Q7055C1034, Q7055C1035 Fire Network Adapters (FNA3)
Q7055C1034, Q7055C1035Fire Network Adapters (FNA3)INSTALLATION INSTRUCTIONSGENERALThe Q7055C1035 and Q7055C1034 Fire Network Adapters(FNA3) provide a UL 864-9th edition listed interface betweenthe Honeywell XLS140 and XLS3000 fire alarm systems andHoneywell Enterprise Buildings Integrator (EBI) servers andworkstations via a Local Area Network (LAN). They allowseamless fire alarm point display, command, and control viathe EBI. The FNA3 supports two types of connections to theXLS140 and XLS3000 fire alarm systems. A single XLS140/3000 fire alarm control panel can be directly connected to anFNA3 to interface it with EBI via a LAN. Multiple (up to 100)XLS140/3000 panels (including XLS NCA devices) networkedvia XLS-NET can connect to an FNA3 via a NetworkCommunication Module (NCM), so as to interface with the EBIvia the LAN.Temperature Ratings:Operating: 32 to 120 F (0 to 49 C).Storage: -31 to 160 F (-35 to 70 C).Humidity Ratings: 5 to 93% RH, non-condensing.System Data:Processor: 32 bit high speed microprocessor.Data Transfers: 10/100 Mbit/sec., 802.3 Ethernet.LAN Interfaces: 10/100BaseT (RJ-45).Field Bus and Device Interface: Serial EIA/RS-232.Memory Type: SDRAM, NOR & NAND flash.MTBF: 100,000h.Safety:Protection Standard: IP20 acc. to EN60529.Protection Class: II acc. to EN60730-1.Flame Retardant: V0 acc. to UL 94.24 Vdc power for the Q7055C1035 can be provided from anauxiliary output of the XLS140 or XLS3000 fire alarm controlpanel. An optional 120/240 Vac input power supply is alsoavailable for stand-alone applications. The Q7055C1035mounts directly on a 14006090-555151 seriescommunications panel using the FNA3 mounting ears(mounting ears are included with the Q7055C1035). TheQ7055C1034 mounts inside an XLS140 or XLS3000 paneland uses the panel's power supply.Dimensions (W x H x D):FNA3: 8-13/16 in. (224 mm) x 2-13/16 in. (72 mm) x 7-13/16in. (199 mm).FNA3-XLS: 19 in. (483 mm) x 8 in. (203 mm) x2 1/8 in. (54 mm)Status information, like LAN communication activity, field bustraffic communication and system Heartbeat of the FNA3 isindicated by LEDs on the device front.Approvals:Electromagnetic Compatibility (EMC):EN50081-1, EN50082-2, and EN50130-4.Electromagnetic Emission (EME): FCC Class A.Control Units and Accessories for Fire Alarm Systems (UL864-9th), Energy mgt. (UL 916), Proprietary Burglar AlarmUnits and Systems (UL 1076), Central Station BurglarAlarm Units and Systems (UL1610), General Purpose. Sig.(UL 2017).Fire Alarm: (ULC-S527-99); requirements of Canadian province and local building codes; CEC 22.1 Canadian Electrical Code; ULC S559-04, Equipment for Fire SignalReceiving Centres and Systems.Mass Notification Systems (UL 2572).Ground fault detection is provided by the Honeywell GFDground fault detection module. Refer to Fig. 10.SPECIFICATIONSModel:Q7055C1035 Fire Network Adapter (FNA3).Q7055C1034 Fire Network Adapter (FNA3-XLS).Electrical Ratings:Supply Voltage: 24 Vac, 50 to 60 Hz, 24 Vdc (external powersupply required).NOTE: The power supply must be regulated, power limited and listed for use in fire alarm systems.Power Consumption: 8 VA.XLS FACP power supply/standby battery load: 24 Vdc @ 300mA.Weight:FNA3: 2.0 lb (0.9 kg)FNA3-XLS: 4.3 lb. (2.0 kg)Additional Equipment:DC Power supply: 50017367-001 - Jameco Model No.DDU240050, 120 Vac, 60 Hz input, 24 Vdc, 0.500 A output,wall mounted power cube 15 VA Class 2 (Ever Glow, ULFile number E135456).DC Power supply: CUI Model No. EMS240075-P5P-SZ 120/240 Vac, 50/60 Hz input, 24 Vdc, 0.75 A output, Class 2.Put Bar Code Here95 8524 4
