Easytouch Control System Indoor Control Panel 8 And 4 For .
EASYTOUCH CONTROL SYSTEMINDOOR CONTROL PANEL 8 AND 4FOR POOL AND SPAAUTOHEATERSPA100 F / 95 FAIR 77 FMON 09:30 AMINSTALLATIONANDUSER’S GUIDEIMPORTANT SAFETY INSTRUCTIONSREAD AND FOLLOW ALL INSTRUCTIONSSAVE THESE INSTRUCTIONS
2016 Pentair Water Pool and Spa, Inc. All rights reservedThis document is subject to change without notice1620 Hawkins Ave., Sanford, NC 27330 (800) 831-7133 (919) 566-800010951 West Los Angeles Ave., Moorpark, CA 93021 (800) 831-7133 (805) 553-5000P/N 520617 Rev G - 7/2106
iContentsIMPORTANT WARNING AND SAFETY INSTRUCTIONS .EasyTouch Indoor Control Panel Kit Contents .Related Manuals .EasyTouch Accessories .Technical Support .iiivvvviSection 1: EasyTouch Indoor Control Panel Overview . 1EasyTouch Indoor Control Panel .Operating EasyTouch .EasyTouch Systems .EasyTouch Indoor Control Panel Overview .EasyTouch Indoor Control Panel Buttons .EasyTouch Indoor Control Panel Display .111235Quick Start - Pool and Spa Operations (Shared Equipment) . 6Heating the Spa .Heating the Pool .Adjusting the water temperature setting .Schedule start and stop times for equipment .Controlling Lights .EasyTouch Wireless Control Panel (Accessory) .iS4 Spa-Side Remote Controller (Accessory) .iS10 Spa-Side Remote Controller (Accessory) .QuickTouch QT4 Wireless Controller (Accessory) .666778899Section 2: EasyTouch Menus . 9EasyTouch Menus .Main Screen .Feature Circuits Menu .Lights Menu .The Color Swim and Color Set Lighting Features.Setting up Lights .Assign the Circuit Name and Function .Setting up IntelliBrite Light Circuits .Lights Menu .Modes (IntelliBrite Color light shows, Color Swim, Color Set) .Modes (Color Swim) .Modes (Color Set) .Colors .Hold/Recall .All On / All Off (Lights Menu) .Sync .Config .Setting up SAM, SAL, PG2000, Color Wheel Lights .Setting up MagicStream Laminars .Using the MagicStream Laminars Features .Heat Menu .Pool Temp/Src .Spa Temp/Src .Delay Cancel Menu .Schedules Menu .Schedule Daily Spa/Pool Operations .Using the Once Only feature .Using the Egg Timer (countdown) Feature .Settings Menu: Clock .Settings Menu: IntelliFlo 12223242525EasyTouch Indoor Control Panel Installation and User’s Guide
iiContentsSettings Menu: IntelliFlo (VS and VSF SVRS) .Settings Menu: IntelliFlo (VF) .Settings Menu: IntelliChlor .Settings Menu: IntelliChem .Settings Menu: Heat Pump COM (UltraTemp) .Settings Menu: Circuit Names .Hi-Temp/Lo-Temp Controls for Single Body System.EasyTouch Circuit Names (Complete List) .Settings Menu: Circuit Functions .Freeze Protection .Preset Circuit Function Names (Complete List) .Settings Menu: Custom Names.Settings Menu: Valves .Settings Menu: 2-Speed Pump .Settings Menu: Solar .Settings Menu: Delays .Settings Menu: F / C (Fahrenheit/Celsius) .Settings Menu: iS4 Spa-Side Remote Controller .Settings Menu: iS10 Spa-Side Remote Controller .Settings Menu: iSx Pump Crtl .Settings Menu: QuickTouch (QT4) Wireless Remote .Settings Menu: Man Heat (Off/On).Settings Menu: Calibration .Settings Menu: Erase EEPROM (Erase System Memory) .Settings Menu: Set Password .Spa Side [Off/On] .Diagnostics Menu: Software Rev .Diagnostics Menu: Bootloader Rev .Diagnostics Menu: Self Test .Diagnostics Menu: Chlorinator .Diagnostics Menu: Water Temp .Diagnostics Menu: Solar Temp .Diagnostics Menu: Air Temp .Diagnostics Menu: Cir Name: [Off/On] .Diagnostics Menu: Reset System .Diagnostics Menu: Flash Update .Section 3: Troubleshooting 7484848495050505151515153Frequently Asked Questions (FAQ) .EasyTouch Error Messages .Self Test Error Codes .Error Code Table .Maximum Programs Exceeded .IntelliChlor Error Messages .Problem: iS10 fails to operate. .System Problem Diagnosis .Problem: iS4 fails to operate. .Problem: The Quick Touch remote will not work, or will not work dependably. .EasyTouch System Wiring Diagram .First Time Start Up .Wiring a ThermalFlo Heat Pump to an EasyTouch Control System .Synchronizing control panels.5354545455555656565758596060Section 4: EasyTouch Indoor Control Panel Installation . 61Glossary . 66EasyTouch Indoor Control Panel Installation and User’s Guide
