Rolling Ladder Hardware - Van Dyke's

Quiet Glide & InvisiDoor3Rolling Library Ladders Select Rail ComponentsSelect Rail ComponentsStraight Rail - Three Different LengthsSKURail Length208458FinishSplice Kit for Joining Round Rails TogetherWall-Mounting Bracket for Round RailsChoose brackets, based on the top roller choice youmade (in Step 1). Sold as each. Screws are included.EachSatin Nickel4'2084584'2084584'Chrome 105.002084584'Oil Rubbed Bronze 50.002084584'Black2084586'2084586'2084586'Chrome 159.002084586'Oil Rubbed Bronze 71.002084586'Black208454ChromeSatin Nickel208454Oil Rubbed Bronze208454BlackHamm. Antique Brass 50.00SKUSize210317Vertical Rolling/Swivel BracketKit1 2” x 1 8” barFor use with Standard TopRollers and Swivel Rollers. 9.00Satin NickelHamm. Antique Brass 71.002084588'2084588'2084588'Oil Rubbed Bronze 94.002084588'Black 86.00Hamm. Antique Brass 94.00SKUThread Tap AccessoryAccessory used to make threads at the end of rails forend caps.SKU226192Size1 4” x 20 tap208454FinishSatin Nickel208454Hamm. Antique BrassEachEach 8.00Vertical Rolling Hook Bracket135-Degree Curved Rail*For use with Rolling Hook toprollers.Standard End Cap Kit for Round Rails135º Inside Corner30” Radius; 5’ LengthMade out of solid steel. Each kit includes 2 caps (1 1/4”dia.) and 2 fastening bolts (1/4” #20 x 18mm)*Not compatible with Rolling Hook hardwareSKU226195FinishSatin NickelEach 189.00226195Hammered Antique Brass 189.00226195Oil Rubbed Bronze226195Black90-Degree Curved Rail*208457SKUFinishSatin Nickel208457Hammered Antique Brass*208457Chrome208457Oil Rubbed Bronze208457BlackKit* Pattern may varyBall End Cap Kit for Round RailsSKU208655FinishSatin NickelEach 189.00208655Hammered Antique Brass 189.00208655Oil Rubbed Bronze208655BlackMade out of aluminum. Ball cap measures 1 1/2” dia. andhas a 1/4-20 screw. Each kit includes 2 ball caps.SKU90-Degree Curved Rail*90º Inside Corner16” Radius; 5’ LengthHamm. Antique Brass226204Oil Rubbed Bronze226204Black220876FinishSatin Nickel220876Hammered Antique Brass*220876Oil Rubbed Bronze220876BlackChrome208454Oil Rubbed Bronze208454BlackFinishSatin Nickel208729Hamm. Antique Brass208729Chrome208729Oil Rubbed Bronze208729BlackEachHorizontal Rolling Hook BracketEachMade with solid steel and plated Chrome. For use whencutting chrome rails to conceal chipping. Each kitincludes 2 caps and 2 fastening bolts (1/4” #20 x 18mm)FinishChromeSKU208729For use with Rolling Hook top rollers.End Cover Kit for Chrome RailsSKU236167* SOI SPECIAL ORDER ITEMHamm. Antique Brass208454Kit* Pattern may vary*Only use with Swivel hardware*Not compatible with Rolling Hook hardware226204208454EachHorizontal Rolling/Swivel Bracket*Only use with Swivel hardware*Not compatible with Rolling Hook hardwareFinishSatin NickelFinishSatin NickelFor use with Standard Top Rollers and Swivel Rollers.90º Inside Corner30” Radius; 5’ LengthSKU226204SKU208454KitSKU226237FinishSatin Nickel226237Hammered Antique Brass226237Chrome226237Oil Rubbed Bronze226237BlackEachThese brackets are used to mount the round rail to thewall. You will need 1 bracket for every 32", or 4 bracketsfor an 8' rail. Wall brackets must be mounted securelyinto studs.10 Browse our wholesale hardware, RTA cabinets, rolling ladders and more online at www.cshardware.com

