Tm 10-3930-664-24p Technical Manual Unit, Direct Support And General .
TM 10-3930-664-24P TECHNICAL MANUAL UNIT, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LISTS (INCLUDING DEPOT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LISTS) TRUCK, FORKLIFT, 4,000 LB. CAPACITY, ROUGH TERRAIN, DED, PNEUMATIC TIRE ARMY MODEL MHE-270 (WITHOUT CAB) NSN 3930-01-330-8907 ARMY MODEL MHE-271 (WITH CAB) NSN 3930-01-330-8906 Approved for Public Release; Distribution is Unlimited HEADQUARTERS, DEPARTMENT OF THE ARMY November 1994
TM 10-3930-664-24P TECHNICAL MANUAL HEADQUARTERS DEPARTMENT OF THE ARMY Washington D.C. 10 November 1994 TM 10-3930-664-24P UNIT, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LISTS (INCLUDING DEPOT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST) TRUCK, FORKLIFT, 4, 000 LB. CAPACITY, ROUGH TERRAIN, DED, PNEUMATIC TIRE ARMY MODEL MHE-270 (WITHOUT CAB) NSN 3930-01-330-8907 ARMY MODEL MHE-271 (WITH CAB) NSN 3930-01-330-8906 REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS You can help improve this manual. If you find any mistakes or if you know of a way to improve the procedures, please let us know. Mail your letter, DA Form 2028 (Recommended Changes to Publications and Blank Forms), or DA Form 2028-2 located in back of this manual direct to: Commander, U.S. Army TankAutomotive and Armaments Command, ATTN: AMSTA-MMM Warren, MI 483975000. A reply will be furnished to you. Approved for public release; distribution is unlimited. TABLE OF CONTENTS SECTION I. SECTION II. GROUP 01 INTRODUCTION REPAIR PARTS LIST PAGE 1 1-1 ILLUS FIG ENGINE 0100 - ENGINE ASSEMBLY. 1-1 ENGINE ASSEMBLY AND MOUNTING . 1-1 0101 - CRANKCASE, BLOCK, CYLINDER HEAD . 2-1 CYLINDER BLOCK ASSEMBLY . 2-1 CYLINDER HEAD. 3-1 1 2 3
TM 10-3930-664-24P TABLE OF CONTENTS PAGE 0102 0103 0104 0105 - 0106- 0108 - CRANKSHAFT . 4-1 CRANKSHAFT AND BEARINGS. 4-1 FLYWHEEL ASSEMBLY. 5-1 FLYWHEEL AND HOUSING . 5-1 PISTONS, CONNECTING RODS. 6-1 PISTON AND CONNECTING ROD . 6-1 VALVES, CAMSHAFTS, AND TIMING SYSTEM . 7-1 ROCKER ARMS AND VALVES. 7-1 PUSH ROD COVER. 8-1 FRONT GEAR COVER AND TIMING PIN. 9-1 CAMSHAFT. 10-1 ENGINE LUBRICATION SYSTEM . 11-1 OIL PUMP . 11-1 OIL PAN . 12-1 OIL COOLER AND DIPSTICK ASSEMBLY. 13-1 ENGINE OIL SAMPLING VALVE . 14-1 FITTINGS AND LINES MANIFOLDS . 15-1 EXHAUST AND INTAKE MANIFOLDS. 15-1 ILLUS FIG 4 5 6 7 8 9 10 11 12 13 14 15 GROUP 03 FUEL SYSTEM 0301 0302- 0304 03060309 - 0311 0312 - FUEL INJECTOR . 16-1 FUEL INJECTOR . 16-1 FUEL PUMPS . 17-1 FUEL INJECTION PUMP MOUNTING AND GEAR . 17-1 FUEL INJECTION PUMP GOVERNOR. 18-1 CONTROL ASSEMBLY FUEL INJECTION PUMP HYDRAULIC HEAD. 19-1 AND HOUSING ATTACHMENTS FUEL INJECTION PUMP BODY ASSEMBLY . 20-1 FUEL INJECTION PUMP LINES . 21-1 FUEL TRANSFER PUMP AND LINES . 22-1 AIR CLEANER . 23-1 AIR CLEANER ASSEMBLY AND MOUNT . 23-1 TANKS, LINES, AND FITTINGS. 24-1 FUEL TANK ASSEMBLY AND LINES . 24-1 FUEL FILTERS . 25-1 FUEL FILTERS . 25-1 FUEL/WATER SEPARATOR. 26-1 ENGINE STARTING AIDS . 27-1 ETHER INJECTOR ASSEMBLY. 27-1 ACCELERATOR AND THROTTLE . 28-1 THROTTLE CONTROL CYLINDER AND MOUNTING . 28-1 ACCELERATOR ACTUATOR ASSEMBLY . 29-1 THROTTLE CONTROL RESERVOIR . 30-1 ii 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