iiiIMPORTANT WARNING AND SAFETY INSTRUCTIONSImportant Notice:Attention Installer: This manual contains important information about the installation, operation andsafe use of this product. This information should be given to the owner and/or operator of this equipment.WARNING - Before installing this product, read and follow all warning notices and instructions which areincluded. Failure to follow safety warnings and instructions can result in severe injury, death, or propertydamage. Call (800) 831-7133 for additional free copies of these instructions.WARNING - Water temperature in excess of 100 degrees Fahrenheit may be hazardous to your health.Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the internal temperatureof the body reaches a level several degrees above normal body temperature of 98.6 F (37 C). The symptomsof hyperthermia include drowsiness, lethargy, dizziness, fainting, and an increase in the internal temperature ofthe body.The effects of hyperthermia include: 1) Unawareness of impending danger. 2) Failure to perceive heat. 3) Failureto recognize the need to leave the spa. 4) Physical inability to exit the spa. 5) Fetal damage in pregnant women.6) Unconsciousness resulting in danger of drowning.WARNING - To reduce the risk of injury, do not permit children to use this product unless they are closelysupervised at all times.WARNING - The use of alcohol, drugs, or medication can greatly increase the risk of fatalhyperthermia in hot tubs and spas.WARNING - Control System is intended to control heaters with built-in high limit circuits ONLY. Failure to doso may cause property damage or personal injury.WARNING - Do not use this product to control an automatic pool cover. Swimmers may become entrappedunderneath the cover.WARNING - For units intended for use in other than single-family dwellings, a clearly labeled emergencyswitch shall be provided as part of the installation. The switch shall be readily accessible to the occupants andshall be installed at least 10 feet (3.05 m) away, adjacent to, and within sight of, the unit.CAUTION - Except for listed spa-side remote controls, install a minimum of five (5) feet from the inside wallof the pool and spa.Two Speed Pump Controls Notice (Title 20 Compliance)Please read the following important Safety Instructions (See page 40 for pump speed setup)When using two-speed pumps manufactured on or after January 1, 2008, the pump’s defaultcirculation speed MUST be set to the LOWEST SPEED, with a high speed override capability beingfor a temporary period not to exceed one normal cycle, or two hours, whichever is less.EasyTouch Indoor Control Panel Installation and User’s Guide
ivIMPORTANT WARNING AND SAFETY INSTRUCTIONSGeneral Installation Information1. All work must be performed by a licensed electrician, and must conform to all national, state, and localcodes.2. Install to provide drainage of compartment for electrical components.3. If this system is used to control underwater lighting fixtures, a ground-fault circuit interrupter (GFCI)must be provided for these fixtures. Conductors on the load side of the ground-fault circuit-interruptershall not occupy conduit, junction boxes or enclosures containing other conductors unless suchconductors are also protected by a ground-fault circuit-interrupter. Refer to local codes for details.4. A terminal bar stampedis located inside the supply terminal box. To reduce the risk of electricshock, this terminal must be connected to the grounding means provided in the electric supply servicepanel with a continuous copper wire equivalent in size to the circuit conductors supplying thisequipment (no smaller than 12 AWG or 3.3 mm). The bonding lug(s) provided on this unit are intendedto connect a minimum of one No. 8 AWG for US installation and two No. 6 AWG for Canadianinstallations solid copper conductor between this unit and any metal equipment, metal enclosures orelectrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit.5. The electrical supply for this product must include a suitably rated switch or circuit breaker to open allungrounded supply conductors to comply with Section 422-20 of the National Electrical Code, ANSI/NFPA 70.1987. The disconnecting means must be readily accessible to the tub occupant but installedat least 10 ft. (3.05 m) from the inside wall of the pool.6. Supply conductor must be sized to support all loads. Maximum supply conductor current must be 125Amps at 125 VAC.EasyTouch Indoor Control Panel Installation and User’s Guide