General Installation/Specification GuideStep 1: Rail InstallationSpecial application notes: Leave at least 7” of clearance between the center of the rail and the ceiling, crownmoulding or other overhanging protrusions when the ladder is in the stored position(close to the wall/cabinet/bookshelf). In the climbing position, a minimum 3” clearancebetween the center of the rail and any upper cabinet doors is required to be able to openthe upper cabinet doors. Do not mount rail brackets directly onto a drywall surface. Always mount these bracketsto solid wood, predrilling the holes in the wood is advisable to avoid splitting the wood.1. Establish the height of where the center of the rail is to be installed and mark the locationwhere the bottom of the mounting bracket will be located (depending on which type ofbracket is used, the distance between the center of the rail and the bottom of the bracketwill change, see dimensional specs on the bracket those measurements). Verify with aquality leveling device that the lateral locations of the brackets are level and true.2. To splice rails together using the Quiet Glide splice kit (210317) complete the followingsteps: Insert the roll pin halfway the length of the pin into one of the rails Slide the steel bar halfway into the rail and tighten 2 of the set screws to lock thebar and roll pin onto the rail. Line up the roll pin hole and slot for the steel bar on the other rail and slide therail over the pin and bar till a tight connection is made between rails. Complete the splice by tightening the remaining 2 set screws3. Slide all the brackets to be used onto the rail, recommended spacing of the brackets isapproximately 32” apart.4. Secure each bracket to the wood surface with the screws included.Step 2: Ladder Assembly (if applicable)(It is recommended that the ladder rail sides and steps are sanded slightly with a 220 grit sandpaper just prior to applying the finish (stain, paint, clear coat sealer) on the ladder. It is alsomuch easier to finish the ladder prior to assembly, taking care to protect the inside of the dadosof the side rails and the ends of the steps from the applied finish that would prevent a goodstrong glue bond between the steps and the side rails)1. Stand on edge one of the ladder side rails on a flat surface, dados facing away from you.2. Insert one of the steps into the dado, aligning the compound miter of the step flush withthe dadoed surface of the side rail. If not flush, flip and/or rotate the step until it lines upproperly with the side rail.3. Once proper alignment of the step is established, apply a thin film of qualitywoodworker’s glue to the end of the step and also in the dado.4. Using the supplied 1-3/4” washer-head screws, secure the step to the side rail through thepredrilled holes on the side rails. Assemble the remaining steps in the same manner.7

5. Once all the steps are assembled onto one of the side rails, position the side rail on itsside with the steps pointing up.6. Apply a thin film of glue on the ends of each step and in the dado of the other rail, alongwith the holes in the sides of the rail (for the top turned rung) and the ends of the topturned rung.7. Properly align each step as well as the top turned rail into its corresponding dado/hole,use the supplied 1-3/4” washer-head screws to fasten the steps into place.8. To install the step support rods, push a nut cap (used with the step support rods) in thepredrilled hole on the side rail. Slide the step support rod through the hole on theopposite side rail and partially thread it into the nut cap. Install the other nut cap andusing two 5mm Allen wrenches tighten each side simultaneously so that there is equalamounts of thread on each end of the rod into each nut cap.Step 3 Ladder Hardware InstallationTop Ladder Hardware1. Align the top roller guide on the beveled portion of the top of the ladder so that the topturned rung is centered between the bolt holes on the side of the hardware.2. Mark on the beveled flat surface of the ladder, the top of the hardware. Measure from thetip of the ladder to this mark. Scribe a similar mark on the other ladder side rail so thatthe location of the top roller guide will be identical on both of the ladder side rails.3. Locate the top roller guide onto the ladder rail, lining up this hardware on the scribedline. Using a Vix bit or similar self-centering drill guide, drill a pilot hole into the edgeof the ladder for the (2) #10 x ¾” Flat-head, Phillips-drive screws, and secure each toproller guides to the top of the ladder.4. Using a ¼” drill bit, drill out the holes for the ¼-20 KD bolts on the sides of the ladder.Recommended procedure for this: Using the holes in the top roller guide as a drill guide, drill a ¼” hole half waythrough the thickness of the ladder slide rail. Drill the same hole on the opposite side of the top roller guide, producing a ¼”through hole in the ladder side rail. Follow this same procedure for all 4 through holes and complete the assembly bysecuring the top roller guide with the supplied ¼-20 KD bolts and acorn nuts.Bottom Ladder Hardware1. Place the bottom roller housing onto the bottom of the ladder using the “U” bracketportion of the housing. Verify that the bracket is flush with the bottom of the ladder.Because of the 12-degree angle of the bottom of the ladder this will align the housingdiagonally across the ladder side rail.2. Mark the location of the “U” bracket on the bottom of the ladder and at the same timemark on the side of the ladder the location of the top mounting hole of the bottom rollerhousing. Measure these marks and transfer these measurements to the other ladder siderail so that the hardware will mount identically on both ladder side rails.3. Using a ¼” drill bit, drill a through hole in the ladder side rail for the ¼-20 KD bolt.4. Predrill the ladder side rail for the #10 x ¾” screw5. Install both the bottom roller guides using the included screws and KB bolts and acornnuts.8

