Volvo Vida Dice User Manual - Obd2be
www.obd2be.com volvo vida dice User ManualContents1INTRODUCTION . 31.1SUPPORT. 31.2COMPONENTS . 31.3RANGE . 51.3.1Product . 51.3.2Replacement parts. 52GETTING STARTED . 62.1PROCEDURE FLOWCHART . 62.2UNINSTALL BUILT-IN BLUETOOTH . 62.3BEFORE INSTALLATION – VIDA CERTIFICATION AGENT . 62.4INSTALLATION AND CONFIGURATION OF BLUETOOTH SOFTWARE AND DICE SOFTWARE. 72.5INSTALLATION OF USB DRIVER FOR DICE .112.6CHECK AND UPDATE OF INTERNAL SOFTWARE IN DICE UNIT .132.7ADDING THE FIRST DICE UNIT IN VIDA.162.8CHOOSE DEFAULT COMMUNICATION TOOL IN VIDA .232.9CONNECTING DICE TO A VEHICLE .242.10REMOVING A DICE UNIT.242.11DICE FULL TEST BY MEANS OF DICE TEST UNIT .253VEHICLE COMMUNICATION .293.1BLUETOOTH .293.2USB .294BLUETOOTH – NOTE.304.1PERFORMANCE .304.2SAFETY AND RELIABILITY .305DESCRIPTION OF BLUETOOTH ICONS .316DESCRIPTION OF STATUS LEDS .326.1FIRMWARE STATUS (RED/GREEN).326.2USB COM STATUS (YELLOW) .326.3BLUETOOTH COM STATUS (BLUE) .336.4VEHICLE INTERFACE STATUS (ORANGE).336.5ADDING AN ADDITIONAL DICE UNIT IN VIDA.337HISTORY LOG .348ALPHABETIC REGISTER .35 Volvo Car Customer Service 2007135EN012(35)
www.obd2be.com 1 IntroductionDiCE – Diagnostic Communication Equipment, is a tool that is used together with VIDA All-in-one tocommunicate with the vehicle. Communication makes diagnosing and troubleshooting the vehiclepossible, as well as the downloading of software.DiCE uses Bluetooth to transfer information wirelessly between the vehicle and VIDA All-in-one. Thisgives the mechanics more flexibility. An USB cable can be used as an alternative to Bluetooth.1.1SupportFor support, use TIE template, DiCE under VIDA/Communication Tools in Service Product Reportor contact your local VCC Helpdesk.1.2ComponentsDiCE has an integrated CARB cable, which is connected to the vehicle's diagnostic socket.When connecting to the vehicle, DiCE is powered as long as the battery is charged.DiCE has a folding hook that is designed for hanging the unit from one of the grab handles in thevehicle for example. When DiCE hangs visibly, Bluetooth reception is optimized and it is alsovisible to the mechanic.DiCE is equipped with four status LEDs (Light Emission Diode) that indicate the status of thesoftware, the USB and Bluetooth communication and the interface to the car.At one end of the unit, there is a DC input where a battery cable or adapter (12 V) can beconnected. The adapter is used when upgrading and troubleshooting the DiCE.In the other end of the unit there is a removable cover that could be removed by turning the screwon the cover, se picture below. Volvo Car Customer Service 2007135EN013(35)
www.obd2be.com The inputs for USB and memory card 1 are located here.USBSD cardIn order to communicate with DiCE wirelessly, the VIDA client must also be equipped withBluetooth. Supported adapter for DiCE is Ezurios USB-to-Bluetooth-adapter, which is connectedvia the computer's USB port.When upgrading DiCE, a USB cable must be used. DiCE supports USB 2.0.12 V DC1Memory card (Secure Digital) will be used with Volvo Can Recorder, which will be launched in2007. Volvo Car Customer Service 2007135EN014(35)
www.obd2be.com DiCE Test Unit Switch9-12 VPower LEDDiCE Test Unit is used when performing DiCE Full Test.1.3Range1.3.1ProductNamePurposeDiCE, with integrated OBD cable1.3.2DiCE Test UnitUsed for troubleshooting DiCE.USB cable, 5 meters (16 feet)Used for Vehicle communication, ifBluetooth is not used.USB cable, 1 meter (3 feet)Used when installing and updatingDiCE software.Battery cableUsed for troubleshooting and updatingsoftware for DiCE.Bluetooth adapterUsed for wireless Vehiclecommunication.USB extension cable 2 meters (7 feet)Used as an extension for Bluetoothadapter.USB extension cable 0.5 meter (2 feet)Used as an extension for Bluetoothadapter.Replacement partsNamePurposeDiCE, with integrated OBD cable Volvo Car Customer Service 2007135EN015(35)
