Wm 900 S,P (Rev 7) - Multiquip Inc
PARTS AND OPERATION MANUALPLASTER / MORTAR MIXERS COPYRIGHT 2001, MULTIQUIP INC.WM-900SWM-900PRevision #7 (03/17/06)MULTIQUIP INC.PARTS DEPARTMENT:18910 WILMINGTON AVE.800-427-1244CARSON, CALIFORNIA 90746 FAX: 800-672-7877SERVICE DEPARTMENT/TECHNICAL : 310-537-3927FAX: 310-631-5032E-mail:mq@multiquip.com www:multiquip.com
PAGE 2 — WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06)
HERE'S HOW TO GET HELPPLEASE HAVE THE MODEL AND SERIAL NUMBERON-HAND WHEN CALLINGPARTS DEPARTMENT800-427-1244 or 310-537-3700FAX: 800-672-7877 or 310-637-3284SERVICE DEPARTMENT/TECHNICAL ASSISTANCE800-478-1244 or 310-537-3700FAX: 310- 537-4259WARRANTY DEPARTMENT888-661-4279, or 310-661-4279FAX: 310- 537-1173MAIN800-421-1244 or 310-537-3700FAX: 310-537-3927WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06) — PAGE 3
TABLE OF CONTENTSHere's How To Get Help . 3Table of Contents . 4Parts Ordering Procedures . 5Rules for Safe Operation & Safety Decals . 6Warranty . 7WHITEMAN — 900S & 900POperations . 8-10Specifications . 11Explanation Of Codes In Remarks Column . 12Suggested Spare Parts . 13Drum Head Assembly . 14-15Paddle Shaft Assembly . 16-17Steel Drum (S) . 18-19Polyethylene Drum (P) . 20-21Gas Engines, Pulleys & Cab Assembly . 22-23Electric Motor & Pulleys . 24-25Axle & Wheel Group . 26-27Terms and Conditions Of Sale — Parts . 28NOTE: Specification and part numberare subject to change without notice.PAGE 4 — WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06)
www.multiquip.comEffective: June 1st, 2005PARTS ORDERING PROCEDURESOrdering parts has never been easier!Choose from three easy options:Best Deal!Order via Internet (Dealers Only):If you have an MQ Account, to obtain aUsername and Password, E-mail us at:parts@multiquip.com.Order parts on-line using Multiquip’s SmartEquip website! View Parts Diagrams Order Parts Print Specification InformationTo obtain an MQ Account, contact yourDistrict Sales Manager for more information.Use the internet and qualify for a 5% Discounton Standard orders for all orders which includecomplete part numbers.*Goto www.multiquip.com and click onOrder Parts to log in and save!Note: Discounts Are Subject To ChangeFax your order in and qualify for a 3% Discounton Standard orders for all orders which includecomplete part numbers.*Order via Fax (Dealers Only):All customers are welcome to order parts via Fax.Domestic (US) Customers dial:1-800-6-PARTS-7 (800-672-7877)Note: Discounts Are Subject To ChangeOrder via Phone: Domestic (US) Dealers Call:1-800-427-1244Non-Dealer Customers:Contact your local Multiquip Dealer forparts or call 800-427-1244 for help inlocating a dealer near you.International Customers should contacttheir local Multiquip Representatives forParts Ordering information.When ordering parts, please supply: Dealer Account NumberDealer Name and AddressShipping Address (if different than billing address)Return Fax NumberApplicable Model NumberQuantity, Part Number and Description of Each PartNOTE Specify Preferred Method of Shipment: Fed Ex/UPS DHL Priority One Truck Ground Next Day Second/Third DayUnless otherwise indicated by customer, all orders are treated as Standard Orders and will shipwithin 24 hours. We will make every effort to ship Air Shipments the same day the order is received,if received prior to 2PM PST. Stock Orders must be noted on fax or web order form.WE ACCEPT ALL MAJOR CREDIT CARDS!WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06) — PAGE 5
