800-09618V1-A V128FBPT V250FBPT-pg
V IS T A - 1 2 8 F B P TV IS T A - 2 5 0 F B P TCommercial Fire and BurglaryPartitioned Security System with SchedulingProgramming Guide800-09618V1 11/12 Rev. A
Table of ContentsProgramming Field Settings for UL864 Compliance . 2Expert Mode Zone Programming . 38Report Code Programming . 40Alpha Descriptors Programming . 44Alpha Descriptor Vocabulary . 47Device Programming. 48Output Programming . 51Relay Voice Descriptors . 56System Layout Worksheets . 58Output Devices Worksheets . 74Scheduling . 80Scheduling Menu Mode . 83Programming Field Settings for ULC304 Compliance . 4Recommended Programming Procedure . 6Program Field Index . 7VISTA-128FBPT/VISTA-250FBPT Programming . 8Programming With #93 Menu Mode . 26Zone Programming. 27Zone Number Designations. 27Zone Response Type Definitions . 30Zone Input Type Definitions . 315800 Series Transmitters Loop Designations. 37Programming Field Settings for UL864 ComplianceNOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING JURISDICTION, AND OTHER INVOLVEDPARTIESThis product incorporates field-programmable software. In order for the product to comply with the requirementsin the Standard for Control Units and Accessories for Fire Alarm Systems, UL 864, certain programming featuresor options must be limited to specific values or not used at all as indicated below.Program feature or option Permitted in Possible settingsSettings permitted in UL 864UL864? Y/N 08 TEMPORAL SIREN PULSEN 13 BELL 1 TIMEOUTY 14 RS232 comm.N 17 AC LOSS KEYPADSOUNDING 19 RANDOMIZE AC LOSSREPORTN 20 TELEPHONE MODULEPHONE CODEN 22 KEYPAD PANIC ENABLES(PARTITION SPECIFIC) 23 MULTIPLE ALARMS(PARTITION SPECIFIC) 24 IGNORE EXPANSIONZONE TAMPER 26 INTELLIGENT TESTREPORTING 27 TEST REPORT INTERVALN 28 POWER-UP IN PREV.STATE 37 DOWNLOAD COMMANDENABLES 41 NORMALLY CLOSED OREOLR (ZONES 3-8) 42 DIAL TONE PAUSEYYNNNYNNY0 disable1 enableEnter 01-15 multiplied by 2 minutes.00 no timeout.0 no1 yes0 disable1 enable0 within 2 minutes1 10-40 minutes2 1-3 hours3 6-12 hours without Type 13, 1-3hours with Type 131-9 first digit of access code or # second digit of access code(enter # 11 for “ ”, or # 12 for “#”)To disable enter 00 for the 1st digit0 disable1 enable0 disable1 enable0 disable (tamper detection)1 enable (no tamper detection)0 disable1 enableEnter 0001-9999 for the test reportinterval in hours.Enter 0000 for test reporting.0 disable1 enable0 disable1 enable0 EOLR supervision1 N.C. loopsEnter the wait time for dial tonedetection:0 5 seconds; 1 11 seconds; 2 30seconds.–2–Not used at this time. Must be set to“0” (disable).Must be set to “3” (Minimum of 6minutes).Must be set to “0”.Must be set to “1” (enabled).Must be set to “2”.Not Used. Must be set to “00”.Must be set to “000” for partition 1in fire systems.Must be set to “1” (enabled).Must be set to “0” (enabled).Must be set to “0” (disable).Must be set to “0024” (Maximum 24hours)Must be set to “1” (enable).Must be set to “0” for all entries(disable).Must be set to “0” (EOLRSupervision).Must be set to “0” (5 seconds).
