Globe Engineering Specification Master List SPECIFICATION REVISION .
REVISED 01-FEB-2023 Globe Engineering Specification Master List SPECIFICATION AAR AAR/QA/C/005 AERONAVALI DE-G2-001 DE-G2-002 DE-G2-006 DE-G2-007 DE-G2-009 DE-G2-011 Q.D. 10.2.7 SFB6-0997 SFT6-1009 AERONCA APS1 REVISION DESCRIPTION 9 Approved Suppliers Requirements/Certification and Traceability Standard C E B D B A ED 5 REV A ED 9 ED 10 Requests of Waiver Issued From Suppliers Quality System Requirements Digital Product Definition Reqs. FAI at the Sub-Contractors Sub-Contractors Quality Plans Supply Delivery Document Turn Over Book First Article Inspection Kit Supply Spec (B767 Special Freighter) Supply Technical Specification (767 Tanker) A A APS44 APS45 APS52 G NC NC Installation of Rivets Fabrication Practices for Forming, Straightening And Fitting Metal Parts Conversion Coating Aluminum Alloys, Modified Process (Alodine 1200) Cleaning and Passivation of Corrosion and Heat Resistant Alloys, Nickel and Nickel Base Alloys CSFS004 Proof Testing of Air Motor, Anti-Ice and Oil Cooler Lines Installation of Threaded Fasteners Quality Requirement for Fusion Welds General Cleaning of Metal Surfaces Installation of Bolts and Nuts Metal-to-Metal Bonding Aluminum - 250 Deg. F. Curing Adhesive System Part and Identification Numbering - 2 Copies Fusion Welding of Aluminum Alloys Dimpling and Countersinking AEROQUIP 56477 NH1004941-10 R B Flange Strap Assy A Quality Requirements Applicable to Subcontractors APS2 APS202 APS224 APS226 APS227 APS228 APS229 APS34 APS36 APS409 D A TDCNs 1462,1557,1588 NC NC NC B TDCN 1624 C G NC AEROSPATIALE PM 06.002 AEROSTRUCTURES HAMBLE LIMITED
QAS 2000 SECT 2 ALOFT AEROARCHITECTS PS-001 PS-002-1 AMERICAN GEN AIRCRAFT PROCESS SPECS (AGAPS) AGAPS1007 AGAPS1012 AGAPS1013 AGAPS1081 AGAPS1201 AIRBUS AIMS0-1-04-003 ISS 8 NOV 2005 Quality Assurance Requirements For Externally Procured Supplies And Services M G Gas Tungsten Arc and Resistance Welding Marking and Labeling Instructions STC-PMA Parts 12 12 Material Callouts Installation, Countersinking, and Dimpling – Mechanical Fasteners Sheet Metal Fabrication Cadmium Plating Heat Treatment of Aluminum Alloys 7 2 6 AIPI09-01-014 ISS 3 Precipitation Hardened Stainless Steel (15-5PH) Aluminum and Aluminum Alloy Wrought Products Plate Final Cleaning of Hydraulic Pipes AIRDROME AP2097 R Sleeve, Flareless Tube Fitting AIR TRACTOR PS132 D Tubing Fabrication, Beading and Flaring K1 Grommet Assembly, 130 Flush Head, .218 Nominal Diameter AIMS03-02-000 ISS 3 ISS 3 ALCOA FASTENING SYSTEMS CA35913 THE ALUMINUM ASSOCIATION Aluminum Standards Data APPLIED MATERIALS 0250-00098 0250-01019 0250-01033 0250-27105 0250-36352 0250-70351 and 2013 Aluminum Standards and Data 8 3 11 Packaging Specifications Cosmetic Inspection Standards & Specifications Engineering Reqmts for Supplier Part Identification 17 12 Minimum Product EHS Requirements Critical Part COC and Product Quality Report Requirements Requirements for Component Cleaning 7
ARCONIC ELS420 EN1182ND M AD Eddie - Spline Pin Protruding Tension Head Eddie-Bolt 2 Nut, Shear, Lightweight H Heat Treatment of Corrosion and Heat Resistant Alloys Heat Treat of Corrosion and Heat Resistant Alloys (Boeing Commercial Airplane Company Programs) ARROWHEAD PRODUCTS APPS-10-M-100 NC APPS-10-M-200 PCN V130 QCI-08-024 NC L Cleaning and Passivating of Corrosion and Heat Resistant Alloys and Nickel-Base Alloys Cleaning and Packaging of Booster Propellant Feed Assemblies (In-Procedures) ULA Atlas V and Vulcan Lines and Joints Manufacturing Vacuum Heat Treat Instruction Identification AUTO-VALVE, INC. 35C150A B Valve Assy, Check B&E PS1801 B Standard Pipe Beads R D Materials List Qualification and Certification of Nondestructive Testing Personnel 2024-T3 AL Sheet and -T351 Plate 6061-O AL Sheet and Plate 6061-T6 AL Sheet and -T651 Plate Conversion Coating of Aluminum Primer and Painting High Solids Epoxy Primer Waterborne Epoxy Primer Manufacturing Quality, Standard for APPS-3-M-100 F B MPS/MPQ-105-450 CARLETON LIFE SUPPORT SYSTEMS PD1635250 PD1635306 SP1638392 SP1638394 SP1638396 SP1638424 SP1638435 SP1638442 SP1638444 ST1637803 A A A A A A NC AE CHERRY AEROSPACE 2L426Y-E CR7771S CLICK BOND CB2000 CB3503 CB3511 C AL 1 4 Lockheed Bulletin #197 1 Lockbolt Pin, Pull Type Alum Alloy 1.0 Pintail 100 Flush Tension Head Titanium Blind Bolt Protruding Head, Titanium Stem Stud, Medium Base, Adhesive Bonded Nutplate, No Lug, High Reuse Nutplate, One Lug, High Reuse
