High Beam/DRL Bulb Inoperative - JustAnswer
T-SB-0044-10 Rev2 January 27, 2010 High Beam/DRL Bulb Inoperative Service Category Vehicle Exterior Section Lighting (ext) Market USA Applicability YEAR(S) MODEL(S) 2008 – 2010 Avalon ADDITIONAL INFORMATION TSB REVISION NOTICE October 13, 2011 Rev2: The entire TSB has been updated. Production Change Information has been removed — TSB applies to ALL 2008 – 2010 model year Avalon vehicles. March 16, 2011 Rev1: Parts Information table has been updated. Any previous printed versions of this service bulletin should be discarded. Introduction On some 2008 – 2010 model year Avalon vehicles, the High Beam/DRL bulb may become inoperative earlier than expected. NOTE Although the High Beam and Daytime Running Light (DRL) operate on the same bulb, the High Beam/DRL light bulbs are separate from the headlights (low beams). This condition does not impact the ability to continue to use regular (low beam) headlights in the event a High Beam/DRL bulb were to become inoperative. 2011 Toyota Motor Sales, USA Page 1 of 5
Rev2 T-SB-0044-10 January 27, 2010 Page 2 of 5 High Beam/DRL Bulb Inoperative Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 BD1123 R & R and Align Both Headlamp Assemblies 1.2 811#0-070#1 72 71 APPLICABLE WARRANTY This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. Please consult the Warranty Policy Bulletin, “POL11-04: Customer Support Program (ZTR): Warranty Enhancement for High Beam/DRL Bulbs on Certain 2008-2010 MY Avalon Vehicles”, for applicability of warranty, as an enhancement of the warranty coverage for High Beam/DRL bulbs is available. Warranty application is limited to occurrence of the specified condition described in this bulletin. Parts Information PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME QTY 81110-07083 Headlamp Assembly RH (HID) 1 81150-07083 Headlamp Assembly LH (HID) 1 81110-07093 Headlamp Assembly RH 1 81150-07093 Headlamp Assembly LH 1 81110-07080 81110-07081 81110-07082 81150-07080 81150-07081 81150-07082 81110-07090 81110-07091 81110-07092 81150-07090 81150-07091 81150-07092 Repair Procedure 1. Confirm the High Beam/DRL bulb is inoperative. If YES – Replace both headlamp assemblies with revised assemblies. Go to step 2. If NO – This TSB does NOT apply. 2011 Toyota Motor Sales, USA
Rev2 T-SB-0044-10 January 27, 2010 Page 3 of 5 High Beam/DRL Bulb Inoperative Repair Procedure (Continued) 2. Verify if the vehicle has updated headlamp assemblies installed using the information below. NOTE FOR FUTURE SERVICE When replacing a High Beam/DRL bulb, verify the correct bulb type and part number is being used. Revised headlamp assemblies (-07083 and -07093) use the HB3 type bulb, part number 90981-13046. Part number 90981-13066 is the proper HIR type bulb for previous headlamp assemblies. Bulb type must match the type specified on the housing it is installed in. Figure 1 illustrates the difference between the HIR type bulb (P/N 90981-13066) and HB3 type bulb (P/N 90981-13046). Note Bulb shape is not always an accurate indicator of bulb type (HIR or HB3.) Check the back or side of the bulb base for type. Figure 1. 2 1 1 HIR Bulb 2 HB3 Bulb NOTE Bulb shape may not always indicate if the bulb is a HIR or HB3 Type. Check the writing on the bulb base for type. 2011 Toyota Motor Sales, USA
Rev2 T-SB-0044-10 January 27, 2010 Page 4 of 5 High Beam/DRL Bulb Inoperative Repair Procedure (Continued) 3. Verify the type of headlamp housing installed by examining the front or back of the housing for “HIR” or “HB3”. The headlamp housing indicates the type of bulb to be used. Figures 2 and 3 show examples of locations of the correct bulb type. Figure 2. Bulb Type Location Figure 3. Bulb Type Location 4. If the indicated bulb type is HB3, the vehicle already has updated Headlamp assemblies and this TSB does not apply. 5. If the headlamp indicates HIR as the bulb type, go to step 6. 2011 Toyota Motor Sales, USA
Rev2 T-SB-0044-10 January 27, 2010 Page 5 of 5 High Beam/DRL Bulb Inoperative Repair Procedure (Continued) 6. Remove the headlamp assemblies. Refer to the Technical Information System (TIS), applicable model and model year Repair Manual: 2008 / 2009 / 2010 Avalon: Vehicle Exterior – Lighting (ext) – “Lighting: Headlight Assembly: Removal” 7. Install the new headlamp assemblies. 2008 / 2009 / 2010 Avalon: Vehicle Exterior – Lighting (ext) – “Lighting: Headlight Assembly: Installation” NOTE Confirm the headlamp assemblies are properly aligned using the appropriate procedure in the Headlight Installation section of the Repair Manual. 8. After repair, confirm proper operation of the headlight system. 2011 Toyota Motor Sales, USA Copyright 2011 - 2017 Service Repair Solutions, Inc.