TM 10-3930-664-24P TABLE OF CONTENTS PAGE GROUP 04 GROUP 05 EXHAUST SYSTEM 0401 MUFFLER AND PIPES . 31-1 1 COOLING SYSTEM 0501 0502 0503 - 0504 0505 - GROUP 06 ILLUS FIG RADIATOR. 32-1 RADIATOR ASSEMBLY AND MOUNTING . 32-1 DEFLECTORS, SHROUDS . 33-1 RADIATOR BAFFLES AND SHROUD . 33-1 WATER MANIFOLD, THERMOSTATS . 34-1 THERMOSTAT AND HOUSING . 34-1 WATER INLET CONNECTION1. 35-1 WATER PUMP . 36-1 WATERPUMP . 36-1 FAN ASSEMBLY. 37-1 FAN GUARD . 37-1 FAN ASSEMBLY. 38-1 32 33 34 35 36 37 38 ELECTRICAL SYSTEM 0601 - 0603 0607 0608 - 0609 - 0610 0611 - 0612 - ALTERNATOR . 39-1 ALTERNATOR MOUNTING . 39-1 ALTERNATOR . 40-1 STARTING MOTOR. 41-1 STARTER MOTOR . 41-1 INSTRUMENT PANEL . 42-1 INSTRUMENT PANEL . 42-1 MISCELLANEOUS ITEMS . 43-1 SLAVE RECEPTACLE. 43-1 STE/ICE COMPONENTS . 44-1 LIGHTS . 45-1 FLOODLIGHTS . 45-1 HEADLIGHTS . 46-1 BLACKOUT HEADLIGHT AND MOUNTING . 47-1 FRONT COMPOSITE LIGHT AND MOUNTING . 48-1 REAR COMPOSITE LIGHT AND MOUNTING. 49-1 SENDING UNITS AND WARNING SWITCHES . 50-1 SENDING UNITS AND WARNING SWITCHES . 50-1 HORN, SIREN. 51-1 HORN, HORN BUTTON ASSEMBLY. 51-1 AND BACKUP ALARM BATTERIES, STORAGE. 52-1 BATTERIES AND MOUNTING . 52-1 iii 39 40 41 42 43 44 45 46 47 48 49 50 51 52
TM 10-3930-664-24P TABLE OF CONTENTS PAGE 0613 - GROUP 07 CHASSIS WIRING HARNESS. 53-1 DASH WIRING HARNESS (PARTIAL VIEW) . 53-1 DASH WIRING HARNESS (PARTIAL VIEW) . 54-1 MAIN WIRING HARNESS . 55-1 ENGINE WIRING HARNESS . 56-1 STE/ICE WIRING HARNESS . 57-1 CAB WIRING HARNESS . 58-1 TRANSMISSION ILLUS FIG 0705 - 0710 - 0713 - 0714 - 0721 - 0725 - GROUP 09 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 PROPELLER AND PROPELLER SHAFTS 0900 - GROUP 10 TRANSMISSION SHIFTING COMPONENTS . 59-1 TRANSMISSION SHIFTER MOUNTING. 59-1 TRANSMISSION SHIFTER . 60-1 TRANSMISSION ASSEMBLY. 61-1 AXLE DISCONNECT LINKAGE AND MOUNTING . 61-1 TRANSMISSION ASSEMBLY AND MOUNTING . 62-1 TORQUE CONVERTER AND HOUSING. 63-1 TRANSMISSION CASE AND PLATE ASSEMBLY. 64-1 PUMP DRIVE . 65-1 OUTPUT SHAFT AND DISCONNECT ASSEMBLY. 66-1 INTERMEDIATE CLUTCH. 67-1 FORWARD AND REVERSE CLUTCH ASSEMBLY. 67-1 FIRST AND SECOND CLUTCH ASSEMBLY. 68-1 THIRD CLUTCH ASSEMBLY . 69-1 SERVO UNITS . 70-1 MODULATOR VALVE AND INCHING VALVE . 70-1 TRANSMISSION CONTROL VALVES . 71-1 COOLERS, PUMPS, MOTORS . 72-1 CHARGE PUMP AND FILTER ASSEMBLY . 72-1 TRANSMISSION OIL COOLER, LINES AND OIL . 73-1 SAMPLING VALVE IDLER GEARS . 74-1 REVERSE IDLER GEAR ASSEMBLY. 74-1 53 54 55 56 57 58 PROPELLER SHAFTS. 75-1 FRONT DRIVE SHAFT ASSEMBLY. 75-1 REAR DRIVE SHAFT ASSEMBLY . 76-1 75 76 FRONT AXLE 1000 - FRONT AXLE ASSEMBLY . 77-1 FRONT AXLE ASSEMBLY MOUNTING AND LINES. 77-1 FRONT AXLE ASSEMBLY . 78-1 iv 77 78