CB9566 4 Nutplate, Miniature, Floating H Polyurethane Application Procedure On Nameplates and Labels Specification Index for Materials, Processes and Finishes Cancelled and Superseded Specification List Heat Treatment of Aluminum, Specification for 2024 Aluminum Sheet and Plate COBHAM PD434008 PUB23854A PUB24230 SP1638418 SP1638562 A NC B NC COLUMBIA HELICOPTERS 04-RDE-0110 G U Process Specification: Methods of Identification Marking Supersession Document - Materials, Processes, And Standards Supersession Document (Boeing to Columbia Helicopters Inc) Process Specification: Fastener Installation Procedures Process Specification: Finish and Process Codes B Computer - Generated Model Data Management K M P AG P J H W G R H N K INACTIVE Heat Treatment of Aluminum Alloys Heat Treatment of Steels Fusion Welding of Aluminum Alloys Finish specification Application of Corrosion Preventive Compound Welding Symbols Fusion Welding of Steel Parts Ident Abrasive Cleaning of Metals Chemical Cleaning of Metals Natural Satin Finish For Metallic Materials Metal Fabrication Practices Replaced by FPS-MFG-00023 Welding Operators Test Plastic Mat: Low Press. Laminated Glass Fiber Material and Parts Substitution Hole Tolerances Hardness and Conductivity Testing, Procedures and Standard Values For Plating Procedures for Cosmetic Parts 3D Model Dimensional Tolerances Standard Practice Specification Applications Acceptable Deviations Between 3D Engineering Definition and Resulting Machined Parts Standard Practice FES H 06-RDE-0311 06-RDE-0621 06-RDE-1111 12-RDE-0204 C DASSAULT - FALCON JET FES103 FES104 FES107 FES108 FES109 FES110 FES111 FES112 FES115 FES116 FES118 FES119 FES120 FES121 FES132 FES149 FES159 FES179 FES193 FES196 FES199 Report 40010 G CB F E W R B CANCELLED B E
WI-00497 D Cosmetic Plated Parts (Acceptance Criteria for) 5 DAVIS ENGINEERING DE-176 2 Davis Part Marking Procedure Marine And Commercial Product Part Marking Procedure for General Aerospace Product Acceptance Limits and Repair Instructions for Defects in Sheetmetal/Tubing Components Cosmetic Inspection Standard DUNCAN AVIATION GDMR101 PQ3429CE WQR-100 11/2/01 19 E General Design Mfg. Reqs. Part Manufacturer Approval Welder Qualification Requirements BF U K CB APP A7(A),A8(D),A9(B), A10(A),A13(A), A14(A),A15(A), A16(NC) W Flange - 20⁰, Coded Sleeve, Flareless Swaged Tube Materials For Machined Parts Welding of Parts, Fittings, Tubing and Assemblies for Aircraft and Missile Service AA D Trademarks, Aeroquip Water Break Test, Procedure for DE-002 DE-144 DE-157 EATON 24538 35235 ACES1170 ACES13 ACES1555 ACES157 ACES16 ACES16P14 ACES1705 ACES20 ACES2192 ACES2249 ACES2600 ACES2687 ACES284 ACES2898 ACES2934 ACES35 ACES70 ACES7085 5 7 Commercially Pure Titanium Sheet Metal Flanges, Fabrication of H Heat Treatment and Related Processes for 300 Series Corrosion Resistant Steels CV Surface Treatment of Metals for Corrosion Resistance. CA Mechanical Cleaning / Mechanical Passivation E Industrial Products Workmanship and Appearance Levels BM Marking Parts, Processes for R Welding, Resistance, Spot Implementation of AMS-W-6858 G Rivets, Solid and Semitubular, Installation of BV Inspection, Fluorescent Penetrant AC Fusion Weldments, Inspection Processes and Acceptance Standards for H Superseded by ACES2934 BF Product ID, Aeroquip Fluid Conveyance P Key Characteristics, Identification and Implementation of AA APP1 rev A APP2 Forming Metal Tubing, Process & Qual. Reqs. rev C APP4 rev A APP5 rev A
