Linkage Parts - CNH Industrial
linkage partsand farm / industrial hardware
Linkage partsNOTES2LINKAGE PARTS AND FARM / INDUSTRIAL HARDWARE
Table of ContentsPRODUCTPAGE(S)Ball SocketsForged Weld-On Ball Ends.8Lift Arm.7Top Link.7BallsHitch.26Replacement.9Bushings, ReducerLift Arm.10Top Link.10ClevisesFarm.42General e.41Utility.41PRODUCTPAGE(S)Accessories.33-35Lift Arms and Lift Arm Parts.6Pins, HitchBent.21Blue/Gray Head.20Clevis Pins.16Double Lock.19Drop-Forged.17Fixed-Handle.16Red ars.11Accessories.11Pins, MiscellaneousDetent Pins.24Draw Pins (Lift Arm Pins).14Draw Pins (Clevis Type).13Hydraulic Cylinder Pins.25Locking Pins.24Lynch Pins.23"R" Clip Pins.22Stabilizer Pins.13Top Link Pins.15Cotter Pin Kit.22Drum Pump, 5-Gallon.37Raincaps.38Farm AccessoriesHay Hook.36Miscellaneous.36Top Link, Repair Ends.6Cylinder Stroke Control Segments.26Forged Top Links.5Harrow Teeth.27JacksRatchet.25Weld Collar.28Flange.29Weld Collar, zinc plated.30Marine and Recreational.31Heavy Duty Square.32StabilizerArms.12Brackets.12Chains.12Stay Straps.12Tool Boxes.38Wheel Spinners.39Index .43-45LINKAGE PARTS AND FARM / INDUSTRIAL HARDWARE3
Linkage partsThe three-point hitch systemMany of the products in this catalog are components ofthe typical tractor three-point hitch system that is standardon almost all farm tractors today. See illustration below.The basic function of the system is the attachment andadjustment of agricultural implements. The three primaryparts of the system are the top link and two lower lift armsas shown in yellow and red in illustration.Special pins are used to fasten the implement at these threepoints: top link pins and draw pins (lift arm pins). Adjustment ofone or all of these components allows the tractor operator toraise, lower or tilt an implement. The three-point linkage partsdescribed in this catalog are built to standard specifications setby the American Society of Agricultural Engineers (ASAE).Top Link PinTop linkpower takeoff shaftlift armlevellingassemblyadjustablestabilizerarmlift armlift armswingingdrawbardrawbarThe three primary parts of the 3 point hitch system are top link and two lower lift armsTOP LINK CONNECTIONTop link pins are always unthreaded and are heldin place by either a lynch pin, or in some cases, a large“R” clip pin. Top links and top link pins vary in length,but their respective ball socket holes and pin diametersare standardized by horsepower Category.LIFT ARM CONNECTIONMost lift arm pins are threaded on the end that bolts tothe implement bracket. The unthreaded end with thecross hole accommodates the ball socket of the lift arm.The lift arm is secured on the pin with a lynch pin or large“R” clip pin. Lift arms and lift arm pins vary in length, buttheir respective ball socket holes and pin diameters arestandardized by horsepower Category.4MAXIMUMDRAWBARHORSEPOWERTOP LINKPIN DIAM.PULL ORDRAW PINDIAM.STANDARDLIFT ARMSPACINGCategory 0 - up to 205/8"5/8"20"Category 1 - up to 453/4"7/8"26"Category 2 - 40 to 1001"1-1/8"32"Category 3 - 80 to 2251-1/4"1-7/16"38"Category 4 -135 to 3001-3/4"2"46"Category 0, 1, 2, 3 and 4 are used to classify tractors bydrawbar horsepower.The table shows the dimensions and the horsepower ratingsthat are associated with these five categories.LINKAGE PARTS AND FARM / INDUSTRIAL HARDWARE
