522 E8.1112.311.401.005.142 3521-E8.111 1/22.311.401.005.142 223523-E8.1112.311.401.005.142 13/16 4 .111 1/42.311.401.005.142 13/16 4 E8.111 1/42.311.401.005.142 11/16 4 E8.111 1/22.311.401.005.142 11/16 4 E8.112 1/42.311.401.005.142 11/16 4 3/82307.51 1/4-715000234298.73——233298.73——1 7/83.191.751.256.504 1/4—470141 1/4-81500023429-088.73———8.73——1 7/83.191.751.256.504 1/4—470142343312.47——2333312.47——2 3/44.192.251.758.556 1/2—8003323433-08 12.47———12.47——2 3/44.192.251.758.556 1/2—800331 1/2-6240001 1/2-8240002-4 1/2300002-8300002 1/2-4500002 1/2-85000012.47——2333512.47——3 1/84.192.251.758.556—11003623435-08 12.4723435———12.47——3 ——45.7532.2511.728 1/4—21008923438-08 16.5023438———16.50——45.7532.2511.728 1/4—210089Stated load capacity based on recommended thread torques as shown in chart.It is recommended that these torques be used when installing hoist rings.Available from stock as Standard Clevis.Jergens, Inc. 15700 S. Waterloo Road Cleveland, Ohio 44110-3898 USA
LIFTING SOLUTIONSLIFTING SOLUTIONS GROUPCenter-Pull Traditional StyleMetricStandard x Protected CoatingLong U-BarStandard U-BarLong gthCDStdLongU-Bar U-Bar TorqueHH(kg m)Wt.(kg)0.172EFGM6 x 746.734.0–0.6M8 x .746.732.0–1.00.17M10 x .746.730.0–1.70.17M12 x 19.038.122.419.089.460.51083.81.1M16 x 9.038.122.419.089.456.51068.21.1M20 x 4.038.122.419.089.452.510113.61.2M20 x 2.058.735.625.4130.673.010113.63.0M24 x 7.058.735.625.4130.669.011131.03.1M30 x 531.7165.1107.4–60.06.3M30 x 531.7165.1107.4–60.06.4M36 x 4.0M42 x 4.5M48 x �–100.0100.0100.015.516.016.8M64 x 6.257.1297.6210.0–290.040.0All dimensions are in millimeters. Stated load capacity is based upon specific thread torques shown in chart.It is recommended that these torques be used when installing hoist rings. Available from stock as Standard Clevis.123Bolt Replacement Kits - Inch threadsBolt Replacement Kits - Metric threadsBlack Oxide Hoist RingsStd. U-Bar Long U-BarBolt KitPart No. Part No.Part No.Envirolox CoatedStd. U-Bar Long U-Bar Bolt KitPart No.Part No. Part No.23404 2360423304 23604-E2365523655-E.02234052360523305 23605-E23456236562335623656-E.02234062360623306 23606-E.0323458236582335823658-E.03234082360823308 102361023310 23610-E2341123611233112351123511-EKitWt.(lbs)Black Oxide Hoist RingsStd. U-Bar Long U-BarBolt KitPart No.Part No.Part No.Envirolox CoatedStd. U-Bar Long U-Bar Bolt KitPart No.Part No. Part 2362923329 23629-E23629-082.902363323333 23633-E3.5023633-083.502363523335 23635-E7.3023635-087.302363823338 23638-E15.6623638-08LIF TING SOLUTIONSBlack OxideBolt Kits contain bolt and retaining ring. See page 494 for Hoist Ring hold down clips.To add Lift ID to Hoist RingAdd “F” to the end of the partnumber Example: 23414F 15.96Phone: 800-537-4367 or 1 216-486-5540 Fax: 1 216-481-6193 E-mail: info@jergensinc.com www.jergensinc.com485
