Instruction Booklet Livret D’instructions

Operating your breville gourmet single cup brewer 8. Set the date dial on the Upper FilterHolder 2 months ahead. This willremind you when the Charcoal Filterwill need to be replaced.9. Place the assembled Filter Holder intothe Water Tank, aligning so the datedial is visible from outside the Tank.Push down hard on the assembledFilter Holder until it snaps into place.10. Your Brewer is ready for the one-timepriming process.NOTE:Replace the Water Filter every2 months, or 60 tank refills, moreif you have hard water.To order replacement WaterFilters, visit www.breville.com.We recommend removing the WaterFilter if you choose not to replacethe Water Filter every 2 months, asthe filter may clog and affect thesmell and taste of the water.One-time priming processPriming fills the internal tank with water andcleanses the brewing system. You cannotuse your Brewer until it has been primed forits first use.NOTE:If the Brewer has been exposed totemperatures below freezing, allowthe Brewer at least two hours toreach room temperature beforepriming. A frozen or extremely coldBrewer will not prime properly andcan cause damage.101. Unwrap the power cord and plug theBrewer into a grounded outlet.2. Place a 12 oz. mug on the Drip TrayPlate. The drip tray plate and drip traycan be removed to accomodate tallermugs and travel mugs.3. Fill the Water Tank with water up to the'MAX' mark on the viewing window.The Water Tank can be filled in two ways:a) Remove the Water Tank Lid and pourwater directly into the Water Tankwhile it is still attached to the Brewer,then replace the Lid.b) Remove the Water Tank Lid, thengripping the handle located on the leftside of the Water Tank, lift upwards.Fill with water. Place the Water Tankback onto the Brewer and replacethe Lid.NOTE:Do not use water that has beentreated by a 'water softener'. Theincrease in sodium levels in thewater can cause scaling in thebrewer and hinder its performance.4. Press and release the Power Switchlocated on the lower back, right side ofthe Brewer. The Power Switch is springloaded and will return to its originalposition.Operating your breville gourmet single cup brewer NOTE:If the Water Tank is empty or not inplace on the Brewer, the Water TankLED’s will flash and the LCD screenwill indicate ‘REFILL TANK’. Noneof the control panel buttons will beactive until water is added to theWater Tank.6. Once the water is heated, the LCDscreen will indicate 'OPEN HEAD'. Openthe Brewing Chamber Head by raisingand lowering the Safety Locking Armcompletely. Do not insert a K-Cup during this process. This will allow you torun a cleansing brew. The 'BREW' buttonwill now be illuminated.7. Press the 'BREW' button. This will starta cleansing brew which will completethe priming sequence. Hot water willflow into your mug. When the water flowstops, discard the hot water.NOTE:The Brewer will take about 4 minutesto heat up during the primingprocess.9. Fill the Water Tank with water up to the'MAX' mark on the viewing window.10. The LCD screen will indicate ‘OPENHEAD’. Open the Brewing ChamberHead by raising and lowering the SafetyLocking Arm completely. The LCDscreen will indicate ‘READY TO BREW’.11. The one-time priming process is nowcomplete and you are ready for yourfirst K-Cup brew (page 12) or MyK-Cup brew (page 14).8. The LCD screen will indicate ‘HEATING’as the Brewer heats the water for thenext brew cycle. Once the water isheated, the LCD screen may indicate‘REFILL TANK’.NOTE:For BKC600XL priming information,please refer to page 30.5. The Water Tank LED and LCD screen willilluminate. The Brewer will automaticallyfill with water and make a quiet vibratingsound. This is normal. The LCD screenwill indicate 'HEATING'.11