www.obd2be.com 2 Getting started2.1Procedure FlowchartUninstall built-inBluetoothBefore installation – VIDACertification AgentInstallation andconfiguration of BluetoothSW and DiCE SWInstallation of USB driver forDiCECheck and update of internal SW inDiCE unitAdding the first DiCE unit inVIDAChoose defaultcommunication tool in VIDA2.2Uninstall built-in BluetoothIf you have built-in Bluetooth in your PC or Toughbook it has to be uninstalled first. For moreinformation, contact your Sales Company regarding Panasonic 28 or 29. Otherwise contact yourretailer.2.3Before installation – VIDA Certification AgentBefore installing DICE or Bluetooth the VIDA Certification Agent program should be run. Thisprogram checks that the computer meets the required specifications for VIDA All-in-one.To run VIDA Certification Agent you must be logged in as administrator.VIDA Certification Agent reports if the specifications are met, gives warnings for anythingbetween the minimum and recommended specification and an error message for anything thatdoes not meet the specifications.Faults must be remedied or computers changed before installation, because VIDA All-in-onecannot be installed on a computer which does not meet the specifications. Volvo Car Customer Service 2007135EN016(35)
www.obd2be.com The VIDA Certification Agent can be downloaded from TIE. The program can also be obtainedfrom the local sales company.VIDA Certification Agent is also run automatically as a part of the VIDA installation program. Byrunning the program before installation it is easier to determine whether the computer can beused for VIDA or not.2.4Installation and configuration of Bluetooth software and DiCE softwareVIDA All-in-one has to be correctly installed before starting installation of DiCE and software forBluetooth. Installation of software for DiCE and Bluetooth is carried out from a VIDA DVD.Follow the instructions carefully.NOTE! Do not insert the Bluetooth USB adapter until the installation program requests it.NOTE! Close all other programmes before starting.Step1DescriptionIllustrationInsert VIDA 2006C installation disc.Click on VIDACUSTOMIZED.2Select installation ofBluetooth and DiCEOnly tick the Bluetoothand DiCE check boxes.Click on NEXT.NOTE! Only EzuriosBluetooth adapter issupported during the pilotphase.Continued in next page Volvo Car Customer Service 2007135EN017(35)
www.obd2be.com Step3DescriptionIllustrationThe installation startsThis might take up to 5minutes.4Insert the Bluetooth USBadapter in a USB port inyour computer when amoving imiage tells so.NOTE! The Bluetoothadapter which is includedwithin the DiCE installationkit will be displayed by adifferent type of pictureduring installation, asshown in the pictures.5If the computer isconnected to a network,a dialog will appear.Choose “Yes, now andevery time I connect adevice”. Click on NEXT.Continued in next page Volvo Car Customer Service 2007135EN018(35)
www.obd2be.com Step6DescriptionIllustrationInstall the software in theadapter.In the next window, selectto install softwareautomatically. Click onNEXT.7Finish the installation.Click on FINISH to finishthe installation.Continued in next page Volvo Car Customer Service 2007135EN019(35)
www.obd2be.com Step8DescriptionIllustrationComplete the installationThe icon for Bluetooth,shown in the status bar,changes color from red onblue to white on blue asillustrated in the picture.The Bluetooth icon will beblue on white as long asthe Bluetooth interface isactive.NOTE! It is very importantthat the icon changescolor to white on bluebefore next step. The colorchange might take severalminutes. Some PCconfigurations e.g. FordGlobal Client need to bereboted before this icon isshown.9Restart the computer Volvo Car Customer Service 2007135EN0110(35)
www.obd2be.com 2.5Installation of USB driver for DiCEFor each new or additional DiCE unit that is going to be used in VIDA, the USB driver must beinstalled separately. This is done automatically in Windows when the DiCE unit is inserted into anUSB port. Carry out the instructions below.Step1DescriptionIllustrationPower up and connectDiCE to a PC via USB1. Power up the DiCEunit by connecting12 V DC to the ADinput on the DiCE unit,se picture to the right.Use a cable with partnumber 9513004connected to thevehicle battery.2. Remove the cover ofthe DiCE unit byturning the screw onthe cover.3. Connect the shortUSB cable to the DiCEunit. This cable isincluded in the DiCEPilot Kit.Continued in next page Volvo Car Customer Service 2007135EN0111(35)