Q7055C1034, Q7055C1035 FIRE NETWORK ADAPTERS (FNA3)requirements. This connector can also beused to configure the device by following aHyperTerminal connection procedureduring device boot-up.DC Power supply: CUI Model No. SMI18-24-V-P5, 120/ 240Vac, 50/60 Hz input, 24 Vdc, 0.8 A output, Class 2.AC Power Supply: 120 Vac, 50/60 Hz 24 VA input, 24 Vac output, Honeywell 14507287 series or 14507350-002 listed.75554 NUP-DB9 Data Cable (Included).75583 NCM Power Cable.NCM-W Network Communications Module - wire typeNCM-F Network Communications Module - fiber typeHS-NCM-W Network Communications Module - wire typeHS-NCM-F Network Communications Module - fiber typeXLS-NCM-EBI-F PC Mounted NCM device- fiber type (contains 75557 RS-232 NCS-NCW cable).XLS-NCM-EBI-W PC mounted NCM device- wire type (contains 75557 RS-232 NCS-NCW cable).XLS-HS-NCM-EBI-F PC mounted NCM device- fiber type(contains 75557 RS-232 NCS-NCW cable).Power:3-pole Phoenix power connector for24 Vac/dc power supplies.10/100BASE TPOWERFNA3SYSTEM OVERVIEWFIELD BUS CONNECTION1Fig. 1 shows an application example of the FNA3 device in aBuilding Management System.1THE FIELD BUS CONNECTION IS AS FOLLOWS:FNA3, ONE EIA/RS232 COMPATIBLE BUS.M30006Fig. 2. FNA3 Components.EBIUL LISTED WORKSTATIONBEFORE INSTALLATIONUL LISTED WORKSTATIONPerform the following steps prior to installing the FNA device:XLSNCM-EBI1.NUPDB9CABLE2.3.ETHERNET LAN——GFDRS-232FNA3FNA3XLS-NET WITH UPTO 100 XLS-NETTYPE DEVICESTO NUP CONNECTOR ON:1) A STANDALONE XLS140OR XLS3000 PANEL2) A DEDICATED NCM FORCONNECTION TO XLS-NETWITH UP TO 100XLS-NET TYPE DEVICES————M300054.Fig. 1. Application Block Diagram.Typical characteristics of the FNA3 components are as follows(See Fig. 2):FNA3:FNA3 INSTALLATION WITH XLSNETThe FNA3 contains a high-speed state-ofthe-art 32-bit microprocessor including acommunication coprocessor designed formaximum performance. It is designed forreliable and robust operation under a widerange of operating conditions.The FNA3 will use an EIA/RS-232 cable to connect eitherdirectly to an XLS panel CPU, or to an XLS-NET NCM locatedin an XLS panel, or to an XLS-NCM-EBI device mounted inthe EBI computer.When the FNA3 is located next to a standalone XLS CPU, itcan use the DB9-NUP connector cable P/N 75554 to connectdirectly to the XLS PANEL NUP network service connectionon the CPU.10/100BaseT: 10/100Base RJ-45 Ethernet LANconnector meets the requirements ofANSI/TIA/EIA 586 Category 5 forunshielded twisted pair connections.Field Bus:95-8524-4Verify that the product has been received without damage.Verify that the correct FNA device has been delivered.Check the package contents. The following items areincluded in each product package:Fire Network Adapter device.50017367-001 