ACES7851 ACES7874 ACES7877 ACES7904 AE62905 MCS86845 MCS86847 P.S. 3-2 P.S. 3-40 PS85613 PS85613 Sect VI PS86746 PS86747 PS86766 PSI-ISO-06 QCS06658 QCS3129 QCS85028 QCS85064 QCS85604 QCS85655 EMBRAER 6868 MEP01-004 MEP02-015 MEP08-029 MEP10-033 MEP21-023 NE01-040 NE01-103 NE03-002 NE03-003 NE03-006 NE03-009 NE03-051 NE03-068 NE03-071 L CANCELLED Superseded by ACES2600/ACES2602 Inspection, Fluorescent and Radiography V Acceptance Test of 787 Aircraft NGS and Cactus APP 1 rev V APP Ducts 2 rev AB APP 3 rev B B Chemical Conversion Coating . A ADD1 Coating, Epoxy-Polyamide, Chromate Free, Corrosion Protective, Process Specification For A Sleeve, Fire Resistant C Material Control Specification - Titanium Tube, Seamless and Welded D Welded Inconel 718 Tube Made From AMS5596 P Part Marking NC Tube Forming Inspection and Acceptance AF Welding Process Specification AD Resistance Welding A Tape, Tube Identification, Application of C Insulation Systems on Ducts and Tubes, Fabrication and Assembly of C Primer and Paint, Preparation and Application of P Purchasing AH Penetrant Inspection AV Quality Manual (Eaton Conveyance Systems) AY Calibration Procedure L Identification Marking Methods NC Identification Marking Methods G Ducting Acceptability Limits For Tube Bending, Forming & Straightening August/2015 C QPL rev C J Contractor Tooling Manual Stainless Steel Screen Aluminum Alloy Alclad 2024, Fine Grained - Sheet E J NC P AK RFA TA38-4-23-15 G L Lubricant Oil for Tube Bending Ink for Metallic Parts Identification Alkaline Degreasing for Ultrasonic Cleaning Inks for Marking of Parts Parts - Marking Methods AZ S R Riveting - Drilling, Countersinking and Dimpling Tube Bending - Requirements Metallic Parts - Cutting, Chamfering and Deburring O Bolts and Screws - Drilling, Countersinking and Dimpling for Installation Machined Metallic Details - General Tolerances K Steel Sheet Parts - Minimum Cold Bend Radii Aluminum Alloy Sheet - Minimum Cold Bend Radii
NE03-073 NE03-076 NE03-077 NE03-080 NE04-003 NE05-007 NE06-005 D L E M Dimensioning and Tolerancing Aluminum Parts - Forming and Straightening Drainage - General Requirements Metal Sheet or Extruded Parts General Tolerances D NC L R Tube - Standard Bead End Welding and Brazing Symbols Solid Rivets - Installation Rivet, Solid, 120 Flush Interference Head Requirements for Grip Selection And Installation Blind Fasteners - Installation Nut Plate - Installation Liquid Penetrant Inspection NE06-013 NE06-025 NE06-034 NE07-001 NE07-012 NE07-051 NE15-309 NE40-002 NE40-006 NE40-012 NE40-026 NE40-047 NE40-051 NE40-053 T AA W RFA TA44-4-29-15 AB D I Z X CF I F AA D L NE40-056 NE40-072 NE40-073 NE40-077 NE40-081 NE40-118 Z E S X M AW NE40-143 NE40-175 NE40-213 NE40-235 NE42-027 NE44-001 NE44-006 E B I Q D F Aluminum Alloys Hardness and Conductivity Values Embraer Production Part Approval Process (EPPAP) Joggles In Extruded and Performed Sheet Sections Aluminum and Its Alloys - Solution Heat Treat Aluminum and Its Alloys - Chemical Conversion Coating Metallic Parts - Cleaning Protection of Metallic Surfaces With Anticorrosive Oil. Austenitic Stainless Steel 300 Series - Heat Treatment Precipitation Hardening Corrosion Resistant Steel Heat Treatment Titanium and Its Alloys - Fusion Welding (TIG) GTAW Fusion Welding Process For Carbon Steel, Low Alloy Steel, Corrosion Resistant Steel and Nickel Alloys Shot Peening Resistance Welding - Spot and Seam Equipment for Thermal Processing - Temperature Control and Classification Stainless Steels - Passivation Fluid Line Components - Cleaning and Decontamination Fluid Resistant Epoxy Primer (MEP 10-059 Types I and II) For Internal Metallic and Composite Parts Application Requirements Titanium Parts - Forming and Straightening Steel Parts - Forming and Straightening Finishing of Polished and to be Polished On Bare Aluminum External Parts Parts - Temporary Protection Glass Bead Peening Barrel Finishing