vEasyTouch Indoor Control Panel Kit ContentsThe following items are included in the EasyTouch indoor control panel kit. If any items are missing pleasecontact Pentair Technical Support (see page vi). EasyTouch indoor control panel Plastic anchors and mounting screws EasyTouch Indoor Control Panel Installation and User’s Guide (this manual)Related Manuals EasyTouch 8 and 4 Pool and Spa Control System User’s Guide (P/N 520584) EasyTouch 8 and 4 Installation Guide (P/N 520583)EasyTouch AccessoriesEasyTouch Indoor Control Panel, 4 Circuits(P/N 520548)EasyTouch Indoor Control Panel, 8 Circuits(P/N 520549)EasyTouch Wireless Control Panel, 4 circuits(P/N 520546)EasyTouch Wireless Control Panel, 8 circuits(P/N 520547)iS4 Four-Function Spa-Side remote, 150 ft. cable(P/N 520094)iS10 Ten-Function Spa-Side remote, 150 ft. cable(P/N 520149)(P/N 520148)QuickTouch four-function wireless remote kit with transceiver assemblyIntelliChlor Acid Cleaning Kit(P/N 520670)IntelliChlor Spacer pass-through cell for new pool start-up(P/N 520588)IntelliChem: P/N 521357 (no pump), P/N 521356 (one pump), P/N 521355 (two pump)POWER ONEasyTouch 4 Indoor ControlPanel (P/N 520548)iS10 Spa-SideRemote Controller (P/N 520149)EasyTouch 8 Indoor ControlPanel (P/N 520549)EasyTouch Wireless Control Panel(8 circuit) (P/N 520547)iS4 Spa-Side RemoteController (P/N 520094)EasyTouch Indoor Control Panel Installation and User’s Guide
viTechnical SupportContact Technical Support at:Sanford, North Carolina (8 A.M. to 5 P.M.)Phone: (800) 831-7133Fax: (919) 566-8920Moorpark, California (8 A.M. to 5 P.M.)Phone: (800) 831-7133 (Ext. 6312)Fax: (805) 553-5515Web sites: visit www.pentairpool.com and www.staritepool.comEasyTouch Indoor Control Panel Installation and User’s Guide
1Section 1EasyTouch Indoor Control Panel OverviewEasyTouch Indoor Control PanelThe EasyTouch Indoor Control Panel provides you with one touch automatic control for all of your pool andspa daily operations from inside your home. The EasyTouch Indoor Control Panel is designed to be used withthe EasyTouch 8 or EasyTouch 4 system.Operating EasyTouchThe EasyTouch system can automatically control your pool and spa equipment, lights and other optionalequipment. You can also control all of the EasyTouch system operations from the outdoor control panel locatedin the Load Center at the pool equipment pad. Using the outdoor control panel buttons you can manuallyoverride any automatic settings. For more information, refer to the EasyTouch User’s Guide (P/N 520584).If required, the EasyTouch Indoor Control panel can be password protected. To access a password protectedcontrol panel, simply enter the four digit assigned password (see page 47).EasyTouch SystemsThere are two EasyTouch system configurations available; EasyTouch 8 (auxiliary circuits) and EasyTouch 4(auxiliary circuits). The EasyTouch system is factory configured to operate with a “shared” equipment systemor with a “single body” system. For EasyTouch 4 and EasyTouch 8 menu settings, see page 5.AUTOHEATERSPA100 F / 95 FAIR70 FMON 09:30 AMEasyTouch 8 Indoor Control PanelEasyTouch Indoor Control Panel Installation and User’s Guide
2EasyTouch Indoor Control Panel OverviewThe EasyTouch Indoor Control Panel makes it easy for you to control your pool and spa daily operations frominside your home. Using the “Pool” and “Spa” buttons allows one touch control to heat and filter your spa andpool. EasyTouch automatic system operations can be performed either at the Indoor Control Panel or from theoutdoor control panel. The Indoor Control Panel connects to the motherboard in the EasyTouch load center.Spa (Hi-Temp) Button: Switches the filterpump on, rotates valve actuator (to isolatespa water from pool water), and switchesthe heater on. Hi-Temp (EasyTouch singlebody system) sets the high temperaturesettings for the spa, see page 35.Pool (Lo-Temp) Button:Switches the filter pump on,rotates valve actuator (to isolatepool water from spa water), andswitches heater on.Lo-Temp (EasyTouch single bodysystem) sets the lowtemperature settings for the pool,see page 35.For details about the controlpanel LCD status messages,see page 5.Circuit LED.Circuit name label.AUTOHEATERSPA100 F / 95 FAIR70 FMON 09:30 AMSet Temperature buttons,see page 4.Menu/Back button,see page 4.Indoor Control Panel (EasyTouch 8) - (P/N 520549)Pool (Lo-Temp) Button:Switches the filter pump on,rotates valve actuator (to isolatepool water from spa water), andswitches heater on.Lo-Temp (EasyTouch single bodysystem), can be assigned for lowtemperature setting, see page 35.Seven user definedauxiliary