RULES FOR SAFE OPERATION & SAFETY DECALS Do not operate or service this equipmentbefore reading the operating and maintenanceinstructions manual or serious injury mayresult. Do not operate this equipment unless allguards and safety devices are attached andin place. Stop the engine when leaving theequipment. Block the unit when leaving or when usingon a slope Maintain this equipment in a safe operatingcondition at all times. Caution must be exercised while servicingthis equipment. Rotating and moving parts cancause injury if contacted. Stop the engine before servicing, addingfuel and oil. When towing, an adequate safety chainmust be fastened to the frame, refer to page 9. Keep all inexperienced and unauthorizedpeople away from the equipment at all times. Unauthorized equipment modifications willvoid all warranties. Check all fasteners periodically for tightness.Also check towing tongue bolt, lock nut andwheel lug nuts for wear. Wear safety glasses at all times whenworking around machinery. Stop the engine and disconnect the sparkplug before allowing anybody’s hands in themixing drum. Never pour or spray water over the engineor electric motor. Always stand clear of dump handle whenmixer is in operation. Any binding of materialbetween the mixer blades and drum will causedrum and handle to quickly move in thedischarge position.The safety instruction decals shown must be on all Whiteman MixersCAUTION!SHUT OFF ENGINE BEFOREPUTTING HANDS IN MIXING DRUMCaution Decal is:P/N EM948423SAFETY INSTRUCTIONS1. Read owners manuals before operating.2. Keep unauthorized and untrained people away from machine during operation.3. Make sure all safety devices are in place before this machine is started.4. Make sure engine is turned off and spark plug wire is disconnected before cleaning themachine.5. Keep hands and fingers away from moving objects.6. Do not operate machine in an enclosed area. Proper ventilation is required.7. Never leave machine unattended when operating.8. Always stop engine and allow engine to cool before adding fuel or oil.ÑÑ,The safety instruction decal is P/N 924801PAGE 6 — WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06)
WARRANTYThere are no warranties, express or implied, made by MultiquipInc. hereunder on Products manufactured or distributed by itexcept the warranty against defects in material and workmanshipon new Products to the original purchaser, as hereinafter setforth.Multiquip Inc. warrants Products manufactured by it to be freefrom defects in material and workmanship under normal andproper use and servicing for the periods specified on the bottomof this page. Warranty on the engines supplied with the Productsis limited to the warranty extended by the engine manufacturer.Multiquip Inc.’ sole obligation under this warranty is limited to thereplacement or repair, at its Carson, California facility, or suchauthorized facility, of only such part or parts thereof as shallappear to Multiquip Inc. upon inspection at such facility, to havebeen defective in material and workmanship.There are no warranties, express or implied, in addition to theabove except as may be provided in writing by Multiquip Inc.MULTIQUIP INC. SHALL NOT BE LIABLE FOR ANY SPECIAL,INDIRECT OR CONSEQUENTIAL DAMAGES.THE FOREGOING WARRANTIES ARE IN PLACE AND IN LIEUOF ALL WARRANTIES OF MERCHANTABILITY ANDFITNESS AND SETS FORTH THE ENTIRE OBLIGATION OFMULTIQUIP INC.To avoid misrepresentations with respect to Products soldhereunder, the Dealer agrees that no warranties, or otheroperating guaranties on any Products covered by this Agreementshall be made in excess of those made by Multiquip Inc.Multiquip Inc. Warranty Periods:A statement giving model and serial number of the Product, dateof sale to original purchaser and date and description of failureshall accompany all parts.WM-900 . 