NE90-195 PF05-019 ORIG J P RFA TA54-6-16-15 Laser Cutting Of Metals Superseded by NE40-215 Surfaces for Electrical Bonding - Preparation and Protection AN Material and Process Specifications Index 01/10 Low Temperature Curing High Performance Industrial Heat Resistant Coating FORD AEROSPACE AFS260382 ORIG Glass Bead Peening GAMAH F1009 F1041 F20000 F20000/F21000 F21000 F31300 GW30300 G2J-01 N20000 T2268 N S F F F G A JULY 1992 G E Flange Flange, Aluminum, Heavy Duty Coupling F20000 Flange Series 20 BACF22W Flange F21000 Flange Series 21 F31300 Flange Butt Welded Series 34 Flange - Butt Welded Series 30 Swaging of Gamah Coupling Flanges Nut - Series 20 Coupling Half - Series 20 GKN AEROSPACE DS100 DS104 ISS 5 ISS 5 Protective Finishes Marking of Parts HARTZELL H-S-13 AJ Parts Identification and Marking B (FINAL) CANCELLED without replacement Tooling General Requirements Manual Tooling, Tool Fabrication Manual Superseded by HACI M 5-2 Tooling Control Metallic Material Thickness Substitution List Sheet Metal Practices PF80-241 ERICKSON AIR-CRAIN ES2000 FLAME CONTROL COATINGS 900-SA Series HONDA AIRCRAFT COMPANY, INC. HACI G 5-2-1 HACI G 5-2-3 HACI P 5-2 HJDS-SL002 HJPS-1006 A A (FINAL) A A EO A1,A2,A3, A4, A5 A EO A1,A2 HJPS-1008 HJPS-2003 HJPS-4001 D A Carbon, Alloy, Corrosion and Heat Resisting Steels and Nickel Based Alloys, Forming, Fabrication and Straightening of General Machining Processes Fusion Welding - Aluminum and Aluminum Alloys
HJPS-4004 HJPS-5001 HJPS-6001 HJPS-6002 HJPS-6004 HJPS-6005 HJPS-6007 HJPS-6011 HJPS-6012 HJPS-6016 HJPS-6019 HJPS-6020 HJPS-6035 HJPS-7008 HJPS-8005 HJPS-9002 HJPS-9005 HJPS-9016 HJPS-9020 HJPS-9022 HJPS-9025 HJPS-9030 HJPS-T002 HJPS-T006 HJPS-T012 QAP5.0 HYDRAFLOW 12F63 12F70 14F02 14F03 14F05 14F13 14K03 21F02 LC008 LC009 LC011 LC012 LC021 ORIG EO -1 A G EO G1,G2,G3,G4 M B CANCELLED B Welding of Steels Heat Treating Aluminum Alloys Identification Marking of Parts and Assemblies Sealing Methods and Materials Superseded by HJPS-T006 Passivating Corrosion-Resistant (Stainless) Steel G H Epoxy Primer Application Chemical Conversion Coating of Aluminum Alloys F EO F1 Chromic Acid Anodizing of Aluminum and Aluminum Alloys Stripping of Organic Coatings Cleaning of Aluminum and Aluminum Alloys Solvent Wipe Cleaning Boric Sulfuric Acid Anodizing of Aluminum Alloys Chemical Milling of Metals B H1 EO H2 D B ORIG EO ORG,-1,-2,-3 ORIG E C EO C,C1,C2,C3 D EO D1 ORIG EO -1 B EO B1,B2 C ORIG ORIG EO -1 B ORIG E AMD A,B AA V AL AC T F N AB L L E M W Laser Profiling Installation and Inspection of Blind Rivets Installation of Threaded Fasteners Aircraft Electrical Bonding and Grounding Fabrication of Tubing Systems Cleaning and Pressure Testing of Tubing and Hoses Precision Cleaning of Oxygen Tubes and Components Installation and Inspection of Permalite Tube Fittings Hardness and Conductivity Testing of Metals Fluorescent Penetrant Inspection Radiographic Inspection of Metallic Materials, Parts, and Joints Purchased Items Inspection Plan (PIIP) Flange - 12J63 Series Flexible Coupling Flange - 12J70 Series Flexible Coupling Flange Flange Flange - Welded Type, 14J02 Series Flexible Coupling Flange Body - Single Flange Welded, 14J02 Series Flexible Coupling per AS4736 Flange - Low Profile Flange, Adapter Flange, Adapter Flange Flange Flange
LC138 LC352 LC1063 LC1064 LC1070 LC1072 LC1074 LC1075 LC1076 LC1078 LC1084 LC1085 LC1121 LC1122 LC1142 LC1478 LC1479 LC1619 PS006 G G A A B NC A A B C A B NC NC NC NC NC NC R A PS006-1 TC001 TC036 TC037 TC038 TC040 TC042 TC046 TC047 VC025 Y J M N G L L H D KOREA AEROSPACE IND. (KAI) 85MP0001 A 85MP0306 ORIG ORIG 85MP0308 85MP0314 85MP0317 85MP0411 85MP0415 ORIG ORIG ORIG ORIG Flange Flange Tee Fitting Cross Fitting Tee Fitting Reducer Tee Fitting Tee Fitting Body Boss Fitting Tee Fitting Body Cross Body Tee Body Sleeve Adapter Flange Flange, Reducer Installation Instruction For Mechanical Attachment of Hydraflow Swage Type Fittings To Tubing Installation Instructions for Mechanical Attachment of Hydraflow Swage Type Fittings to Tubing Using a Electric Torque Motor, Addendum to PS006 Washer Body Nut, Type I Ferrule Body, Type II Nut Assembly Flange Threaded Flange Flange, Jump Size Finish Requirements Application of Solid Film Lubricants Marking of Aircraft and Aerospace Ground Equipment Parts Heat Treatment of Steels Metal Removal Procedures and Limitations Penetrant Inspection Hardness and Conductivity Test (Nondestructive Methods for Verifying Heat Treat Condition) MARSHALL DEF STAN 03-2 DS 04-01-033 6 2 CANCELLED Superseded by AMS03-2 and Preparation of Metal Surfaces No supersession Pipe Beading - 'Flexible Connections Cleaning