www.obd2be.com StepDescriptionIllustration4. Connect the USBcable to a free USBport in the computer.NOTE! Pull out theBluetooth adaptercable temporarily ifthere is only one USBport in the computer.5. The window shown inthe picture opensautomatically inWindows.NOTE! This might takeseveral minutes.6. Choose “Install thesoftwareautomatically”.7. Click on NEXT.2Finish the DiCEinstallation of USB driver.Click on FINISH. Theinstallation of the USBdriver for this DiCE unit iscompleted. Volvo Car Customer Service 2007135EN0112(35)
www.obd2be.com 2.6Check and update of internal software in DiCE unitCheck if there is a new version of the Firmware available.Update software in DiCE.Update of the internal software (also called Firmware) in a DiCE unit is done via VIDA All-in-one.This assumes that step 2.5 installation of USB driver for DiCE has been performed for the DiCEunit.The DiCE unit shall be connected with a USB cable and 12 V feed. Ensure that the Firmwarestatus LED is flashing green.USB is a safer data transmission than Bluetooth. Safe transmission is important when updatingsoftware. The user interface for updating software is available in English only.Step1DescriptionIllustrationConnecting DiCE1.Connect 12 V voltagefeed via the 12 V DC,p/n 9513004.2. Connect the DiCE unitvia a USB cable to thecomputer, see section2.5.2Choose DiCE unit in VIDA1. Click on PERFORMCOMPUTERSETTINGS in VIDAand then on theCOMMUNICATIONTOOL tab.NOTE! Do NOT clickon the dots.2. Click on DiCEUPDATE. TheFirmware Updatewindow is opened.Continued in next page Volvo Car Customer Service 2007135EN0113(35)
www.obd2be.com Step3DescriptionIllustrationUpdating the DiCE unitsoftware1. Ensure that the correctDiCE unit andsoftware, "NewFirmware file", arechosen in the FirmwareUpdate window. Therequired Firmware filewill be communicatedseparately. The firsttime DiCE are installedon a computer, theFirmware file must befound.It is located atC:\ProgramFiles\DiCE\Tools\DiCEx x.mot2. Click on UPDATE.3. The update takesabout one minute. Thequestion to the rightmight be shown if theDiCE unit already hasthe latest version of thesoftware. In this casethe unit could beupdated anyway byanswering YES to thequestion.4. Close the FirmwareUpdate applicationtool by clicking onCLOSE.5. If this fails, pleasepower off and poweron the DiCE again andretry.6. When the update isfinished, the text“Device update OK” isviewed.Continued in next page Volvo Car Customer Service 2007135EN0114(35)
www.obd2be.com Step4DescriptionIllustrationClose the PERFORMCOMPUTER SETTINGSwindow by clicking on OK. Volvo Car Customer Service 2007135EN0115(35)
www.obd2be.com 2.7Adding the First DiCE Unit in VIDANOTE! Sections 2.4 and 2.5 will be repeated each time a new or additional DiCE unit will beadded.To add a DiCE, carry out the following:StepDescription1Start VIDA All-in-one.Choose the START tab.2Click on PERFORMCOMPUTER SETTINGSIllustrationand then theCOMMUNICATION TOOLtab.Continued in next page Volvo Car Customer Service 2007135EN0116(35)
www.obd2be.com Step3DescriptionIllustrationClick on the DiCE radiobutton.To add a DiCE, click onthe button with three dots( ) to the right of theDiCE drop-down list.4Click on ADD. If a DiCE isalready installed, thewindow looks different.NOTE! If one or moreDiCE:s are alreadyconfigured, this will beshown.5Follow the instructions andclick on CONTINUE. VIDAwill search for a new DiCE.This will take about 10seconds. The DiCE ID willbe shown in the dropdown menu.Continued n the drop-down list for communication tool.4. In the DiCE unit drop-down list, select a DiCE unit to be removed and click on REMOVE.423 Volvo Car Customer Service 2007135EN0124(35)
www.obd2be.com 2.11 DiCE Full Test by means of DiCE Test Unit1. Find the DiCE Test Unit2. Power up the DiCE by connecting 12 V DC, part number 9513004, to the DiCE TestUnit. NOTE! The power LED should now be lit.3. Connect the DiCE to the DiCE Test Unit. NOTE! The vehicle interface status LED is nowlit (firm red light).4. Start VIDA All-in-one. Select the START tab.5. Click on PERFORM COMPUTER SETTINGS and then the COMMUNICATION TOOLtab.6. Click on the dots beside the DiCE option in the drop-down list for theCOMMUNICATION TOOL.7. In the DiCE unit drop-down list, select the appropriate DiCE and click the Testcommunication tool. Volvo Car Customer Service 2007135EN0125(35)
