Introduction To Satellite Communications - Itso.int
Introduction to Satellite Communications Ababacar Gaye Principal Customer Solutions Engineer, Intelsat Africa 1
Contents What is a telecommunications Satellite? Key applications of satellite communications Satellite orbits GEO Satellite launch Satellite frequency allocations Polarization Introduction to satellite link analysis 2
What is a telecommunications satellite? 3
What is a telecommunications satellite? A telecommunications satellite is: A complex machine located in outer space that receives signals from the Earth converts, amplifies and sends them back down to the Earth reaching millions of locations at the same time. A telecommunications satellite comprises: A platform (or bus): propulsion system, fuel tanks, batteries, solar panels, attitude and orbit control functions, etc. A payload: antennas, amplifiers, frequency converters, etc. 4
What is a telecommunications satellite? Diagrammatic representation of a telecommunication satellite The platform is usually standardized by the manufacturer while the communications payload is customized for a given mission 5
Typical Satellite Coverage Coverage areas depend on the satellite type and targeted services IS-905 C-band Zone beams IS-23 C-band Hemi beam IS-14 Ku-band Zone beams 6
Typical Satellite Coverage Intelsat’s next generation EpicNG satellite coverage IS-35e C-band Spot Beams (2017) IS-33e Ku-band Spot beams (2016) 7
Building and launching a telecommunications satellite It takes about 3 years to get a GEO telecom satellite built and launched. Satellite payloads are customized for a given mission. Satellites are heavily tested on the ground in facilities that reproduce the space environment: Mechanical, Thermal, Noise and RF tests Typical cost of a satellite is 150- 250 million Some satellites can cost as much as 500 million. Not including launch services ( 55- 100 million) and insurance. 8
Frequently Asked Questions (1/2) Who invented satellites? Arthur C. Clarke, who went on to be a well-read author of science fiction novels. When were satellites invented? The first satellites were experimented with in the late 1950’s and early 1960’s. Intelsat’s first satellite, which was called ‘Early Bird’, was launched on 6 April 1965. How big is a satellite? (Based on the Intelsat 9 series) Before liftoff it’s, about 4,500 kilograms! Without fuel, it’s about 2,000 kilograms! The body is 5.6 meters and the solar panels are 31 meters wide – more than a 10-story building! How many years can a satellite last? It varies by satellite type. The type of satellites that we own can last over 20 years, but typically their work life is approximately 15 years. 9
Frequently Asked Questions (2/2) How do you fix satellites if they get broken? The satellites send back ‘health check’ information to our engineers all the time. We try to anticipate any problem that could happen, and have pre-developed commands that we can send to the satellite that are essentially computer programs that tell it to perform certain functions, such as firing a booster or changing the angle of a solar panel, so that it can repair itself. How does a satellite get its power? Mostly solar power collected by the solar arrays/panels. We also have batteries on the satellites for the times when the satellite passes through the earths shadow. This is called eclipse. How much power does it take to transmit a signal? The power used to send a communications signal to the Earth from a satellite is about the same as a typical 60W light bulb, just like you have at home. What kinds of people work in the satellite industry? All kinds! Engineers, rocket scientists, sales people, writers, accountants and lawyers. 10
Key applications of satellite communications 11
Key applications of satellite communications Network Services Cell Backhaul Maritime Communications Oil & Gas Aeronautical Disaster Recovery Enterprise DTH Cable Distribution MCPC Platforms Special Events Satellite News Gathering Mobile Video ISR Military Mobility Hosted Payloads End-to-End Communications Embassy Networks Space Situational Awareness Media Services Government Services 12
Satellite orbits 13
Satellite Orbits MEO LEO GEO Type Description Height Signal Visibility / orbit LEO MEO GEO Low Earth Orbit Equatorial or polar orbit Medium Earth Orbit Equatorial or Polar orbit Geostationary Earth Orbit Equatorial orbit 100-500 miles 6000-12000 miles 22,282 miles 15 min 2-4 hrs 24 hrs Advantages Lower launch costs Short round trip signal delay Small path loss Moderate launch cost Small round trip delays Covers as much as 42.2% of the earth's surface Ease of tracking No problems due to doppler Disadvantages Tracking antenna required Shorter life, 5-8 years Encounters radiation belts Tracking antenna required Larger delays Greater path loss than LEO's Large round trip delays Weaker signals on Earth 14
Satellite Orbits – Applications Low Earth Orbit: Earth Observation International Space Station Satellite communications (constellations) Medium Earth Orbit: Navigation: GPS, Galileo, GLONASS, etc Satellite communications (constellations) Geostationary Earth Orbit: Satellite communications Meteorology 15
GEO Satellite Launch 16
GEO Satellite Launch Multiple burns to achieve GEO orbit 17