12 monthsAny part or parts determined by Multiquip Inc. to be defective willbe replaced free of charge, F.O.B. Carson, California. Returnedparts subject to warranty must be shipped prepaid to MultiquipInc. within 30 days from the date the defective part or parts wereremoved. This warranty does not apply to any part or parts whichhave been subject to abuse or unauthorized repairsWarranty with respect to Products, components and accessoriesnot manufactured by Multiquip Inc. is limited to the warrantyextended by the manufacturer of those items.WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06) — PAGE 7
WM-900S, 900P — OPERATIONSRefer to the following chart. For recommend plug sizes.MOTOR115 VOLT 1ØWM 700230 VOLT 1ØWM 900HORSEPOWERPIGTAIL CAP CONN BODYNEMA/NEMA/WHITEMAN WHITEMANPIGTAIL CAP CONN BODYNEMA/NEMA/WHITEMANWHITEMAN1½ & 3 HP L5-30P/940545 L5-30R/940546 L6-15P/940550 L6-15R/940551CONTROLSGENERALKILL SWITCH: (Gasoline Engine Only) Located on the side ofthe engine cover.The Whiteman WM-700 and WM-900 Series plaster and mortarmixers are quality mixers that have a batch capacity of 2.5 and3.5 bags respectively. With proper care, they will give continuousservice year-after-year.ENGINE THROTTLE AND CHOKE CONTROLS: Please referto the engine owners manual for specific instructions. Theelectric motor switch ( electric motor only) located on the motor— is used to start and stop the mixer.BEFORE STARTINGBefore starting the engine, read the engine owners manualand thoroughly understand the safety information.DUMP LATCH: To dump the tub, grasp the dump handle andlift the dump latch, then rotate the tub to discharge the mix.After, discharge, return the tub to the vertical mixing position.Check the items listed below:CLUTCHOil Levels. Be sure to check the oil levels in the engine andengine reduction unit before starting the unit.The paddle shaft and mixing blades are engaged anddisengaged by tightening and loosening the drive belts with aspring loaded idler pulley. To engage the clutch, rotate the levercounterclockwise. The spring maintains the correct belt tension.To disengage the clutch, rotate the lever clockwise against thelever stop. The engine base is slotted to adjust for belt wear andto bring the idler pulley into operating range.Hardware. Check all hardware on the mixer before starting.Periodically inspect all hardware. Loose hardware cancontribute to early component failure and poor performance.Use the torque chart below as a general guideline and keepall hardware tight:CAUTION: Stop the engine before allowing anybody to puttheir hands in the mixing drum.HARDWARE DIATORQUE (LB./FT.)