or CUI Model No. EMS240075-P5P-SZPower SupplyorSMI18-24-V-P5 Power Supply.Ground wire with lug.75554 NUP-DB9 Data cable.Fire Network Adapter Installation Instructions.Bag of installation materials as follows: one 3-polePhoenix power connector, and mounting hardware.Study the wiring diagrams carefully prior to connectingpower, ground, and data interface cables to the FNA.When the FNA3 needs to be connected with a networked XLSCPU (or another networked XLS device) it requires its ownNCM and the 75583 power cable. In this case, the NCM9-pin SUB-D EIA/RS-232 connector forXLS-NET field bus connection electricallyisolated, meets the EMC and FCC2
Q7055C1034, Q7055C1035 FIRE NETWORK ADAPTERS (FNA3)computer. The XLS-NET can be wired directly to theXLS-NCM-EBI via an edge-mounted connector. The FNA3can be connected to the EIA/RS-232 port on the XLS-NCMEBI with cable P/N 75557 (supplied with XLS-NCM-EBI).device is powered via the 75583 cable, and connects to theXLS-NET. The FNA3 uses the 75554 DB9-NUP cable toconnect to the NUP connector on the NCM device.A hub or a switch between FNA3 and EBI computer LAN portsis required only if additional network devices are to beconnected.If the FNA3 is located in the same room as the EBI, then GFDand Ethernet port surge protection devices are not requiredfor monitoring and protecting the Ethernet cables betweenFNA3 and EBI computer.IMPORTANT— The DB-9 NUP EIA/RS-232 Field Bus cable must notexceed 20 ft (6.1 m) in length, and must be installedin conduit.— The FNA3 and XLS PANEL or NCM must be locatedwithin the same room.When the FNA3 is in the same room with EBI computer butnot with the XLS CPU, it can be connected to XLS-NET withthe use of an XLS-NCM-EBI device installed inside the EBISLC NO. 19111TC809A1059TC810N1013TC810R1024CONTROL MONITORXLS PANELTODETECTORS&MODULESRELAY11SLC NO. ION2NUPConnector14FNA3NUP EIA-232 DB9ETHERNETRJ-45Communication cabinetXLS CabinetXLS-NET(OPTIONAL)1275554 DATA CABLE. CONNECTED INCONDUIT AND IN THE SAME ROOM.THE STANDARD CABLE IS 10 FT. (3M) LONG,BUT IT MAY BE EXTENDED TO20 FT. (6M) MAXIMUM.CONNECT TO NETWORK SERVICECONNECTION (NUP) ON XLS CPU OR NCM.3USE GFD DEVICES WITH ANY ETHERNETCABLES THAT EXCEED 20 FT. (6 M).4USE 14807678-004 DITEK ETHERNET PORT SURGEPROTECTOR IF ETHERNET LEAVES THE ROOM.5A HUB OR A SWITCH BETWEEN FNA3 ANDEBI COMPUTER LAN PORTS IS REQUIRED ONLYIF ADDITIONAL NETWORK DEVICES ARE TO BECONNECTED.3ETHERNETRJ-454ETHERNETHUB/SWITCH5EBI WORKSTATIONM30008Fig. 3. Typical External Q7055C1035/XLS Panel Connect Block Diagram.395-8524-4
Q7055C1034, Q7055C1035 FIRE NETWORK ADAPTERS (FNA3)Table 1. Field Bus 9 Pin Sub D Bus Connector Terminal cyMax. LineImpedanceField Bus 9Pin Sub D3RXDInput/OutputSIGNAL 12 V 12 mA115.2 k baud100 ohmsField Bus 9Pin Sub D5TXDInput/OutputSIGNAL 12 V 12 mA115.2 k baud100 ohmsField Bus 9Pin Sub ax. wiring distance 20 ft. (6.1 m.), 24 AWG minSLC NO. 1TO NETWORK SERVICECONNECTION (NUP) ONXLS CPU11TC810R1024CONTROL MONITOR11SLC NO. TOIONRJ-45Q7055C1034 FNA3TO XLS POWERSUPPLY, SEE FIG. 77XLS Cabinet123575554 DATA CABLE. CONNECTED INCONDUIT AND IN THE SAME ROOM.THE STANDARD CABLE IS 10 FT. (3M) LONG,BUT IT MAY BE EXTENDED