Infiniti Service Bulletin - AutoCodes
ugust 28, 20062004-2005 FX35 AND G35; MIL "ON" WITH DTC P1031, P1051, P1148, P1168ITB04-027 has been amended and supersedes ITB04-023 Please discard all previous versions of these bulletins.APPLIED VEHICLES:APPLIED VINS :APPLIED DATES:IF YOU CONFIRM:2004-2005 FX35 (S50) and G35 (V35)G35 Sedan 2WD After JNKCV51E(*)4M6000001G35 Sedan 4WD After JNKCV51F(*)4M7000001G35 Coupe After JNKCV54E(*)4M8000001FX35 2WD After JNRAS08U(*)4X105001FX35 4WD After JNRAS08W(*)4X210001Vehicles built After October 2003.A MIL “ON” with the following DTC(s) stored:On 2004 MY vehicles ONLY P1031 / P1051 (A/F Sensor Heater),and/or P1148 / P1168 (A/F Sensor Closed Loop Control),On 2005 MY vehicles ONLY P1148 / P1168 (A/F Sensor Closed Loop Control),ACTIONS:Step A: Use Consult II to confirm this bulletin applies: Check the Current ECM Part Number (see page 2). Perform A/F Sensor test to confirm proper air fuel operation (see page 3).If the A/F sensor fails the test this bulletin does not apply. Go back to ASIST for further repairinformation. Compare your Current ECM Part Number to Chart A on page 3.If that part number does not match one in Chart A, this bulletin does not apply. Go back toASIST for further diagnostic and repair information.Step B: If this bulletin applies, reprogram the ECM (see page 4).IMPORTANT: The purpose of "ACTIONS" (above) is to give you a quick idea of the work you will beperforming. You MUST closely follow the entire Service Procedure (starting on page 2) as it containsinformation that is essential to successfully completing this repair.Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trainedindividuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believethat a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti dealer to determine if thisapplies to your vehicle.1/8
CLAIMS INFORMATIONSubmit a Primary Failed Part (PP) line claim using the following claims coding:DESCRIPTIONReprogram ECM per TSBPFP(1)OP CODESYMDIAFRTDE98AAHD320.8 hrs(2)(2)(1) Reference the final CONSULT-II print out and use the indicated new ECM P/N as the PFP.(2) FRT allows adequate time to access DTC codes, reprogram ECM and perform the A/F Sensor function test.No other diagnostic procedures subsequently required – do NOT claim any Diagnostic Op Codes with thisclaim.SERVICE PROCEDUREStep A: Confirm This Bulletin Applies1. With CONSULT-II “ON”, print the Freeze Frame data as follows:START(Nissan) ENGINE Self-DIAG Results F.F. Data PRINTSYSTEMDATEP/#2. Attach this printout to the Repair Order. Figure 1 is an example of the F.F. Data printout.ENGINEXX/XX/XXXX* xx:xx:xxCurrent23710-XXXXXECM PartNumberFreeze Frame The Freeze Frame data that you’ve printed containsthe ECM Part Number (P/N).The ECM part number will be used to see if thisbulletin applies or not.DTCCodeDTC RESULTS(DTC description here)[P0XXX]* Example, your screen may differ.Figure 12/8TP020389k
3. Use CONSULT-II DATA MONITOR to view; Engine Speed, and A/F Sensor voltage (see Figure 2).4. Hold the engine speed at about 2000 rpm no-loadfor 2 minutes. This will create a stable condition forstep 5 (below).Figure 25. Observe A/F SEN1 (B1) and A/F SEN1 (B2) voltage for 30 seconds while holding 2000 rpm no-load.a. During most of this test, the A/F sensor voltages should remain between 1.37 and 1.57 volts.NOTE: If the engine rpm is held constant, voltage will fluctuate (change), but should remain in thisrange. If the A/F sensor voltages are out of this range for most of the test, this bulletin does not apply.Go back to ASIST for further diagnostic and repair information. If the A/F sensor voltages are OK proceed to step 6.6. Check the ECM Part Number on the printout you made in Step 1. Compare your vehicle's ECM P/N to those shown under Current ECM P/N inChart A, below:Chart AVehicleFX35G35 SedanG35 CoupeCURRENT ECM P/NVehicle/model Configuration2WD2WD, ICC4WD4WD, ICCA/T with 2WDA/T with 4WD (AWD)M/T with 5AC710AC800AC810A. If your vehicle’s ECM P/N matches a P/N in the chart above: Go to Step B : ECM Reprogramming.B. If your vehicle’s ECM P/N does not match a P/N in the chart above: This bulletin does not apply. Go back to ASIST for further diagnostic and repair information.3/8