%/16"-1814#/8" -1624WHEEL BEARINGS#/8" - 2437½" - 1339½" - 13 (Grade 8)90After every 3 months of operation, remove the hub dust cap andinspect the wheel bearings. Once a year, or when required,disassemble the wheel hubs remove the old grease and repackthe bearings forcing grease between rollers, cone and cagewith a good grade of high speed wheel bearing grease (neveruse grease heavier than 265 A.S.T.M. penetration (“No. 2.”) Fillthe wheel hub with grease to the inside diameter of the outerraces and also fill the hub grease cap. Reassemble the huband mount the wheel. Then tighten the adjusting nut, at thesame time turn the wheel in both directions, until there is aslight bind to be sure all the bearing surfaces are in contact.Then back-off the adjusting nut !/6 to ¼ turn or to the nearestlocking hole or sufficiently to allow the wheel to rotate freelywithin limits of .001" to .010" end play. Lock the nut at this position.Install the cotter pin and dust cap, and tighten all hardware.GASOLINE ENGINE CAREFor care and operation of the gasoline engine, refer to theengine manufacturer’s operating instructions furnished withthe engine. We recommend draining and refilling the enginecrankcase at least every thirty hours of operation. Check theengine oil level daily.ELECTRIC MOTOR CAREFor lubrication care and operation of the electric motor, refer toyour electric motor instruction booklet furnished with the motor.Protect the electric motor from dust as much as possible andkeep ventilating openings clean. Do not spray water on theelectric motor.PAGE 8 — WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06)
WM-900S, 900P — OPERATIONSBEARING BRACKETGrease the bearing bracket every month.COUNTERSHAFTNOTE: It is critical that the length of chain be properly adjustedto prevent the Draw Bar and front mixer stand fromdropping to the ground (contact) in the event the DrawBar becomes disconnected from the towing vehicle.STEP 1The countershaft rotates on two self-aligned pillow blockbearings. Grease these every 40 hours using grade #1 LithiumBase grease.DRAW BARGEAR ALIGNMENTThe countershaft and driven pinion are mounted on a slottedbase. To align gears, loosen the pillow block mounting bolts andmove them until the necessary alignment has been made.GEAR LUBRICATIONThe surface of the pinion and the bull gearshould be very lightly greased every 250 hours.IMPORTANT! AVOID OVER-GREASING.EXCESS GREASE WILL ACCUMULATECONTAMINATES AND CAUSE PREMATUREWEAR.BOLT & NUTINSERT CHAIN THROUGHTHE HOLESTEP 2DRAW BARIMPORTANT — DRUM HEAD SEAL CAREGrease seals every 40 hours of operation usingany grade #1 lithium base grease. Applygrease until visible inside of mixing tub(overgrease). This will purge seal system ofcontamination.FRAME ANGLEFRAME GUSSETCONNECTOR LINKDRUM GRILLSTEP 3The drum opening is covered by a steel grill that is hinged foreasy cleaning. This grill should be closed at all times when mixeris in use. Do not remove the grill or grill opening bar. Keep thegrill clean by washing it down daily.VEHICLECONNECTOR LINKDRAW BARCAUTION: Stop the engine before allowing anybody to put theirhands in the mixing drum.TOWING — Before towing, check with local and statelaws for proper compliance.The tow bar and chain must be properly attached to the mixerand towing vehicle prior to towing. Refer to the followinginstallation instruction:Step 1. Insert the Draw Bar into the main frame. Secure, utilizingthe ¾" bolt (grade 5) and nylock nut. Tighten to 100 foot pounds.Step 2. Install the chain through the hole located between theframe gusset and frame angle. Loop the chain together and placeunder the Draw Bar. Secure with connector link.Step 3. Extend the chain along the length of the Draw Bar,remove excess chain (slack) and secure to bottom connectorlink. Secure the chain to the towing vehicle, using the connectorlink.REMOVE EXCESSCHAIN (SLACK)BOTTOM CONNECTOR LINKSAFETY CHAIN .P/N 3148CONNECTOR LINK .P/N 01004WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06) — PAGE 9