LIFTING SOLUTIONSLIFTING SOLUTIONS GROUPForged Center Pull - Stainless SteelOur new Forged Center Pull Hoist Ring integrates a solid center brace lift bail into our most popularstyle product. This design eliminates the possibility of spreading the lift ring in misapplications.Forged hoist rings are ideal for OEM and industrial use.U.S. Patent No. 6,652,012 Material: 17-4PH Full (over center) 360 swivel and 180 pivot action Capacities up to 5,000 lbs. Inch and metric 5:1 strength factor Same strength/load capacity as steel Proof tested to 200% of rated load capacity Maximum operating temperature 800 F Intermittent, 600 F continuous Made in U.S.A. 3D Solid Models available in multiple formats from www.jergensinc.comMTo add Lift ID to Hoist RingAdd “F” to the end of the partnumber Example: 23414F JHLIF TING SOLUTIONSØILLKKGCCBA Thread SizeDFERing BailInchLoadThreadHexPartCapacitySizeSize Torque 61/161/161/1615/325/89/163/411/16115/161 1/41 1/81 1/21/21/21/21/2111111111122222211111 1/21 1/21 1/21 1/21 1/21 1/41/41/43/43/43/43/43/43/411111/21/21/21/23333332 1/42 1/42 1/42 1/44 7/164 7/164 7/164 7/164 7/164 7/162 15/322 15/322 15/322 15/324444443 19/323 19/323 19/323 19/326 3/86 3/86 3/86 3/86 3/86 3/83/43/43/43/41 1/41 1/41 1/41 1/41 1/41 3.6MetricLoadThreadHexPartCapacitySizeSize Torque WeightNumber(kg)ABCDEFGHIJKLM(N 00450105019002150M8 X 1.25M10 X 1.5M12 X 1.75M16 X 2.0M20 X .425.450.850.850.825.4 8.725.4 8.738.1 14.338.1 14.338.1 12.7112.762.791.362.791.3101.6 161.9101.6 161.9101.6 161.91919323232Jergens, Inc. 15700 S. Waterloo Road Cleveland, Ohio 44110-3898 USA101737801340.270.271.641.641.7
LIFTING SOLUTIONSLIFTING SOLUTIONS GROUPForged Center PullOur new Forged Center Pull Hoist Ring integrates a solid center brace lift bail into our most popularstyle product. This design eliminates the possibility of spreading the lift ring in misapplications.Forged hoist rings are ideal for OEM and industrial use. Full (over center) 360 swivel and 180 pivot action Capacities up to 30,000 lbs. Inch and metric 5:1 strength factor-alloy steel Proof tested to 200% of rated load capacity Available in 17-4PH Stainless Steel (up to 5,000lbs/2,150kgs.) See page 486. Made in U.S.A. 3D Solid Models available in multiple formats from www.jergensinc.comU.S. Patent No. 6,652,012To add Lift ID to Hoist RingAdd “F” to the end of the partnumber Example: 23414F MJHJHLIF TING SOLUTIONSMØIILLKKGGCCBA Thread SizeDFDF"A" Thread SizeEERing BailInchBLarge BailLoadThreadHexPartCapacitySizeSize Torque /8-115/8-113/4-103/4-101-81-81 1/4-71 1/4-71 1/2-61 1/2-62-4 1/22-4 61 1/41 1/81 1/21 1/221 7/82 1/22 1/43341/211/211/211/211212121212121 7/8 3 25/321 7/8 3 25/321 7/8 3 25/321 7/8 3 25/322 1/2 4 7/82 1/2 4 7/82 1/2 4 7/82 1/2 4 7/811111 1/21 1/21 1/21 1/21 1/21 1/233334 1/24 1/24 1/24 1/211/3211/3211/3211/329/169/169/169/169/169/161 1/161 1/161 1/161 1/161 7/161 7/161 7/161 7/161/41/41/41/43/43/43/43/43/43/41 1/41 1/41 1/41 1/41 3/41 3/41 3/41 3/411111/2 2 1/41/2 2 1/41/2 2 1/41/2 2 1/434 7/1634 7/1634 7/1634 7/1634 7/1634 7/163 19/32 5 13/163 19/32 5 13/163 19/32 5 13/163 19/32 5 13/164 1/2 7 23/324 1/2 7 23/324 1/2 7 23/324 1/2 7 23/322 15/32 3 19/322 15/32 3 19/322 15/32 3 19/322 15/32 3 19/3246 3/846 3/846 3/846 3/846 3/846 3/88 5/32 9 21/328 5/32 9 21/328 5/32 9 21/328 5/32 9 21/3211 7/16 13 27/3211 7/16 13 27/3211 7/16 13 27/3211 7/16 13 27/323/43/43/43/41 1/41 1/41 1/41 1/41 1/41 1/42 1/22 1/22 1/22 1/23 1/43 1/43 1/43 743.844.7Phone: 800-537-4367 or 1 216-486-5540 Fax: 1 216-481-6193 E-mail: info@jergensinc.com www.jergensinc.com487
