LHS Hydraulic Heavy-Duty Actuator Series
TECHNICAL BULLETINLimitorqueTMLHS Hydraulic Heavy-Duty Actuator SeriesFCD LFENTB0003-00-A4 - (11/14)Experience in Motion
Limitorque LHS Hydraulic Heavy-Duty Actuator Series FCD LFENTB0003-00-AQ - 11/14ContentsLHS Series Hydraulic Heavy-Duty Actuator Specifications.4Actuator Selection Table.6Actuator Selection Guidance.61 Scope.62 General Definitions/Terms Used.63 Inputs for Sizing Hydraulic Scotch Yoke Actuators.74 Selection.85 Single Action and Double Action Configurations.106 Performance Data.117 Dimensions.118 Disclaimer.11Torque Charts – Single Acting Fail Close - Imperial and Metric.12Torque Charts – Single Acting Fail Open - Imperial and Metric.28Torque Charts – Double Acting - Imperial and Metric.36Dimensional Data and Weights – Single Acting.39Dimensional Data and Weights – Double Acting.50Mounting Interface Dimensions.52Service Kits.532
Limitorque LHS Hydraulic Heavy-Duty Actuator Series FCD LFENTB0003-00-AQ - 11/14TablesFiguresTorque Charts — Single Acting Fail Close — Imperial and MetricFigure 1: Actuator OPEN (by hydraulic) Torque Curve:LHS-15A – Symmetric. 12 13Single Acting Spring Return – Fail Close (CW).7LHS-15C – Canted. 14 15Figure 2: Actuator CLOSE (by spring) Torque Curve:LHS-20A – Symmetric. 16 17Single Acting Spring Return – Fail Close (CW).8LHS-20C – Canted. 18 19Figure 3: Single Acting Actuator Configuration:LHS-25A – Symmetric. 20 23Fail Close – Fail Clockwise.10LHS-25C – Canted. 24 27Figure 4: Single Acting Actuator Configuration:Fail Open – Fail Counterclockwise.10Torque Charts — Single Acting — Imperial and MetricLHS-15A – Symmetric. 28 29LHS-20A – Symmetric. 30 31LHS-25A – Symmetric. 32 35Torque Charts — Double Acting — Imperial and MetricLHS-15A – Symmetric.36LHS-15C – Canted.36LHS-20A – Symmetric.37LHS-20C – Canted.37LHS-25A – Symmetric.38LHS-25C – Canted.38Torque Data and Weights — Single Acting . 39 49Torque Data and Weights — Double Acting . 50 51Figure 5:Double Acting Actuator Configuration – Close Position.10Figure 6:Double Acting Actuator Configuration – Open Position.11Figure 7:Dimensional Data – Single Acting – Sym/Cant – Fail Close.39Figure 8:Dimensional Data — Single Acting — Sym/Cant — Fail Open.39Figure 9: Dimensional Data – Double Acting – Sym/Cant .50Figure 10: Single Acting Actuator.53Figure 11: Spring Can Exploded View.53Figure 12: Exploded View of Hydraulic Cylinder.54Figure 13: Exploded View of Housing.55Figure 14: Exploded View of Adaptor Kit.55Mounting Interface Dimensions.52Service Kits. 53 55flowserve.com3
Limitorque LHS Hydraulic Heavy-Duty Actuator Series FCD LFENTB0003-00-AQ - 11/14LHS Series Hydraulic Heavy-Duty Actuator Specifications1.The LHS range of Limitorque Hydraulic Actuators is a robust,modular scotch yoke design, available in both spring return anddouble acting configurations. It is suitable for actuating ball,butterfly and plug valves or any other quarter-turn application.2.LHS Hydraulic actuators deliver up to 250 kNm* (184 000ft-lb) of precisely controlled torque. LHS Limitorque HydraulicActuator is enlarging the recent Limitorque Fluid PowerSystems family of heavy-duty scotch yoke actuators. The samedesign philosophy introduced on heavy-duty LPS actuatorshas been adopted for the LHS range, bringing enhancedperformance and reliability.3.4.5.LHS actuators are complemented by a comprehensive rangeof accessories, such as lockout modules, manual overridesand controls, like hydraulic power units, accumulator racks,self-contained