TO20 FT. (6M) MAXIMUM.CONNECT TO NETWORK SERVICECONNECTION (NUP) ON XLS CPU.USE GFD DEVICES WITH ANY ETHERNETCABLES THAT EXCEED 20 FT. (6 M).3ETHERNETRJ-456EBI WORKSTATION4USE 14807678-004 DITEK ETHERNET PORT SURGEPROTECTOR IF ETHERNET LEAVES THE ROOM.5 A HUB OR A SWTICH BETWEEN FNA3 ANDEBI COMPUTER LAN PORTS IS REQUIRED ONLYIF ADDITIONAL NETWORK DEVICES ARE TO BECONNECTED.6 ETHERNET HUB CAN BE REPLACED WITH ANETHERNET CABLE IF EBI ANDFNA DEVICE ARE IN THE SAME ROOM.7ETHERNETHUB/SWITCH4M30009THE Q7055C1034 FNA3-XLS CAN ONLY BE POWEREDFROM AN XLS FACP POWER SUPPLY. IT REQUIRES300 mA @ 24 Vdc OF POWER SUPPLY AND STANDBYBATTERY CAPACITY. REFER TO POWER SUPPLY ANDBATTERY SIZING INFORMATION IN XLS FACP INSTALLATIONINSTRUCTIONS 95-7673, 95-7731, OR 95-7702.Fig. 4. Typical Internal Q7055C1034/XLS Panel Connect Block Diagram for standalone panels.95-8524-44
Q7055C1034, Q7055C1035 FIRE NETWORK ADAPTERS (FNA3)Table 2. LAN Connector Terminal Current 100 mA1TD OutputSIG 5 V2TD-OutputSIG3RD Input4Not Used5Not Used6RD-Input7Not used8Not Used100 ohms 5 V100 Mbps100 ohmsSIG 5 V100 Mbps100 ohmsSIG 5 V100 Mbps100 ohms 100 mA9111TC810R1024CONTROL MONITOR2DB-9RJ-45TODETECTORS&MODULESRELAY11SLC NO. 2NUPTODETECTORS&MODULES51TC809A1059TC810N1013TO XLS NET1MaximumImpedance100 MbpsSLC NO. NQ7055C1034 FNA3TO XLS POWERSUPPLY.TO XLS POWERSUPPLY SEE FIG. 77Communication cabinetXLS Cabinet175554 DATA CABLE.2CONNECT TO NETWORK SERVICECONNECTION (NUP) ON NCM.3USE GFD DEVICES WITH ANY ETHERNETCABLES THAT EXCEED 20 FT. (6 M).4USE 14807678-004 DITEK ETHERNET PORT SURGEPROTECTOR IF ETHERNET LEAVES THE ROOM.5A HUB OR A SWITCH BETWEEN FNA3 ANDEBI COMPUTER LAN PORTS IS REQUIRED ONLYIF ADDITIONAL NETWORK DEVICES ARE TO BECONNECTED.ETHERNET HUB CAN BE REPLACED WITH ANETHERNET CABLE IF EBI ANDFNA DEVICE ARE IN THE SAME ROOM.675ETHERNETRJ-45ETHERNETHUB346EBI WORKSTATIONM30010THE Q7055C1034 FNA3-XLS CAN ONLY BE POWEREDFROM AN XLS FACP POWER SUPPLY. IT REQUIRES300 mA @ 24 Vdc OF POWER SUPPLY AND STANDBYBATTERY CAPACITY. REFER TO POWER SUPPLY ANDBATTERY SIZING INFORMATION IN XLS FACP INSTALLATIONINSTRUCTIONS 95-7673, 95-7731, OR 95-7702.Fig. 5. Typical Internal Q7055C1034/XLS Panel Connect Block Diagram for panels connected to XLS-NET.595-8524-4
Q7055C1034, Q7055C1035 FIRE NETWORK ADAPTERS (FNA3)Q7055C1034 MOUNTINGby terminating it on a Q7055C1034 mounting stud. Be sure toremove any paint from around the stud to insure a goodconnection. Two nuts and washers are provided in the bag kitfor mounting the Q7055C1034 on the XLS cabinet studs. Thesame stud used for terminating the LAN transient protector’sground wire should also be used to provide a chassisconnection for the green ground wire from the FNA3 powerconnector. The Q7055C1034 FNA3-XLS must be powereddirectly from an internal XLS FACP power supply. Externalpower supplies, such as those recommended for theQ7055C1035 FNA, cannot be used.Typical Q7055C1034 FNA3-XLS mounting in an XLS cabinetis shown in figure 6. Mounting locations and restrictions arethe same as those for the CHS-4L chassis. The space in themiddle of the assembly is used for the FNA3 PWB assembly.Space is available on the left side of the Q7055C1034 formounting an NCM if needed (not included – order separately).The 14507678-004 Ditek LAN transient protector (when it isrequired), can be installed on one of the Q7055C1034mounting studs on the upper right of the FNA3. The transientprotector’s green ground wire should be connected to chassisFig. 6. Typical Q7055C1034 FNA3-XLS mounting in an XLS cabinet.95-8524-46
