INSTALLATION INSTRUCTIONS JAZZ - Genuine Honda

INSTALLATIONINSTRUCTIONSDOOR VISORSJAN. 2011JAZZINDEXParts List . 1Tools and Supplies Required . 2Before You Begin Customer Information . 2Illustration of the Door Visors on the Vehicle . 2Installation Installing the Rear Door Visor. 3 Installing the Front Door Visor . 12Confirmation After Installation Restoration operations. 16Use and Care. 16Parts ListLeft front door visorRight front door visorLeft rear door visorRight rear door visorBrackets F (2)Brackets G (8)Brackets H (2)Clips (12)EPT sealerSealers (6) Honda Access Corp. 201108R04-TF0-6A00-901 / 16

Tools and Supplies Required Shop towel Scale Masking tape Contact cleanerBefore You BeginCustomer Information These installation instructions show the left door visors being installed. The same procedure applies to installing theright door visors. Do not damage the paint finish and run channels when installing the door visors. Handle the door visors with care. They are not designed to absorb shock or impact. Clean the surface thoroughly where the tape, etc. will attach using a shop towel dampened with the contact cleaner.Let the cleaned surface dry thoroughly before installation. This door visor kit should be installed only if the ambient air temperature is 15 C (60 F) or above. Install the part or double-sided adhesive tape properly at first try. Your attempt to detach the part or double-sidedadhesive tape to correct the position can damage the part or deteriorate the bonding performance of the double-sidedadhesive tape. To allow the adhesive to cure, do not wash the vehicle for 24 hours.Illustration of the Door Visors on the VehicleRIGHT REARDOOR VISORRIGHT FRONTDOOR VISORLEFT REARDOOR VISORLEFT FRONTDOOR VISOR082501AJ2 / 1608R04-TF0-6A00-90

InstallationRUN CHANNELInstalling the Rear Door Visor1.2.Fully open the left rear door glass.Release the front side of the run channel.LEFT REAR DOOR831101AH3.4.5.Open the run channel as shown, and measureits dimensions.Using contact cleaner, clean the position wherethe EPT sealer (long) will attach.Remove the EPT sealer (long) from theadhesive backing, and attach it as shown. Check that the EPT sealer (long) isattached properly.EPT SEALER (long)JOIN50 mm(2.0 in.)RUNCHANNELJOINPosition wheresealer isattachedClean with thecontact cleaner.EPT SEALER(long)FRONTFRONT Correct 7 mm(0.3 in.) Incorrect OUTSIDEOUTSIDE SECTION VIEW 861820AH08R04-TF0-6A00-903 / 16

6.Reinstall the run channel. Check that the run channel is installedsecurely.RUN CHANNEL SECTION VIEW Correct Incorrect Check the run channelis installed securely.831103BH7.8.Release the two retaining tabs, and slide the leftrear quarter garnish out of its position. Take care when sliding the left rear quartergarnish carefully it is easily damaged.Release the rear side of the run channel.RUN CHANNEL2 RETAININGTABSLEFT REAR QUARTERGARNISH4 / 1608R04-TF0-6A00-90LEFT REAR DOOR831104AH

9. Open the run channel as shown.10. Using contact cleaner, clean the position wherethe EPT sealer (short) will attach.11. Remove the EPT sealer (short) from theadhesive backing, and attach it as shown. Check that the EPT sealer (short) isattached properly.EPT SEALER (short)RUN CHANNELGroove at thevery bottomRUN CHANNELPosition wheresealer isattachedClean with thecontact cleaner.EPT SEALER(short)REARREAR Correct Incorrect OUTSIDEOUTSIDE7 mm(0.3 in.) SECTION VIEW 861821AH08R04-TF0-6A00-905 / 16

12. Reinstall the run channel and left rear quartergarnish. Check that the run channel is installedsecurely.RUN CHANNEL SECTION VIEW Correct Check the run channelis installed securely.6 / 1608R04-TF0-6A00-90 Incorrect 831203BH

13. Release the run channel as shown.14. Install two brackets G to the door sash asshown.15. Reinstall the run channel. Check that the run channel is installedsecurely. Check that the brackets G are installedsecurely on the door sash as shown.DOORSASH FRONT VIEW FRONT VIEW 60 mm (2.4 in.)60 mm (2.4 in.)BRACKET GBRACKET G2 BRACKETS GRUN CHANNELDOOR SASH Correct RUN CHANNELDOOR SASH Incorrect RUN CHANNEL SECTION VIEW BRACKET G16. Using contact cleaner, clean the door sashwhere the left rear door visor will attach.BRACKET G040502AJClean withcontact cleaner.040503AJ08R04-TF0-6A00-907 / 16

17. Remove the adhesive backing from eachsealer, and attach them to the left rear door asshown.7 mm(0.3 in.)Align.DOORGARNISHSEALERDOOR GARNISHAlign.FRONT5 mm(0.2 in.)SEALER040504BJ18. Attach the masking tape to an end of theadhesive backing of the left rear door visor. Peelback the adhesive backing partway and attachit to the surface side of the left rear door visor.19. Remove two adhesive backings.LEFT REARDOOR VISORFRONTMASKINGTAPE2 ADHESIVEBACKINGSRemove.8 / 1608R04-TF0-6A00-90ADHESIVEBACKINGPeel back.040505AJ

20. Secure the left rear door visor to two brackets Gwith two clips. Be extremely careful when installing theclip. Clip can not be removed andreinstalled after installation.LEFT REARDOOR VISORBRACKET GBRACKET G2 CLIPS040506AJ21. Push the left rear door visor that you justinstalled on the door sash upward, and checkthat it aligns with the contour of the door sash. Push the brackets firmly against the doorsash so there is no gap between them. SECTION VIEW DOOR SASHBRACKET GPush.LEFT REARDOOR VISORDOOR SASH040507AJ08R04-TF0-6A00-909 / 16

