INSTALLATION GUIDE - Remote Car Starter & Keyless Entry .
Creating AHigher StandardJBS Technologiesproduces the world'smost innovative andreliable car alarms,remote starters,keyless entry systemsand starterimmobilizers.JBS Technologies is notan importing ordistribution company.Our products aredesigned with patentedtechnology andproduced in the UnitedStates with robotics toinsure flawlessperformance and thehighest quality control.INSTALLATION GUIDE OWNER'S GUIDELook for our productsand services on theworld wide web whereyou'll find a highlytrained support staff toprovide assistance toget you on your way toa safer, moreconvenient drivingexperience.JBS Technologies225 Technology WaySteubenville, OH 43952Phone: 740-282-1212Toll Free: 800-878-8007Fax: 740-282-1201www.jbstech.comJBS TECHNOLOGIESCreating A Higher Standard
YOUR WARRANTYThank you for purchasing American madeproducts by JBS Technologies.To order additional transmitters or otheraccessories, visit ourwebsite at wwww.jbstech.com or contactJBS Technologies atthe following address:JBS Technologies225 Technology WaySteubenville, OH 43952FOR TECHNICAL ASSISTANCEHere's how your warranty works:JBS Technologies warrants to the original customer,and the original car a limited lifetime warranty.Within 12 months of purchase, JBS Technologies willrepair or replace, our option, any defective system atno charge. After 12 months from date of purchase,JBS Technologies will, at our option, repair or replacethe system for a 20 shipping and handling fee.Installation, labor, removal and reinstallation are notthe responsibility of JBS Technologies. Registrationmust be completed and sent in within seven (7) daysof purchase in order to validate the warranty. JBSTechnologies makes no warranty against the theft ofa vehicle or its contents. This warranty is not to beconstrued as an insurance policy against loss.www.jbstech.com1-800-878-8007TO ORDER ACCESSORIES, CALL1-800-659-0764DISCLAIMERJBS Technologies disclaims the warranty ofmerchantability and fitness for any particular use. Thisdisclaimer shall be effective as to all claims of anykind made by or through any wholesaler, retailer,consumer or any other person or entity. Some statesdo not permit the disclaimer of implied warranties insome sales. Hence, this disclaimer may not apply toyou.LIMITATION OF REMEDIESConsumer's remedy is limited to repair or replacementof the unit, and in no event shall exceed the purchaseprice. Incidental, consequential an/or indirect damagesare expressly disclaimed. NO person or entity isauthorized to alter, amend or increase this limitedwarranty.
WARRANTY VALIDATIONCONTENTSPLEASE FILL OUT THIS FORMAND MAIL IT IN TO REGISTER YOUR WARRANTYSystem Features .4Your NameSystem Components.5AddressRequired Tools .5Technical Assistance .55-6Dealer NamePrecautions .6AddressTesting Your Wires.7Date of Purchase / / Model #Make/Model of CarYear of CarV.I.N. #Final Quality Check ByMail to: JBS Technologies225 Technology Way Steubenville, OH 43952PROGRAMMING FUNCTIONSFOR YOUR WALLET OR GLOVE BOXATTENTION:We urge you to immediately place this card in your wallet.Adding Additional Remotes Press and hold brake. Next, press and hold Button#1 on the working remote until the parking lights flash once. Release.Press and release Button #4 on the new remote. The parking lights willflash three (3) times confirming that the new remote was learned. ColdStart On and Off (Degree Select) Press and hold brake. Press and holdButton #2 until the parking lights flash twice. Release. Press and holdButton #2. Each parking light flash is a progression in degrees. Flash#1 is -40ºF, flash #2 is -30ºF, flash #3 is -20ºF, flash #4 is -10ºF, flash#5 is 0ºF, flash #6 is 10ºF, flash #7 is 20ºF. Two quick parking lightflashes is Cold Start Off. Release the brake, the parking lights will flashthree (3) times. NOTE: Factory setting is OFF. Tach Mode - ONPress and hold brake. Press and hold Button #3, the parking lights will flashthree (3) times. Release. Press and release Button #4, the parking lightswill flash twice. The Tach Start is programmed ON. Release the brake, theparking lights will flash three (3) times. Tachless Mode - ON Press andhold brake. Press and hold Button #3, the parking lights will flash three(3) times. Release. Press and release Button #4, the parking lights will flashonce. The Tachless Start is programmed ON. NOTE: Factory setting is TachlessStart ON. Release the brake, the parking lights will flash three (3)times.Programming Runtime with Brake not Pressed Press and hold Button #4.The parking lights will flash once for every five (5) minutes you want toprogram. Release button at desired runtime. Maximum length, 15 minutes.26Making Connections .Locating & Making Connections .7-89-11Neutral Safety Switch .12Connecting 18-Pin Harness.13Connecting 4-Relay Harness.13Antenna Placement.14Anti-Theft System.14Optional Connections .15-18Operator Programming Instructions.18-19How to use Your Remote Transmitter .Vehicle Anti-Theft Chart.FCC ID Notice .Important Functions .2021-242425-26Warranty Validation .26Your Warranty .27Protected by one or moreof the following patents:Patent #08528768PatentPatent #55459447PatentPatent #60087174PatentPatent #5886622PatentOther patents pending.RS700Before You Begin.#5477090#5677664#60097821#59429883REMOTE CONTROL STARTEREmail Address
SYSTEM FEATURESFour-ButtonExtended RangeRemote ControlRemotely start your car to run the heater or airconditioning from an extended distance.Keyless EntryRemotely locks and unlocks your power door locks.Trunk ReleaseRemotely opens your trunk with a push of abutton. (Optional part #775 required)Remote ProgrammableRun TimeRemotely program your vehicle to run 5 to 15minutes.Run TimeConfirmationLets you check the run time that the unit isprogrammed for.Tach/TachlessOptionA programmable feature that lets you choose from theeasy to install tachless operation or the standardwire-in, tach operation.Parking LightConfirmationConfirms that your vehicle has received a remotesignal and will remain on if the engine is remotelystarted.Dome LightSupervisioncomeNever walk up to a dark vehicle again. When unlockingthe vehicles doors by remote control the dome lightwillon and stay on for 1 minute, or until you activate the ignitionswitch. (Optional part #775 required)Cold StartRemotely program your car to start at a presettemperature. Automatically starts your car in freezingtemperature so you never have a dead battery.Pit Stop ModeAllows you to exit the vehicle while the engineremains running.Extended RangeAntennaAllows you to operate your system from up to 400 feetaway. (800 feet for E Models)Code LearningAllows your remote starter to learn new remotes,should you want to add remotes, or if remotes are lost.Limited LifetimeWarrantyGuarantees life-long protection.41-800-878-8007www.jbstech.comMADE IN AMERICA, GUARANTEED FOREVEROPERATING FUNCTIONSFOR YOUR WALLET OR GLOVE BOXATTENTION:We urge you to immediately place this card in your wallet.Starting with the Remote Transmitter Press and release button #1. The parking lightswill flash once, confirming the car starter received the signal. The car will then startand the parking lights will remain on while the vehicle is running. To shut off theengine before the preset time, press button #4 or press the brake pedal. NOTE: If yourcar does not start on the first crank it will automatically attempt to start 2 moretimes (in tachless mode). While in tachless mode, parking lights will wait approximately10 seconds before turning on. Pit Stop: Exiting the Car with the Engine Running Makesure the transmission is in park and press button #1 before turning the ignition