LIFTING SOLUTIONSLIFTING SOLUTIONS GROUPRing BailLarge BailLIF TING SOLUTIONSLarge BailPart Numbers:23926 thru 23936 (Inch)23974 thru 23987 (Metric)Ring BailPart Numbers:23906 thru 23918 (Inch)23956 thru 23968 (Metric) Replace Stationary Eyebolt Lifting Tooling Columns & Large Fixtures OEM Applications Lifting Die & MoldsTo add Lift ID to Hoist RingAdd “F” to the end of the partnumber Example: 23414F MetricLoadThreadHexPartCapacitySizeSize Torque WeightNumber(kg)ABCDEFGHIJKLM(N 9239822398323984239852398623987488400M8 X 1.25 1.2450M10 X 1.5 1.21050 M12 X 1.75 1.61900 M16 X 2.0 1.62150 M20 X 2.5 1.64200 M24 X 3.0 1.64200 M24 X 3.0 1.67000 M30 X 3.5 1.67000 M30 X 3.5 1.611000 M36 X 4.0 2.811000 M36 X 4.0 2.812500 M42 X 4.5 2.812500 M42 X 4.5 2.813500 M48 X 5.0 2.813500 M48 X 5.0 ens, Inc. 15700 S. Waterloo Road Cleveland, Ohio 44110-3898 271.641.641.77.17.27.37.419.119.319.419.619.720.0
LIFTING SOLUTIONSLIFTING SOLUTIONS GROUPSide-Pull Traditional StylePrecision Cast Body Rated at 5:1 Strength Factor Material: Alloy Steel Clevis, Ring, Bushing and Cap Screware magnetic particle inspected Clevis is x-rayed Finish: Black Oxide Bushing: Zinc Plated with conversion coating,yellow (inch), clear blue (metric) Proof Tested to 200% of Rated Load Capacity 3D Solid Models available in multiple formats from www.jergensinc.com Available with Envirolox protective finish. See page 494 for more information.360 swivel plus pivot point moves around boltto provide greater clearances in side lifting andwhen lifting rotating objects.To add Lift ID to Hoist RingAdd “F” to the end of the partnumber Example: 23414FLIF TING SOLUTIONS InchPartNumberEnvirolox pacityTorque(lbs)ABCDEFG(ft. 000290005/16-1823/8-1621/2-1335/8-1133/4-1041-841 1/4-761 1/4-861 1/2-661 1/2-862-4 1/2 5 1/4 x 10 1/22-8 5 1/4 x 10 1/22 1/82 3/83 3/83 5/855 3/86 7/86 7/87 7/87 7/81010223 3/163 3/16556 13/166 13/166 13/166 13/166 13/166 13/161 1/21 1/22 3/82 3/83 3/43 3/44 5/84 5/84 5/84 5/84 5/84 5/85/83/411 1/41 1/22222 1/22 1/23 1/83 1/83/83/85/85/8111 3/81 3/81 3/81 3/81 1/21 5031.5042.0042.00Stated load capacity based on specific thread torques as shown in chart.It is recommended that these torques be used when installing hoist rings.Phone: 800-537-4367 or 1 216-486-5540 Fax: 1 216-481-6193 E-mail: info@jergensinc.com www.jergensinc.com489