Forged Top LinksQuality forged top links available inCategory 0, 1, 1 & 2 combination,2 and 3 sizes. All top links are yellow zincplated unless otherwise specified.The ends are clear zinc plated.ABCPIN HOLE SIZETHREADSBODY LENGTH05/8"3/4" NC8729916613/4"87299167187299168CLOSED LENGTHOPEN ed12.51-1/8" NC13-1/4"17"26"Plated17.43/4"1-1/8" NC16"21"31"Blue17.613/4"1-1/8" NC16"21"31"Plated17.68729917013/4"1-1/8" NC20"25"35"Blue19.18729917113/4"1-1/8" NC20"25"35"Plated19.18729917213/4"1-1/8" 31&23/4" & 1"1-1/8" NC16"21"32"Blue19.1872991741&23/4" & 1"1-1/8" NC16"21"32"Plated19.1872991751&23/4" & 1"1-1/8" NC20"25"35"Plated110.18729917621"1-1/8" NC16"21"31"Plated1108729917821"1-1/8" NC20"25"37"Plated1108729917921"1-1/4" NC15-3/4"20"30"Plated110.78729918021"1-1/4" NC16"23"32"Blue1128729918121"1-1/4" NC20"27"37"Plated112.68729918331-1/4"1-3/8" NC19-1/2"25-1/2"37"Black120LINKAGE PARTS AND FARM / INDUSTRIAL HARDWARE5
Linkage partsTop Link Repair EndsForged and welded screw-in repair ends forCategory 0, 1, 2 and 3 top links. Clear zinc plated.PARTNUMBERABCDCAT.TYPEPIN E QTY.WEIGHT (lbs.)872991881Forged3/4"1-1/8" NC (LH)6"10"12.4872991891Forged3/4"1-1/8" NC (RH)6"10"12.4872991902Forged1"1-1/4" NC (LH)5-1/2"10"13872991912Forged1"1-1/4" NC (RH)5-1/2"10"13872991922Forged1"1-1/8" NC (RH)6-1/2"11"13872991932Forged1"1-1/8" NC (LH)6-1/2"11"18872991943Forged1-1/4"1-3/8" NC (RH)7-1/4"12-1/8"18872991953Forged1-1/4"1-3/8" NC (LH)7-1/4"12-1/8"18Lift Arms And Lift Arm PartsCategory 1 lift arms and leveling bs.)87299729Category 1 right- or left-hand forged lift arm; fits all Ferguson models, Ford 2N, 8N, 9N, NAA, Massey-Ferguson35, 50, Oliver 550 and Oliver 3-point conversion, John Deere 1010; 7/8" pin holes; 31-3/4" ball centers;34-1/2" overall length111.787299731Category 1 lift arm leveling assembly; 18-1/2" closed; 25" open length;7/8" NF thread diameter; replaces Ford NCA577A16LINKAGE PARTS AND FARM / INDUSTRIAL HARDWARE
Top Link Ball SocketsWeld-on top link ball sockets to fitCategory 0 through Category 3 tractors.Available in black oxide and yellow zincdichromate plated versions.ABCDPIN HOLE SIZELENGTHTHRU BORESLEEVE WIDTHSLEEVE O.D.PACKAGEQTY.WEIGHT (lbs.)Standard duty, black oxide3/4"1-5/8"3/4"2"20.62Standard duty, black oxide1"1-3/4"7/8"2-3/8"20.89624602E2Heavy duty, black oxide1"1-3/4"1-3/16"2-3/4"21.89624603E3Standard duty, black oxide1-1/4"1-3/4"1-9/32"3-1/8"21.8SPC214E2Standard duty, plated1"1-3/4"7/8"2-3/8"20.8SPC215E1Heavy duty, plated3/4"1-5/8"7/8"2-1/8"20.7SPC216E1Standard duty, plated3/4"1-5/8"3/4"2"20.6SPC228E2Standard