www.obd2be.com 8. Click on RUN9. Set the DiCE Test Unit Switch to position 1. Click on OK.DiCE Test Unit SwitchCARB-cable contact Volvo Car Customer Service 2007135EN0126(35)
www.obd2be.com 10. Set the DiCE Unit Switch to position 2. Click on OK. Click on CLOSE. Volvo Car Customer Service 2007135EN0127(35)
www.obd2be.com 11. CONGRATULATIONS!You have successfully managed to perform a DiCE Full Test by means of DiCE Test Unit.12. If this will not work, the following will be shown:Please check thouroughly the switch positions and try again. If it still does not work, the DiCEUnit is out of order and has to be replaced.Repeat this section for both DiCE connected via USB and Bluetooth. Volvo Car Customer Service 2007135EN0128(35)
www.obd2be.com 3 Vehicle communication3.1BluetoothBluetooth is used to transfer information wirelessly between the vehicle and VIDA All-in-one.3.2USBA USB cable can be used as an alternative to Bluetooth. The USB cable is connected to theDiCE.The cover of the DiCE unit could be removed by turning the screw, as shown below.USB has priority to Bluetooth. Volvo Car Customer Service 2007135EN0129(35)
www.obd2be.com 4 Bluetooth – note4.1PerformanceTo optimize the performance for wireless transfer, it is important to remember that someelectronic appliances compete for the same frequency band. WLAN, DECT telephones, mobiletelephones and other Bluetooth units are a few examples of equipment that limit the performanceif they are used at the same time as DiCE in a workshop environment. The signals can beweakened by walls, furniture, panels, people etc.DiCE has a wireless range of 100 meters with clear visibility. To achieve stable communicationwith the vehicle, the distance should be limited to approximately 50 meters. Hang the DiCE up inthe vehicle using the hook and point the Bluetooth adapter towards the DiCE.Make sure that no obstacles are positioned between the DiCE and the Bluetooth.4.2Safety and reliabilityBluetooth technology guarantees interference protection and increases data security in manyways. The technology uses 128 bit encryption to prevent data being read by another party in theevent of the signal being hijacked. This is rare.To guarantee a high level of reliability, the signal can be transmitted over 70 different frequencies(on the 2.4 GHz frequency band). DiCE shifts between different intervals up to 1600 times persecond to find the most reliable frequency. Volvo Car Customer Service 2007135EN0130(35)
www.obd2be.com 5 Description of Bluetooth iconsIconDescriptionWhite on Blue - Bluetooth USB adapter operationalRed on Blue - Bluetooth USB adapter not operationalGreen on Blue – Established connection to Bluetooth USB Volvo Car Customer Service 2007135EN0131(35)
www.obd2be.com 6 Description of status LEDs6.1Firmware status (red/green)Firmware statusDescriptionFlashing greenDiCE is powered and operational.Flashing redCorrupt software or no software.Upgrading of internal software (Firmware) isnecessary.6.2Flashing red and green alternatelyDiCE is being programmed.Continuous redSerious fault in the DiCE unit.OffStandby.USB com status (yellow)USB com statusDescriptionContinuous yellowUSB connection connected.Flashing yellowUSB communication in progress.OffStandby.When connecting USB when DiCE is powered, the status LED for USB flashes quickly forapproximately three seconds. Volvo Car Customer Service 2007135EN0132(35)