LIFTING SOLUTIONSLIFTING SOLUTIONS GROUPSide-Pull Traditional StylePrecision Cast BodyMetricPartNumberLIF TING nvirolox -E47357-E47358-ELoadCapacityTorque(kg)ABCDEFG(kg M)1Wt.(kg)2 325 M 8 x 1.25500 M 10 x 1.50725 M 12 x 1.751400 M 16 x 2.02290 M 20 x 2.53050 M 24 x 3.04850 M 30 x 3.57500 M 36 x .212.614All dimensions are in millimeters.Stated load capacity based on specific thread torques as shown in charts.It is recommended that these torques be used when installing hoist rings.12Bolt Replacement KitsInch ThreadMetric ThreadEnvirolox Hoist RingBolt KitBolt KitThreadWt.Part No.Part No.Part No.Size(lbs)Envirolox Hoist RingBolt KitBolt KitThreadWt.Part No.Part No.Part 49-E47349-085/16-183/8-161/2-135/8-113/4-101-81 1/4-71 1/4-81 1/2-61 1/2-82-4 47394-E47395-E47396-E47397-E47398-EM8M 10M 12M 16M 20M 24M 30M 36.02.03.07.14.32.531.032.0To add Lift ID to Hoist RingAdd “F” to the end of the partnumber Example: 23414F Bolt Kits contain bolt and retaining ring.Bolt Kits with -E are for use with Envirolox Hoist Rings. See page 494 for Hoist Ring hold down clips.490Jergens, Inc. 15700 S. Waterloo Road Cleveland, Ohio 44110-3898 USA
LIFTING SOLUTIONSLIFTING SOLUTIONS GROUPSP 2000 Side-Pull Style Extended D RingThe Jergens SP2000 Side-Pull Style Hoist Ring is ideal for flipping fixtures, dies and molds. Itswivels 360 and pivots around the center bolt providing the ring with greater clearances in sidelifting applications and when lifting rotating objects. The hoist ring is low profile and has a uniquebolt retention design. The oversized forged ring, and single piece forging, easily adapts to largerhoist hooks. Its relatively light weight makes it easier to handle than similar hoist rings and theinstallation is conveniently done with external wrenching (47531, 47532) or internal/externalwrenching (all other sizes). All parts are made in the U.S.A. Can Be Used for Top Lifting as well as side lifting applications Full Swivel & Pivot Action Rated at 5:1 strength factor at any angle Material: Heat Treated Alloy Steel Finish: Black Oxide Proof Tested to 200% of Rated Load Capacity Available in Metric sizes. See page 492. 3D Solid Models available in multiple formats from www.jergensinc.comTo add Lift ID to Hoist RingAdd “F” to the end of the partnumber Example: 23414FPatent Nos. 6,068,310and 409,895*For Part Numbers: 47537, 47538, 47539External Wrench MountingPart Numbers: 47531 & 47532LIF TING SOLUTIONS Internal/External Wrench MountingPart Numbers: 47533 thru 47539Inch Threads (Includes Gold 7100140001720029000ThreadSizeTorque Hex Wt.ABCDEFGHIJKLMNO (ft. lbs) Size (lbs)5/16-183/8-161/2-135/8-113/4-101-81 1/4-71 1/2-62-4 1/21 9/321 9/321 7/81 7/82 5/162 5/164 9/164 9/164 9/1615/32 13/165/8 13/163/4 1 3/815/16 1 3/81 1/8 1 7/81 1/2 1 7/81 7/8 3 1/42 1/4 3 1/43 3 1/41/81/85/325/321/41/423/6423/6423/649/16 5/169/16 5/1613/16 1/213/16 1/21 1/32 5/81 1/32 5/81 21/32 1 1/161 21/32 1 1/161 21/32 1 1/1611 2 1/16 1 3/411 2 1/16 1 3/41 3/4 1 1/2 3 3/821 3/4 1 1/2 3 3/822 1/4 242 5/82 1/4 242 5/83 3/4 3 7 11/16 4 3/83 3/4 3 7 11/16 4 3/83 3/4 3 7 11/16 4 3/8334 3/44 3/45 11/165 11/1610 7/1610 7/1610 7/163/4 1/2 1/23/4 1/2 1/21 1/4 3/4 7/81 1/4 3/4 7/81 3/4 1 1 1/81 3/4 1 1 1/83 1 5/16 1 7/83 1 5/16 1 7/83 1 5/16 1 7/84— .55— .515 1/4 225 5/16 250 3/8 4130 1/2 4.5150 3/4 24.50250 3/4 30300 3/4 26.50Phone: 800-537-4367 or 1 216-486-5540 Fax: 1 216-481-6193 E-mail: info@jergensinc.com www.jergensinc.com491