DS 04-01-040 DS 04-01-089 DS 04-01-101 DS 05-01-001 DS 06-01-001 MMP 05-01-001 MMP 06-01-001 MMP0000 MMP0004 MMP0008 MMP0009 MMP0010 MMP0011 MMP0015 MMP0024 MMP0054 2 2 10 Geometry For The A.G. Belling Of Tube Surface Finish General Manufacturing Tolerances and Allowables 61 OBSOLETE When invoked use MMP 05-01-001 Protective Treatment When invoked use MMP 06-01-001 Identification Marking Protective Treatment Identification Marking General Manufacturing And Design Requirements 23 OBSOLETE 6 5 16 16 3.01 6 4.03 2.01 7 4.01 6 5 OBSOLETE MMP0063 MMP0071 MMP0072 MMP0075 MMP0140 MMP0142 MMP0181 MMP0210 MMP0308 MMP0314 MMP0320 MIDDLE RIVER AIRCRAFT SYSTEMS 608C5510 608C5511 CF34-10 STM CF34-10 STP CF6-80 STM INDEX CF6-80C2 STP INDEX 6 2 OBSOLETE 5 7 15 13 12 2.01 2.01 8 B ORIG Rel. 17 Rel. 9 11/9/2009 9/27/2017 Non-Destructive Testing Fluorescent Penetrant Inspection Non-Destructive Testing Radiographic Inspection Electrical Conductivity Testing - Aluminum Alloys Electrical Conductivity Testing - Aluminum Alloys Pressure Testing of Dry System Pipes Heat Treatment Aluminum and Aluminum Alloys Testing Requirements For Conformation of Satisfactory Heat Treatment Process - Metals Application of Corrosion Inhibiting Compounds When invoked use MMP320 Manual Argon Arc Welding of Aluminum and Aluminum Alloys Final Cleaning of Oxygen, Nitrogen & Water System Pipes and Associated End Fittings Superseded by MMP140 Removal of Surface Finish Pipe Bending Removal of Surface Coatings Application of Chromate conversion Coating By Brush or Swab Application of Chromate Conversion Coatings to Aluminum and Aluminum Alloys By Immersion Application of Integral Fuel Tank Coating Installation of Wiggins and Hydraflow Swaged Couplings Application of Fluid Resistant Epoxy Primer Fusion Welding of Metals GTAW/MAA Sheet Metal Parts - Shop Run Tolerances Aerodynamic Cleanliness Acceptability Limits Material Specification Index for CF34-10 Engineering Process Index for CF34-10 Material Specification Index for CF6-80 Fan Reverser Engineering Process Index for CF6-80C2 Fan Reverser
747-8 STM INDEX 747-8 STP INDEX GE-80C STP INDEX STPB-73030 STPG-55014 STPG-73046 STPM-50074 STPM-73025 STPM-73030 14 13 92 D A D C D A NC STPM-73051 STPM-73058 STPM-75200 MITSUBISHI HEAVY INDUSTRIES 580AS 996AS P1501 C B Material Specification Index for Boeing 747-8 Engineering Process Index for Boeing 747-8 Engineering Process Index for CF6-80C2 Fan Reverser Fastener Installation and Acceptability Limits Welding, Fusion, Steel, Corrosion and Heat Resistant Alloys - Critical Applications Identification Markings Process Specification for Surface Cleaning & Preparation Prior to Bonding & Priming Process Specification for Sheet Metal Parts Fabrication Fastener Installation and Acceptability Limits Process Specification For Bonding of Metallic Components With High Temperature Modified Epoxy Adhesive Film Painting Composite and Metal Parts and Assemblies Process Specification for Controlled Expendable Materials ORIG A H Reinforcing Ring - Bead, Welding Duct Attachment Reinforcement Rings Welding - Spot, Seam - General D Acceptance Test Procedure for Water Tank Orkal Part Number BT100-3-1 L Inspection of Tubes and Tube Assemblies Y Process Control Procedure for Type II and Type VI Passivation Treatments C M Gas Tungsten Arc & Resistance Welding Instructing. For the Surface Treatment and Application of Chrome Conversion coating of Alum. And Alum. Alloys Penetrant inspection Standard Design & Mfg Processes Marking and Labeling - STC PMA Parts Epoxy White, Painting Instructions Cleaning & Priming For Structural Alum Bonding ORKAL ATP-100 PARKER FLUID CONNECTORS P-108-1 PARKER SYSTEMS DIVISION P1090 PATS AIRCRAFT PS-1 PS-13 PS-15 PS-2 PS-2-1 PS-24 PS-29 C A A C A