circuits.Buttons switch theassigned circuitfunction on/off (12hour time-out). If solarequipment is not beingused, use the AUXEXTRA (Down arrowbutton) for an additional circuit (see page4 for details).Spa (Hi-Temp) Button:Switches the filter pump on,rotates valve actuator (toisolate spa water from poolwater), and switches theheater on. Hi-Temp(EasyTouch single bodysystem), Can be assigned forhigh temperature settings,see page 35.Circuit LED.Circuit namelabel.AUTOHEATERSPA100 F / 95 FAIR70 F FRZMON 09:30 AMSet Temperature buttons,see page 4.Indoor Control Panel (EasyTouch 4) - (P/N 520548)EasyTouch Indoor Control Panel Installation and User’s GuideThree auxiliary buttonsswitch the assignedcircuit function on/off(12 hour time-out). Ifsolar equipment is notbeing used, use theAUX EXTRA (Downarrow button) for anadditional circuit (seepage 4)
3EasyTouch Indoor Control Panel ButtonsYou can fully automate your pool, spa, and lighting operations from the EasyTouch Indoor Control Panel orfrom the EasyTouch outdoor control panel located at the pool equipment pad. The EasyTouch menu featureslet you create customized schedules for your pool and spa equipment, heat temperatures, and chlorinationsettings to switch on and off at a set day and time. Scheduled automatic operations can be performed at theEasyTouch Indoor Control Panel or from the outdoor control panel. For menu options, refer to “EasyTouchMenu Structure,” on page 9. Before operating the EasyTouch Indoor Control Panel, familiarize yourself withthe LCD status messages and control buttons.123AUTOHEATERSPA100 F / 95 FAIR70 FMON 09:30 AM84567EasyTouch Indoor Control PanelEasyTouch Indoor Control Panel ButtonsSpa button/LED: For spa operations. Press the Spa button to activate the filter pump, rotate the12P pool/spa valve actuators and circulate the spa water (LED on). Press the button again to switch thefilter pump off (LED off). While the valves are rotating into position the filter pump will switch off.For service or testing purposes, if the heater is enabled in the Heat menu, pressing this button willalso activate the heater. For normal spa operations the heater is automatically switched on with thefilter pump (see Man Heat page 46) regardless of the Heat menu setting. When this button ispressed the circuit is activated, the LED is on and “SPA” is displayed on the screen with the currentand set point water temperatures. Once the filter pump is switched on it will run for 12 hours unlessit is switched off. When this button is pressed, the LEDs on the outdoor control panel Filter Pump (F)button, Valves (V) button, and Heater button (if enabled in the Heat menu) will be on. If this displayline is blank, it indicates no spa or pool function is currently active.Pool Button: For pool operations. Press the Pool (P) button to activate the filter pump, rotate thepool/spa valve actuators and circulate the pool water and switch on the heater (if enabled in theHeat menu). Press the button again to switch the filter pump off. While the valves are rotating intoposition the filter pump will switch off. When this button is pressed the circuit is activated and“POOL” is displayed on the screen with actual and set point water temperatures. When the filterpump is switched on it will run for 12 hours unless it is switched off. When this button is pressed, theLEDs on the outdoor control panel Filter Pump (F) button, Valves (V) button, and Heater button (ifenabled in the Heat menu) will be on. If this display line is blank, it indicates no pool or spa functionis currently active.EasyTouch Indoor Control Panel Installation and User’s Guide
4Controls and buttons (Continued)Pool button (Continued) Single-Speed Filter Pump: If the pump is currently off, press the Pool button to switch the pumpon. Press the Pool button again to switch the pump off. However, if the heater is operating, and adelay is enabled for valves, this allows the heater to cool down (heater cool-down), then when youpress the Pool button to switch off the pump, only the heater will turn off, then the filter pump willautomatically switch off after 10 minutes to allow the heater to cool down. Pentair Water Pool andSpa heaters do not require a cool down time. To override the “heater cool-down,” press the Poolbutton again to switch off the pump. Two-Speed Filter Pump: Press the Pool button to switch the two-speed pump on in high speed.Press the Pool button