Step B: ECM REPROGRAMMINGVehicle ECM Reprogramming Overview There are four basic steps (tasks) under Step B:1. Download reprogramming data (transfer it) from ASIST into CONSULT-II.2. “Preparation” steps before reprogramming.3. Reprogram the vehicle ECM.4. ECM Reprogramming “Wrap-up”.NOTE: If you’re not familiar with the latest ECM reprogramming procedures, click here.This will link you to the "ECM Reprogramming For Infiniti Vehicles" general procedure. For those familiar with ECM Reprogramming, please review the following steps and use them as a QuickReference for ECM reprogramming.4/8
Step One: Download (Transfer) Data From ASIST Into CONSULT-IIVehicle /ModelConfiguration* Click the "Add" buttonQ452004M452003I352002I302001G352000G2019991 File(s) selectedVehicle Configuration #1UsedSpace16MBTo 23710-XXXXX Engine #1, Trans #1, etcTo 23710-XXXXX Engine #1, Trans #1, etc.To: 23710-XXXXXVehicle Configuration #2"To"NumberTo 23710-XXXXX Engine #1, Trans #1, etc.To 23710-XXXXX Engine #1, Trans #1, etc.Vehicle Configuration #3To 23710-XXXXX Engine #1, Trans #1, etc.QX56Details:FXAddReplaces 23710-XXXXX, -XXXXXQX48MBRemoveMoreMoreSearch by Code(per bulletin only)KeyPadBackUpShow meMainMenuContinueThis illustration is for example only, your vehicle may be different.TP030621JFigure A1. Select vehicle model and model year (Example: FX35, 2004).2. Select the correct reprogramming data:a. Locate the specific “Model Configuration” (Example: VQ35, A/T, 2WD).NOTE: Model Configuration may include items such as engine type, transmission type, and vehicleoptions such as ASCD, TCS, and ABS etc.b. Select (click on) the “To” number.NOTE: The “To” number will read: 23710-XXXXX.3. Click on the “Add” button. This will add the data you selected to the “File(s) Selected” list.4. Write the “To” number on the Repair Order.5. Click on “Continue” and follow directions to perform “data transfer” (download) from ASIST intoCONSULT-II.5/8
Step Two: Preparation for Reprogramming ECM1. Connect a battery charger to the vehicle's battery. Set the charger to a low charge rate (trickle charge).Do Not Connect A/C Power SupplyConsult-II A/CPower SupplyCAUTION: For number 2 below and number 3on the next page, DO NOT connect theCONSULT-II A/C Power Supply.TP040090Figure BNISSANELECTRONIC CONTROL UNITREPROGRAMMING2. Press SUB MODE (see Figure C) then:AER02C-1a. From the listed items, find and selectBATTERY CHARGE.INITIATE ECU REPROGRAMSUB MODELIGHTCOPYTP030620Figure C6/8
3. Check the CONSULT-II’s “Charger Input”reading (see Figure D).Battery ChargingCONSULT-IIBatteryVoltageNOTE: DischargeCharge Time00.00:0000:01.02Battery VoltageCharger Input8.32 12.15“Battery Voltage” is the voltage level ofCONSULT-II's battery. Elapsed00:01.020%0MUST BEABOVE12.00 VOLTS!100%1020 3040 5060 7080 90 100Battery Charge - IDLE"Charger Input" is the voltage level of thevehicle’s battery. (It must be above ck ChargerInput withoutAC powersupplyconnected.Discharge &ChargeBACKLIGHTCOPYTP030625Figure DCAUTION: If the “Charger Input” is below 12 volts: A list of items to check when “Charger Input” voltage is below 12V is contained in the "ECMReprogramming For Infiniti Vehicles" general procedure. Click here. to link to it.Step Three: Reprogram the ECM If you are not familiar with ECM Reprogramming, click here.: This will link you to a general procedure called "ECM Reprogramming For Infiniti Vehicles."7/8