PS-3 PS-7 TO-767 F K ORIG M Sealing - Fuel Tank, Fastener & Wire Bundle Preparation & Application of Coatings & Primers Installation Of Gamah Tube End Fittings Compilation of Interchangeable Fuel System Parts PMA PRODUCTS, INC. 45.15-1 3 Marking of Replacement Parts PPG AEROSPACE CA8800 Issue 2/15 Buffable Polyurethane Topcoats Ver 02 Ver 10 Ver 07 Ver 06 Procedure: Controlling Corrective and Preventative Actions Procedure: Controlling Nonconforming Product Performing A First Article Inspection Control of CTQ (Critical to Quality) Parts E G K Tube Fabrication Solid and Blind Rivets, Installation of Non-Aqueous Penetrant Inspection Procedure for P Fusion Welding (Click on attachments tab of the PDF to view forms referenced in spec.) Wet Installation of Fasteners and Corrosion Prevention Using Primer and Sealant Painting Requirements, KC46 Centerline Drogue System (CDS) Hose Reel, Process Specification For. . . Installation of Adhesive Bonded Fasteners, Procedure For Roller Swage Bearing, Installation and Retention, Process Specification For Bonding and Grounding Requirements for KC-46 CDS, Process Specification for Corrosion Prevention Using Primer and Sealant for KC-46 CDS, Process Specification for Threaded Pin-Rivet Fasteners, Process Specification For Grading and Control of Parts And Assemblies For Non-Destructive Testing and Inspection Installation of Spiral Retaining Rings Manufacture of FR600-84MDR, Processes and Standards Directory For Solvent Cleaning And Surface Preparation Tube Bending, Process Requirements for Application of Adhesive Backed Labels TO-953 RATIER-FIGEAC PRO-RF-0009 PRO-RF-0020 PRO-RF-0080 PRO-RF-0204 SARGENT FLETCHER INC. MPP-009 PD434001 PD434004 PD434006 PD434011 ORIG H PD434017 PD434019 PD434021 PD434022 PD434023 PD434026 PD434046 PS434047 PD434048 PD434050 PD434055 PD434065 D A D B A ORIG ORIG J A NC NC
C ORIG Pressure Test Requirements For FR600-84MDR Nitrogen, Fuel and Hydraulic Tubes and Hoses Acceptance Test Procedure for Modified MXU-648 POD Outer Rib Assembly, Acceptance Test Procedure For T-6/AT-6 65 Gallon Auxiliary Tank Assembly, Acceptance Test Procedure For Variable Speed Drogue, Acceptance Test Procedure for Composite Springs Finish & Coating for F-2 Fuel Tank Painting Requirements, FR300 Hose Reel Assembly, Process Specification for Process Specification Finishing & Coating F-16 Fuel Tank F-16 Pylon Assembly Finishing & Coating 600 Gallon Tank Assembly Painting Requirements, FR600 Hose Reel Assembly, Process Specification for Finish and Coating, Model 48-000, Process Specification For Identification & Marking Of Aeronautical Equipment, Assemblies Subassemblies And Parts For Use By The Armed Services Inspection Criteria For Flareless Tube Fittings Welding of Aluminum Alloys By Inert Gas Shielded Method Installation Standard Mechanical Attachment of Swage Type Ferrules to Tubing Nital Etch Inspection of Steel Parts Inspection and Control of Chemical Conversion Coating and Painting Standards for Aluminum Fuel Tank Welding Classification of Characteristics, Specification for ST437003 D Manufacturing Quality, Standard For SENIOR AEROSPACE MS-0065 NR Acceptance Criteria For Perforated Metal SIERRACIN/ HARRISON TIB1229 A Acceptance Criteria For Perforated Metal SNOW ENGINEERING PS103 PS120 PS121 PS122 PS132 8/10/2005 3/20/2004 4/11/1989 7/25/1997 7/16/1996 Epoxy Primer and Polyester Urethane Top Coat Welding 4130 Steel Certification of Welders Welding Stainless Steel Fabrication, Beading, Flaring of Tubing PD434070 PD439001 PD439005 PD439022 PD439030 PS4001 PS410 PS421 PS428 PS429 PS432 PS434 B D C B B B G C R B J G C PS518 PS76 PS90 PS93-1039 P99 QCI4015 Report No 95 SP436125 F F C ORIG AC
SPIRIT AEROSYSTEMS 1TD1379T00001-1001 MAA1-10009-1 MAA1-10034-1 MAA1-10041-1 MAA1-10042-2 MAA7-70548-1 G J E M D J NEW MAA7-70701-1 SPS-100340 SPS-106020 SPS-106130 STM-130020-1 STM-130020-11 STM-130030-1 T001-00010-1 TL00443 E D D F D D C OBSOLETE D Burst Pressure Testing for Transport Elements Quality Assurance Standard for Digital Product Definition at Spirit Aero Systems, Inc. Suppliers Supplier Nonconformance Packaging and Shipping Requirements For Spirit Aerosystems, Inc. Suppliers. First Article Inspection Form Completion G280 Wing Alternative Fasteners Weight Management Control Plan for Spirit Aerosystems Aerostructures Business Unit G650 Wing Temporary Protection