Ardwolf A1 Fingerprint Keypad Lock One Touch To Open User Manual

Ardwolf A1 Fingerprint Keypad Lock One touch to open User Manual

Keypad blue light will stay on after unlock and turn off when locked. Red light indicates that system reject or input error. Blue light flash indicates that system is waiting user input. Press to log out system during blue light flash when finish operation or want to start over if make a mistake. You may input any number before or after user code when unlock by code. Ardwolf A1 Quick Programming Guide fig. 12 fig. 13 Installation Option: The lock will stay on vertical position on the door as long as the two mounting screws were tied up in most case. You may put a tapping screw on inside chassis to increase lock stability. 1. Remove two screws in battery compartment. You will see mounting hole under battery compartment. 2. Use 1/8" (3 mm) Drill Bits to drill a hole on door. through mounting hole. 3. Screw tapping screw in. 4. Put battery compartment back. Product return: Please refer installation instruction to remove lock from door, remove levers from lock, and then refer the following diagram to pack lock. Customer Service: Call: (909) 696-2336 E-mail: service@ardwolf.com www.ardwolf.com

fig. 9 fig. 10 fig. 11 Customer Service: Call: (909) 696-2336 E-mail: service@ardwolf.com www.ardwolf.com

Contents 1. Features -----------4 2. Specifications ---5 3. How to scan your fingerprint -----------------------------------5 Continue rotating key clockwise 4. Programming Code -----------------------------------------------5 5. Fingerprint 6 while pushing lever until the lever is pushed in (see fig. 9b). Rotating key range is from 90 to 135 . Rotate the key 6. User Code --7 counter clockwise, back to original position (see fig. 9c). 7. Beep sound management ---------------------------------------8 Take the key out (see fig. 9d). fig. 6 8. Double verification mode ---------------------------------------8 9. Passage mode enabling/disabling ---------------------------8 10. Key unlock ------9 11. Low battery -9 12. Additional power source --------------------------------------9 13. System reset ---9 14. Troubleshooting ------------------------------------------------9 15. Lock installation -----------------------------------------------11 16. Product return 18 fig. 7 ·3· fig. 8

Active sensor area Fingerprint sensor Keypad fig. 2 fig. 3 Ardwolf A1 A1 Five ways to unlock: Fingerprint, User code, Code Fingerprint, Fingerprint Fingerprint or Key. fig. 4 fig. 5

fig. 1 ·5· ·14·

fig. 8 Press to log out system when finish operation or want to start over if make a mistake. ·6·

fig. 4 Press to log out system when finish operation or want to start over if make a mistake. fig. 5 fig. 6 fig. 7 ·7· ·12·

ARDWOLF A1 FINGERPRINT KEYPAD LOCK INSTALLATION INSTRUCTIONS Press to log out system when finish operation or want to start over if make a mistake. Press to log out system when finish operation or want to start over if make a mistake. fig. 1 fig. 2 The beep sound could be turned off or on. After turn off, the beeper still sounds when you press to login and manage user fingerprint or code. Login the system by administrator fingerprint or programming code, press 7 then to turn off, repeat to turn on. fig. 3 ·11· In order to enable this function, at least two fingerprints must be programmed in the system. Login the system by administrator fingerprint or programming code, press 8 then , successful if you hear long beep and blue light, otherwise you will hear short beep and red light. Repeat to disenable the function. ·8·

·9· ·10·

Please refer installation instruction to remove lock from door, remove levers from lock, and then refer the following diagram to pack lock. Installation Option: The lock will stay on vertical position on the door as long as the two mounting screws were tied up in most case. You may put a tapping screw on inside chassis to increase lock stability. 1 .