www.obd2be.com The status LED for USB communication has nothing to do with the USB standard.6.3Bluetooth com status (blue)Bluetooth com statusDescriptionContinuous blueBluetooth connection connected.Flashing blueBluetooth communication in progress.OffStandby.When DiCE is powered, the status LED for Bluetooth communication flashes quickly forapproximately three seconds. If initiation fails, the status LED continues to flash. If no Bluetoothmodule is mounted on the DiCE unit or if the module is broken, the status LED never lights.The status LED for Bluetooth communication has nothing to do with the Bluetooth standard.6.4Vehicle interface status (orange)Vehicle interface statusDescriptionFlashing orangeCommunication on one more of the vehicle'sinterfaces in progress.Continuous orangeDiCE Test Unit connected.OffStandby.Flashing orange indicates communication in progress. It is not possible to differentiate between:6.5 Internal communication (DiCE transmits something or loop back test is performed). Vehicle activity (DiCE not involved). Communication between DiCE and ECU in the vehicle. The status does not flash if DiCEtransmits data without being connected to the vehicle or DiCE Test Unit.Adding an additional DiCE unit in VIDATo connect DiCE and communicate with the vehicle, the unit must be added to the VIDA client.Every DiCE that is to be used by a VIDA client must be configured separately.HINT! As a suggestion, install all DiCE units when configuring the VIDA application.Repeat the procedure in section 2.4 to and including section 2.5. Volvo Car Customer Service 2007135EN0133(35)
www.obd2be.com 7 History logThis is the first edition of the DiCE manual and has no history log.Changes and additions to the manual will be noted here. Volvo Car Customer Service 2007135EN0134(35)
www.obd2be.com 8 Alphabetic registeradd, 16remove, 24Art. no., 5software, 13Bluetooth, 3, 7, 29, 30status lamp, 3, 33connecting, 24update, 13diagnostic socket, 3USB, 3, 29Installation, 7VIDA, 33Installation disc, 7VIDA Certification Agent, 6 Volvo Car Customer Service 2007135EN0135(35)
volvo vida dice User Manual. . 2.4 Installation and configuration of Bluetooth software and DiCE software . VIDA All-in-one has to be correctly installed before starting installation of DiCE and software for Bluetooth. Installation of softwa
Volvo 3P-AE 15500 4 Volvo Group Trucks Buses Construction Equipment Volvo Penta Volvo Aero Financial Services Volvo 3P Volvo Powertrain Volvo Parts Volvo Logistics Volvo Information Technology Volvo Group Real Estate, Volvo Technology Volvo Business Services. Volvo 3P-AE 15500 5 AE-Curitiba
John Deere 425 445 455 Service Repair Manual in the technological know-how of archaeology. . mini volvo excavator volvo mini excavators wheel loaders volvo volvo wheel loader . volvo l90 specs gold rush excavator volvo ec750e specs volvo 290 volvo motor grader volvo
the Volvo tonality for pictures. See Volvo Brand Communication Guideline for click the Compress further information. Only use these approved Volvo colors. Use the colors in 100% only – never in tints. For more information and RGB color codes please select the Volvo Layout “Volvo Brand Colors”. Volvo Profile colors Volvo Accent colors
volvo construction equipment parts . Cat Caterpillar 416c Backhoe Loader Service Repair Manual champion motor graders shippensburg volvo volvo off road truck . champion grader volvo construction equipment dealer near me volvo 160 a25g volvo volvo ecr88 specs volvo heav
1995 Volvo 850 1995-96 Manual A/C-Heater Systems Volvo 850 * PLEASE READ THIS FIRST * . WIRING DIAGRAMS. Fig. 9: Manual A/C-Heater System Wiring Diagram. Title: Volvo 850 Manual AC Heater Systems (MCC) Author: Volvo Owners Club UK Created Date: 0-01-01T00:00:00Z .
VOLVO VIDA Installation Guide 3 . 1. Install VOLVO VIDA . To install VOLVO VIDA, Driver C: must be NTFS format, with at least 10G free space. IE 6.0 needed. Put the VIDA in
VOLVO V70 & XC70 Owners Manual Web Edition. DEAR VOLVO OWNER THANK YOU FOR CHOOSING VOLVO We hope you will enjoy many years of driving pleasure in your Volvo. The car has been designed for the safety and comfort of you and your passengers. Volvo is one of the safest cars in the world. Your Volvo
The Icecast Anatomy pressure casting system allows the clinician to produce a reliable, repeatable and well-fitting TSB socket. DESIGN Icecast Anatomy is a single chamber pressure casting system, which provides pressure to shape the soft tissue. The single chamber pressure system is designed to provide optimal pressure distribution. The chamber is reinforced with matrix, for durability and to .