GEO Satellite Launch Generic Transfer Profile Generic Transfer Orbit Profile 18
Satellite Frequency Allocations 19
Satellite Frequency Allocations Source: European Space Agency 20
Satellite Frequency Allocations C-band Transmit 5.925 - 6.425 GHz (U.S.) 5.625 – 6.425 GHz (I.T.U.) Receive 3.700 - 4.200 GHz (U.S.) 3.400 – 4.200 GHz (I.T.U.) Ku-band Transmit 14.00 - 14.50 GHz (U.S.) 13.75 – 14.50 GHz (I.T.U.) The higher the frequency, the stronger the effect of rain attenuation Receive 11.70 – 12.20 GHz (U.S.) 11.20 – 11.70 GHz (ITU) Ka-band Transmit 27.5 – 30.0 GHz Receive 17.7 – 20.0 GHz 21
Polarization 22
Polarization Electromagnetic waves have an electrical field and a magnetic field which are orthogonal to each other and to the direction of propagation Polarization of a signal is defined by the direction of the electrical field. Polarization can be: Linear: Horizontal (H) or Vertical (V) Circular: Right Hand Circular (RHCP) or Left Hand Circular (RHLP) 23
Linear Polarization The electrical field is wholly in one plane containing the direction of propagation Horizontal: the field lies in a plane parallel to the earth’s surface Vertical: the field lies in a plane perpendicular to the earth’s surface 24
Circular Polarization The electrical field radiates energy in both the horizontal and vertical planes and all planes in between Right-Hand Circular Polarization: The electrical field is rotating clockwise as seen by an observer towards whom the wave is moving Left-Hand Circular Polarization: The electrical field is rotating counterclockwise as seen by an observer towards whom the wave is moving 25
Polarization frequency re-use A satellite can get twice the capacity on the same frequency channels by using opposite polarizations over the same coverage area. E.g. Transponder A using 6,000-6,072 MHz in vertical polarization Transponder B using 6,000-6,072 MHz in horizontal polarization A VSAT can transmit and receive signals in both polarizations, but will be set to operate in one polarization only for a given service. In case of misalignment of polarization between transmitter and receiver, there is cross-pol interference. Cross-pol discrimination (XPD) is defined as the ratio of power transmitted on the correct polarization to the power transmitted on the incorrect polarization. The specified XPD is usually in the range of 20-30 dB for VSATs. 26
Introduction to Satellite Link Analysis 27
Introduction to Satellite Link Analysis Components of a satellite circuit Satellite Antenna BUC LNB Modem The satellite receives the signals, filters them, converts the frequencies then amplifies them for transmission down to the Earth Antenna The antenna transmits/receives and focuses the energy of the signal towards/from the satellite. The LNB amplifies the received signal and converts down its frequency for reception by the modem The BUC amplifies and converts up the signal for transmission by the antenna The modem modulates and demodulates the signal and is connected to other user equipment (router, TV, etc) BUC LNB Modem 28
Introduction to Satellite Link Analysis Simplified digital communications chain: Analog Information Analog-Digital Converter Voice, Video Analog Information Analog-Digital Converter Digital Information Channel Encoder Channel Coded Information 1001010101 1001010101101 Mbps Mbps Digital Information Channel Decoder Demodulated Signal Digital Modulator Modulated Signal Satellite Transmission MHz Digital Demodulator Received Signal 29
Introduction to Satellite Link Analysis Modulation is the process of varying some characteristics of a periodic waveform, called the carrier signal, with a modulating signal that contains information. Carrier signal (no information) Modulating signal (with information) Characteristics that can vary are the amplitude, frequency and phase. Typical modulations used in satellite communications are PSK and QAM. The order of the modulation how many different symbols can be transmitted with it. E.g. Order 2: BPSK Order 4: QPSK, 4-QAM Order 8: 8-PSK, 8-QAM Order 16: 16-PSK, 16QAM Constellation diagram for QPSK 30
Introduction to Satellite Link Analysis Channel coding (FEC: Forward Error Correction) consists of adding redundant bits to the useful information to allow detection and correction of errors caused by the transmission channel. The FEC is usually given as a fraction 𝑁𝑢𝑚𝑏𝑒𝑟 𝑜𝑓 𝑢𝑠𝑒𝑓𝑢𝑙 𝑏𝑖𝑡𝑠 𝑇𝑜𝑡𝑎𝑙 𝑛𝑢𝑚𝑏𝑒𝑟 𝑜𝑓 𝑏𝑖𝑡𝑠 The FEC is usually given with the modulation scheme. E.g.: QPSK 3/4 means that: A QPSK modulation is used (order 4) And for every 3 bits of useful information, 1 redundant bit is added. Said otherwise, 4 bits are required to send 3 bits of information Or 25% of the bits sent are useless from the user point of view (but still necessary to detect and correct errors) 31
Introduction to Satellite Link Analysis On the importance of efficiency From user point of view, the key parameter is Information Rate (IR) (in Mbps or kbps) The required bandwidth in MHz for a given information rate is directly related to the modulation and coding scheme (modcod). The higher the modulation order (2𝑛 ), the less bandwidth is required The higher the FEC ratio, the less bandwidth is required 𝐼𝑅 (1 𝛼) 𝐵𝑊 𝑛 𝐹𝐸𝐶 𝑅𝑆 Other parameters also matter: roll-off factor (α), Reed-Solomon coding (RS) 𝑀𝑏𝑝𝑠 𝑀𝐻𝑧 The efficiency is defined as the ratio : that is the number of Mbps that can be transmitted in a given MHz. The unit is bit per second per Hz (bps/Hz) The higher the efficiency, the more cost-effective a service is. 32