Program feature or optionPermitted inUL864? Y/N 44 RING DETECTION COUNTN 56 DYNAMIC SIGNAL DELAYY 77 AUTO TRBL RSTRY 80 ZONE TYPE 9 -10, 14RESTORE 84 SWINGER SUPPRESS.(PARTITION – SPECIFIC)1 12 PROGRAMNOTIFICATION1 13 SYS. SENSOR REV.RELAYN1 18 AFFECTS LOBBY(PARTITION – SPECIFIC)1 19 ARMS LOBBY(PARTITION – SPECIFIC)1 22 thru 1 25 CROSS-ZONINGPAIRS (1 – 4)1 28 RF TX LOW BATTERYSOUND1 29 RF TX LOW BATTERYREPORTING1 30 RF RCVR CHECK-ININTERVALNNYNNNNNN1 31 RF TX CHECK-ININTERVALN1 35 ACS DLR ENABLESN1 44 RF KEYPAD TAMPERDETECTION1 45 EXIT DELAY SOUNDING(PARTITION SPECIFIC)1 48 RF KEYPAD ASSIGN 18 PART. 0 NO1 49 SUPPRESS TX SUPERV.SOUND1 53 DOWNLOAD CALLBACKN1 57 ENABLE 5800 RFBUTTON GLOBAL ARM1 58 ENABLE 5800 RF FORCEARM1 60 ZONE 5/AUDIO ALARMVER.1 72 PRINTER ON-LINE MODENNNNNNNN1 76 ACCESS RELAY #(PARTITION SPECIFIC)1 78 EXT. HOME CONTROLEVTN1 79 HOME CONTROLEVENTSN1 80 LOG-FAULTS &RESTORESNNPossible settingsSettings permitted in UL 864Enter 00 to disable ring detection.Enter 01-14 for ring counts of 1-14.Enter 15 to select Answering MachineDefeat ModeEnter 00-15 times 15 seconds.Must be set to “00” (disable).0 disable1 enable0 disable1 enableEnter 01-14,Enter 00 for unlimited reports0 no1 yes0 use neither Zone 1 or Zone 2 inputs1 use Zone 1 input;2 use Zone 2 input;3 use Zone 1 and Zone 2 inputs.0 disable1 enable0 disable1 enableEnter 001-250Enter 000,000 to disable0 disarmed state only1 both armed and disarmed states0 disable1 enableEnter 02–15 times 2 hours (4–30hours)Enter 00 to disable receiversupervisionEnter 02–15 times 2 hours (4–30hours)Enter 00 to disable transmittersupervision0 disable1 enable0 disable1 enable0 disable1 enable0 none1-8 partition number0 disable1 enable0 callback required1 no callback required0 disable1 enable0 disable1 enable0 disable1 enable0 disable1 enable01-96 relay number00 relay not used.1 extended0 limited0 disable1 enable0 disable1 enable–3–Must be set to “6” (90 seconds).Must be set to “1” (enable).Must be set to “1” (enable) for zonetype 9.Must be set to “00” (disable).Must be set to “1” (yes).Not Used. Must be set to “0”.Must be set to “0” (disabled) forpartition 1.Must be set to “0” (disabled) forpartition 1.Must be set to “000,000” (disabled)for fire zones.Must be set to “1” (both armed anddisarmed states).Must be set to “1” (enable).Maximum is 02 (4 hours) for fireinstallations.Maximum is 02 (4 hours) for fireinstallations.Not used. Must be set to “0”.Not used. Must be set to “0”.Must be set to “0” (disable) forpartition 1.Not used. Must be set to “0”.Must be set to “0” (disable).Must be set to “0” (callbackrequired).Must be set to “0” (disable).Must be set to “0” (disable).Must be set to “0” (disable).Not used. Must be set to “0”.Must be set to “00” (relay not used)for partition 1.Not used. Must be set to “0”.Not used. Must be set to “0” in eachentry.Not used. Must be set to “0”.
Program feature or optionPermitted inUL864? Y/N2 07 AUTO-DISARM DELAY(PARTITION SPECIFIC)N2 18 ENABLE GOTO FORPARTITION (PARTITIONSPECIFIC)2*21 SUPERVISION PULSES FORCOMMUNICATIONS DEVICE2 22 DISPLAY OTHER FIREALARMS (PARTITION SPECIFIC)2 23 DISPLAY OTHER BURG &PANIC (INCLUDING CO ALARMS)(PARTITION SPECIFIC)2 24 DISPLAY TROUBLES OFOTHER PARTITIONS (PARTITIONSPECIFIC)3 01 EVENT DISPLAY LOCKN3 12 ZN TYPE 18 DELAY USEN3 13 “SUPV” ON OPEN ANDSHORT (APPLIES TO ZONE TYPE183 14 W.F. ALARM SILENCE OPT.NN3 16 ZONE TYP 17/18 DLYN3 18 EXTENDED DLY FOR TYP17/183 20 TRIG OUTS FUNC SEL(ONLY APPLIES TO VISTA128FBPT)3 21 MAX ATEMPTS3 50 ZONE TYPES 16-18 REST.N3 55 RESET ON 2ND OFF FORBELL 13 56 RESET ON 2ND OFF FORBELL 23 57 CONFIRM ARM BELL 2, AUXN3 59 CHIME ON BELL 2, AUXN3 60 BELL 2, AUX RLY TIMEOUTY3 82 BURG FEATURES ENABLEDNRESTRICTION FOR FIRE RELAYSYPossible settingsSettings permitted in UL 86400 no delay.01-14 times 4 minutes (04-56) delay.15 no auto disarming.0 disableMust be set to “15” (no autodisarming) for partition 1.1 enableMust be set to “0” (disable) forpartition 1.0 disable1 enable0 disable1 enable0 disable1 enableNot Used. Must be set to “00000”(disable).Must be set to “0” (disable) forpartition 1.Must be set to “0” (disable) forpartition 1.N0 disable1 enableMust be set to “0” (disable) forpartition 1.N0 disable1 enable0 disable1 