WM-900S, 900P — OPERATIONSDANGERBEFORE TOWINGThe following is the recommended wiper blade adjustments:1) STEEL DRUM MIXERSSIDE SCRAPERBALL HITCH COUPLER1. Check vehicle hitch, ball, and coupler for signs of wear ordamage. Replace any parts that are worn or damagedbefore towing.2. Use only the 2" ball diameter as indicated on your coupler.Use of any other ball diameter will create an extremelydangerous condition which can result in separation of thecoupler and ball or ball failure.3. Be sure the coupler is secured to the hitch ball and thelock lever is down tight and locked.Recheck tightness again after towing about 50 miles.4. Check that trailer safety chains are properly connected.RECOMMENDED MAINTENANCE1. Smear ball socket and clamp face with chassis grease.Periodically oil pivot points and solutions surfaces ofcoupler with SAE 30 wt. motor oil.2. When parking or storing your trailer. Keep the coupler offthe ground so dirt will not build up in the ball socket.DANGEREND SCRAPER2) POLYETHYLENE DRUM MIXERSIf housing is deformed,replace complete coupler.USE ONLY GENUINEFULTON REPAIR KITS.CLEANING — BLADE ADJUSTMENTSAlways disconnect the spark plug wire before cleaning the insideof the drum.Never pour or spray water over the gasoline engine or electricmotor.For consistent performance, long life and high quality mixing,thoroughly clean the mixer inside and out at the end of eachday’s operation. To prevent lumps of dried mortar from formingand contamination of future batches, do not allow a buildup ofmaterials to form on the blades or anywhere inside the drum.The poly blade should come as close as possible to the surfacewithout touching. If material builds up on the drum, you may usea rubber mallet to dislodge the material without adverse effect tothe drum.IMPORTANT NOTICEEPOXY COMPATIBILITY — There are some expoxies and otherchemicals used in certain applications that are not compatiblewith polyethylene tubs.Since Whiteman Industries cannot control the end user’sapplication of this product, we will not assume responsibility forthe resulting damages when exposed to incompatible chemicals.PAGE 10 — WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06)
WM-900S, 900P — SPECIFICATIONSWM-900S SPECIFICATIONSMODELU.S.(inch)METRICCAPACITY . 9 CUBIC FEET . 248 LITERSBAG CAPACITY . 2½ - 3½ . 2½ - 3½WEIGHT (APPROX.) . 870 LBS. . 395 KG.L X W X H . 71 X 50 X 59 IN. . 180 X 127 X 150 CM.LENGTH W/TOW BAR . 98 IN. . 248 CM.HEIGHT W/DUMP HANDLE . 77 IN. . 195 CM.DISCHARGE HEIGHT . 21 IN. . 53 CM.DRIVE . V-BELT TO GEAR . —DUMP ACTION . MANUAL . —WM-900P SPECIFICATIONSMODELU.S.(inch)METRICCAPACITY . 9 CUBIC FEET . 248 LITERSBAG CAPACITY . 2½ - 3½ . 2½ - 3½WEIGHT (APPROX.) . 870 LBS. . 395 KG.L X W X H . 71 X 50 X 59IN. . 180 X 127 X 150 CM.LENGTH W/TOW BAR . 98 IN. . 248 CM.HEIGHT W/DUMP HANDLE . 77 IN. . 195 CM.DISCHARGE HEIGHT . 21 IN. . 53 CM.DRIVE . V-BELT TO GEAR . —DUMP ACTION . MANUAL . —NOTE: In accordance with our established policy of constant improvement, we reserve the right to amend these specifications at anytime without notice.WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06) — PAGE 11