Operating your breville gourmet single cup brewer Brewing a K-Cup 1. Follow the instructions, Installing theWater Filter (page 9) and the One-timePriming Process (page 10). The Brewershould be turned on and the WaterTank should be filled and illuminated.2. The LCD screen will indicate ‘READYTO BREW’. Theandbuttonswill illuminate and the ‘BREW’ buttonwill illuminate and flash for up to60 seconds.NOTE:There are two sharp needles thatpuncture the K-Cup . One on theunderside of the Brewing ChamberHead and the other in the base ofthe K-Cup Holder. To avoid risk ofinjury, do not put your fingers in theBrewing Chamber or K-Cup Holder.NOTE:If the ‘BREW’ button is not pressedin 60 seconds, the LCD screenwill indicate ‘OPEN HEAD’ and the‘BREW’ button will be disabled toprevent accidental activation. Tore-activate the brew sequence,open the Brewing Chamber Headby raising and lowering the SafetyLocking Arm completely.3. Place a cup or mug on the Drip TrayPlate. The drip tray plate and drip traycan be removed to accomodate tallermugs and travel mugs.4. Raise the Safety Locking Arm. TheBrewing Chamber will open toward you.Operating your breville gourmet single cup brewer a) The LCD screen will indicate thedefault brew size (7.25 oz.). To choosea different size, press thebutton togo up in size or thebutton to godown in size.NOTE:Select from a stronger small cup(5.25 oz. serving), a small mug (7.25oz. serving), a large mug (9.25 oz.serving), a travel mug (11.25 oz.serving) or iced beverage setting(3.25oz serving). The iced beveragesetting is only available on the theBKC700XL.The small mug (7.25 oz. serving) isthe default brew size.To program your favorite brew size,refer to Setting the ‘BREW SIZE’feature (page 24).7. Lower the Safety Locking Arm toclose the Brewing Chamber Headover the K-Cup Holder. When closedcompletely, the LCD screen will indicate‘READY TO BREW’. Theandbuttons will illuminate and the ‘BREW’button will illuminate and flash for up to60 seconds.NOTE:To use the iced beverage setting,place a tall glass filled with ice on thedrip tray. Use your favorite K-Cup ,select the iced beverage brew sizebutton. Add more ice once brewingis complete, add cream and sugar ifdesired. The iced beverage setting isonly available on the BKC700XL.5. Select a K-Cup .6. Place the K-Cup in the K-Cup Holder (located in the BrewingChamber). Do not remove the foil lidor puncture the K-Cup .12b) Once the brew size is selected, pressthe ‘BREW’ Button. The ‘BREW’button will stop flashing, theandbuttons will no longer be lit. The LCDscreen will indicate ‘BREWING’ andthe selected brew size.NOTE:If the ‘BREW’ button is not pressedin 60 seconds, the LCD screenwill indicate ‘OPEN HEAD’ and the‘BREW’ button will be disabled toprevent accidental activation. Tore-activate the brew sequence,open the Brewing Chamber Headby raising and lowering the SafetyLocking Arm completely.8. The LCD screen will indicate‘BREWING’, however there may be ashort pause before the brewing processbegins. The process lasts about 60seconds and ends with a burst of air toremove all liquid from the K-Cup .13

Operating your breville gourmet single cup brewer NOTE:There is extremely hot water in theK-Cup Holder during the brewingprocess. To avoid risk of injury, donot raise the Safety Locking Arm oropen the Brewing Chamber duringthe brewing process.Following the brew, the LCD screenwill indicate ‘HEATING’ as theBrewer heats the water for the nextbrew cycle. This process lasts about15 seconds. The pump will make avibrating sound. This is normal.9. Raise the Safety Locking Arm, removeand dispose of the used K-Cup . Usecaution as the K-Cup will be hot.10. Enjoy your first cup of gourmet coffee,tea or hot cocoa!11. The LCD screen will indicate ‘READYTO BREW’, indicating that the nextK-Cup can be inserted for the nextbrew cycle.Brewing with the My K-Cup AccessoryThe Breville Gourmet Single Cup Brewer comes with a My K-Cup accessory. Thedishwasher safe, reusable My K-Cup allows you to use your own grind of coffeeso you can adjust the amount and type ofcoffee to suit your tastes. Along with theincluded measuring scoop, this accessoryconveniently stores in the easy opencompartment on top of the brewer.1. Follow the instructions, Installing theWater Filter (page 9) and the One-timePriming Process (page 10). The Brewershould be turned on and the Water Tankshould be filled and illuminated.Operating your breville gourmet single cup brewer 4. Open the storage compartment locatedon top of the Brewer by pressing thefinger indent on the right side. Removethe My K-Cup accessory.5. Disassemble the My K-Cup accessoryby removing the Lid from the Holder in acounterclockwise direction. Remove theFilter Basket from the Holder.6. Wash the My K-Cup Lid, Filter Basketand Holder in warm soapy water prior tofirst use. Rinse and dry thoroughly.7. Insert the Filter Basket into the Holder.14Or, if you like a stronger brew, selectthe small cup 5.25 