Q7055C1034, Q7055C1035 FIRE NETWORK ADAPTERS (FNA3)AC/DC IN24VTO 24 Vdc FROM XLSPANEL POWER SUPPLYORA LISTED 24 Vdc OR24 Vac STAND ALONEPOWER SUPPLYCHASSIS GROUND CONNECTION.SECURE LY FASTEN TOCHASSIS GROUND STUD ORUNPAINTED XLS SUB PANELMOUTING BOLT USINGGROUND WIRE ASSEMBLYPROVIDED WITH THEPOWER CONNECTORM30014Fig. 7. Typical power connections for all Q7055C FNA3 models.SLC NO. 1TC810N1013XLSNETWORKCONTROLANNUNCIATORXLS ROL MONITORRELAYSLC NO. 2 DB9FNA3XLS-NETETHERNETRJ-4514006090-555151 SERIESCOMMUNICATION PANEL2XLS CABINETXLS-NCM-EBI1275557 DATA CABLE. CONNECTED INCONDUIT AND IN THE SAME ROOM.THE STANDARD CABLE IS 1.0 FT. (0.3M) LONG,BUT IT MAY BE EXTENDED TO20 FT. (6M) MAXIMUM.CONNECT TO NETWORK SERVICECONNECTION (NUP).ETHERNETRJ-45EBI WORKSTATION3USE 14807678-004 DITEK ETHERNET PORT SURGE PROTECTOR IF ETHERNETLEAVES THE ROOM.4A HUB OR A SWITCH BETWEEN FNA3 ANDEBI COMPUTER LAN PORTS IS REQUIRED ONLYIF ADDITIONAL NETWORK DEVICES ARE TO BECONNECTED.43ETHERNETHUBM25510Fig. 8. Typical FNA3/XLS-NCM-EBI Connect Application Block Diagram.795-8524-4
Q7055C1034, Q7055C1035 FIRE NETWORK ADAPTERS (FNA3)WIRE PER NEC FOR FIRE ALARMH2N GTRIPP-LITE5635Q7055C1035FIRE NETWORKADAPTER (FNA3)3NON-POWERLIMITED AREA4POWER LIMITED AREA1TYPICAL MOUNTING LOCATION FOR Q7055C1035 FIRE NETWORK ADAPTER (FNA2).2G GROUNDING CONDUCTOR31GROUND CONNECTION. 8-32 STUD WITH 8-32 KEPS NUT.4GROUND CONNECTION FOR 14507678-004 DITEK ETHERNET PROTECTOR AND OTHERLOW VOLTAGE EQUIPMENT.5DRILLED MOUNTING HOLES FOR 14507719-001 8 PORT ETHERNET HUB (IF USED).614503899-002 MOV FACTORY INSTALLED ON TERMINAL STRIP.NOTE: SYSTEM WIRING IS CLASSIFIED AS EITHER POWER LIMITED OR NON-POWER LIMITEDPER NEC ARTICLE 760. ALL POWER LIMITED WIRING MUST BE SEPARATED FROM ALLNON-POWER LIMITED WIRING BY A MINIMUM DISTANCE OF 1/4 IN. (6 MM).M30012Fig. 9. Typical Mounting of Q7055C1035 FNA3 on 14006090-555151 Communications Panel.95-8524-48
Q7055C1034, Q7055C1035 FIRE NETWORK ADAPTERS (FNA3)FROM FNA3TO ETHERNET LANRJ-45 CONNECTORPAIR ONE INPAIR TWO INRJ-45 CONNECTOR 121 2 3663PAIR ONE OUTPAIR TWO OUTGROUND FAULT DETECTION MODULE, 2-GANG MOUNT SPECIFICATIONSNOTES:ALL CIRCUITS ARE POWER-LIMITED .CONTACTS 1 AND 7 ARE NO T USED.161413INOUTCIRCUIT PAIR 1FUNCTIONALITY OF THE TROUBLE/GFCIRCUIT IS DEPENDENTON THE JP1POSITION.153-2-1JP1LED111109INOUTCIRCUIT PAIR 2LED2TROUBLE/GF CONTACTSEARTHGND812POWER76NC COM435NO2TO EARTH GROUNDPOLARITY IS NOT IMPORTANT1ELECTRICAL RATINGS: POWER CONSUMPTION IS 50 mA AT 24V. POWER ISISOLATED FROM MONITORED CIRCUITS.MONITORED CIRCUIT(S): CONFIGURATION: MONITORED CIRCUIT(S) MUSTHAVE BOTH CONDUCTORS BALANCED WITH RESPECT TO GROUND.MAXIMUM VOLTAGE: 100 VDC.MAXIMUM CURRENT; 4A.MAXIMUM VOLTAGE BETWEEN MONITORED CIRCUITS: 1000 VDC.CONTACT RATING: 1A AT 30 VDC.TEMPERATURE RATINGS: 32 F TO 