units and other electro-hydraulic solutions. TheLimitorque engineering team can also design custom solutionsfor the largest and most complex customer requirements.Limitorque provides engineering design services for mountinghardware, ensuring that your actuation solution is ready tohandle the toughest challenges.The LHS actuator is designed to provide a 25-year design life,depending on service conditions, proper installation, operationand maintenance. In order to achieve this industry–leadingdesign life, in-field maintenance is prescribed to be performedevery 6 years of operation. For high-cycle applications, suchas control valve operation, more frequent maintenance ofreplaceable wear surfaces, as outlined in EN 15714, may berequired.6.Suitable for use in on/off, modulating and control valveapplication in general service, protective service and safetyapplications such as ESD or HIPPS.7.Available valve interface in compliance with ISO 5211or MSS SP-101, upon request as an option.8.Manufactured and tested in compliance with EN 15714-4and ISO 12490.9.Spring components are designed in compliance withEN 13906-1.10. Surface coating and corrosion protection in compliance withISO 12944-2 up to and including C5-M if requested.11. Environmental resistance has been certified to meet or exceedthe requirements of IEC 60529 up to and including IP-67M.* contact factory for larger sizes and higher output torques412. The LHS actuator is suitable for use in Safety IntegratedSystems in accordance with IEC 61508 up to and includingSIL Level 3.13. The actuators in the LHS series meet the requirements ofISO 5599-2.14. LHS actuators are available in accordance with ATEX 94/9/ECEx II 2GD c IIC T6, as it relates to mechanical actuators.15. Actuators are available in compliance with NACE specificationMR0175 for sour gas applications16. Shaft-driven accessories/devices are directly mounted toVDE VDI 3845 NAMUR compliant mounting locations.17. The actuator is manufactured and tested in compliance with anISO 9001 Quality Assurance Program.18. Integral travel stops provide 90 5 of stroke adjustmentand are designed for the MAWP of the actuator up to 207 barg(3000 psig). MAWP 345 barg (5000 psig) version uponrequest.19. The materials of construction and seals of the LHS familyof actuators are available for a wide range of servicetemperatures, including Tropical, Arid, Temperate, Cold andPolar regions in accordance with IEC 60721.20. The hydraulic cylinder design features proven and reliableexternal tie rods suitable for continuous duty service at themaximum rated pressure. Wear and corrosion protection of allcomponents is ensured with suitable treatments and coatings.ENP (electro less nickel plating) is the standard for the internalsurface of the hydraulic cylinder to ensure complete sealingand superior corrosion resistance. Other coatings for theinternal surface of the cylinder are available upon request. TheLHS actuator cylinders are capable of being independentlytested prior to assembly.21. Pressure modules are available in compliance with:a. Pressure Equipment Directive 97/23/ECb. ASME BPVC Sec. VIII, Div. 1c. EN 13445-3, Part 3 for Unfired Pressure Vessels22. All actuators and modules meet acceptance criteria defined byFlowserve test specifications.23. The actuator is provided with two full-length key slots inthe yoke suitable for mounting in alternate orientations(horizontally or vertically – parallel or perpendicular to thepiping system).