enable0 Trouble on open/Supv on short1 Supv on open/Supv on shortMust be set to “1” (enable).0 Silenced by User Code OFF1 Silenced when zone restoresEnter 01-15 times 2 secondsEnter 00 for no delay0 no extended delay1 multiply delay by 40 remote keypad sounder1 keyswitch LEDsMust be set to “0” (Silenced by UserCode OFF).Must be set to 00 (no delay).1-80 disable1 enable0 disable1 enable0 disable1 enable0 disable1 enable0 disable1 enableEnter 01-15 multiplied by 2 minutes.00 no timeout.0 disable1 enableYesNoMust be set at 3, 4 or 5.Must be set to “1” (enable).NNNNYNNNMust be set to “0” (disable).Must be set to “0”.Must be set to 0 (no extended delay).Must be set to 0 (remote keypadsounder).Must be set to “0” (disable).Must be set to “0” (disable).Must be set to “0, 0” (disable).Must be set to “0” (disable) if Bell 2or Aux Relay is used for Fire.Must be set to “3” (Minimum of 6minutes).Must be set to “0” (disable).Restriction for # 70 must be set toYes when programming fire relays.Programming Field Settings for ULC304 ComplianceNOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING JURISDICTION, AND OTHER INVOLVEDPARTIESThis product incorporates field-programmable software. In order for the product to comply with the requirementsin the Standard for Signal Receiving Centre and Premise Burglar Alarm Control Units, ULC S304, certainprogramming features or options must be limited to specific values or not used at all as indicated below.Program feature or optionSettings permitted in ULC S304Possible settings 38 PREVENT ZONE XXX BYPASS(PARTITION SPECIFIC)Enter a zone number (001-250).Enter 000 if all zones can be bypassed.Must be set to “000” (all zones can bebypassed).1 58 ENABLE 5800 RF FORCE ARM0 disable, 1 enableMust be set to “0” (disable).2 03 ULC S304 ENABLE0 disable, 1 enableMust be set to “1” (enabled).2 08 FORCE-ARM ENABLE(PARTITION SPECIFIC)0 disable, 1 enableMust be set to “0” (disable).–4–
NOTE: All references in this manual for number of zones, number of user codes, number of access cards, and theevent log capacity, use the VISTA-250FBPT’s features. The following table lists the differences between the VISTA128FBPT and the VISTA-250FBPT control panels. All other features are identical.FeatureNumber of ZonesNumber of User CodesEvent Log CapacityVistakey ModulesNumber of Access 100015500The purpose of this document is to provide a quick and easy way to program your entire system. A recommendedprogramming procedure is included, followed by a list of program fields with the corresponding program group they belong to(system-wide, partition-specific, scheduling, etc.). Two program forms are included. One contains all the programming fields,and the other contains the partition-specific fields. If you are setting up a single-partition system, the partition-specific fieldsbecome system-wide fields.Following the program forms are system layout worksheets. We recommend that you use these sheets to plan your systembefore programming is performed. If you need further information about specific programming options, see the VISTA128FBPT/VISTA-250FBPT Installation and Setup Guide.Make sure that one two-line alpha keypad is connected to the control and is set to device address "00."Single-Partition SystemThe system default is for a single-partition system. Use the VISTA-128FBPT/VISTA-250FBPT SINGLE PARTITIONPROGRAMMING FORM when programming for single-partition usage. Follow the steps outlined in RECOMMENDEDPROGRAMMING PROCEDURE of this document for proper programming procedure.Multiple-Partition SystemYou must enter the number of partitions you are using in data field 2 00 to set the system for multiple partitions. Use theVISTA-128FBPT/VISTA-250FBPT SINGLE PARTITION and the PARTITION-SPECIFIC PROGRAM FORMS whenprogramming the system for multiple partitions. Follow the steps outlined in RECOMMENDED PROGRAMMINGPROCEDURE of this document for proper programming procedure. SUMMARY OF PROGRAMMING COMMANDSTo enter program mode, enter installer code [8] [0] [0] [0]To set standard defaults, press 97To change to next page of program fields, press 94To return to previous set of fields, press 99To erase account and phone number field entries, press [ ] field number [ ]To assign zone descriptors, press #93 follow menu promptsTo add custom words, press #93 follow menu promptsTo enter Installer's Message, press #93 follow menu promptsTo exit program mode, enter 99 OR 98: 99 allows re-access to programming mode by installer code. 98 prevents re-access to programming mode by installer code. The only way to re-access programming modeis by depressing both the [ ] and [#] keys at the same time within 30 seconds of power-up.Standard default ( 97) values are shown in brackets [ ], otherwise default 0.–5–