Step Four: “Wrap-up” After Reprogramming is finished1. Turn the ignition switch "OFF" and CONSULT-II “OFF”.2. Wait more than 10 seconds, then;a. Turn the ignition switch "ON" for 2 second, thenb. Turn the ignition switch "OFF" again for 10 seconds (see Figure E). This will reset ECM “self learned” Data.Ignitionkey "ON"2 Sec.2 Sec.Ignitionkey "OFF"10 Sec.10 Sec.TP030626bFigure E3. Start the engine and check the idle speed. If idle speed is too low, perform Idle Air Volume Learning (IAVL). See the appropriate Service Manual(ESM) for this procedure.NOTE: If the engine will not idle, hold the engine RPM at about 2000, then slowly bring it down to anidle. IAVL can now be performed.4. Confirm the engine is operating normally.5. Make sure the MIL is OFF. If the MIL comes ON, use CONSULT-II with the Diagnostic (red/white) Card to erase any DTC’s thatmay have stored during the reprogramming procedure.8/8
Q45 M45 I35 I30 G35 G20 QX56 FX QX4 2004 2003 2002 2001 2000 1999 Search by Code (per bulletin only) . (IAVL). See the appropriate Service Manual (ESM) for this procedure. NOTE: If the engine will not idle, hold the engine RPM at about 2000, then slowly bring it down to an idle. IAVL can now be performed. . Infiniti Service Bulletin
2003-2007 Infiniti G35 2D Coupe VS Style Rear Spoiler 4 000 5 100 7 500 YCING35003 2003-2007 Infiniti G35 2D Coupe DTM Style Rear Diffuser 2 900 YCING35004 2003-2007 Infiniti G35 2D Coupe Front Grille 2 000 YCING35006 2003-2007 Infiniti G35 2D Coupe
Your INFINITI retailer's name. Your comments or questions OR You can write to INFINITI with the informa-tion on the left at: For U.S. customers INFINITI Division Nissan North America, Inc. Consumer Affairs Department P.O. Box 685003 Franklin, TN 37068-5003 or via e-mail at: nnaconsumeraffairs@nissan-usa.com For Canadian customers INFINITI .
ment to 2017 Infiniti Warranty Information Booklet & 2017 Infiniti Owner’s Manual for possible exceptions applying inyour state. ASSISTANCEOUTSIDEOFWARRANTY In support of our commitment to the “Total Ownership Experience,” Infiniti may occasionally offer to pay or
FOREWORD Thank you for purchasing an INFINITI vehicle. This user's manual is for INFINITI InTouchTM and the systems linked to INFINITI In-TouchTM offered in your INFINITI vehicle. Operation instructions for the following
availability, additional options or accessories, contact your INFINITI dealer. All specifications, options and accessories shown in this guide apply to the 49 continental states. Specifications, options and accessories may differ in Hawaii, U.S. territories and other countries. INFINITI, the INFINITI logo, and INFINITI model names are Nissan .
availability, options or accessories, see your INFINITI Retailer or visit INFINITI Final production vehicle may vary. Always wear your seat belt, and please don t drink and drive. 2018 INFINITI. IN-21570 Reorder #19502i (3/18, 50K, CG) Reducing our environmental footprint is an important goal at INFINITI. That s why this brochure uses paper
- Your INFINITI dealer's name - Your comments or questions OR You can write to INFINITI with the information on the left at: For U.S. customers INFINITI Division Nissan North America, Inc. Consumer Affairs Department P.O. Box 685003 Franklin, TN 37068-5003 For Canadian customers INFINITI Division Nissan Canada Inc. 5290 Orbitor Drive
three main factors used for determining the premium rates under a life insurance plan are mortality, expense and interest. The premium rates are revised if there are any significant changes in any of these factors. Mortality (deaths in a particular area) When deciding upon the pricing strategy the average rate of mortality is one of the main considerations. In a country like South Africa .