Limitorque LHS Hydraulic Heavy-Duty Actuator Series FCD LFENTB0003-00-AQ - 11/1424. The LHS is available with either a symmetric or canted scotchyoke. Scotch yoke cants are available from 1 to 15 uponrequest, pending on application.25. All modules align and mate with close-tolerance machinedflanges with no exposed threaded connections.26. The high-strength, heat-treated alloy steel guide bar is hardchrome plated for wear and corrosion protection.27. Piston rods are designed to handle lateral loads to effectivelyminimize deflection. The piston rod is detachable from thetorque module without special tools and does not requiremodule disassembly.28. Pressure seals utilize O-rings, quad-rings or V-rings asappropriate to eliminate environmental ingress. No gaskets areused in pressurized regions of the actuator.29. The push-to-compress springs are safely enclosed and weldedand are positively retained on the torque module under all loadconditions. No external tie rods/braces are required to containthe springs. Springs are designed in accordance withEN 13906-1 and combined and positioned to eliminatepotential contact with the container or each other in the caseof multiple springs. Springs are shot peened for maximum lifeand are painted and permanently lubricated coated prior toassembly to eliminate corrosion.30. The spring and spring guide are self-centered and bearingguided within the spring module. The spring rod is guided ina self-lubricating bearing and connected to the torque modulethrough a large pinned connection designed for safe operationat all load conditions. Installation and removal of the springmodule does not require special tools.31. Maintenance-free, self-lubricating bearings are used tominimize friction of the yoke, yoke-pins and slider blocks in theyoke slots for low friction and to minimize contact stresses inorder to provide the longest possible service life.32. Retention of the yoke pin is by a single plate to permit easyremoval of the yoke pin and slider blocks while the actuator ismounted in the valve. No specialized tools are required.flowserve.com5
Limitorque LHS Hydraulic Heavy-Duty Actuator Series FCD LFENTB0003-00-AQ - 11/14LHS ACTUATORActuator Selection TableLHS SELECTION TABLEC30354065Seals MaterialCodeMaterialBBunaVViton Climate Classificationaccording to IEC60721Temperature RangeStd Temp: -29 C to 100 C (-20 F to 212 F)Hi Temp: up to 160 C(320 F)SSiliconLow Temp: down to-40 C (-40 F)ZOtherSpecial Applications:Consult Factory758085B - BUNAV - VITON *-FC 1-1FC - FAIL CLOSE1-1FO - FAIL OPEN1-2S - SILICONZ - SPECIAL90100example model n D1 - 1 CYLINDER D.A.D2 - 2 CYLINDER D.A.DD - 2 CYLINDERS TANDEMSPRING CAN SIZEB090YSINGLEACTINGA-DOUBLEACTING2515XHYDRAULIC CYLINDER SIZEYOKE TYPEHOUSING SIZE1520-SEAL 3-12203-22403-32603-42803-54-14-2Tropical & Arid4-34-4TemperateCold & Polar4-5Actuator Selection Guidance1. ScopeThis section provides guidance for the selection of the properLHS actuator to suit specific operational requirements. A basicunderstanding of scotch yoke actuators and the typical applicationsin which they are used is provided in order to assist in selectionof the most suitable actuator. While the selection procedures andproduct data contained herein cover many applications, due to thewide range of applications in which the LHS actuators can be used,this information will not cover every set of operational requirements.The Limitorque applications team is always available to assessspecific applications and help with selection of the appropriate LHSactuators. Please contact your local office for assistance.2. General Definitions/Terms UsedQuarter-turnA device that rotates by a nominal 90 . LHS series actuators rotate 5º more than the nominal 90 .PositionThe degree of rotation describing an actuator’s current location, the zero being referred from completecounter-clockwise position of the yoke. The mid-position of the actuator is at 45 and 90 being the endof clockwise stroke.CWClockwise rotation.CCWCounter-clockwise rotation.StrokeA continuous, 90 rotation of a quarter-turn actuator.CycleTwo strokes, one clockwise (CW) rotation and other counter-clockwise (CCW) rotation, constitute onecycle of operation of the actuator.