EXPLANATION OF CODE IN REMARKS COLUMNHow to read the marks and remarks used in this parts book.Section 1: Items Found In the “Remarks” ColumnSerial Numbers-Where indicated, this indicates a serialnumber range (inclusive) where a particular part is used.Model Number-Where indicated, this shows that thecorresponding part is utilized only with this specific modelnumber or model number variant.Section 2: Items Found In the “Remarks” ColumnSerial Numbers-Where indicated, this indicates a serial numberrange (inclusive) where a particular part is used.Model Number-Where indicated, this shows that thecorresponding part is utilized only with this specific model numberor model number variant.Section 3: Items Found In the “Items Number” ColumnAll parts with same symbol in the number column, , #, , %, or , belong to the same assembly or kit.*Note: If more than one of the same reference number is listed,the last one listed indicates newest (or latest) part available.NOTEIf more than one of the same reference number islisted, the last one listed indicates newest (or latest)part available.NOTEThe contents of this catalog aresubject to change without notice.PAGE 12 — WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06)
WM-900S, 900P — SUGGESTED SPARE PARTSWM-900S/PWM-900S/P1 to 3 Units5 UnitsQty. P/NDescription3 . EM505834 . V-BELT3 . 491115 . V-BELT, w/ELECTRIC MOTOR6 . 491010 . LATCH ASSY3 . EM200863 . BLADE KIT STEEL DRUM3 . EM204625 . BLADE KIT POLY DRUM2 . EM902153 . BEARING, DRUM HEAD2 . 3131 . O-RING, DRUM HEAD2 . 3530 . SEAL KIT1 . 3351 . PINION GEARQty. P/NDescription5 . EM505834 . V-BELT5 . 491115 . V-BELT, w/ELECTRIC MOTOR10 . 491010 . LATCH ASSY5 . EM200863 . BLADE KIT STEEL DRUM5 . EM204625 . BLADE KIT POLY DRUM4 . EM902153 . BEARING, DRUM HEAD4 . 3131 . O-RING, DRUM HEAD1 . EM940734 . SWITCH, ON/OFF2 . 3351 . DRIVEN PINON GEAR1 . 509171 . DUMP HANDLE, POLY DRUM1 . EM201537 . DUMP HANDLE, STEEL DRUM4 . 3530 . SEAL KIT2 . 3065 . SEAL, AXLE2 . 3469 . DUST CAP AXLE2 . EM903049 . BEARING CONE UP TO S/N HL600002 . EM903113 . BEARING CONE STARTING S/N JA000002 . EM903012 . BEARING CUPNOTEPart numbers on this SuggestedSpare Parts List may supercede/replace the P/N shown in the textpages of this book.WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06) — PAGE 13
WM-900S, 900P — DRUM HEAD ASSEMBLY2526PAGE 14 — WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06)
WM-900S, 900P — DRUM HEAD ASSEMBLYDRUM HEAD ASSEMBLYNO.PART NO.PART 07720EM9160195028 B816430473131130023291U-BOLT2NUT HEX ½-134U-BOLT INSERT4DUST CAP . 1 . REPLACES 50017BEARING2BRACKET, DUMP BEARING . 2 . S/N 750002 THRU 750179BRACKET, DUMP BEARING . 2 . S/N 750180 & UPGREASE ZERK . 2 . REPLACES 491705COTTER PIN 1/8 X 2. 2 . REPLACES 491690CASTLE NUT . 2 . REPLACES 502246SPACER . 2 . REPLACES 500089O-RING . 2 . REPLACES 491040SEAL . 2 . REPLACES 504749DRUM HEAD, BEARING BOSS . 2 . S/N 750002, THRU 750179REPLACES 500085DRUM HEAD, BEARING BOSS . 2 . S/N 750180 & UPSPRING . 2 . REPLACES 491930THIN SEAL SPACER . 14 . REPLACES 500088SEAL . 4 . REPLACES 500086SEAL URETHANE . 2 . REPLACES 500613SEAL KIT, PADDLE SHAFT . 1 . INCLUDES ITEMS 4943530QTY.REMARKS*WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06) — PAGE 15
WM-900S, 900P — PADDLE SHAFT ASSEMBLYPAGE 16 — WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06)