of Production Materials, Parts, And Assemblies Heat Treatment of Aluminum Alloys Heat Treatment of Titanium and Titanium Alloys Tool Identification Codes Miscellaneous Tool Codes Supplier Tooling Requirements Superseded by 1TD1379T00001-1001 Burst Pressure Testing for Transport Elements Qualification Test Procedure (QTP) For The Wing Anti-Ice System On The GVI Program SUMITOMO ELECTRIC SUMITUBE FE3 SUMIMARK SM60 7/5/2005 7/5/2005 Flexible Fluoroelastomer 2:1 Shrink Ratio (Reference AMS-DTL-23053/13) High Temperature Fluoroelastomer HeatShrinkable Marker Sleeve 2:1 Shrink Ratio TRIUMPH AEROSTRUCTURES (TULSA) AM MAA7-70095-1 TGI MAA7-70334-1 TGI P-7000 TL00442 SPS-100340 SPS-100340 TGI SPS-103070 SPS-103070 TGI F 24-Jan-19 C E.2 A G.1 CANCELLED NEW.1 Superseded by MAA7-70095-1 IAI G280 Wing Program Finish and Process Specification Matrix Superseded by MAA7-70334-1 IAI Weight Management Control Plan Parts Protection Standards: In-House; Offsite; and Supplier Packaging Requirements Acceptance Test Procedure (ATP) for the Wing AntiIce System for the GVI Program Temporary Protection of Production Materials, Parts, and Assemblies Temporary Protection of Production Materials, Parts, and Assemblies Superseded by SPS-103070 TGI Part Marking Part Marking
TRIUMPH THERMAL SYSTEMS EI-100 PS-0160 PS-1331 PS-2080 PS363 PS707 3 12 14 1 14 ORIG SUPP 36 Standing Instructions Identification Marking Fusion Welding Inspection Standard For Surface Imperfections Pickling and Passivation of Stainless, PH Stainless Steels and Stainless Steel Brazements Repair of Stainless Steel Oil Tanks U.S. ARMY MIS26183 WIGGINS 63052 63152 63252 AW624 W902 W903B W903M254A48D W905B W954G109F20 W954G111F32 WIM-III E Missile Specification for Application and control of Organic Finishes AG U F G AA G NC A NC NC B Ferrule Assembly Ferrule Assembly Ferrule Assembly Ferrule, Socket Weld Ferrule Assembly, Electrical Bonding Ferrule Assy Ferrule Assy Body Assembly Flanged Adapter Flanged Adapter Swaging Manual for Flexible Rigid Wig-O-Flex and Min-O-Mal Tube Connectors. C B B B A T Cleaning and Preparation of Metal Surfaces Angle - Equal Leg Extruded Angle - Unequal Leg Extruded Tee - Extruded Castings, Classification and Inspection of Tolerances, Corrosion and Heat-Resistant Steel, Iron Alloy, Titanium, and Titanium Alloys Bars and Wire Tolerances – Corrosion and Heat Treat Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy AMS (Aerospace Material Spec) AMS03-2 AMS10133 AMS10134 AMS10136 AMS2175 AMS2241 G AMS2242 AMS2243 AMS2244 L Tolerances Corrosion & Heat Resist. Steel Tubing D H Tolerances, Titanium and Titanium Alloy Tubing Reaffirmed 2022-05 Chemical Check Analysis Limits Corrosion and Heat-Resistant Steels and Alloys, Maraging and Other HighlyAlloyed Steels, and Iron Alloys Tolerances, Low-Alloy Steel Sheet, Strip, Plate Tolerances – Carbon and Alloy Steel Tubing AMS2248 AMS2252 AMS2253 E F
AMS2262 AMS2263 H F M AMS2355 AMS2404 AMS2460 AMS2471 AMS2486 AMS2491 AMS2606 AMS2607 AMS2610 AMS2615 AMS2631 AMS2634 AMS2644 AMS2658 AMS2665 AMS2700 AMS2750 AMS2759 AMS2759/1 AMS2759/3 AMS2759/4 AMS2759/5 AMS2759/6 AMS2759/8 AMS2759/9 AMS2759/11 AMS2761 AMS2769 AMS2770 AMS2771 AMS2772 AMS2774 AMS2801 J A K E G F E Sep-03 F G C H D H F G G J J D F C B E A NC D R F G G C Tolerances, Nickel, Nickel Alloy and Cobalt Alloy Sheet, Strip and Plate Tolerances, Nickel, Nickel Alloy and Cobalt Alloy Aircraft Tubing Quality Assurance, Sampling and Testing Aluminum Alloys and Magnesium Alloy Wrought Products (Except Forging Stock), and Rolled, or Flash Welded Rings Plating, Electroless Nickel Plating, Chromium Sulfuric Acid Anodize Conversion Coating of Titanium Alloys FluoridePhosphate Type Surface Treatment of Polytetrafluoroethylene Superseded by AMS2610 Superseded by AMS2610 Pressure Testing, Gaseous Media Pressure Pressure Testing, Hydraulic Ultrasonic Inspection - Titanium and Titanium Alloy Bar and Billet Ultrasonic Inspection Thin Wall Metal Tubing Inspection Material, Penetrant Hardness and Conductivity Inspection of Wrought Alum. Alloy Parts Brazing, Silver For Use Up to 400º F (204º C) Passivation