switchoff. Keyless Entry Operation Press button #2, the parking lights will flash once andthe doors will lock. Press button #2 again, the parking lights will flash twice, thedoors will unlock, and the parking lights will remain on for one minute or until youturn the ignition on or press the brake. Dome Light Option (optional) The dome lightwill remain on for one minute or until you turn the ignition on or press the brake.Trunk Release Output Optional output modules are available to do one of the following:open the trunk, roll up the windows, close the sun roof etc. This output will pulse.75 seconds when pressed and released. In instances where a continuous signal is neededsuch as sun roof and power windows, hold down button #3 as long as the signal is needed.The parking lights will remain on as long as this button is being pressed. RuntimeConfirmation Press and release Button #4. The parking lights will begin to flash. Each flash equals5 mnutes of runtime.25
VEHICLES WITH FACTORYANTI-THEFT SYSTEMS OLKSWAGONVOLVOMake/ YearBONNIEVILLE 89 FIREBIRD 88 GRAND AM 96-98GRAND AM 99 GRAND PRIX 92-96MONTANA 99 SUNFIRE 96-99SUNFIRE 2000 ALL 97 ALL 97 ALL 97 2000 AVALON 98 CAMRY 98 LAND CRUISER 98 SOLARIA 99 SUPRA 98 BEETLE 98 GOLF 98 PASSAT 98 ALL 98 Anti-theftVATSVATSPASSLOCK 1PASSLOCK 2VATSTRANSPONDERPASSLOCK 1PASSLOCK SPONDERTRANSPONDERTRANSPONDERTRANSPONDERSYSTEM COMPONENTSYour system includes:1-Installation & Operation Guide1-Main Control Module1-Four Button Remote Transmitterwith Slide Protector1-(4) Relay Harness with Relays1-18-Pin Wire Harness1-Hood Pin Switch1-Extended Range Antenna (E Models Only)2-Window Clips(E Models Only)1-Warranty1-Warning Stickerfor Under the Hood2-Bulldog Window DecalsREQUIRED TOOLSYou will need a computer-friendly test lightdrill bit when mounting the hood pin switch.no additional tools are required, however ifyour dash on the driver’s side will come offit. In this case a screwdriver or socket setand a 5/16 inchIn most casesthe bottom ofyou must removemay be needed.TECHNICAL ASSISTANCEShould you need help. First check our website at www.jbstech.com or callour toll-free Tech Support Hotline Monday through Friday 9AM-8PM andSaturday 10AM-4PM EST at 800-878-8007.You must give the following information: Name Telephone Number with Area Code (Fax number if applicable) Year, Make, and Model of the vehicle The model number of the system you are installing The type of assistance you are requestingIf you give the above information you will be called back as soon aspossible, usually within 10 minutes.BEFORE YOU BEGINFCC ID: J3STXJS1194This device complies with part 15 of the FCC Rules,Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received,including interference that may cause undesired operation.24Congratulations, you have purchased one of the most advancedremote starter systems ever made. Your new remote starter isa technological breakthrough utilizing the most advanced, stateof-the-art technology and components. It is computer controlledand manufactured in the U.S.A. The dependability and varietyof features make Bulldog Security the leader in the industry.Enjoy your new remote starter for years to come!This remote system is designed to start your vehicle by sendinga command signal from the remote transmitter or by programmingautomatic temperature or timed start. It is required that yourinstallation be done in a well-ventilated area. It is theresponsibility of the owner to ensure that the remote systemis not used to start the vehicle in an undesired location.5