Introduction to Satellite Link Analysis On the importance of efficiency – Examples 2 Mbps link using QPSK-3/4 (order 4 22 ), with 25% roll-off factor and no Reed-Solomon: 4 Required bandwidth is: 2 1 0.25 3 2 1.67 𝑀𝐻𝑧 Efficiency is 1.20 bps/Hz Same 2 Mbps link using 8PSK-3/4 (order 8 23 ), with 25% roll-off factor and no Reed-Solomon: 4 3 Required bandwidth is: 2 1 0.25 3 1.11 𝑀𝐻𝑧 Efficiency is 1.80 bps/Hz /𝑀𝐻𝑧 /𝑀𝑏𝑝𝑠 𝐸𝑓𝑓𝑖𝑐𝑖𝑒𝑛𝑐𝑦 Same 2 Mbps link using 8PSK-7/8 (order 8 23 ), with 25% roll-off factor and no Reed-Solomon: 8 Required bandwidth is: 2 1 0.25 7 3 0.95 𝑀𝐻𝑧 Efficiency is 2.10 bps/Hz 33
Introduction to Satellite Link Analysis The selection of a modcod is constrained by the signal over noise ratio at reception: The higher the modulation order, the higher the signal to noise ratio must be for the modem to be able to demodulate it. Signal over noise ratio is affected by: Link conditions – propagation attenuation and impairments Available power – on ground and on the satellite (PEB) Performance of the satellite Afternoon session will introduce some tradeoffs to be considered Antenna size at reception Capabilities of the modem A satellite link budget analysis will determine what modcod can be used and what are the required bandwidth and power. 34
Introduction to Satellite Link Analysis What is a good efficiency? In general, the higher the efficiency, the better, but Efficiency is not the only parameter to consider Service availability, cost of equipment, network topology, are also key factors Sometimes a lower efficiency is acceptable to reduce required investment or size of equipment. Example: a Direct-To-Home service with small receiving antennas and cheap demodulators will typically have a lower efficiency than a CBH service using large antennas and efficient modems. 35
Introduction to Satellite Link Analysis Summary A signal transmitted by satellite has to be modulated and coded (modcod). The modcod scheme determines the efficiency which tells how many MHz are required to transmit one Mbps. The achievable efficiency is constrained by link conditions, satellite characteristics and available ground equipment. A link budget analysis is required to determine the maximum efficiency. Efficiency can be increased with better ground equipment (antenna, modem, amplifier) tradeoff to be made between investment (CAPEX) and cost of bandwidth (OPEX) 36
the times when the satellite passes through the earths shadow. This is called eclipse. How much power does it take to transmit a signal? The power used to send a communications signal to the Earth from a satellite is about the same as a typical 60W light bulb, just like you have at home. What kinds of people work in the satellite .
Recovery Enterprise Birth of satellite communications 2/11. . This causes slightly different footprints for uplink and downlink . Telemetry, Attitude Control, Commanding, Fuel, Batteries Power System/Thermal System P
Satellite Communications Overview Satellite earth stations form the ground segment of satellite communications. They contain one or more satellite antennas tuned to various frequency bands. Satellites are used for telephony, data, backhaul, broadcast, community antenna television (CATV), in
Communications Industry which is defined as companies that: 1. Build communications satellites. 2. Build communications satellite earth terminals. 3. Provide satellite communications services. The assessment uses the standard analysis tools of Structure, Conduct, and Performance to evaluate the current health of the .
The first satellite was the Moon, of course, but the idea of communications satellites came from Sir Arthur C. Clark in 1945. The Soviets launched the first manmade satellite, Sputnik I, in 1957. The first communications satellite
ITSO on Prestige Bus Monitoring Document Number: 9459-67053 Revision: A Date: 7th December 2010 UNCONTROLLED PRINT - Unless Release Approval Signature present below Date of Release Release Authority Released by Document Control ECN 9459-90046 FTA-FR001-9459-67053.
the satellite output power to the maximum level, additional noise is introduced into the link from satellite to hub. Therefore, an accurate calculation of the SNR for the entire RTN link must consider: 1. the SNR of the terminal-to-satellite link 2. the SNR of the satellite-to-hub link When the output power of the satellite is at a maximum, SNR .
c. Satellite: Internet access provided through satellites orbiting the Earth. Satellite service requires a satellite Internet subscription from an Internet satellite service provider and a satellite dish. Carriers that provide satellite Internet service are DIRECTV, Dish Network, HughesNet, and Wildblue. d.
BIOGRAFÍA ACADÉMICA DE ALFREDO LÓPEZ AUSTIN Enero de 2020 I. DATOS PERSONALES Nacimiento: Ciudad Juárez, Estado de Chihuahua, México, 12 de marzo de 1936. Nacionalidad: mexicano. Estado civil: casado. Investigador emérito de la Universidad Nacional Autónoma de México, por acuerdo del Consejo Universitario, con fecha 21 de junio de 2000. Sistema Nacional de Investigadores. Nivel III .