oz. serving.If you grind your own beans:1. Start with a coarser grind similarto a French Press grind.2. Experiment with grinds similar todrip brewing grinds.3. Avoid a fine espresso grindsetting that could clog theFilter Basket or result in poorextraction.10. Place the assembled My K-Cup Holder into the Brewing Chamber.To do this:2. The LCD screen will indicate ‘READYTO BREW’.3. Place a cup or mug on the Drip TrayPlate. The drip tray plate and drip traycan be removed to accomodate tallermugs and travel mugs.We recommend this for the smallmug 7.25 oz. serving.9. Raise the Safety Locking Arm. TheBrewing chamber will open toward you.NOTE:Do not use water that has beentreated by a 'water softener'. Theincrease in sodium levels in thewater can cause scaling in thebrewer and hinder its performance.NOTE:If the ‘BREW’ button is not pressedin 60 seconds, the LCD screenwill indicate ‘OPEN HEAD’ and the‘BREW’ button will be disabled toprevent accidental activation. Tore-activate the brew sequence,open the Brewing Chamber Headby raising and lowering the SafetyLocking Arm completely.NOTE:1 level scoop 2 tablespoons8. Use the My K-Cup Measuring Scoopto fill the Filter Basket with 1 level scoopmaximum of coffee. 1 level scoop isequivalent to 2 tablespoons. Alternatively,there are line markings on the insideof the Filter Basket that indicate 1tablespoon and 2 tablespoons so youcan adjust the amount of coffee to yourpersonal preference. Do not fill the FilterBasket with more than one level scoopof coffee or tamp the grinds. Ensure thecoffee remains loose and there are nocoffee grinds remaining on the upperrim of the Filter Basket. Screw on theLid to seal.a) Remove the K-Cup Holder from theBrewing Chamber (10a). Store theK-Cup Holder in the My K-Cup Storage compartment located ontop of the Brewer.b) Insert the assembled My K-Cup Holder into the Brewing Chamber(10b), ensuring to align thearrowon the My K-Cup Lid with thearrow in the Brewing Chamber.15

Operating your breville gourmet single cup brewer Operating your breville gourmet single cup brewer a) The LCD screen will indicate thedefault brew size (7.25 oz.). Tochoose a different size, press theto go up in size or thebutton togo down in size.NOTE:There are two sharp needles usedto puncture the K-Cup and MyK-Cup Holder. One in the base ofthe K-Cup Holder, the other on theunderside of the Brewing ChamberHead. To avoid risk of injury, usecaution when inserting or removingthe K-Cup , K-Cup Holder or MyK-Cup Holder.11. Lower the Safety Locking Arm to closethe Brewing Chamber Head over theMy K-Cup Holder. When closedcompletely, the LCD screen will indicate‘READY TO BREW’. Theandbuttons will illuminate and the ‘BREW’button will illuminate and flash for up to60 seconds.NOTE:There is extremely hot water inthe My K-Cup Holder during thebrewing process. To avoid riskof injury, do not raise the SafetyLocking Arm or open the BrewingChamber during the brewingprocess.NOTE:Select from a stronger small cup(5.25 oz. serving), a small mug (7.25oz. serving), a large mug (9.25 oz.serving), a travel mug (11.25 oz.serving) or iced beverage setting(3.25oz serving). The iced beveragesetting is only available on the theBKC700XL.The small mug (7.25 oz. serving) isthe default brew size.To program your favorite brew size,refer to Setting the ‘BREW SIZE’feature (page 24).NOTE:To use the iced beverage setting,place a tall glass filled with ice onthe drip tray. Use your favoriteK-Cup , select the iced beveragebrew size button. Add more ice oncebrewing is complete, add cream andsugar if desired. The iced beveragesetting is only available on theBKC700XL.Following the brew, the LCD screenwill indicate ‘HEATING’ as theBrewer heats the water for the nextbrew cycle. This process lasts about15 seconds. The pump will make avibrating sound. This is normal.NOTE:If the ‘BREW’ button is not pressedin 60 seconds, the LCD screenwill indicate ‘OPEN HEAD’ and the‘BREW’ button will be disabled toprevent accidental activation. Tore-activate the brew sequence,open the Brewing Chamber Headby raising and lowering the SafetyLocking Arm completely.12. The LCD screen will indicate‘BREWING’, however there may be ashort pause before the brewing processbegins. The process lasts about 60seconds and ends with a burst of air toremove all liquid from the My K-Cup Holder.13. Raise the Safety Locking Arm, removethe assembled My K-Cup Holder. Usecaution as the My K-Cup Holder willbe hot.14. Disassemble the My K-Cup Holder byremoving the Lid from the Holder in acounter-clockwise direction. Removethe Filter Basket from the Holder,discard the grounds and rinse out theFilter Basket and Holder.15. 15. Enjoy your first cup of gourmetcoffee, tea or hot cocoa!b) Once the brew size is selected,press the ‘BREW’ Button. The‘BREW’ button will stop flashing,theandbuttons will no longerbe lit. The LCD screen will indicate‘BREWING’ and the selectedbrew size.1617