WM-900S, 900P — PADDLE SHAFT ASSEMBLYPADDLE SHAFT ASSEMBLYNO.PART NO.PART NAME464748495051525354 #55 11507270EM200863EM204625EM203028U-BOLT2NUT ½"-134U-BOLT INSERT4PADDLE SHAFT1PADDLE ARM-TOW END1PADDLE ARM-CENTER1PADDLE ARM-ENGINE END1PADDLE ARM-CENTER1CENTER BACK-UP BLADE4END BACK-UP BLADE2TOP RUBBER BLADE (STEEL) DRUM ONLY4TOP PLASTIC BLADE (POLY) DRUM ONLY4END RUBBER BLADE (STEEL) DRUM ONLY2END PLASTIC BLADE (POLY) DRUM ONLY2BOLT ½-13 X 5-½1LOCK WASHER ½"1HEX NUT ½-131SPACER BULL GEAR1BLADE KIT, (STEEL) DRUM ONLY . 1 .BLADE KIT, (POLY) DRUM ONLY . 1 .HARDWARE KIT, (RUBBER/POLY BLADES) . 1 .****QTY.REMARKSREPLACES EM923638INCLS ITEMS w/ AND MTG. HDWRINCLS ITEMS w/# AND MTG. HDWRINCLUDED IN BLADE KITS*REFER TO PAGES 14 & 15 FOR DRUM HEAD BREAKDOWNWHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06) — PAGE 17
WM-900S — STEEL DRUMSTEEL DRUM109110 111108PAGE 18 — WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06)
WM-900S — STEEL DRUMSTEEL DRUMCOMMON PARTSNO.PART 7421EM507835EM203332EM507484508095508096 PART NAMEQTY.REMARKSDUMP HANDLE1TOWING TONGUE (P. EYE) . 1 . NO LONGER AVAILABLETOWING TONGUE (PIN HOLE) . 1 . CONTACT MQ SALES DEPT./ACCESSORY ITEMTOWING TONGUE (BALL HITCH) . 1 . CONTACT MQ SALES DEPT./ACCESSORY ITEMCAP SCREW . 1 . REPLACES 505067LOCK NUT . 1 . REPLACES 505069MAIN FRAME1CLUTCH LEVER1DUMP LATCH1CLEVIS PIN1DRUM GRILL1GRILL OPEN BAR1DRUM ASSY (STEEL) . 1 . INCLS. ITEMS w/#DRUM & SHAFT ASSY (COMPLETE) (STEEL) . 1 . INCLS. ITEMS w/% AND DRUM HEAD &PADDLE SHAFT ASSY3148SAFETY CHAIN . 1 . REPLACES 13363010045/16" CONNECTOR LINK2ILLUSTRATED ON PAGE 9WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06) — PAGE 19
WM-900P — POLYETHYLENE DRUMPOLYETHYLENEDRUM121 122123124125116126123124PAGE 20 — WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06)
WM-900P — POLYETHYLENE DRUMPOLYETHYLENE DRUMNO.PART NO.PART 690135041987EM969079504943EM969013PLASTIC DRUM (W/O GRATES)1SUPPORT DRUM1STATIONARY GRATE1MOVEABLE GRATE1GRATE OPEN BAR1DUMP HANDLE1DRUM & SHAFT ASSY (COMPLETE) (POLY) . 1 . INCLS ITEMS w/# AND DRUMHEAD & PADDLE SHAFT ASSYHHCS 3/8" NC X 1 ¼" G-57REPLACES 492376LOCK NUT 3/8" NC7REPLACES 492583FHCS ¼" NC X 1" G-58REPLACES 504987LOCK NUT ¼" NC8REPLACES 492581FHCS 3/8" NC X 2" G-512LOCK NUT 3/8" NC12REPLACES 492583QTY.REMARKSWHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06) — PAGE 21
WM-900S, 900P — GAS ENGINES, PULLEYS & CAB ASSEMBLYCAB ASSEMBLYPAGE 22 — WHITEMAN WM-900S, 900P — PARTS & OPERATION MANUAL — REV. #7 (03/17/06)
WM-900S, 900P — GAS ENGINES, PULLEYS & CAB ASSEMBLYGAS ENGINES, PULLEYS & CAB ASSEMBLYCOMMON PARTSNO.PART NO.PART 30641141CAB ASSEMBLYLATCH ASSEMBLY .DRIVE GEAR 16-½ DIA.ROD ENDSPRINGIDLER PULLEYPILLOW BLOCK BEARINGSPRING CLIPDRIVEN PINION GEAR .SWITCH, ON/OFFCOUNTER SHAFTSNAP RINGS .KEYBOLT 3/8 X16 X 3-1/4KEY12 . REPLACES 5047441211211 . REPLACES 500272112 . REPLACES 490957111REMARKSMODEL WM 900 w/HONDANO.PART NO.PART A ENGINE GX240 K1HA 8HP .HONDA ENGINE GX160 5.5HP ENG.DRIVEN PULLEY-LARGEDRIVE PULLEY-5.5 HPDRIVE PULLEY-SMALL 1" BORE 8.0 HPV-BELTTHREADED RODIDLER ARM1 . REPLACES 4932611111211REMARKSMODEL WM 900 w/WISCONSINNO.PART NO.PART 7775EM5
disassemble the wheel hubs remove the old grease and repack the bearings forcing grease between rollers, cone and cage with a good grade of high speed wheel bearing grease (never use grease heavier than 265 A.S.T.M. penetration ("No. 2.") Fill the wheel hub with grease to the inside diameter of the outer races and also fill the hub grease cap.