TM 10-3930-664-24P TABLE OF CONTENTS PAGE 1002 1003 1004 - GROUP 11 1102 1103 1104 - 1204 - 1206 - 81 REAR AXLE ASSEMBLY. 82-1 REAR AXLE ASSEMBLY MOUNTING, VENT LINE . 82-1 AND AXLE ALIGNMENT REAR AXLE ASSEMBLY. 83-1 DIFFERENTIAL. 84-1 REAR AXLE DIFFERENTIAL ASSEMBLY . 84-1 PLANETARY OR FINAL DRIVE . 85-1 REAR AXLE PLANETARY DRIVE ASSEMBLY . 85-1 STEERING MECHANISM . 86-1 REAR AXLE STEERING MECHANISM. 86-1 82 83 84 85 86 SERVICE BRAKES . 87-1 FRONT BRAKE ASSEMBLY . 87-1 REAR BRAKE ASSEMBLY. 88-1 HYDRAULIC BRAKE SYSTEM. 89-1 MASTER CYLINDERS AND SERVICE BRAKE LINES. 89-1 PARK BRAKE CYLINDER MOUNTING. 90-1 AND CONTROL LINE PARK BRAKE CYLINDER . 91-1 MECHANICAL BRAKE SYSTEM. 92-1 SERVICE BRAKE AND INCHING PEDAL. 92-1 87 88 89 90 91 92 WHEELS 1311 1313 - GROUP 14 80 BRAKES 1202 - GROUP 13 79 REAR AXLE 1100 - GROUP 12 DIFFERENTIAL. 79-1 FRONT DIFFERENTIAL ASSEMBLY. 79-1 PLANETARY OR FINAL DRIVE . 80-1 FRONT PLANETARY DRIVE ASSEMBLY . 80-1 STEERING MECHANISM . 81-1 FRONT AXLE STEERING MECHANISM . 81-1 ILLUS FIG WHEEL ASSEMBLY . 93-1 WHEEL ASSEMBLY . 93-1 TIRES. 94-1 TIRES. 94-1 93 94 STEERING 1401 1407 - MECHANICAL STEERING GEAR ASSEMBLY. 95-1 STEERING COLUMN ASSEMBLY. 95-1 POWER STEERING GEAR ASSEMBLY. 96-1 v 95
TM 10-3930-664-24P TABLE OF CONTENTS PAGE 1411 1414- GROUP 15 GROUP 18 ORBITAL STEERING VALVE. 96-1 HOSES, LINES, FITTINGS. 97-1 STEERING HOSES, LINES, AND FITTINGS. 97-1 STEERING SYSTEM VALVES . 98-1 PRIORITY VALVE. 98-1 STEERING SELECTOR VALVE. 99-1 FRAME AND TOWING ATTACHMENTS 1501 FRAME ASSEMBLY . 100-1 CHASSIS. 100-1 1502 COUNTERWEIGHTS . 101-1 COUNTERWEIGHT . 101-1 1503 PINTLES AND TOWING ATTACHMENTS . 102-1 TOW BAR, PINTLE HOOK AND CHAINS. 102-1 ILLUS FIG 96 97 98 99 100 101 102 BODY, CAB, HOOD AND HULL 1801 - 1802 - 1805 - 1806 1808- BODY, CAB, HOOD AND HULL ASSEMBLIES . 103-1 ROLLOVER PROTECTIVE. 103-1 SYSTEM/FALLING OBJECTS PROTECTIVE SYSTEM ASSEMBLY (MODEL MHE-270) ROLLOVER PROTECTIVE. 104-1 SYSTEM/FALLING OBJECTS PROTECTIVE SYSTEM ASSEMBLY (MODEL MHE-271) CAB FRONT COVER ASSEMBLY . 105-1 CAB RIGHT SIDE PANEL ASSEMBLY . 106-1 CAB LEFT SIDE PANEL AND DOOR ASSEMBLY . 107-1 HOOD AND HOOD SUPPORT ASSEMBLY . 108-1 HOOD LATCH ASSEMBLY . 109-1 TRANSMISSION COVERS. 110-1 FENDERS, WINDSHIELD AND GLASS. 111-1 FRONT FENDERS. 111-1 REAR FENDERS . 112-1 CAB WINDSHIELD AND WINDOWS . 113-1 FLOORS AND RELATED COMPONENTS . 114-1 FLOOR PLATE, VALVE BRACKET. 114-1 AND FLOOR MAT UPHOLSTERY SEATS . 115-1 SEAT ASSEMBLY AND SEAT BELTS . 115-1 STOWAGE RACKS AND BOXES . 116-1 TOOL BOX, LIQUID CONTAINER BRACKET . 116-1 ASSEMBLY AND FIRE EXTINGUISHER BRACKET vi 103 104 105 106 107 108 109 110 111 112 113 114 115 116
TM 10-3930-664-24P TABLE OF CONTENTS PAGE GROUP 22 BODY, CHASSIS AND HULL ACCESSORY ITEMS 2202 - 2210- GROUP 24 ILLUS FIG ACCESSORY ITEMS. 117-1 MIRROR ASSEMBLY . 117-1 DEFROSTER FAN ASSEMBLY. 118-1 HEATER ASSEMBLY . 119-1 WINDSHIELD WIPER AND MOUNTING . 120-1 DATA PLATES AND INSTRUCTION HOLDERS . 121-1 DATA PLATES, INSTRUMENT PANEL AND. 121-1 DIRECTIONAL CONTROL VALVE DATA PLATES, HOOD ASSEMBLY, LEFT. 122-1 TRANSMISSION SIDE COVER CHASSIS (LEFT SIDE) AND FLOOR PLATE (LEFT SIDE) DATA PLATES, RIGHT FRONT FENDER . 