Operating your breville gourmet single cup brewer NOTE:The My K-Cup accessory isdesigned for ground coffee only.Do not:a) Use a K-Cup or coffee pod inthe My K-Cup Filter Basket.b) Use the My K-Cup FilterBasket with the K-Cup HolderAfter brewing with the MyK-Cup accessory, the K-Cup Holder must be inserted into theBrewing Chamber in order tobrew a K-Cup .To replace the K-Cup Holder, raisethe Safety Locking Arm, and removethe My K-Cup Holder. InsertK-Cup Holder into the BrewingChamber, aligning thearrow onarrowthe K-Cup Holder with thein the Brewing Chamber. Usecaution when doing this as thereis a sharp needle on the undersideof the Brewing Chamber Head thatpunctures the K-Cup .SROPPING THE BREW PROCESSTo stop brewing after the process hasstarted, press and release the PowerSwitch on the right side of the Brewer tothe ‘OFF’ status. The flow of coffee, tea orhot cocoa will stop, the heating elementwill shut off and the LED’s illuminating theWater Tank will no longer be lit. The LCDscreen will indicate the time, ‘ON-OFFTIME’ and ‘AUTO OFF’. None of the controlpanel buttons will be active until the Breweris turned back on.18NOTE:You may get less coffee, tea or hotcocoa during your next brew. Aftera terminated brew, we recommendthat you follow the instructions forBrewing hot water (page 18). Yournext brew will then dispense thecorrect volume according to thebrew size you have selected.Brewing hot waterThe Brewer is able to dispense a cup of hotwater for making hot chocolate in a packet,for use in cooking, for making soups, etc.Follow the instructions Brewing a K-Cup (page 12), without inserting a K-Cup .NOTE:After brewing a hot cocoa K-Cup ,or stopping the brew processmid-cycle, we recommend running ahot water brew cycle.Refilling the water tankThe LCD screen will indicate ‘REFILLTANK’ when the water level in the WaterTank is low or if the Water Tank has beenremoved.1. Fill the Water Tank with water up to the'MAX' mark on the viewing window. TheWater Tank can be filled in two ways:a) Remove the Water Tank Lid and pourwater directly into the Water Tank whileit is still attached to the Brewer, thenreplace the Lid.b) Remove the Water Tank Lid, thengripping the handle located on the leftside of the Water Tank, lift upwards. Fillwith water. Place the Water Tank backonto the Brewer and replace the Lid.Operating your breville gourmet single cup brewer 2. The LCD screen will indicate either:a) ‘OPEN HEAD’. Raise and lower theSafety Locking Arm completely.b) ‘HEATING’ as the Brewer heats thewater for the next brew cycle. Thisprocess lasts about 15 seconds. Thepump will make a vibrating sound. Thisis normal.3. Once the Safety Locking Arm is openedand lowered, or the water is heated,the LCD screen will indicate ‘READYTO BREW’, indicating the brew cyclecan begin. Theandbuttons willilluminate and the ‘BREW’ button willilluminate and flash for up to 60 seconds.NOTE:If the ‘BREW’ button is not pressedin 60 seconds, the LCD screenwill indicate ‘OPEN HEAD’ and the‘BREW’ button will be disabled toprevent accidental activation. Tore-activate the brew sequence,open the Brewing Chamber Headby raising and lowering the SafetyLocking Arm completely.2. If there is no water in the Water Tank, refillwith water. Place the Water Tank backonto the Brewer and replace the Lid.3. Ensure the Brewer is turned on. Raiseand lower the Safety Locking Arm on theBrewer without inserting a K-Cup .4. The LCD screen will indicate ‘READYTO BREW’ and the ‘BREW’ button willilluminate and flash.5. The LCD screen will indicate the defaultbrew size (7.25 oz. serving unlessprogrammed otherwise). Select thelargest brew size (11.25 oz. serving) bypressing the button on the control panel.6. Place a 12 oz. mug on the Drip TrayPlate. The drip tray plate and drip traycan be