*Viton is a registered trademarks of E. I. du Pont de Nemours6
Limitorque LHS Hydraulic Heavy-Duty Actuator Series FCD LFENTB0003-00-AQ - 11/14Safety FactorA factor multiplied by the valve’s basic required torque value to increase the amount of torque required tomeet safety requirements in a given application. When the valve’s torque requirements are not known withcertainty, or due to other application demands, use of a safety factor is required in the selection processin order to meet the worst-case torque requirements.Hydraulic Break TorqueOutput torque when the actuator is in the position to start the pressure stroke. [The torque required toinitiate the pressure stroke.]Hydraulic End TorqueOutput torque at the end limit of the pressure stroke. [The torque required to seat the valve at the end ofthe pressure stroke.]Run TorqueThe output torque recorded while the actuator is in the mid-position of the pressure stroke (45 ). Forsymmetrical yoke double-acting actuators, this is the minimum torque output obtained during thecomplete stroke.Spring Break TorqueThe output torque when the actuator is in the position to start the spring stroke. [The torque required toinitiate the spring stroke.] The spring is fully compressed at this position and generates the maximumspring force.Spring End TorqueThe output torque when the actuator has reached the end limit of spring stroke. [The torque required toseat the valve at the end of the spring stroke.] The spring is fully extended at this position and generatesthe minimum spring force.Minimum TorqueThe output torque at an intermediate position of the spring stroke, where the output torque of the actuatoris at its lowest value.MOPMaximum operating pressure of an actuator3. Inputs for Sizing Hydraulic ScotchYoke ActuatorsDue to the scotch yoke mechanism, LHS actuators have a particularU-shaped output torque curve whether powered by a fixed supplypressure or the spring.For a proper actuator model selection, the safety factors betweenactuator output torque and valve torque requirement shall becalculated at least in six points along the valve stroke. In addition afinal check is necessary to guarantee that actuator Maximum OutputTorque does not exceed valve Maximum Allowable Stem Torque(MAST).Figure 1: Actuator OPEN (by hydraulic) Torque Curve: Single Acting Spring Return – Fail Close (CW)flowserve.com7
Limitorque LHS Hydraulic Heavy-Duty Actuator Series FCD LFENTB0003-00-AQ - 11/14Figure 2: Actuator CLOSE (by spring) Torque Curve: Single Acting Spring Return – Fail Close (CW)Note: Detailed Output Torque graphs covering the full valvestroke for both Single Acting Fail Open (CCW) and Double Actingactuators are available upon request.The minimum set of parameters and features necessary for anoptimized actuator selection: Valve torques, or at least the unseating torque (BTO), andvalve MAST Type of actuator: Single Acting/Spring Return: Fail Safe Close (CW)or Fail Safe Open (CCW) Double Acting configuration for Fail Last or Fail As Is Minimum, Normal and Maximum Hydraulic Supply Pressureto the actuator Safety Factors requested by the project or by a specificapplication Working Temperature range Open/Close stroking times Additional options (manual override, control panel, limitswitch box, positioner, )8Definitions:BTO Break to Open torqueBTC Break to Close torqueRTO Running to Open torqueRTC Running to Close torqueETO End to Open torqueETC End to Close torqueMAST Maximum Allowable Stem TorqueSF Safety Factor