120 F (O C TO 49 C).HUMIDITY RATINGS: 93% RH, NON-CONDENSING.WIRING TERMINATIONS: AL L WIRING TO TERMINALS ACCEP T 12 AWG TO 18 AWG(3.3 SQ MM TO 0.82 SQ MM) CONDUCTORS.GROUND FAULT CONDITION: LESS THAN 10K OHMS BETWEEN AN Y MONITOREDCONDUCTOR AND THE REFERENCE GROUND .MOUNTING: COMPATIBLE ELECTRICAL BOXES:NORTH AMERICAN 2-1/2 IN. (64 MM) DEE P, 2-GANG BOX.STANDARD 4 IN. (102 MM) SQUARE BOX, 1-1/2 IN. (38 MM) DEEP BOX.EUROPEAN 3.9 IN. (100 MM) SQUARE BOX.MOUNTING BRACKETS: SIGA-MP1, SIGA-MP2(L).TO SUPERVISORY POINT SUCH AS SIGN ATURESERIES CT1 OR CT2 MODULE, 3-IDCTRADITIONAL ZONE CARD, FS90 AA ,OR TC809, XLS140, XLS3000, OR EQUAL.FROM 24 VDC ON FIREALARM PANEL, ORLISTED SOURCEM30013Fig. 10. Typical GFD Wiring.VOIP COMMUNICATIONSFIELD WIRINGVoice over Internet Protocol (VoIP) is a packet switchedcommunication platform. Use of VoIP communications mayonly be used for general paging. It is not intended for use forany fire alarm or emergency CORECE CERTIFICATIONREQUIREMENTS (EUROPEONLY)TO FNAM23029Fig. 11. CE Certification Wiring.MAINTENANCE PROCEDURESCE compliance requires very low levels of radiated andconductive emissions. Therefore, CE certification requiresadditional emission suppression. All RS-232 field wiringentering the Q7055C1035 FNA3 must be routed through aferrite suppression core as listed in the Specifications Section,under Additional Equipment.The system must be maintained in accordance with thesystem documentation and procedures and practicescontained in applicable NFPA and UL standards. The Q7055CFNA3 has no user replaceable fuses. For service, contactyour local Honeywell Automation & Control Solutions office aslisted in the phone book, or contact a regional office as shownat the end of the document.Ferrite Suppression Core (For AllRS-232 Field Wiring)For each RS-232 field connection terminating in the FNA3,loop both conductors and shield them once through a ferritesuppression core (See Fig. 11). Looping is not required if thefield cable diameter is too large to loop. In that case, simplyroute the field cable through the core without looping. Use oneferrite suppression core for each RS-232 field wiring circuit.995-8524-4
Q7055C1034, Q7055C1035 FIRE NETWORK ADAPTERS (FNA3)Jameco IS A REGISTERED TRADEMARK OF ARNDT ELECTRONICS.Fair-Rite IS A REGISTERED TRADEMARK OF FAIR-RITE PRODUCTS CORPORATION.TDK IS A REGISTERED TRADEMARK OF TDK KABUSHIKI KAISHA (TDK CORPORATION).DITEK IS A REGISTERED TRADEMARK OF DIVERSIFIED TECHNOLOGIES GROUP, INC.HONEYWELL IS A REGISTERED TRADEMARK AND ENTERPRISE BUILDINGS INTEGRATOR IS A TRADEMARK OF HONEYWELL INC.95-8524-410
Q7055C1034, Q7055C1035 FIRE NETWORK ADAPTERS (FNA3)1195-8524-4
Q7055C1034, Q7055C1035 FIRE NETWORK ADAPTERS (FNA3)Automation and Control SolutionsHoneywell GmbHBoeblinger Straße 1771101 Schoenaich, GermanyHoneywell International Inc.1985 Douglas Drive NorthGolden Valley, MN 55422www.honeywell.com/buildingsolutions U.S. Registered Trademark 2016 Honeywell International Inc.95-8524-4 HSL. Rev. 03-16Printed in Germany
can be connected to the EIA/RS-232 port on the XLS-NCM-EBI with cable P/N 75557 (supplied with XLS-NCM-EBI). A hub or a switch between FNA3 and EBI computer LAN ports is required only if additional network devices are to be connected. IMPORTANT — The DB-9 NUP EIA/RS-232 Field Bus cable
