SUPPORTS, CANOPY W/CABLE ASSEMBLY INSTRUCTIONS
SUPPORTS, CANOPY W/CABLE ASSEMBLY INSTRUCTIONS KIT P/N 512-00010-00CANOPY SUPPORTS INSTALLATION AND ADJUSTMENTTools required:1 - 7/8” open end wrench1 - 3/4” open or box end wrench(or a rachet and 3/4” socket)2 - 9/16” combination end wrenches1 - TORQUE WRENCHNOTE: READ THESE INSTRUCTIONS CAREFULLYAND COMPLETELY AND UNDERSTAND ALLASSEMBLY AND ADJUSTMENT PROCEDURESPRIOR TO PERFORMING THE INSTALLATIONAND MAKING ANY ADJUSTMENTS. WORKFROM A STABLE LADDER OR PLATFORM WHILEPERFORMING THESE STEPS.THESE INSTRUCTIONS REFER TO THE INSTALLATIONOF THE “SIDE A” ADJUSTMENT BRACKETAND CABLE. THE OPPOSITE SIDE IS INSTALLEDFOLLOWING THE SAME PROCEDURES.64235187INSTRUCTION P/N 612-00010-00ISSUED: 5/21/2015Parts included in kit:ITEMP/NDescriptionQty1001-71017-00FLAT WASHER, 3/8” SAE SS 18-822001-72942-00HHCS, 3/8-16 x 6” FULL THREAD23001-76349-00NUT, 3/8-16 ALUM.44001-76072-00NUT, NYLOCK, 1/2-13 ALUM.65002-00074-00BOLT, CANOPY SUPPORT (FAB)66007-09175-00CABLE, CANOPY SUPPORT 1/4”27111-00421-00WELD’T, CANOPY SUPPORT “SIDE A”18111-00422-00WELD’T, CANOPY SUPPORT “SIDE B”1PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
BRACKET INSTALLATION - PART 11. INSTALL ONE 3/8” NUT (ITEM #3) WHICH WILL BE REFERRED TO ASTHE ADJUSTMENT BOLT LOCK NUT, AND WASHER (ITEM #1) ONTO THE6” ADJUSTMENT BOLT (ITEM #2) AND INSTALL THE BOLT THROUGHTHE HOLE IN THE TOP OF THE VERTICAL TUBE. INSTALL A SECOND3/8” NUT ONTO THE ADJUSTMENT BOLT AS SHOWN IN FIGURE 1.2. INSERT TWO SPECIAL BOLTS (ITEM #5) FIGURE 2 INTO THE SLOT INTHE TOP OF THE CANOPY BEAM, ONE ON EACH SIDE OF CANOPYCROSS BOW NEAR THE VERTICAL CORNER POST – FIGURE 3 & 4.FIG. 13. ROTATE BOLT 90 CLOCKWISE IN CANOPY BEAM SLOT TO LOCKTHE BOLT INTO POSITION.FIG. 2FIG. 3CANOPYCROSSBOWFIG. 42
BRACKET INSTALLATION - PART 2FIG. 54. INSTALL THE RIGHT SIDE SUPPORT BRACKET (“SIDE A” ITEM# 7)OVER THE TWO SPECIAL BOLTS ENSURING THAT THE DIAGONALPART OF THE BRACKET IS FACING FORWARD ON THE LIFT - FIGURE 5.ENSURE THAT THE REAR BOLT IS LOCATED ABOVE THE VERTICALCORNER POST AS SHOWN - IT DOES NOT HAVE TO BE DIRECTLYABOVE, ONLY NEAR.CANOPYCROSSBOWSDIAGONALTUBE5. INSTALL A 1/2” NYLOCK HEX NUT (ITEM #4) LOOSELY ONTO THESPECIAL BOLTS – FIGURE 6.6. ENSURING THAT THE VERTICAL TUBE ON THE SUPPORTBRACKET IS STILL LOCATED ABOVE THE VERTICAL CORNERPOST, TIGHTEN BOTH OF THE NYLOCK HEX NUTS – FIGURE 7.TORQUE TO 60 FT/LBS.REAR BOLTVERTICALCORNERPOSTFIG. 6FIG. 73
CABLE INSTALLATION - PART 17. THREAD THE END OF THE ADJUSTMENT BOLT INTO THE THREADEDCABLE END OF THE ADJUSTMENT CABLE (ITEM #6) UNTIL IT BOTTOMSOUT – FIGURE 8.FIG. 88. TIGHTEN THE 3/8” NUT AGAINST THE END OF THE CABLE ENDUSING 9/16” & 7/8” WRENCHES TO HOLD THE CABLE WHILETIGHTENING THE NUT – FIGURE 9.3/8” NUTCABLEENDFIG. 9ADJUSTMENT BOLT LOCK NUTFIG. 1049. RUN THE 3/8” ADJUSTMENT BOLT LOCK NUT AS FAR BACK AS POSSIBLE TOWARDS THE HEAD OF THE ADJUSTMENT BOLT – FIGURE 10.