Limitorque LHS Hydraulic Heavy-Duty Actuator Series FCD LFENTB0003-00-AQ - 11/144. SelectionThe most common application of clockwise rotation to close avalve is considered for these selection examples.The start to open or hydraulic break torque of the valve (BTO) isconsidered the maximum required torque by the valve. An actuatorshall exceed the valve torque requirement at all positions of therotation. The start/end and minimum torque output for a doubleacting actuator are given in the charts. For spring-return actuators,the spring and the hydraulic strokes’ lowest start/minimum/endoutput torque values are given in the charts.4.1. Double-Acting Actuator Selection4.1.1. Select the operating pressure column that is equal toor less than the known minimum operating pressure.Look up the start/end and minimum torque values, under the selected pressure column, that exceed the valve’smaximum requirements.4.2.5. Refer the performance data table to ensure the maximumsupply pressure to the actuator does not exceed the MOP ofthe actuator.4.2.6. If the maximum supply pressure exceeds the MOP, it may berequired to use a pressure-regulating device at the inlet tothe actuator or an alternate actuator model may be selectedthat is rated for a higher MOP.4.3. Spring-Return, Fail-CCWActuator Selection4.3.1. From the spring torque column, locate the spring starttorque value that exceeds the valve’s maximum unseatingtorque requirement (Fail-Open application).4.1.2. Locate the actuator model corresponding to the selection.4.3.2. Moving to the right along that row, locate the column corresponding to the minimum operating pressure available to theactuator and read the pressure stroke end torque.4.1.3. Refer the performance data table to ensure the maximumsupply pressure to the actuator does not exceed the MOP ofthe actuator.4.3.3. The hydraulic end torque at the minimum available pressuremust be higher than the valve’s seating torque requirement(torque to fully close the valve).4.1.4. If the maximum supply pressure exceeds the MOP, it may berequired to use a pressure-regulating device at the inlet tothe actuator or an alternate actuator model may be selectedthat is rated for a higher MOP.4.3.4. The hydraulic start torque must exceed the valve’s torquerequirement at this position to close the valve in the CWdirection.4.2. Spring-Return, Fail-CWActuator Selection4.2.1. From the spring torque column, locate the spring end torquevalue that exceeds the valve’s maximum seating torquerequirement.4.3.5. Refer to the performance data table to ensure the maximumsupply pressure to the actuator does not exceed the MOP ofthe actuator.4.3.6. If the maximum supply pressure exceeds the MOP, it may berequired to use a pressure-regulating device at the inlet tothe actuator or an alternate actuator model may be selectedthat is rated for a higher MOP.4.2.2. Moving to the right along that row, locate the column corresponding to the minimum operating pressure available to theactuator and read the pressure stroke start torque.4.2.3. The pressure stroke start torque at the minimum pressuremust be higher than the valve’s unseating torque requirement.4.2.4. The hydraulic end torque must exceed the valve’s torquerequirement at this stroke end position to open the valve fullyin the CCW direction.flowserve.com9