Recommended Programming ProcedureThe following is a step-by-step procedure recommended for programming your VISTA-128FBPT/VISTA-250FBPTsystem.1. Set the keypads (and other peripheral devices) to the appropriate addresses.2. Set factory defaults by pressing 97.This will automatically enable keypad addresses 00-01, so be sure at least one keypad is set to one of theseaddresses.3. Program system-wide (global) data fields.Using the programming form as a guide, enter program mode and program all system-wide programmingfields. These options affect the entire system, regardless of partitions. They include control options,downloader and dialer options, RF options, event logging options, etc. Refer to the Program Field Index for alisting of the program fields and their function.Note that field 2 00 (number of partitions) must be programmed before continuing.4. Program partition-specific fields.When the system-wide fields have been programmed, program all partition-specific programming fields byfirst pressing 91 to select a partition (while still in data field program mode). Then enter the first partitionspecific field number 09. When you are finished, the next partition-specific field is automatically displayed.Partition-specific fields can have different values for each partition. To program the fields for the next partition,press 91, enter the desired partition number, then enter field 09.5. Use #93 Menu Mode for device programming.Refer to Device Programming in this guide to assign keypad ID numbers and default partitions for eachkeypad, and to selectively suppress certain keypad sounding options. Also use this mode to assign RFreceivers, relay modules, and Communicators (7847i, GSMV/GSMHS, IGSMV/IGSMHS).6. Use #93 Menu Mode for zone programming.Refer to Zone Programming in this guide to program zone response types, assign right loop zones andwireless zones, assign zones to partitions, and to program alarm report codes.7. Use #93 Menu Mode for programming outputs.Refer to Output Programming in this guide to program desired output operation.8. Program Communication options.Refer to System Communication section in the VISTA-128FBPT/VISTA-250FBPT Installation and SetupGuide for detailed instructions. Then use #93 menu mode to program report codes.9. Use #93 Menu Mode for programming alpha descriptors.Refer to Alpha Programming in this guide to enter zone and partition descriptors and a custom installer'smessage.10. Use #80 Mode for programming schedules.Refer to the Scheduling Menu Prompts in this guide to program open/close schedules, temporary and holidayschedules, limitation of access schedules, and time-driven events.11. Define user access codes.Refer to User Access Codes in the VISTA-128FBPT/VISTA-250FBPT Installation and Setup Guide toprogram authority level, O/C reporting option, partition assignments, and wireless key assignments for eachuser.12. Exit Programming Mode.Exit programming mode by pressing either 98 or 99. Additional entries of 99 are required if the exit isbeing done from fields 1 00 and above.To prevent re-access to programming mode using the Installer's code, use 98. The only way to re-accessprogramming mode is by depressing both the [ ] and [#] keys at the same time within 30 seconds of powerup.Exiting by using 99 always allows reentry into programming mode using the Installer code. Either way ofexiting allows access via downloading. Note that if local programming lockout is set via downloading,programming mode cannot be entered at the keypad. Alternatively, if the “Installer Lockout Time” option is enabledin Compass, then the installer can only enter programming either within 24 hours of exiting programming, or when aMaster Code opens up a 24-hour window by entering their code #65.–6–