BEFORE YOU BEGIN cont.It is recommended that a carbon monoxide detector be installedin the living area near the location where the vehicle may begaraged.VEHICLES WITH FACTORYANTI-THEFT SYSTEMS (CONT.)ManufacturerSince there are many different makes and models of vehicles,look at the wiring chart on our website, www.jbstech.com.Read this manual thoroughly before starting the installation.You must also decide if any options are desired such as trunkrelease and dome light supervision. An optional relay will beneeded for these options. Please do not skip any steps.TACH/TACHLESS OPERATIONIn most cases the decision to go with tachless mode will savetime during the installation. If your vehicle is hard-startingthen you should use tach mode.HONDAMAKE SURE YOU PLACE THE WARNING STICKER UNDER THE HOOD.INIFINITYPRECAUTIONSThis system is designed for use with vehicle equipped with fuelinjected, gasoline engines having automatic transmissions only.SAFETY FIRST!Never remotely start your vehicle indoors, with the keys in theignition or unless the transmission is in park. A periodic safetycheck is recommended to ensure that your system is in proper workingorder.DO NOT use mechanical wiring connections, such as crimp or snaptogether taps. Follow instructions on page 7-8.DO NOT disconnect the battery if the vehicle has an anti-theft-codedradio or is equipped with an airbag. Doing so may cause a warninglight to be displayed and may require a trip to the dealer to becorrected.DO NOT leave the interior or exterior lights on for an extended periodof time as it may cause battery drain. Remove the dome light fusefrom the vehicle’s fuse box. NOTE: Starter systems do not work wellwith a partially discharged battery.JAGUARJEEPWRANGLER 99 LEXUSLINCOLNLINCOLNMERCEDESMERCURYDO NOT mount the control module until all connections have beenmade and tested. Use wire ties or double sided tape. MOUNT THEMODULE UNDER THE DRIVER’S DASH.PLEASE USE CAUTION: DO NOT CUT, PROBE OR DISCONNECT THE VEHICLE’S AIRBAG WIRES. THESE WIRESWILL ALMOST ALWAYS BE INSIDE A BRIGHT YELLOWTUBE LOCATED NEAR THE STEERING COLUMN HARNESS.WARNING!GENERAL MOTORS REAR WHEEL DRIVE VEHICLES AND DODGE DAKOTASAll General Motors rear wheel drive vehicles and Dodge Dakotasbuilt prior to 1996 do not have an electrical neutral safetyswitch. They have a mechanical neutral safety switch. The mechanicalneutral safety switch operates as follows.a) The key will only turn to the start position when thegear selector is in park or neutral.b) The key can only be removed from the ignition switchwhen the gear selector is in the park position.You must use special precautions with this system. For more6 information see page 12.Make/ YearSIERRA 98 SONOMA 98 SUBURBAN 98 YUKON 98 YUKON XL 2000 ACCORD 98 ODYSSEY 98 PRELUDE 98 S2000I30 98 Q45 98 QX4 98 ALL 98 GRAND CHEROKEE 99 ALL 97 CONTINENTAL 97 LS 2000 MARK V3 97 NAVIGATOR 97 TOWN CAR 97 ALL 97 COUGAR 99 MOUNTAINEER 98 MYSTIQUE 97 NISSANOLDSMOBILESABLE 96 MAXIMA 98 ACHIEVA 95 ALERO 99 AURORA 95 BRAVADA 98 CUTLASS 97 NINETY-EIGHTSILHOUETTE 99 Anti-theftPASSLOCK 2PASSLOCK 2PASSLOCK 2PASSLOCK 2PASSLOCK (GREY KEY ONLY)TRANSPONDER(GREY KEY ASSLOCK 1PASSLOCK 2VATSPASSLOCK 2PASSLOCK 2VATSTRANSPONDER23
VEHICLES WITH FACTORYANTI-THEFT SYSTEMSManufacturerCHRYSLERMake/ YearMALIBU 97 MONTE CARLO 96-99MONTE CARLO 2000 FULL-SIZE PU 98 S-10 98 SAVANNAH 98 SUBURBAN 98 TAHOE 98 VAN 98 VENTURE 99 CONCORD 98 LHS 98 SEBRING CONTV. 98 DODGE300M 99 INTERPID 98 NEON 2000 FORDGMC22CONTOUR 97 CROWN VIC 98 EXCURSION 2000 EXPEDITION 97 EXPLORER 97 FOCUS 2000 MUSTANG 98 F150/250 98 RANGER 99 TAURUS 96 WINDSTAR 2000 DENALI 99 ENVOY 99 S-15 JIMMY 98 SAFARI 98 Anti-theftPASSLOCK 2VATSPASSLOCK 2PASSLOCK 2PASSLOCK 2PASSLOCK 2PASSLOCK 2PASSLOCK 2PASSLOCK 2TRANSPONDERTRANSPONDER(GREY KEY ONLY)TRANSPONDER(GREY KEY ONLY)TRANSPONDER(GREY KEY ONLY)TRANSPONDER(GREY KEY ONLY)TRANSPONDER(GREY KEY ONLY)TRANSPONDER(GREY KEY RANSPONDERTRANSPONDERTRANSPONDERPASSLOCK 2PASSLOCK 2PASSLOCK 2PASSLOCK 2TESTING YOUR WIRESWhen testing for a positive or negative voltage, you mustuse a computer-friendly test light (logic probe) or a