FLAT TRACK SLIDING BARN DOOR HARDWARE Face Mount .

FLAT TRACK SLIDING BARN DOOR HARDWAREFace Mount Installation Instructions

GeneralInfo- The wall or structure that your system will bemounted on must be designed to support amaximum door weight of 400 lbs.- Ensure that door panels are constructedwith solid, structural material.- Do not install directly into drywall. Must beinstalled into wall blocking or header board.- Check with your contractor and/or your cityof residence to confirm accordance withlocal building codes.- For best results, seek qualified buildingprofessionals for �AllenWrench

What’s inthe boxHangersTrack FastenersHangerBoltsStopsAnti-jumpsFloor GuideDrywallAnti-crushesPost & SpacersTrackSplice Kit (Required for 10’, 13’ or 16’ Lengths)BracketSplice kitscrewsOptional Soft Open/CloseSoft Open/CloseCatch

1Mark for TrackUse the track as a template to mark the center of the holes.Tracks with splice kits have a unique hole spacing between splice.Header board*Internal bracing!Do not installdirectly intoDrywall. Mustattach to a preinstalled headerboard or the wallmust be bracedinternally.*Header board and anchor screws not included.Center Lineof trackmounting holesTrack height door panel height 2-1/4”Install track splice(required for 10’, 13’, 16’ lengths)4

2Install Optional Soft Open/Close - Part 1!Mount the soft open/close on thebottom of the track and ensure that itis oriented in the correct direction foroperation.Direction of doorDirection of door5

3Secure TrackDrill 19/64” [7.54mm] pilot holes in marked locations for trackfasteners.Attach track to wall using track brackets and fasteners as shown.!Use supplied anti-crush discs if installing to an internallybraced wall. NEVER attach directly to drywall.Use 5/16” AllenWrench to installtrack screwsUse supplied spacers asnecessary to ensure that thedoor has clearance from wall/moldings.6

4Prep Door for Hangers & Floor Guide19/32[15.1]Drill Holes in door forhanger bolt by using a19/32” bit.1 1 " 38.1243"4120.75 15.888"716 "11.11Route bottom, full lengthof door to receive floormounted guide.7

5Install Anti-JumpInstall anti-jump flushto front of door.Front of door6Mount Hangers to DoorTip: You may need to counterborethe back of the door for thick doorapplications.Back of doorUse 7/32” AllenWrench to installtrack screws8

7Hang the DoorPrior to hanging door on track rotate anti-jump toward front face ofdoor as shown to disengage.9

810Adjust the StopsTighten set screws. Start with bottom set screws then move to topset screws with sufficient force to drive set screws into bar after finaladjustment. Ensure the stops allow for the door to extend the desiredlength over the door opening. Adjust stops accordingly.

9Install Floor GuideDrill pilot holes for anchors using 11/32” drill bit. Mount floor guidewith anchors and screws provided.WallTip: Install floor guide in a position where it won’t be exposedwith door in the open or closed position.11

10Install Optional Soft Open/Close - Part 21. Move door to desired stop location.2. Place soft catch under soft open/close as shown.3. Mark location of soft catch.4. Remove door from track5. Install soft catch at marked location6. Hang door on trackIN4-BARNFACEMNTREV 1 10-06-20Copyright 2020, EMTEK Products, Inc. an ASSA ABLOY Group company. All rights reserved. Reproduction inwhole or in part without the express written permission of EMTEK Products, Inc. is prohibited.! WARNING: This product can expose you to chemicals including lead, which is known to the state of California tocause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

FLAT TRACK SLIDING BARN DOOR HARDWARE Face Mount Installation Instructions. 19/32” 11/32” 19/64” 1-1/2” .