LIFTING SOLUTIONSLIFTING SOLUTIONS GROUPSP 2000 Side-Pull Metric - Extended D RingSIDE PULL APPLICATIONTOP PULL APPLICATIONLIF TING SOLUTIONS*For Part Numbers: 47587, 47588, 47591, 47589Patent Nos. 6,06
Shackle Radius D Shackle Diameter Size E Width Inside Shackle Clearance G Pin Hole to Base H Torque2 (kg*m) Weight Hex size With Shackle No Shackle With Shackle B1 No Shackle B2 With Shackle F1 No Shackle F2 With Shackle No Shackle 24450 24450NS M6 X 1.0 20
Jergens, Inc. Jergens Way 15700 S. Waterloo Road Cleveland, Ohio 44110-3898 USA THREADED INSERTS www.jergensinc.com 10.4 Keylocking Inserts Heavy Duty Industrial Style Metric Inserts - Heavy Duty Material: Carbon Steel Inserts - C1215 or equivalent Stainless Steel Insert - 303 Keys - 302 Finish: Carbon Steel Inserts - Parkerized
Lifting calculation method 3. DYNAMIC FACTOR When the movement of the precast unit is performed by lifting gear, dynamic forces that depend on the lifting gear used, appear. The lifting classes are described in DIN 15018. Lifting factor f is the acceleration factor. When lifting and carrying precast elements, the lifting load has to be
tm‐lvb1350 1350mm lifting beam ‐1.5t 8.9kg tm‐lvb1400 1400mm lifting beam ‐1.5t 8.9kg tm‐lvb1500 1500mm lifting beam‐ 1.5t 8.9kg tm‐lvb1600 1600mm lifting beam‐ 1.5t 10.3kg tm‐lvb1800 1800mm lifting beam‐ 1.5t 11.2kg tm‐lvb2000 2000mm lifting beam‐ 1.5t 14.7kg tm‐lvb2200 2200mm lifting beam‐ 1.5t 16.4kg
Lifting Systems 44 1-800-336-2598 DR-Anchor CONCRETE LIFTING SOLUTIONS Lifting System Economical and effective method for backstripping or face lifting in tension. The system code is stamped on the head of each anchor to match with the correct lifting unit. www.conaceb.com 45
A lifting beam is loaded in bending. Typically a simple lifting beam will have a single lifting eye above the beam which engages with the lifting machine hook and lower lifting eyes at points on the underside of the beam to connect to the load. A spreader, often called a spreader beam, is actually a strut loaded in compression.
1. Using the attachment points on the top of the Lifting Beam attach the relevant lifting chain. 2. Lift the lifting beam using the crane or suitable lifting apparatus. Move it to where the materials or goods are located. 3. Attach the materials or goods to the lifting beam using relevant lifting chains and safety accessories. 4.
LEEA 059-1 is one of a series of guides related to documentation and marking of a range of generic forms of lifting equipment as listed below: Part 1 - Manual Lifting Machines Part 2 - Powered Lifting Machines Part 3 - Lifting Machine Supporting Structures Part 4 - Lifting Accessories, Non-fixed load lifting attachments.
ASG, Division of Jergens, Inc. is an ISO 9001:2015 certified manufacturer, provider and service center for products and solutions focused around assembly. Since the 1970s, we have developed a first-class reputation unrivaled in the industry offering a wide range of world class products through our various world wide locations.