123-1 RIGHT REAR FENDER ASSEMBLY, RIGHT TRANSMISSION SIDE COVER, AND FLOOR PLATE (RIGHT SIDE) DATA PLATES, ENGINE AND PRIORITY VALVE. 124-1 117 118 119 120 121 122 123 124 HYDRAULIC AND FLUID SYSTEMS 2401 2402- 2403 - 2404 - PUMP AND MOTOR . 125-1 HYDRAULIC PUMP AND PUMP DRIVE . 125-1 MANIFOLD AND/OR CONTROL VALVES . 126-1 DIVERTER VALVE. 126-1 SEQUENCE VALVE. 127-1 DIRECTIONAL CONTROL VALVE AND MOUNTING . 128-1 DIRECTIONAL CONTROL VALVE, END HOUSINGS . 129-1 AND ANTI-VOID ASSEMBLY DIRECTIONAL CONTROL VALVE, RELIEF VALVE. 130-1 DIRECTIONAL CONTROL VALVE. 131-1 ROTATE SECTION DIRECTIONAL CONTROL VALVE. 132-1 LIFT SECTION DIRECTIONAL CONTROL VALVE. 133-1 TILT SECTION DIRECTIONAL CONTROL VALVE. 134-1 SIDESHIFT SECTION PARK BRAKE AND DIFFERENTIAL . 135-1 LOCK SOLENOID VALVE HYDRAULIC CONTROLS . 136-1 DIRECTIONAL CONTROL VALVE LEVERS. 136-1 AND LINKAGE TILT CYLINDERS . 137-1 TILT CYLINDER ASSEMBLY AND MOUNTING . 137-1 vii 125 126 127 128 129 130 131 132 133 134 135 136 137
TM 10-3930-664-24P TABLE OF CONTENTS PAGE 2405 - 2406 - 2408 - GROUP 47 4702 - 151 152 153 154 155 INSTRUMENTS (SPEED AND DISTANCE). 156-1 MECHANICAL TACHOMETER DRIVE . 156-1 GAUGES AND MOUNTING. 157-1 INCLINOMETER AND HYDRAULIC TANK . 157-1 SIGHT GAUGE 156 157 KITS 9401 - GROUP 95 138 139 140 141 142 143 144 145 146 147 148 149 150 GAUGES (NON-ELECTRICAL) AND MEASURING DEVICES 4701 - GROUP 94 MAST COLUMN. 138-1 OUTER RAIL ASSEMBLY AND MOUNTING . 138-1 MAINLIFT CYLINDER. 139-1 INTERMEDIATE RAIL ASSEMBLY . 140-1 DRIVE CHAIN ASSEMBLY. 141-1 INNER RAIL ASSEMBLY. 142-1 FREELIFT CHAIN ASSEMBLY. 143-1 FREELIFT CYLINDER . 144-1 SIDESHIFT CARRIER (FRONT VIEW) . 145-1 SIDESHIFT CARRIER (REAR VIEW) . 146-1 SPINE ASSEMBLY . 147-1 SIDESHIFT CYLINDER ASSEMBLY. 148-1 ROTATE CARRIAGE ASSEMBLY. 149-1 ROTATE CYLINDER . 150-1 FILTERS, LINES, AND FITTINGS . 151-1 HYDRAULIC HOSES AND FITTINGS. 151-1 (PUMP SUPPLY AND MAST CONTROL) HYDRAULIC HOSES, LINES, AND FITTINGS . 152-1 (MAST COLUMN) HYDRAULIC HOSES, LINES AND FITTINGS . 152-1 (CARRIER ASSEMBLY) HYDRAULIC FILTER ASSEMBLY, FITTINGS . 154-1 LINES, AND MOUNTING LIQUID TANKS OR RESERVOIRS . 155-1 HYDRAULIC TANK AND MOUNTING. 155-1 ILLUS FIG KITS AND RELATED PARTS . KITS-1 KITS . KITS-1 KITS-1 GENERAL USE STANDARDIZED PARTS 9501 - BULK MATERIAL .BULK-1 BULK .BULK-1 viii BULK-1
TM 10-3930-664-24P TABLE OF CONTENTS SECTION lIl. GROUP 26 ILLUS FIG SPECIAL TOOLS . 158-1 SPECIAL TOOLS . 158-1 158 SPECIAL TOOLS LIST TOOLS AND TEST EQUIPMENT 2604 - SECTION IV. PAGE CROSS REFERENCE INDEXES NATIONAL STOCK NUMBER INDEX PART NUMBER INDEX FIGURE AND ITEM NUMBER INDEX ix