CABLE INSTALLATION - PART 210. ROUTE THE ADJUSTMENT CABLE ON THE INSIDE OF THE CANOPYCROSS BOWS AS FAR FORWARD AS POSSIBLE – FIGURE 11.CROSS BOWSCABLE RUNS INSIDEALL CROSS BOWSFIG. 1111. INSERT A SPECIAL BOLT INTO CANOPY CHANNEL NEAR THE ENDOF THE ADJUSTMENT CABLE AND ROTATE IT 90 TO LOCK IT INTO THECANOPY CHANNEL – FIGURE 12.FIG. 1212. MAKING SURE THAT THERE ARE NO TWISTS IN THE ADJUSTMENTCABLE, INSTALL THE CABLE OVER THE SPECIAL BOLT AND INSTALL A1/2” NYLOCK NUT ONTO THE BOLT – FIGURE 13.FIG. 135
CABLE INSTALLATION - PART 313. PULL THE ADJUSTMENT CABLE AS FAR FORWARD ASPOSSIBLE AND TIGHTEN THE NYLOCK NUT ENSURING THE CABLEEND IS PARALLEL WITH THE CANOPY CHANNEL – FIGURE 14 A & B.TORQUE TO 60 FT/LBS.FIG. 14AFIG. 14B14. TIGHTEN THE CABLE BY HOLDING THE HEX END OF THEADJUSTMENT BOLT WITH ONE 9/16 WRENCH WHILE TIGHTENINGTHE ADJUSTMENT BOLT LOCK NUT WITH A 9/16 OPEN END WRENCH– FIGURE 15.FIG. 156
CABLE ADJUSTMENT15. TIGHTEN THE CABLE UNTIL THERE IS NO PERCEIVABLEDOWNWARD BOW IN THE CANOPY BEAM – FIGURE 16 A & B.NOTE: IF YOU RUN OUT OF ADJUSTMENT THREAD WHILETIGHTENING THE CABLE, BACK OFF THE ADJUSTMENT SCREW ALLTHE WAY (AS SHOWN IN FIGURE 11) AND MOVE THE FORWARDEND OF THE CABLE FURTHER FORWARD. RETIGHTEN AND MAKEADJUSTMENTS ACCORDING TO THE PREVIOUS STEPS.FIG. 16A16. DO NOT OVER-TIGHTEN THE CABLE.FIG. 16B REPEAT STEPS 1 THROUGH 17 TO INSTALL THE ADJUSTMENT BRACKET AND CABLE ON THE OPPOSITE SIDEOF THE CANOPY FRAME. AFTER INSTALLATION, CHECK THE CABLE PERIODICALLY TO ENSURE THAT IT IS STILL TIGHT AND THAT ALLHARDWARE IS SECURE. RE-ADJUST AND RE-TIGHTEN IF NECESSARY.7
Want the best? Go with the FLOE!FLOE INTERNATIONAL, INC.48473 STATE HIGHWAY 65 McGREGOR, MN 55760218-426-3563www.floeintl.comAll material copyright 2015 FLOE International, Inc. Unauthorized reproduction is strictly prohibited.Specifications subject to change without notice.5/15
SUPPORTS, CANOPY W/CABLE ASSEMBLY INSTRUCTIONS KIT P/N 512-00010-00 1 - 7/8” open end wrench 1 - 3/4” open or box end wrench (or a rachet and 3/4” socket) 2 - 9/16” combination end wrenches 1 - torQUe wrench tools reQUired: item p/n description Qty 1 001-71017-00 FLAT WASHER, 3/8” SAE SS 18-8 2 2 001-72942-00 HHCS, 3/8-16 x 6” FULL .
CANOPY TYPE (see images below) CANOPY COLOR HARDWARE CABLE OR STEM LENGTH 5 5" round canopy W White AC Air Craft Cable 18 18 inches 5S 5" square canopy A Aluminum SW Stem white 24 24 inches SCD Square canopy driver box B Black SA Stem aluminum 36 36 inches RCD Round canopy driver box ####
Canopy structure was estimated from discrete return and waveform ALS data. New models were developed based on the Beer-Lambert law to relate canopy volume to the fraction of laser light reaching the ground. Waveform ALS data (canopy volume RMSE 27.6%) described canopy structure better than discrete return ALS data (canopy volume RMSE 36.5%).
- The use of montana tropical forest canopy by bird species 455 Figure 3. The space division layer of forest canopy in use by birds (Pearson 1971) Figure 2. The space division of the tree canopy layer in its use by birds (Pearson 1971). Note: Axis X wide canopy (m); Axis Y canopy height (m); Position I: if the bird occupies the space at the
Piper Seneca PA-34 Canopy Cover Piper PA-44 Seminole Canopy/Nose Cover Description Part Number Price CANOPY COVER PA44-000 570.00 CANOPY/NOSE COVER PA44-005 880.00 EXTENDED CANOPY COVER PA44-010 725.00 EXTENDED CANOPY/NOSE COVER PA44-011 1180.00 NOSE COVER PA44-110 455.00 Section 2: Engine/Prop Covers
sonoma coronado swing assembly instructions assemble on a flat, protected surface style #: middle leg crossbar. top frame bar. canopy side bar: canopy back support crossbar canopy side support crossbar: canopy center support crossbar canopy front support crossbar: long hanging bar front leg:
Catalogue 2020-21 Life Line Plus S3 (HRFR) Cable Life Guard (FR-LSH) Cable Life Shield (HFFR) Cable Multicore Round Cable Shielded Cables Flat Submersible Cable Telephone Switch Board Cable LAN Cable CCTV Cable Co-Axial TV Cable Speaker Cable Presenting Domestic Cable Range for Safer, Securer Homes.
instrumentation tray cable 10 general purpose cable 12 instrumentation tray exposed run direct burial cable 14 power tray exposed run direct burial cable 16 industrial ethernet cable 18 fieldbus technology cable 20 extremelife cable 22 flexlife cable 24 weldlife cable 26 armorfast instrumentation cable 28 flexible service cable
6 Cable Ladder and Cable Tray Systems– Including Channel support Systems and other Associated Supports Definitions and Abbreviations Accessory Component used for a supplementary function e.g. to join two components together, clamp or fix to walls, ceilings or other supports, covers and cable retainers Associated supports Bespoke supports for cable tray and cable ladder other than BS 6946 channel