The Rt. Rev. George N. Hunt The Rev. Frederick K. Jellison The Rev. Dn. Ida R. Johnson The Rev. Michaela Johnson The Rev. Paul S. Koumrian The Rev. Canon Harry E. Krauss * The Rev. H. August Kuehl The Rev. Richard T. Laremore * The Rev. Donald A. Lavallee The Rev. Canon John E. Lawrence The Rev. Dr. Gary C. Lemery * The Rev. Dn. Betsy Lesieur *
Budapest Bank Gold Cards — Automatically 7,800 5,200 11,900 Budapest Bank consumer credit cards (except for Gold Cards) — 3,900 9,900 5,900 15,900 Busin ess cards Embossed business debit and credit cards Automatically 3,900 — 5,900 —
Renault FLUENCE CENík MoToR AUTHENTIQUE LIFE LIMITED INTENS 1,6 16v 115 304 900 319 900 344 900 364 900 Energy dCi 110 - - 404 900 424 900 RENAULT FLUENCE LIMITED oD 294 900 kč* zÁRUkA LET www.renault.cz Sledujte nás na sociálních sítích SPECIÁLNí NAbíDkA NA vybRANÉ SkLADovÉ vozy WWW.RENAULTbEzCEkANI.Cz
no.1 pump 900 rpm 900 rpm no.3 pump 900 rpm 300 rpm 600 rpm 900 rpm no.2 pump 600 rpm 300 rpm 600 rpm 300 rpm 900 rpm 600 rpm 300 rpm 900 rpm 600 rpm 300 rpm 900 rpm 600 rpm 300 rpm no.4 pump solid line gpm broken line hp bsm pump corp. - manufacturing solutions to pumping problems for over 100 years. (2.4) bsm rotary gear pumps
7 607 273 004 CPA 81, amplifier 4x20W 7 620 900 003 7 607 273 005 CPA 121, amplifier 6x20W 7 620 900 025 7 607 006 424 Cable 8m for CCU/CPA 7 620 900 026 Microphones 7 607 006 110 Hand microphone 7 620 900 007 7 607 006 113 Spiralcable for handmicrophone 7 620 900 001 7 607 006 121 Gooseneck microphone with switch (Schwanenhals) 7 620 900 029
Orange DH4X1C-1200 900 lb. 48" x 46" W 1200 105 22 Orange DH4X1C-4000 900 lb. 82" x 45" S 4000 193 22 Orange DH4X1C-4500 900 lb. 84" x 45" S 4500 199 22 Orange DJ4X1C-700 900 lb. 48" x 46" W 700 105 26 Orange DJ4X1C-2000 900 lb. 82" x 41" W 2000 375 26 Orange DJ4X1C-2800 900 lb. 84" x 45
NACE Rev. 1.1 (ISIC Rev. 3) codes are often linked with more than one NACE Rev. 2 (ISIC Rev. 4) code. For example, 323 NACE Rev. 1.1 is linked with 261, 263 and 264 NACE Rev. 2 codes; 261 NACE Rev. 2 is linked with only one part of 311, 312, 313, 321 and 323 NACE Rev. 1.1 codes. Thus, it is not possible to obtain full codes of NACE
1912-1914 Most Rev. Edward Joseph Hanna 1939-1948 Most Rev. Thomas Arthur Connolly 1947-1962 Most Rev. Hugh Aloysius Donohoe 1948-1950 Most Rev. James Thomas O’Dowd 1950-1969 Most Rev. Merlin Joseph Guilfoyle 1637-1969 Most Rev. Mark Joseph Hurley 1967-1979 Most Rev. William Joseph McDonald 1970-1974 Most Rev. Norman Francis McFarland