again to run the pump in low speed. In order to use the “2-Speed Pump” menuassignments (see page 40), the 2-Speed relay option must be installed in the EasyTouch LoadCenter.Notes about Freeze Protection: This function protects the pool, plumbing, and equipment againstfreeze damage. If the outside air temperature sensor falls below 36 F (2 C), “Freeze Protection” isactivated and the Filter Pump relay is switched on to circulate the pool water. To enable freezeprotection for a circuit, see “Settings Menu: Circuit Functions, ” on page 37.Liquid Crystal Display (LCD): The main system display consists of a 16 x 4 alphanumeric characterLCD with EL backlighting for easy viewing of the menu items, and status messages. Press theMenu button twice to refresh the display. For main screen status information, see page 5.34 Menu/Back button: Press the Menu/Back button to access, save and exit the EasyTouch system5MENU6 SELECT7Left button: When in pool or spa mode, press the Left button to lower the set point watertemperature. Press the Spa or Pool (Up arrow P) button (page 3) to display the current watertemperature. While in the main menu, press the Left button to scroll through sub-menu selections,setting and values. While editing settings, press and hold the Left button to fast reverse throughsettings and values. menu settings. Use this button to exit from main menu or sub-menu items. Pressing the Menu/Backbutton while in a menu item will return to the mai
There are two EasyTouch system configurations available; EasyTouch 8 (auxiliary circuits) and EasyTouch 4 (auxiliary circuits). The EasyTouch system is factory configured to operate with a "shared" equipment system or with a "single body" system. For EasyTouch 4 and EasyTouch 8 menu settings, see page 5. EasyTouch 8 Indoor Control Panel
EasyTouch System Overview EasyTouch Indoor Control Panel The EasyTouch Indoor Control Panel provides you with one touch automatic control for all of your pool and spa daily operations from inside your home. The EasyTouch Indoor Control Panel is designed to be used with the EasyTouch 8 or EasyTouch 4 system. Operating EasyTouch
The EasyTouch Indoor Control Panel is designed to be used with the EasyTouch 8 or EasyTouch 4 system. Operating EasyTouch The EasyTouch system can automatically control your pool and spa equipment, lights and other optional equipment. You can also control all of the EasyTouch system operations from the outdoor control panel located
EasyTouch 8 and 4 Pool and Spa Control System Kit Contents The following items are included in the EasyTouch 8 and EasyTouch 4 control system kit which may also include the IntelliChlor cell. † EasyTouch control panel (mounted in the load center) † EasyTouch load center enclosure
EasyTouch Pool and Spa Control System User's Guide EasyTouch 8 or 4 System Kit Contents The following items are included in the EasyTouch 8 or 4 System kit. If any items are missing, please contact Pentair Technical Support (see page vi). † EasyTouch control panel (mounted in the load center) † EasyTouch load center enclosure
EasyTouch 8 and 4 Pool and Spa Control System Kit Contents The following items are included in the EasyTouch 8 and EasyTouch 4 control system kit which may also include the IntelliChlor cell. If any items are missing please contact technical support. † EasyTouch control panel (mounted in the load center) † EasyTouch load center enclosure
EasyTouch Pool and Spa Control System User's Guide EasyTouch 8 or 4 System Kit Contents The following items are included in the EasyTouch 8 or 4 System kit. If any items are missing, please contact Pentair Technical Support (see page vi). † EasyTouch control panel (mounted in the load center) † EasyTouch load center enclosure
EasyTouch Wireless Control Panel Installation and User's Guide EasyTouch Wireless Control Panel Kit Contents The following items are included in the EasyTouch wireless control panel kit. If any items are missing please contact Pentair Technical Support (see page vi). † EasyTouch wireless control panel † Four AA-size alkaline batteries
Bereavement counseling includes a broad range of transition services including outreach, counseling, and referral services for family members. There is no cost for VA bereavement counseling. More information is available by contacting the Readjustment Counseling Service at 202-461-6530 or online at the . Vet Center website. Army