When replacing a High Beam/DRL bulb, verify the correct bulb type and part number is being used. Revised headlamp assemblies (-07083 and -07093) use the HB3 type bulb, part number 90981-13046. Part number 90981-13066 is the proper HIR type bulb for previous headlamp assemblies. Bulb type must match the type specified on the housing it
1ER-50 Daily Drilling Report DRL-2 DRL-5 DRL-5 1ER-53 Daily Drilling Report DRL-2 DRL-3 DRL-5 Geological Report Well Sketch, Econ Parameters Well Workover Programme(1) Well Workover Programme(2) Well Workover Programme(3) Well Workover Report(1) Well Workover Report(2) 1ER-74ST Daily Drilling Report DRL-2 DRL-3 DRL-5 1ER-77 Daily Drilling Report
DAF XF 106 LED 13g Proiettore manuale con drl LED Man. headl. LED drl 8.94.200.00 Proiettore manuale con drl LED Man. headl. LED drl 8.94.201.00 H7 - H1 - P21W *Ricambio di qualità equivalente Parts of matching quality FIAT DUCATO - JUMPER - BOXER 02 07 Proiettore H1 H7 Headlamp H1
BC1 Page 41 BEAM CLAMP BD1 Page 41 BEAM CLAMP BF1 Page 42 BEAM CLAMP BG1 Page 42 BEAM CLAMP BH1 Page 42 BEAM CLAMP BF2 Page 42 BEAM CLAMP BG2 Page 42 BEAM CLAMP BL FLANGE CLAMP Page 43 GRATE FIX Page 44 BEAM CLAMP GRATING CLIP Page 45 BEAM CLAMP FLOORFIX HT Page 46 FLOORFIX Page
Q-learning algorithm which requires discretization of state and action space, and is known to be slow [13]. Some works use the deep reinforcement learning (DRL) technique which can handle large state spaces. DRL is used to control radiant heating system in an ofce building in [9], while [8] uses DRL for controlling air ow rates. In both works [8,9]
at least weeks. Encouraged by recent successes in applying deep reinforcement learning (DRL) techniques to solve com-plex online control problems, we study if DRL can be used for automatic TO without human-intervention. However, our experiments show that the latency of current DRL systems cannot handle ow-level TO at the scale of current datacen-
standard duty lifting beam. i-beam design w/flame cut bail . page 9-10. hllb. load leveling beam. page 22-23. hdcrb. dual crane rotating beam. page 28. hsdlb. standard duty lifting beam. i-beam design w/pin bail . page 11. htplb. three point lifting beam. page 24. hbslb. basket sling lifting beam. page 12-14. hfplb. four .
the high perveance ion beam efficiently to the lower beam line to be collimated and decelerated; 4. variable beam dimensions can be easily con-figured, and no additional beam line element is needed to extend an ion beam from 300 mm to 450 mm; 5. energy purity with low energy due to efficient neutral particle filtering by deflected beam collimation
“Cost accounting is a quantitative method that accumulates, classifies, summarizes and interprets information for three major purposes: (in) Operational planning and control ;( ii) Special decision; and (iii) Product decision.” -Charles T. Horngren. 2 “Cost accounting is the process of accounting for costs from the point at which the expenditure is incurred of committed to the .