FIRE TOPPER Fire Bowl User Manual Home » FIRE TOPPER » FIRE TOPPER Fire Bowl User Manual Contents [ hide 1 FIRE TOPPER Fire Bowl 2 Setting Up Your Fire Topper Fire Bowl 2.1 Set-Up 3 Placement and Location 3.1 Liquid Propane Tank 4 Using your Fire Topper Fire Bowl - For your safety, read before lighting. 5 Cleaning, Maintenance, Storage 6 .
strong EATON /strong Weatherhead Hose Assembly Master strong Catalog /strong W-HYOV-MC002-E3 February 2011 L-1 Adapters, strong /strong Tube Fittings strong & /strong Connectors Hose to Order & Size Designation L-2 Steel Adapters L-3 thru 16 Swivel Adapters L-17 thru 23 For-Seal Adapters L-24 thru 34 JIC 37 Flare-Twin Fittings L-35 thru 64 Steel Din Fittings L-65 thru 67 Straight Thread O-Rings L-68 thru 70 Din Connectors L-71 /p div class "b_factrow b_twofr" div class "b_vlist2col" ul li div strong File Size: /strong 4MB /div /li /ul ul li div strong Page Count: /strong 108 /div /li /ul /div /div /div
MMC/SD slots. Compact Flash adapters as well as multiple card adapters ( e.g. 6-in-1 adapters) can be used to adapt the PCMCIA slots to different mechanical card formats. Also, the use of card adapters insures low maintenance of the basic PCMCIA sockets on the M6600. Removable adapters are used on the M6600's that are configured for SD/MMC cards.
LOM, which HP calls "FlexFabric Adapters". HP FlexFabric Adapters Embedded on the L460c G7 server motherboard is a dual-port integrated 10Gb HP FlexFabric Adapter, a.k.a. LOM. The server also includes connectors for two dual port FlexFabric 10Gb mezzanine cards. oth types of FlexFabric Adapters enable network convergence when combined a .
social or cultural context (livelihoods, festivals, traditional, conflict) and perhaps regulatory framework (permit fires, illegal fires). The terms include fires, wildfires, wildland fire, forest fire, grass fire, scrub fire, brush fire, bush fire, veldt fire, rural fire, vegetation fire and so on (IUFRO 2018). The European Forest Fire
The Pervasive Data Integration Platform supports more than 1 0 factory-supplied adapters. Most of the Pervasive data adapters have been written to take advantage of native APIs and industry standards. Many of the adapters are available for multiple platforms. Database adapters support a range of modes from client/server access, local database .
Fire Exit Legend Basement N Blood Fitness & Dance Center Fire Safety Plans 7.18.13 Annunciator Panel Sprinkler Room AP SR FIRE FIRE SR ELEV. Evacuation Route Stair Evacuation Route Fire Extinguisher Fire Alarm FIRE Pull Station Emergency Fire Exit Legend Level 1 N Blood Fitness & Dance Center Fire Safety Pl
ASME SA312 ASTM A 312 TP310S Stainless-Steel Tubes ASTM A312 / A 312M, ASME SA312 TP310S is the standard including seamless and welded stainless pipes ASME SA312 TP310S Stainless Steel Pipes ASTM A312 /A312M ASME SA312 Covers seamless, straight-seam welded, and heavily cold worked welded austenitic stainless-steel pipe intended for high-temperature and general corrosive service. ASTM A312 .