Program Field IndexOn the following pages, the programming fields have been arranged in numerical order. Use this index to cross-reference thefields on the programming form.FieldGroupField GroupField Group 00 04 05 06 08 09 10 11 12 13 14 15 16 17 19 20 22 23 24 25 26 27 28 29 31 32 33 34 35 36 37 38 39 40 41 42 44 45 47 51 56 57 58 59 77 icationsCommunicationsCommunicationsCommunications 80 83 84 85 88 89 901 111 121 131 151 171 181 191 201 211 221 231 241 251 261 281 291 301 311 341 351 421 431 441 451 471 481 491 501 511 521 531 541 551 561 571 581 601 701 71Communications1 72System-WideCommunications1 74System-WidePartition-Specific1 75System-WidePartition-Specific1 76Partition-SpecificPartition-Specific1 771 781 791 802 002 012 022 032 052 062 072 082 092 102 112 182 192 222 232 243 003 013 123 133 143 163 173 183 203 213 303 503 553 563 573 593 603 613 823 deSystem-Wide
VISTA-128FBPT/VISTA-250FBPT ProgrammingSome fields are programmed for each partition (shown as shaded fields). If you are programming a multiple-partition system,see the Partition-Specific Fields section for programming these fields. Standard default ( 97) values are shown in brackets [ ];otherwise, default 0.Data field programming involves making the appropriate entries for each of the data fields. Start Data Field programming byentering the installer code 8 0 0
NOTE: All references in this manual for number of zones, number of user codes, number of access cards, and the event log capacity, use the VISTA-250FBPT’s features. The following table lists the differences between the VISTA-128FBPT and the VISTA-250FBPT control panels. All other features are identical. Feature VISTA-128FBPT VISTA-250FBPT
2.1 NIST SP 800-18 4 2.2 NIST SP 800-30 4 2.3 NIST SP 800-34 4 2.4 NIST SP 800-37 4 2.5 NIST SP 800-39 5 2.6 NIST SP 800-53 5 2.7 NIST SP 800-53A 5 2.8 NIST SP 800-55 5 2.9 NIST SP 800-60 5 2.10 NIST SP 800-61 6 2.11 NIST SP 800-70 6 2.12 NIST SP 800-137 6 3 CERT-RMM Crosswalk of NIST 800-Series Special Publications 7
Portland Community College Foundation 1,800 Classical Up Close 1,800 Beaverton Civic Theatre 1,800 Experience Theatre Project 1,800 ISing Community Choir 1,800 Oregon Chorale 1,800 Theatre in the Grove 1,800 STAGES Performing Arts Youth Academy 1,800 Aloha Community Farmers Market 1,800
cgt/4-800-3/-1,5 1,5 5,7 3,3 24.780 87 cgt/4-800-3/-2,2 2,2 8,1 4,6 27.520 94 cgt/4-800-3/-3 3 10,7 6,2 32.050 100 cgt/4-800-3/-4 4 -8,1 34.860 101 cgt/4-800-3/-5,5 5,5 - 10,5 36.280 130 cgt/4-800-6/-1,5 1,5 5,7 3,3 18.940 91 cgt/4-800-6/-2,2 2,2 8,1 4,6 23.430 98 cgt/4-800-6/-3 3 10,7 6,2 29.950 104 cgt/4-800-6/-4 4 - 8,1 33.230 105
Calibre 891 PQ 800 Calibre 918 PQ 800 Calibre 923 PQ 800 Calibre 928 PQ 800 Calibre 929 PQ 800 Calibre 960 PQ 800 JAGUAR Base DD 45000 P 800 . Caliber 3220 PQ 650 Caliber 3301 P 650 800 Cal
Airline Phone JFK EWR LGA Airline Phone JFK EWR LGA Icelandair 800-223-5500 n Israir 877-477-2471 n Japan Airlines 800-525-3663 n Jet Blue 800-538-2583 n n n KLM 800-374-7747 n n Korean Air 800-438-5000 n Kuwait Airways 800-458-9248 n Lacsa 800-225-2272 n Lan Chile 800-735-5526
Hilti HIT-1 / HIT-1 CE Concrete Materials Mechanical properties Anchor size M8 M10 M12 M16 Nominal tensile strength f uk HIT-V 5.8 [N/mm²] 500 500 500 500 HIT-V 8.8 800 800 800 800 HIT-V-R 700 700 700 700 HIT-V-HCR 800 800 800 800 Yield strength f yk HIT-V 5.8 [N/mm²] 400 400 400 400 HIT-V 8.8 640 640 640 640
Source: 9th Annual API Cybersecurity Conference & Expo November 11-12, 2014 - Houston, TX. 11 Industry Standards and Committee Initiatives WIB M2784-X-10 API 1164 ISA 99/IEC 62443 NIST SP 800-82 NIST SP 800-12 NIST SP 800-53 NIST SP 800-53A NIST SP 800-39 NIST SP 800-37 NIST SP 800-30 NIST SP 800-34 ISO 27001,2 ISO 27005 ISO 31000
Archaeological Illustration ARCL0036 UCL - INSTITUTE OF ARCHAEOLOGY COURSE NUMBER: ARCL0036 Archaeological Finds Illustration 2018/2019 Year 2, 0.5 unit 15 Credits Co-ordinator: Stuart Laidlaw Co-ordinator's e-mail tcfasjl@ucl.ac.uk Co-ordinator's room number is 405 Telephone number 020 7679 4743 Internal 24743 The Turnitin 'Class ID' is 3884493 and the 'Class Enrolment Password' is IoA1819 .