removed to accomodate tallermugs and travel mugs.7. Press the ‘BREW’ button. Hot water willflow into your mug. When the flow stops,discard the hot water.8. Repeat this process 2 more times tocompletely renew the water frominner tank.Do not remove the Water Tankduring the brewing process.Purging the brewerIf the Brewer has not been used for morethan one week, you should renew thewater from the inner tank by purging thebrewer.1. If there is water in the Water Tank,remove the Water Tank Lid, then grippingthe handle located on the left side ofthe Water Tank, lift upwards. Discardthe water, rinse and refill with bottled orfiltered water. Place the Water Tank backonto the Brewer and replace the Lid.19

MENU & PROGRAMMINGyour new Breville Gourmet Single Cup Brewer Menu & programming optionsSetting the ‘CLOCK SET’feature5. Press theorbutton to reach theappropriate minute.Setting the clock is optional. When theclock is set, the time will appear on theLCD screen.6. Once the appropriate minute is reached,press the ‘OK’ button. The LCD screenwill return to the menu programmingoptions.NOTE:You must set the clock if using the‘ON-OFF TIME’ feature.1. Press the ‘MENU’ button. The menuprogramming options will appear on theLCD screen with a blinking indicator on‘CLOCK SET’.2. Press the ‘OK’ button. The hour willblink, indicating the hour is ready tobe set.3. Press theorbutton to reach theappropriate hour. If the hour has passed12, the indicator switches from AMto PM.7. To exit the menu programming options,press the ‘MENU’ button. Alternatively,press thebutton to reach ‘EXITMENU’ and press the ‘OK’ button. TheLCD screen will return to the main screenand indicate the time selected.NOTE:If power is interrupted to theBrewer, the clock will need tobe reset. Programmed brew sizeand brew temperature settingsare remembered and restoredautomatically. All other settings willbe restored automatically after theclock is reset.4. Once the appropriate hour is reached,press the ‘OK’ button. The minutes willblink, indicating that the minutes areready to be set.2021

Menu & programming optionsMenu & programming optionsSetting the ‘ON-OFF TIME’featurev) Once the appropriate minute isreached, press the ‘OK’ button. TheLCD screen will display ‘OFF TIME’,indicating that the time you wish theBrewer to automatically turn off isready to be set.This feature allows you to programthe specific time when the Brewer willautomatically turn on and/or off. Byprogramming your Brewer to automaticallyturn on, you will not have to wait for theBrewer to heat the water in the WaterTank. It will take the Brewer approximately3½ minutes to heat the water from roomtemperate.NOTE:You must set the clock if using the‘ON-OFF TIME’ feature.An alternative to setting the‘ON-OFF TIME’ feature is to leavethe Brewer on all the time.Werecommend this so your Brewer isalways ready to brew a fresh cup ofgourmet coffee, tea or hot cocoa.To turn the Brewer off at any time,press and release the Power Switchon the lower back, right side of theBrewer. The clock will remain on ifset, however you can not activatethe brew cycle. Press and releasethe Power Switch again to restorepower to the Brewer. You will haveto wait for the water to heat upbefore the Brewer is ready to brew.1. Press the ‘MENU’ button. The menuprogramming options will appear on theLCD screen with a blinking indicator on‘CLOCK SET’.2. Press theTIME’.button to reach ‘ON-OFF3. Press the ‘OK’ button.Setting the ‘OFF TIME’i) Follow the instructions (ii to iv) forSetting the ‘ON TIME’.ii) Once the appropriate time isreached, press the ‘OK’ button. TheLCD screen will return to the menuprogramming options4. Press theortwo options:button to see thea) ‘ON-OFF TIME’ will be ‘INACTIVE’,indicating that the Brewer will notturn on or off automatically. Press the‘OK’ button to select this option. TheLCD screen will return to the menuprogramming options.This feature automatically turns the Breweroff after 2 hours from the last brew.1. Press the ‘MENU’ button. Theprogramming options will appear on theLCD screen with a bli

2 CONGRATULATIONS On the purchase of your new Breville Gourmet Single Cup Brewer CONTENTS 4 Breville recommends safety first 6 Know your Breville Gourmet Single Cup Brewer 8 Operating your Breville Gourmet Single Cup Brewer 9 - Installing the water filter 10 - One-time priming proc