Crimp Specifications - New-Line Hose And Fittings
ated on socket taper)and mark the hose wherethe gage or socket ends.Insert the fitting into thehose until the bottom of thesocket is aligned with themark on the hose or it bottoms out.Step 2: Clean theHose BoreUsing the FT1355-01Jetcleaner or hose compatible solvent, bottle brush,and compressed air, flushcontaminants from the hosebore. See operating instructions for the FT1355-01.Follow shop safety rules.Step 4: Crimp the FittingCrimp the fitting then measure the crimp diameter, ovality dimension (see page 2)and inspect the nipple/socket position. Refer to theCrimp Specification bulletinfor this information. If thehose mark is not within3mm (1/8”) of the socketskirt reject the assembly.Refer to your hose in theHose Style Index for dieselection, finished crimpdiameter, ovality measurements and operating andcrimping instructions.Step 3a: For TTC, TTC12,OTC: Insert the Fittinginto the HoseTo determine the fittinginsertion depth, use theappropriate FF90308 hoseinsertion gage or align theend of the hose with thescribe line (located on socket taper) and mark the hosewhere the gage or socketends. Insert the fitting intothe hose until the bottom ofthe socket is aligned withthe mark on the hose or itbottoms out.Step 5: Plug or Capthe Fittings EndsUse 23055 dust plugs andcaps to protect the fittingthreads and seal out contamination until hoseassembly is installed.EATON Aeroquip Crimp Specifications A-EQCR-TM001-E November 20057
Hose Preparation InstructionsBarrel and Flat Field Crimp Style FittingsSelect a matching hose andfitting combination from thecurrent Aeroquip catalog.Step 1: Cut the HoseCut the hose squarely andto the proper length using asuitable cut off saw. The cutangle must not exceed 5 .Aeroquip recommendsusing saws similar to theS1104. Read the saw operation manual for cuttinginstructions and blade applications.Step 4: Crimp the FittingCrimp the fitting then measure the crimp diameter, ovality dimension (see page 2)and inspect the nipple/socket position. Refer to theCrimp Specification bulletinfor this information. If thehose mark is not within3mm (1/8”) of the socketskirt reject the assembly.8Step 2: Clean theHose BoreStep 3: Insert the Fittinginto the HoseUsing the FT1355-01Jetcleaner or hose compatible solvent, bottle brush,and compressed air, flushcontaminants from the hosebore. See operating instructions for the FT1355-01.Follow shop safety rules.Insert the fitting into hoseuntil the nipple shoulder bottoms against the hose. Markthe hose where the socketends with a grease pencil.Refer to your hose in theHose Style Index for dieselection, finished crimpdiameter, ovality measurements and operating andcrimping instructions.Measure Barrell crimp withAeroquip calidapter (FT1297)and dial calipers or use athread micrometer. Flat Fieldmeasurement does notrequire calidapters.Step 5: Plug or Cap theFitting EndsEATON Aeroquip Crimp Specifications A-EQCR-TM001-E November 2005Use 23055 dust plugs andcaps to protect the fittingthreads and seal out contamination until hoseassembly is installed.
Hose Preparation InstructionsSwage or Flat Crimp Style Fittings(Polyon)Select a matching hose andfitting combination from thecurrent Aeroquip catalog.Step 1: Cut the HoseStep 2: Clean the HoseBoreStep 3: Insert the Fittinginto the HoseUsing the FT1355-01Jetcleaner or hose compatible solvent, bottle brush,and compressed air, flushcontaminants from the hosebore. See operating instructions for the FT1355-01.Follow shop safety rules.Using the bottom edge ofthe fitting part number as areference point, determinethe length of the hose to beinserted into the socket.Mark the hose for insertionlength with a grease pencil.Lightly lubricate the fittingnipple and push the fittingonto the hose leaving thesocket edge even with themark placed on the hose.Do not bottom the hose inthe fitting.Step 4: Swage the FittingStep 5: Crimp the FittingRefer to the FT1242 orFT1282 Swage Machine
Select a matching hose and fitting combination from the current Aeroquip catalog. Step 1: Cut the Hose Cut the hose squarely and to the proper length using a suitable cut off saw. The cut angle must not exceed 5 . Aeroquip recommends using saws similar to the S1104 or FT1500 for large bore and spiral hose, and the FT1258 for FC372 and FC373 .
Crimper Hose Crimp InstructionsCoupling CHART NUMBER REV83 00 mm in Hose Crimp Diameter 111 Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of the ferrule to the Crimp Diameter given in the table.
Automotive Hose and Fittings CONTENT 6 6.1 6.2 6.3 Hose and Fittings 634 G-Line Hose and Fittings 634 Quick Release Couplings 645 600 - 700 Series Hose and Fittings 648 200 Series Hose and Fittings 673 Push Fit Hose and Fittings 679 Adaptors 683 Air Conditioning Hose and 695 Fittings . 634 www.pirtek.com 6. 1 Series Page Hose 910 910 636 Hose 811 811 636 Hose 910 FC 910 FC 636 (Fuel Cell) G .
(approved as fire hose reel) NOHA Hose Trolleys NOHA Hose Reel for long hose legnths NOHA Offshore Hose Reel for wall-mounting MED approved, for wall-mounting Fire Hose Reel industry Fire Hose Reel with foam tank Fire Hose Reel for floor- or wall-mounting Dual Agent Hose Reel 100, 100SW and 100SWA 110 and 110SW 120 300 S50L, S50, S55 Duo, S56 .
600 PSI Concrete Placement Hose - 800 PSI Concrete Placement Hose - 1300 PSI Non-Conductive Furnace Door Hose Drilling Mud, Oilfield Suction and Discharge Hose - 150 PSI Blue Low Temp Petroleum Suction Hose - Corrugated Oilfield Suction & Discharge Hose - 150 PSI Oilfield Vac Hose - 150 PSI Nitrile Petroleum Suction Hose - 300 PSI Oil Return .
Agilent 1290 Infinity X Agilent G1888A Agilent 7673A X Agilent 7683A X Agilent HS7694 Agilent 7695A Agilent 79855(A) X Agilent 5880 X Agilent 5890 X . Autosampler Compatibility Chart Crimp Neck ND8 1 1. Snap Ring ND11 Screw Neck ND13 Shell Vials Shell Vials Shell Vials Shell Vials Headspa
M39012/20-0504 D VIa Econo-Crimp 10-10005-006 3 Straight Cable Plugs (M39012/16) M39012 P/N Category Cable Group Cable Attachment Automatic P/N Figure M39012/16-0013 C VIa Econo-Crimp 10-01009-001 1 M39012/16-0014 C VIb Econo-Crimp 10-01009-002 1 M39012/16-0015 (1) C VIIa Econo-Crimp 10-01009-003 1 M39012/16-0016 C IV Econo-Crimp 10-01009-004 1 .
Willcox Composite Hose 3 Anatomy of a Willcox Hose 4 3081PGP Light Duty Polypropylene Chemical Hose 6 3091PGP Heavy Duty Polypropylene Chemical Hose 7 3094PSP Heavy Duty Polypropylene Acid Chemical Hose 8 4091SGP, 4094SSP Heavy Duty Polypropylene Chemical Hose 9 4121SGF, 4124SSF Fluoropolymer Chemical Hose 10 .
using artificial intelligence (AI)—and machine learning in particular—increasingly match or surpass human-level performance; news about the rapid pace of technological advancement abounds, and market capitalizations for technology firms are at all-time highs. Yet, measured productivity growth in the United States has declined by half over the past decade, and real income has stagnated .