volt/ohmmeter. Make sure to probe and test each wire before makingyour connections.MAKING CONNECTIONSNOTE: If it is necessary to cut a factory wire to make aconnection, see diagram on page 8.1. Strip back two inches of insulation on the wire from theremote starter.Two Inches of Bare Wire2. Strip back one inch of insulation on the wire you needto connect to.One Inch of Bare Wire3. Separate the vehicle wire as shown. Make the separationlarge enough to fit the other wire through.4. Insert the wire(s) from the starter through the hole asshown. if two or more wires are inserted, wrap them inopposite directions.5. Wrap the wire around one side then the other and finallyaround itself as shown.1236. Use electrical tape to wrap. Be sure to cover the wireabout two inches on either side of the connection. Firstpull the wire that you have just connected along side thewire you connected to, tape and wire tie them together.Use this method for all connections.Wire TieCAUTION:Electrical TapeAll wires must be wrapped with tapeand wire tied.7
MAKING CONNECTIONS cont.MAKING END TO END CONNECTIONSFOLLOW THESE INSTRUCTIONSVEHICLES WITH FACTORYANTI-THEFT SYSTEMSManufacturerAcura1. When tying two separate wires together at their ends,strip back one inchof insulation on both wires andseparate the strands of wire as shown below.AUDI2. Twist upper wires together, twist lower wires togetheras shown.3. Lay upper twisted pair of wires over right wire as shown.Bring lower twisted pair of wires up to meet the leftwire as shown.4. Use electrical tape to wrap, be sure to cover about 2inches on either side of connection. Secure with wire tiesas shown.Electrical TapeWire TieWire TieUse this method ONLY when connecting two separate wires endto end.8BMWBUICKCADILLACCHEVROLETMake/ YearTL 99 CL 98 RL 99 INTEGRA 00 NSXA4 00 A6 00 A8 98 ALL 97 CENTURY 97 LESABRE 90-96, 2000PARK AVE 91-96PARK AVE 97 REGAL 93-96RIVIERA 93-99ROADMASTER 93-96SKYLARK 96-98ALLANTE 91-93BROUGHAM 90-96CATERA 98 DEVILLE 92-96DEVILLE 99 ELDORADO 89-98ELDORADO 99 ESCALADE 99 FLEETWOOD 90-96SEVILLE 90-98SEVILLE 99 SLS/ STS 97 ASTRO 98 BLAZER 98 CAMARO 86 CAVALIER 95-99CAVALIER 2000 CORVETTE 88 EXPRESS 98 IMPALA 2000 LUMINA 96 ANSPONDERVATSVATSVATSTRANSPONDERVATS (Some)VATS (Some)VATSPASSLOCK K 2VATSVATSTRANSPONDERTRANSPONDERPASSLOCK 2PASSLOCK 2VATSPASSLOCK 1PASSLOCK 2VATSPASSLOCK 2PASSLOCK 2VATS21
HOW TO USE YOUR REMOTE TRANSMITTERStartBUTTON #1Starts your vehicle from 400 feet away.(E-Model, up to 800 feet)LockUnlockBUTTON #2Locks and unlocks your power door locks.TrunkBUTTON #3Pops your trunkStopBUTTON #4Shuts engine off and programs runtime.Starting the Vehicle with the Remote TransmitterPress and release button #1 (start). The parking lights will flash once,confirming the car starter received the signal. The car will then startand the parking lights will turn on and remain on while the vehicle isrunning. To shut off the engine before the preset time, press button #4(stop) or press the brake pedal. NOTE: If your car does not start on thefirst crank it will automatically attempt to start up to 2 more times.(only in tachless mode) In tachless mode, parking lights will waitapproximately 10 seconds before turning on.Pit Stop: Exiting the Car with the Engine RunningMake sure the transmission is in park and press button #1 (start) beforeturning the ignition switch off. (The engine will remain running for thepreset time.)Keyless Entry OperationPress button #2 (lock/unlock), the parking lights will flash once andthe doors will loc
remote starter systems ever made. Your new remote starter is a technological breakthrough utilizing the most advanced, state-of-the-art technology and components. It is computer controlled and manufactured in the U.S.A. The dependability and variety of features make Bulldog Security the leader in the industry.