of Corrosion Resistant Steels Pyrometry Heat Treat of Steel Parts Heat Treat of Carbon and Low-Alloys Steel Parts Heat Treat Precipitation-Hardening CorrosionResistant Maraging Steel Parts Heat Treatment Austenitic Corrosion-Resistant Steel Parts Heat Treatment Martenistic Corrosion-Resistant Steel Parts Gas Nitriding of Low-Alloy Steel Parts Ion Nitriding Hydrogen Embrittlement Relief (Baking) of Steel Parts Stress Relief of Steel Parts Heat Treatment of Steel Raw Materials Heat Treatment of Parts in a Vacuum Heat Treatment of Wrought Aluminum Alloy Parts Heat Treatment of Aluminum Alloy Castings Heat Treatment of Aluminum Alloy Raw Materials Heat Treatment of Wrought Nickel Alloy and Cobalt Alloy Parts Heat Treatment of Titanium Alloy Parts
B AMS2807 AMS2816 AMS3025 AMS3100 AMS3265 W E E F G AMS3276 AMS3277 AMS3281 AMS3304 AMS3410 AMS3411 AMS3819 K G J K E D K CANCELLED AMS4006 AMS4015 M M AMS4016 AMS4025 AMS4026 AMS4027 AMS4031 AMS4035 N M P K M L AMS4036 R AMS4037 M AMS4045 R AMS4048 Elastomer: Silicone, Rubber (MQ/VMQ) General Purpose 65-75 Durometer Type A Hardness Flux, Silver Brazing Flux, Silver Brazing Hi
Corrosion Protective, Process Specification For AE62905 A Sleeve, Fire Resistant MCS86845 C Material Control Specification - Titanium Tube, Seamless and Welded MCS86847 D Welded Inconel 718 Tube Made From AMS5596 P.S. 3-2 P Part Marking P.S. 3-40 NC Tube Forming Inspection and Acceptance PS85613 AF Welding Process Specification
Water Capacity, Globe Valves d-8 Maximum Steam Capacity, Globe Valves d-10 Temperature Pressure Ratings, Globe Valves d-11 Close-off Pressures, Globe Valves d-12 Flow Coefficients, Ball Valves d-15 selection tables Zone Valves—1/2 to 1-inch d-16 MZ/MT Globe—1/2 to 1-inch d-18 — d-22 Flowrite Globe Valves—1/2 to 2-inch d-23 — d-31
The Globe-Arc’s visor, along with a combination of inner and outer lenses, provides full protection against IR, UV, and visible light. Plus, inner lenses are available in a variety of different shades – DIN 2, DIN 3, and DIN 5. Globe-arc Helmet Globe-Arc Shade 7 0700 000 308 Globe-Arc Shade 10 0700 000 947 Globe-Arc Shade 11 0700 000 943
MASTER OF SOFTWARE ENGINEERING - SCALABLE SYSTEMS MASTER OF SOFTWARE ENGINEERING - EMBEDDED SYSTEMS MASTER OF BUSINESS ADMINISTRATION & MASTER OF SOFTWARE ENGINEERING MASTER OF SOFTWARE ENGINEERING ONLINE Updated: August 2020 Note: The information contained in this graduate handbook focuses on the resources and locations available at the
1. Master of Science in Mechanical Engineering (SMME) 2. Master of Science in Ocean Engineering (SMOE) 3. Master of Science in Naval Architecture and Marine Engineering (SMNAME) 4. Master of Science in Oceanographic Engineering (SMOGE, joint MIT/WHOI degree) 5. Master of Engineering in Manufacturing (MEng) 6. Mechanical Engineer's degree 7.
Master List List 5 /ŭ/ 1. fun 2. pup 3. bus 4. mug 5. tub 6. but Review Words (A-3): 7. six 8. him Star Words: 9. scrub 10. plug List 6 Sight Word List 1. the 2. of 3. a 4. do 5. to 6. you Review Words (A-4): 7. not 8. on Star Words: 9. are 10. they List 7 /ā/ Spelled a-Consonant-e 1. race 2. late 3. rake 4. make 5. gave 6. age Review Words .
HPKB Design Specification Document Data Mining Design Specification Document Non-Traditional Data Design Specification Document HMI Design Specification Document System Integration Design Specification Document 1.4. Software Design Specification Document Development Gui
Universal Serial Bus Revision 3.2 Specification Universal Serial Bus Revision 3.2 Specification. xxxx and xxxx xxxx and xxxx. Uni-versal Serial Bus Specification Universal Serial Bus Revision 3.2 Specification I2C-Bus Specification I2C-Bus Specification Sys-tem Management Bus Specification
TARGET CONSOLIDATION CONTACT GROUP (TCCG) 4 June 2019 - 10:00 to 15:00 held at the premises of the European Central Bank, Sonnemannstraße 20, meeting room MB C2.04, on 2nd floor 1. Introductory Remarks The Chairperson of the Contact Group will welcome the participants and open the meeting introducing the Agenda. Outcome: The Chairperson welcomed the participants and briefly introduced the .