Bottom Ladder HardwareTop Ladder HardwareTop Roller7/8”Rolling Hook4” CC5-1/2”2-1/8” dia6-1/2”4” CC5-1/2”Brake Wheel7/8”6-1/2”2-1/2”1-3/4”2” dia8-1/4”1-3/4”5-1/2”4”Double Hook *1-3/4”Adjustable Hook53/64”*7/8”6-1/8”7/8”Standard 13/64”4” CC8”1-3/4”3-7/8”3-5/16”27/32”7/8”* Designed For Loft ApplicationsTop Swivel Roller5-7/8”7/8”Contemporary WheelNon - Skid Foot1-7/16”1-1/45-1/2”6-1/2”4” CC5”7/8”3”5-3/8”1-3/4”5-1/2”Rail Height and distanceTop Ladder ClearanceHand Rail dimensions7”for 8’, 9’, 10’ standard ladders7”to floor45 angle(approximately)5” radiusStock 1-1/4” x 1-1/4”with 3/16” radius corners5/8” radius ends2- Predrilled holes 17/64”2-1/8”CC on each endlocated 3/4” from end”C”C47”47”3/4/82-1Approximately9

Curved rail radius dimensions1-3/8”Hook top Hardware cannot be used with curved rails!BracketSplice kitRail Diameter 1”90 BracketRail Height & Ladder DistancVertical Rail BracketsFor Roller and Swivel Top Guidessiu0”3dRa7/8”2”CC 2-5/8” 115”Straight sectionof curved rail141-3/4”2”103”/-1Rail heights( center of Rail )6”Protrusion91”2-3/8”23/32”38”For Hook and Rolling Hook Top Guides15/16”8’135 21.7”Distance from wall ( ladder in climbing positioStraight sectionof curved railRev ”1-3/4”RadBracketSplice kit9’ 10’19.35”2-1/16”CC2-11/16”21”Horizontal Rail Brackets3 -7/8”28-3/4”For Roller and Swivel Top Guides1-3/8”BracketSplice kit90 7/8”7/8”15/16”Bracket1-3/4”sFor Hook and Rolling Hook Top Guidesiu”16dRaStraight sectionof curved rail1”CC17”9”35-1/2”Center of ttom ofHorizontal Bracket

11

Make your own Ladder45-DegreeBevelTo determine length of ladder: Measure from the center of rail to the floor,then add five inches to the measurement.7/8” Dia x 1/2” Deep Hole.15-3/8” and 19-3/8” OAL14-3/8” and 18-3/8” Inside1-1/4” Dia. to 1-1/8” Dia. Taper13/1613/1616”/20”Distance varies depending onlength of laddernnt oatePesivexcluwarg-EniarddHnpPek ToentHooPatgnilRolRolling Ladder Hardware KitsRolling Hookupper guideRollerupper guideLimited Lifetime warranty1/16/19

Rolling Library Ladders Hardware Kits 1A Select an Upper and Lower Hardware Kit Made in the USA! Contemporary Wheel with Standard Roller Kits SKU Ladder Width Color Kit 226212 16" Satin Nickel 226212 16" Hamm. Antique Brass 226212 16" Oil Rubbed Bronze 226212 16" Black 236168 20" Satin Nickel 236168 20" Hamm. Antique Brass 236168 20" Oil Rubbed .