TM 10-3930-664-24P UNIT DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LISTS (INCLUDING DEPOT MAINTENANCE REPAIR PARTS AND SPECIAL TOOL LISTS) SECTION I. INTRODUCTION 1. Scope This Repair Parts and Special Tools (RPSTL) lists and authorizes spares and repair parts; special tools; special test measurement, and diagnostic equipment (TMDE); and other special support equipment required for performance of Unit, Direct Support, General Support and Depot Maintenance of the Forklift Truck. It authorizes the requisitioning, issue, and disposition of spares, repair parts and special tools as indicated by the source, maintenance and recoverability (SMR) codes. 2. General In addition to Section I. Introduction, this RPSTL is divided into the following sections: a. Section II. Repair Parts List. A list of spares and repair parts authorized by this RPSTL for use in the performance of maintenance. The list also includes parts which must be removed for replacement of the authorized parts. Parts lists are composed of functional groups in ascending alphanumeric sequence, with the parts in each group listed in ascending figure and item number sequence. Bulk materials are listed separately in their own functional group within Section II. Repair parts for repairable tools are also listed in the section. Items listed are shown on the associated illustration(s)/figure(s). b. Section Ill. Special Tools List. A list of special tools, special TMDE, and other special support equipment authorized by this RPSTL (as indicated by Basis of Issue (BOI) information in DESCRIPTION AND USABLE ON CODE column) for the performance of maintenance. c. Section IV. Cross-reference Index A list, in National item identification number (NIIN) sequence, of all National stock numbered items appearing in the listing, followed by a list in alphanumeric sequence of all part numbers appearing in the listings. National stock numbers and part numbers are cross-referenced to each illustration figure and item number appearance. The figure and item number index lists figure and item numbers in alphanumeric sequence and crossreferences NSN, FSCM, and part numbers. 3. Explanation of Columns (Sections II and lIl). a. ITEM NO. (Column (1)). Indicates the number used to identify items called out in the illustration. 1
SECTION I TM 10-3930-664-24P b. SMR CODE (Column (2)). The Source, Maintenance, and Recoverability (SMR) code is a 5-position code containing supply/requisitioning information, maintenance category authorization criteria, and disposition instructions, as shown in the following breakout: * Complete Repair. Maintenance capacity, capability, and authority to perform all corrective maintenance tasks of the "Repair" function in a use/user environment in order to restore serviceability to a failed item. (1) Source Code. The source code tells you how to get an item needed for maintenance, repair, or overhaul of an end item/equipment. Explanations of source codes follows: Code Application/Explanation PA PB PC** PD PE PF PG KD KF KB Stocked items; use the applicable NSN to request/requisition items with these source codes. They are authorized to the category indicated by the code entered in the 3rd position of the SMR code. ** Items codes PC are subject to deterioration. Items with these codes are not to be requested/requisitioned individually. They