OEM Remote Starter Detection How to Know if the vehicle is Equipped with an OEM Remote Starter 1. An “ENGINE STARTER” sticker should be on the remote. ENGINE STARTER 2. Remote start the OEM remote starter: Press the remote control’s lock button twice within 2 seconds, then press and hold the lock button for 3 seconds. x2 & Press & Hold .
AutoCommand Remote Car Starter is for automatic transmission / fuel injected gasoline vehicles only. It is an extremely sophisticated system with multiple built-in safety and security features. AutoCommand Remote Car Starter: Will start your car by remote control, and run the heater, defroster, or air conditioner to warm up or cool down .
9/8/2022 Club Car Wash Sites of Tidal Wave Express Car Wash 8 8/29/2022 Take 5 Car Wash Soft Touch Car Wash, Auto Oasis Car Wash, Clearwater Car Wash and Birdie's Car Wash 5 8/25/2022 WhiteWater Express Geaux Clean Car Wash 7 8/19/2022 ModWash Home Team Car Wash 3 8/18/2022 Splash In ECO Car Wash (Wills Group) Blue Hen Car Wash 2
3 Introduction 5 Life Skills 8 Discussion Starter 1 “Diversity” 9 Discussion Starter 2 “The Man and the Eagle” 10 Discussion Starter 3 “Color Blind” 11 Discussion Starter 4 “Crayons” 12 Discussion Starter 5 “The Crayon Box That Talked” 14 Discussion Starter 6 “If All the Trees Were Oaks” 15 Discussion Starter 7 “The Black Balloon”
Jul 11, 2014 · gine starts, rewire the starter kill to reach proper operation. Valet mode. Make sure the remote car starter is able to properly enter and ex it valet mode. When setting the remote car starter int o valet mode, pressing the lock button will lock the doors without activating the starter kill. (Refer to the user guide for further info rmation on .
Starter. In some areas, use of the Remote Engine Starter may violate state, provincial or local laws. Before using the Remote Engine Starter, check your state, provincial and local laws. * See your owner’s manual for more details. ** Provided that the remote start transmitter is within the operating range of the system. REMOTE START QUICK .
2) Starter Drive: Coat shaft with silicone lube (#7), prior to installing starter drive. Install new Starter Drive assembly (#5) and new Starter Drive Pin (#18). To install Drive Pin depress the Drive to gain access to the pin hole. Install new Pin flush with output shaft (starter drive end should fully seat over the pin). (see figure 8)
American Gear Manufacturers Association AGMA is a voluntary association of companies, consultants and academicians with a direct interest in the design, manufacture, and application of gears and flexible couplings. AGMA was founded in 1916 by nine companies in response to the market demand for standardized gear products; it remains a member- and market-driven organization to this day. AGMA .