Limitorque LHS Hydraulic Heavy-Duty Actuator Series FCD LFENTB0003-00-AQ - 11/145. Single Action and Double Action ConfigurationsThe LHS actuator is designed for work in both single acting (fail open and fail close) and double acting configurations:Figure 3: Single Acting Actuator Configuration: Fail Close – Fail ClockwiseFigure 4: Single Acting Actuator Configuration: Fail Open – Fail CounterclockwiseFigure 5: Double Acting Actuator Configuration – Close Position10
Limitorque LHS Hydraulic Heavy-Duty Actuator Series FCD LFENTB0003-00-AQ - 11/14Figure 6: Double Acting Actuator Configuration – Open Position6. Performance Data8. DisclaimerThe following performance data chart provides the following:This publication is presented for information purposes only, with aneffort to ensure the accuracy, the contents are not to be construedas warranties or guarantees, expressed or implied, regarding theproducts or services described herein or their use or applicability.The right to modify or improve the designs or specifications of ourproducts at any time without notice is reserved. Maximum Operating Torque (MOT) Maximum Operating Pressure (MOP) that can be applied to theactuator Maximum allowable working pressure (MAWP) that can beapplied to the static actuator at the stroke end against travel stops Swept Volume required to stroke the actuatorNote: provided performance data may be subject to variationsdue to continuous improvement of LHS products. For latest dataplease contact Flowserve and/or refer to technical documentationtransmitted along with the quotes.7. DimensionsThe following Dimensions & Weight tables include main externaldimensions referred to the relevant pictures included in each section.The overall lengths, the weights, the mounting dimension details, theinterface dimensions and the tolerances are included as a guide foractuator selection.The stated dimensions and weights include the actuators only,without any optional features, like the spool pieces, manualoverrides, control panels, etc.flowserve.com11
Limitorque LHS Hydraulic Heavy-Duty Actuator Series FCD LFENTB0003-00-AQ - 11/14Torque Charts – Single Acting Fail Close – Imperial and MetricTable 1: Torque Table – LHS-15A – Single Acting – Spring Return Fail Close – SymmetricMOT (Maximum Operating Torque): 5500 Nm (4057 ft-lb)MAWP (Maximum Allowable Working Pressure): 207 barg (3000 PSIG)LHS-15A SYMMETRIC ACTUATORActuator startrunendstartrunend207 (3000)MaxOperatingPressurebarg (PSIG)barg (PSIG)barg (PSIG)L3538 (2610)1912 (1410)3269 (2411)4368 (3222)2378 (1754)4099 (3023)5277 (3892)2889 (2131)5008 (3694)3676 (2712)1990 (1468)3407 (2513)4536 (3345)2472 (1824)4266 (3146)5477 (4039)3001 (2213)5207 (3841)207 (3000)0.3207 (3000)0.4207 (3000)0.4177 (2570)0.5133 (1930)0.7104 (1502)0.992 (1340)1.0207 (3000)0.3207 (3000)0.4207 (3000)0.4180 (2618)0.5136 (1968)0.7106 (1532)0.994 (1366)1.0207 (3000)0.3207 (3000)0.4207 (3000)0.4190 (2757)0.5143 (2070)0.7111 (1611)0.999 (1439)1.0207 (3000)0.3207 (3000)0.4207 (3000)0.4202 (2936)0.5152 (2208)0.7119 (1719)0.9106 (1533)1.0207 (3000)0.3207 (3000)0.4207 (3000)0.4206 (2986)0.5155 (2246)0.7120 (1746)0.9107 (1559)1.0Output Torque Nm (ft-lb) @ supply pressureSpringTorque60 (870)70 (1015)80 (1160)Nm (ft-lb)barg (PSIG)barg (PSIG)barg (PSIG)barg (PSIG)barg (PSIG)barg (PSIG)barg (PSIG)barg (PSIG)barg (PSIG)barg (PSIG)619 (457)279 (206)375 (277)619 (457)279 (206)375 (277)619 (457)279 (206)375 (277)619 (457)279 (206)375 (277)619 (457)279 (206)375 (277)619 (457)279 (206)375 (277)619 (457)279 (206)375 (277)759 (560)348 (256)478 (353)759 (560)348 (256)478 (353)759 (560)348 (256)478 (353)759 (560)348 (256)478 (353)759 (560)348 (256)478 (353)759 (560)348 (256)478 (353)759 (560)348 (256)478 (353)1204 (888)553 (408)765 (564)1204 (888)553 (408)765 (564)1204 (888)553 (408)765 (564)1204 (888)553 (408)765 (564)1204 (888)553 (408)765 (564)1204 (888)553 (408)765 (564)1204 (888)553 (408)765 (564)1823 (1344)832 (614)1140 (841)1823 (1344)832 (614)1140 (841)1823 (1344)832 (614)1140 (841)1823 (1344)832 (614)1140 (841)1823 (1344)832 (614)1140 (841)1823 (1344)832 (614)1140 (841)1823 (1344)832 (614)1140 (841)1962 (1447)900 (664)1243 (917)1962 (1447)900 (664)1243 (917)1962 (1447)900 (664)1243 (917)1962 (1447)900 (664)1243 (917)1962 (1447)900 (664)1243 (917)1962 (1447)900 (664)1243 (917)1962 (1447)900 (664)1243 (917)771 (569)357 (264)502 (370)1020 (752)497 (367)751 (554)1293 (954)651 (480)1023 (755)1589 (1172)817 (603)1320 (973)2253 (1662)1190 (878)1984 (1463)3012 (2222)1617 (1192)2743 (2023)3427 (2528)1850 (1364)3158 (2329)657 (485)282 (208)347 (256)906 (668)422 (311)596 (440)1179 (869)575 (424)869 (641)1475 (1088)742 (547)1165 (859)2139 (1578)1115 (822)1829 (1349)2898 (2138)1541 (1137)2588 (1909)3313 (2444)1774 (1309)3003 (2215)969 (715)469 (346)699 (516)1259 (929)632 (466)990 (730)1578 (1164)811 (598)1308 (965)1923 (1419)1005 (741)1654 (1220)2698 (1990)1440 (1062)2429 (1791)3584 (2643)1938 (1429)3314 (2444)4068 (3000)2210 (1630)3798 (2801)855 (630)393 (290)545 (402)1145 (845)556 (410)835 (616)1463 (1079)735 (542)1153 (851)1809 (1334)929 (685)1499 (1106)2584 (1906)1365 (1007)2274 (1677)3470 (2559)1862 (1373)3160 (2330)3954 (2916)2134 (1574)3644 (2687)1759 (1298)913 (673)1490 (1099)2216 (1634)1169 (862)1946 (1436)2716 (2003)1450 (1070)2446 (1804)3259 (2404)1755 (1295)2990 (2205)4477 (3302)2439 (1799)4207 (3103)1957 (1443)1024 (755)1687 (1245)2455 (1811)1304 (961)2185 (1612)3001 (2213)1610 (1187)2731 (2014)3593 (2650)1943 (1433)3324 (2452)4922 (3630)2689 (1983)4652 (3431)2352 (1735)1246 (919)2083 (1536)2933 (2164)1572 (1160)2664 (1965)3570 (2633)1930 (1423)3300 (2434)4262 (3143)2318 (1710)3992 (2944)2748 (2026)1468 (1083)2478 (1828)3412 (2516)1841 (1358)3142 (2317)4139 (3053)2250 (1659)3869 (2854)4930 (3636)2694 (1987)4660 (3437)3143 (2318)1690 (1246)2873 (2119)3890 (2869)2110 (1556)3620 (2670)4708 (3473)2569 (1895)4439 (3274)1448 (1068)726 (536)1138 (839)1863 (1374)959 (708)1553 (1145)2317 (1709)1215 (896)2007 (1480)2811 (2074)1492 (1101)2501 (1845)3918 (2890)2114 (1559)3608 (2661)5183 (3823)2825 (2083)4873 (3594)1645 (1214)837 (618)1335 (985)2102 (1550)1094 (807)1792 (1322)2602 (1919)1375 (1014)2292 (1690)3145 (2320)1680 (1239)2835 (2091)4363 (3218)2364 (1744)4053 (2989)863 (636)348 (257)377 (278)1159 (855)515 (380)674 (497)1823 (1345)888 (655)1338 (987)2582 (1904)1314 (969)2097 (1547)2997 (2211)1547 (1141)2512 (1853)1364 (1006)691 (509)1094 (807)1738 (1282)900 (664)1468 (1083)2147 (1583)1130 (834)1877 (1385)2591 (1911)1380 (1018)2322 (1713)3588 (2646)1940 (1431)3318 (2447)4726 (3486)2579 (1902)4456 (3287)5349 (3945)2929 (2160)5079 (3746)1250 (922)615 (454)940 (693)1624 (1197)825 (609)1314 (969)2033 (1499)1055 (778)1723 (1271)2477 (1827)1305 (962)2167 (1599)3473 (2562)1864 (1375)3163 (2333)4612 (3402)2504 (1847)4302 (3173)5234 (3861)2854 (2105)4924 (3632)934 (689)388 (286)449 (331)1307 (964)598 (441)822 (606)1716 (1266)828 (611)1231 (908)2161 (1594)1078 (795)1676 (1236)3157 (2329)1637 (1208)2672 (1971)4296 (3168)2277 (1679)3810 (2810)4918 (3628)2627 (1937)4433 (3270)1562 (1152)802 (591)1292 (953)1977 (1458)1035 (763)1707 (1259)2431 (1793)1290 (952)2162 (1594)2925 (2158)1568 (1156)2656 (1959)4032 (2974)2190 (1615)3763 (2775)5297 (3907)2900 (2139)5028 (3708)829 (611)329 (243)344 (254)1147 (846)508 (375)662 (488)1493 (1101)703 (518)1008 (743)2268 (1673)1138 (839)1783 (1315)3153 (2326)1635 (1206)2668 (1968)3638 (2683)1907 (1407)3152 (2325)1166 (860)580 (427)897 (661)1498 (1105)766 (565)1229 (906)1862 (1373)970 (716)1593 (1175)2257 (1665)1192 (880)1988 (1466)3143 (2318)1690 (1246)2873 (2119)4155 (3064)2258 (1666)3885 (2866)4708 (3473)2569 (1895)4439 (3274)1052 (776)504 (372)742 (548)1384 (1021)691 (509)1074 (792)1748 (1289)895 (660)1438 (1061)2143 (1581)1117 (824)1833 (1352)3029 (2234)1614 (1191)2719 (2005)4041 (2980)2183 (1610)3731 (2752)4594 (3388)2494 (1839)4284 (3160)736 (543)277 (204)251 (185)1068 (788)464 (342)583 (430)1432 (1056)668 (493)947 (698)1827 (1348)890 (657)1342 (990)2713 (2001)1388 (1023)2227 (1643)3724 (2747)1956 (1443)3239 (2389)4278 (3155)2267 (1672)3793 (2797)1131 (834)499 (368)646 (477)1546 (1141)732 (540)1061 (783)2001 (1476)988 (729)1516 (1118)2495 (1840)1265 (933)2010 (1482)3602 (2657)1887 (1392)3117 (2299)4867 (3590)2598 (1916)4382 (3232)1329 (980)610 (450)844 (622)1786 (1317)867 (639)1300 (959)2286 (1686)1148 (847)1800 (1328)2829 (2087)1453 (1072)2344 (1729)4047 (2985)2137 (1576)3561 (2627)5438 (4011)2919 (2153
2. LHS Hydraulic actuators deliver up to 250 kNm* (184 000 ft-lb) of precisely controlled torque. LHS Limitorque Hydraulic Actuator is enlarging the recent Limitorque Fluid Power Systems family of heavy-duty scotch yoke actuators. The same design philosophy introduced on heavy-duty LPS actuators has been adopted for the LHS range, bringing enhanced
Historical Consumer Marketplace Lending Loan Originations 3,500 500 0 Q1-14 Q3-14 Lending Club (LHS) Sofi (LHS) Prosper (LHS) Marlette (LHS) Avant (LHS) Upstart (LHS) Upgrade (LHS) Freedom F (LHS) LendingPoint (LHS) All (RHS) Millions 2,000 1,500 1,000 9 7 0 Billions 3 2 1 2,500 3,000 5 4 6 8
Note: The LHS’s generated by JMP are actually maximin LHS’s. By this, I mean that from among all possible LHS’s, JMP picks the one that is maximin. By so doing, JMP eliminates “poor” LHS’s and guarantees that it generates an LHS that spreads points out reasonably evenly.
ROD SEALS PISTON SEALS ROD WIPERS UBR/ZBR Seal Locking Capped T-Seal SH Wiper HEAVY DUTY MOBILE HYDRAULIC HEAVY DUTY MOBILE HYDRAULIC HEAVY DUTY MOBILE HYDRAULIC Unsymmetrical U-CUP Capped T-Seal MC Wiper MOBILE HYDRAULIC AGRICULTURAL GENERAL INDUSTRIAL HEAVY D
Pneumatic Actuator Electric Actuator Hydraulic Actuator Gas – hydraulic Actuator Electric – hydraulic Actuator Carbon steel, stainless steel, alloy,Duplex SS Body: NEWAY reserves the right to change design, materials or specifications without notice and is free of obligation to fur
HYDRAULIC BOTTLE JACKS 1 HYDRAULIC BOTTLE JACKS K12150 - 1850kg Hydraulic Bottle Jack K12151 - 4000kg Hydraulic Bottle Jack K12152 - 6000kg Hydraulic Bottle Jack K12153 - 10000kg Hydraulic Bottle Jack K12157 - 20000kg Hydraulic Bottle Jack K12158 - 10000kg Hydraulic Bottle Jack K12159 - 20000kg Hydraulic Bottle Jack ED1 / JUNE 19 Distributed by Kincrome Tools and Equipment www.kincrome.com.au
Paladon Systems Self-Contained Electro-Hydraulic Control Systems are integrally mounted to the actuator, and typically consist of the following basic system components: Non-Pressurized Hydraulic Reservoir Electric Pump/s Hydraulic Accumulator/s Electro-Hydraulic Control System Hydraulic Valve Actuator/s SYSTEM OVERVIEW www.paladonsystems.com
Hydraulic MotorS Medium Duty Series Delivering The Power To Get Work Done Hydraulic motors ld md Hd Hydraulic motor brake units steering units Hydraulic brakes Hydraulic pumps Flow dividers. DELIVERING THE POWER TO GET WORK DONE 3 table of contents technical information
PERFORM SOME BALLET THEMES: Choose from the three themes on the Tchaikovsky Ballet Music sheet and perform on an instrument of your choice. Add in the left hand chords if you are playing on keyboard or piano. You could play either: Theme from the Dance of the Sugar Plum Fairies The Waltz from Sleeping Beauty The March from the .