are part of a kit which is authorized to the maintenance category indicated in the 3rd position of the SMR code. The complete kit must be requisitioned and applied. MO-(Made at UM/AVUM Level) MF-(Made at IDS/AVUM Level) MH-(Made at IGS Level) ML-(Made at Specialized Repair Act (SRA) Items with these codes are not to be requested/requisitioned individually. They must be made from bulk material which is identified by the part number in the DESCRIPTION AND USABLE ON CODE (UOC) column and listed in the Bulk Material group of the repair parts list in this RPSTL. If the item is authorized to you by the 3rd position code of the SMR code, but the source code indicates it is made at a higher level, order the item from the higher level of maintenance. 2
SECTION II. TM 10-3930-664-24P AO-(Assembled by IDS/AVUM Level) AF-(Assembled by IDS/AVIM Level) AH-(Assembled by IGS Category) AL-(Assembled by SRA) Items with these codes are not to be requested/requisitioned. The parts that make up the assembled item must be requisitioned or fabricated and assembled at the level of maintenance indicated by the source code. If the 3rd position code of the SMR code authorizes you to replace the item, but the source code indicates the item is assembled at a higher level, order the item from the higher level of maintenance. XA - Do not requisition an "XA"-coded item. Order its next higher assembly. (Also, refer to the NOTE.) XB - If an "XB" item is not available from salvage, order it using the FSCM and part number given. XC - Installation drawing, diagram, instruction sheet, field service drawing, that is identified by the manufacturer’s part number. XD - Item is not stocked. Order an "XD"-coded item through normal supply channels using the FSCM and part number given, if no NSN is available. NOTE: Cannibalization or controlled exchange, when authorized, may be used as source of supply for items with the above source codes, except for those codes "XA" or those aircraft support items restricted by requirements of AR 700-42. (2) Maintenance Code. Maintenance codes tell you the level(s) of maintenance authorized to USE and REPAIR support items. The maintenance codes are entered in the third and fourth positions of the SMR Code as follows: (a) The maintenance code entered in the third position tells you the lowest maintenance level authorized to remove, replace and use an item. The maintenance code entered in the third position will indicate authorization to one of the following levels of maintenance. Code Application/Explanation C- Crew or operator maintenance done within unit maintenance or aviation unit maintenance. O- Unit maintenance or aviation unit category can remove, replace and use the item. F- Direct support or aviation intermediate level can remove, replace and use the item. H- General support level can remove, replace and use the item. L- Specialized repair activity can remove, replace and use the item. D- Depot level can remove, replace and use the item. (b) The