22. Insert the bracket H between the rear pillargarnish and the door sash, and secure the leftrear door visor to the bracket H with the clip. Be extremely careful when installing theclip. Clip can not be removed andreinstalled after installation. SECTION VIEW BRACKET HDOOR SASHBRACKET HREAR PILLARGARNISHLEFT REARDOOR VISORCLIP040508AJ10 / 1608R04-TF0-6A00-90

23. While removing the adhesive backing thattemporarily attached to the surface side of theleft rear door visor, press the left rear door visorfirmly from the front side toward the rear. Remove the adhesive backing whilepressing the left rear door visor in thedirection of the arrow with your fingers sothere is no gap between the brackets andthe door sash.24. Secure the left rear door visor by pressing it atthe ends for 30 seconds.Align.LEFT REARDOOR VISORADHESIVEBACKINGRemove.Pressfirmly.BRACKETS GPush.040509AJ08R04-TF0-6A00-9011 / 16

Installing the Front Door Visor FRONT VIEW 25. Fully open the left front door glass.26. Release the run channel as shown.27. Install two brackets G to the door sash asshown.28. Reinstall the run channel. Check that the run channel is installedsecurely. Check that the brackets G are installedsecurely on the door sash as shown.60 mm(2.4 in.) FRONT VIEW 60 mm(2.4 in.)BRACKET GBRACKET GRUN CHANNEL2 BRACKETS GLEFTFRONTDOOR Correct RUN CHANNELBRACKET G Incorrect RUN CHANNEL SECTION VIEW BRACKET G040510AJ29. Install the bracket F between the door sash andthe run channel in the position shown. SECTION VIEW BRACKET FDOOR SASHRUN CHANNEL761015AS12 / 1608R04-TF0-6A00-90

30. Using contact cleaner, clean the door sashwhere the left front door visor will attach.Clean withcontact cleaner.040511AJ31. Remove the adhesive backing from the sealer,and attach it to the left front door as shown.Align.3 mm (0.1 in.)DOORGARNISHSEALERFRONT040512BJ32. Attach the masking tape to an end of theadhesive backing of the left front door visor.Peel back the adhesive backing partway andattach it to the surface side of the left front doorvisor.33. Remove two adhesive backings.2 ADHESIVEBACKINGSRemove.ADHESIVEBACKINGPeel back.FRONTMASKINGTAPELEFT FRONTDOOR VISOR040513AJ08R04-TF0-6A00-9013 / 16

34. Secure the left front door visor to two bracketsG with two clips. Be extremely careful when installing theclip. Clip can not be removed andreinstalled after installation.LEFT FRONTDOOR VISORBRACKET GBRACKET G2 CLIPS040514AJ35. Push the left front door visor that you justinstalled on the door sash upward, and checkthat it aligns with the contour of the doorgarnish. Push the brackets firmly against the doorsash so there is no gap between them.Align. SECTION VIEW DOORSASHPush.BRACKET GDOORGARNISHLEFT FRONTDOOR VISOREqual.LEFT REARDOOR VISORLEFT FRONTDOOR VISOR14 / 1608R04-TF0-6A00-90Align.040515AJ

36. Set the bracket F in the correct position bymoving it up or down so the clip installation holein the bracket F aligns with the clip installationhole in the left front door visor.37. Secure the left front door visor to the bracket Fwith the clip. Be extremely careful when installing theclip. Clip can not be removed andreinstalled after installation.LEFT FRONTDOOR VISORCLIPBRACKET FCLIP SECTION VIEW 040516AJ38. While removing the adhesive backing thattemporarily attached to the surface side of theleft front door visor, press the left front doorvisor firmly from the rear side toward the front. Remove the adhesive backing whilepressing the left front door visor in thedirection of the arrow with your fingers sothere is no gap between the brackets andthe door sash.39. Secure the left front door visor by pressing it atthe ends for 30 seconds.40. Repeat steps 1 through 39 on the right side ofthe vehicle.ADHESIVEBACKINGRemove.Press firmly.LEFT FRONTDOOR VISORBRACKETS GPush.040517AJ08R04-TF0-6A00-9015 / 16

Confirmation After InstallationRestoration operations1.2.3.4.5. Start the engine.Using the power window switch, fully open the window, and check that there is no fault such as pinched runchannel, etc.Using the power window switch, repeat opening and closing of the window from half-open to fully closed 4 or 5times to allow the run channel to wear in. (Practice this operation while checking absence of a failure such aspinched run channel, etc.)Referring to the service manual of the vehicle, reset the power window. (If the automatic closing/opening does notfunction after the reset, reset again.)Referring to the service manual of the vehicle, carry out “learning” of the power window. (If the automatic closing/opening does not function after the learning, carry out “learning” again.)The operations in the steps 4 & 5 should be applied to all power windows having the automatic closing/openingfunction to allow for proper functioning of the anti-pinching function after installing the door visor.Use and Care When the door visor is dirty, clean it with a soft cloth dampened with water. When the door visor is very dirty, clean the door visor with the neutral detergent and water. Do not use volatile solvent(e.g. thinner, benzine, alcohol, etc.) or a cleaner containing abrasive material.16 / 1608R04-TF0-6A00-90

the EPT sealer (short) will attach. 11. Remove the EPT sealer (short) from the adhesive backing, and attach it as shown. † Check that the EPT sealer (short) is attached properly. 861821AH OUTSIDE EPT SEALER (short) SECTION VIEW EPT SEALER (short) Groove at the very bottom RUN CHANNEL REAR 7 mm (0.3 in.) REAR Position where sealer is .