maintenance code entered in the fourth position tells whether or not the item is to be repaired and identifies the lowest maintenance level with the capability to do complete repair (i.e., perform all authorized repair functions.) (NOTE: Some limited repair may be done on the item at a lower level of maintenance, if authorized by the Maintenance Allocation Chart (MAC) and SMR codes.) This position will contain one of the following maintenance codes: 3
SECTION I TM 10-3930-664-24P Code Application/Explanation O- Unit maintenance or Aviation unit is the lowest level that can do complete repair of the item. F- Direct support or aviation intermediate is the lowest level that can do complete repair of the item. H- General support is the lowest level that can do complete repair of the item. L- Specialized repair activity is the lowest le
ARMY MODEL MHE-270 (WITHOUT CAB) NSN 3930-01-330-8907 ARMY MODEL MHE-271 (WITH CAB) NSN 3930-01-330-8906 Approved for Public Release; Distribution is Unlimited HEADQUARTERS, DEPARTMENT OF THE ARMY November 1994. TM 10-3930-664-24P TECHNICAL MANUAL HEADQUARTERS DEPARTMENT OF THE ARMY TM 10-3930-664-24P Washington D.C.
tm 10-3930-673-24p i technical manual headquarters tm 10-3930-673-24p department of the army washington, d.c., 30 september 2005 unit and direct support maintenance
TECHNICAL MANUAL UNIT, DIRECT SUPPORT, AND . 4,000 POUND CAPACITY, SSN M492 HYSTER MODEL E40XL-MIL (NSN 3930-01-223-8437) Approved for public release, distribution is unlimited. HEADQUARTERS, DEPARTMENT OF THE ARMY DECEMBER 1993. TM 10-3930-655-24P TECHNICAL MANUAL HEADQUARTERS . Repair parts for reparable special tools are also listed in this
PNEUMATIC TIRE, MHE 266, HYSTER MODEL H60XL-MIL (NSN 3930-01-172-7892) SUPERSESSION NOTICE: This manual supersedes the repair parts section only for TM 10-3930-658-14&P dated 8 January 1988 CURRENT AS OF 1 OCTOBER 1991 REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS You can help improve the manual. If you find any mistakes, or if you know of a .
maintenance repair parts and special tools lists truck, forklift, electric, solid rubber tires, 4000 lb capacity, 144 in. lift (drexel dynamics model fl-40-ee-5600m) (army model mhe-206) nsn 3930-00-347-6175 tm 10-3930-611-24p, dated 23 november 1992, is changed as follows 1. cover.
Dec 01, 2006 · *tm 10-3930-675-24p i technical manual headquarters tm 10-3930-675-24p department of the army tm 11
tm 10-3930-660-24p i technical manual headquarters tm 10-3930-660-24p department of the army washington, d.c., 1 may 2006 unit, direct support and general support
safety and prevent damage to the forklift truck. ii. TM 10-3930-664-10 MHE-270 MHE-271 (iii blank)/1-0. TM 10-3930-664-10 CHAPTER 1 INTRODUCTION SECTION I. General Information 1-1. SCOPE a. Type of Manual. This manual contains operating
Introductory Music Lesson Plan s r 1: To make students aware that notes have "names" 2: To develop the ability to identify any "natural" note with reference to a piano keyboard