duty, plated1"1-1/4"7/8"2-3/8"20.8SPC235E1&2Standard duty, black oxide3/4" & 1"1-1/2" 600E19624601ELift Arm Ball SocketsWeld-on lift arm ball sockets to fit Category 0 throughCategory 3 tractors. Available in black oxide and yellowzinc dichromate plated versions.PARTNUMBERCAT.DESCRIPTIONPIN HOLESIZELENGTHTHRU BORESLEEVE WIDTHSLEEVE O.D.WEIGHT (lbs.)9624597E1Standard duty, black oxide7/8"1-3/8"7/8"2-3/8"0.99624598E2Extra heavy duty, black oxide1-1/8"1-3/4"1-3/8"3-1/8"1.99624599E3Standard duty, black d duty, plated7/8"1-3/8"7/8"2-3/8"0.9SPC224E2Standard duty, plated1-1/8"1-5/16"15/16"2-3/8"0.8SPC233E1&2Extra heavy duty, black oxide7/8" & 1-1/8"1-3/4" both1-3/8"3-1/8"1.7SPC2216E2Extra heavy duty, plated1-1/8"1-3/4"1-3/8"3-1/8"1.9LINKAGE PARTS AND FARM / INDUSTRIAL HARDWARE7
Linkage partsForged Weld-on Ball EndsHigh-quality, weld-on top link and lift arm ball sockets in Category 1, 2, and 3 sizes.Lift arm ends are available in straight and bent styles.BentLift arm endTop link QTY.872991981Top link end2"3/4"1-1/8"2-1/4"1/2"1-3/4"1872991992Top link end2-3/8"1"1-1/8"2-5/8"1/2"2"1872992001Lift arm 2012Lift arm 992041Lift arm end-bent4"7/8"1-7/8"2-5/8"5/8"1-3/8"1872992052Lift arm ft arm E PARTS AND FARM / INDUSTRIAL HARDWARE
Replacement BallsTop link and lift arm balls for Ford, John Deere, Oliverand other tractors. Designed to replace original balls.Yellow zinc dichromate plating.ABCPIN HOLE SIZELENGTHTHRU BOREBALLDIAM.John Deere & Oliver top link ball; replaces Deere F2680, Oliver 105968A3/4"1-3/4"2"12John Deere & Oliver top link ball; replaces Deere F2681, Oliver 104585A1"1-3/4"2"1872997361Ford lift arm ball; replaces Ford DDN995233; fits Ford 3000 and 40007/8"1-3/8"2-1/4"1872997372Ford lift arm ball; replaces Ford C5NN557A; fits Ford 50001-1/8"1-3/4"2-1/4"1872997381Oliver lift arm ball; replaces Oliver 105967A; fits modelswith claw-type lift arm7/8"1-3/8"2"1872997392Oliver lift arm ball; replaces Oliver 104591A; fits all modelswith claw-type lift arm1-1/8"1-3/4"2"1872997402Ford lift arm ball; narrow width; replaces C5NN557B1-1/8"1-3/8"2-1/4"1818226862Ford lift arm ball; heat treated, replaces TION87299734187299735LINKAGE PARTS AND FARM / INDUSTRIAL HARDWAREPACKAGEQTY.9
Linkage partsTop Link Reducer BushingsUsed in the pin hole of a top link to allow a smaller Category pin to fit.Yellow zinc dichromate plating.PARTNUMBERCAT.DESCRIPTIONOUTSIDE DIAM.INSIDE DIAM.LENGTHPACKAGEQTY.872992080-1Fits all Category 0 top link pins3/4"5/8"1-5/8"5872992091-2Fits all Category 1 top link pins; replaces Ford C7NN6993A1"3/4"1-15/16"5872992101-2Fits all Category 1 top link pins; short1"3/4"1-5/8"5872992112-3Fits all Category 2 top link pins1-1/4"1"1-15/16"5Lift Arm Reducer BushingsUsed in the pin hole of a lift arm to allow a smaller Category pin to fit.Yellow zinc dichromate plating.PARTNUMBERCAT.DESCRIPTIONOUTSIDE DIAM.INSIDE DIAM.LENGTHPACKAGEQTY.872992140-1Fits all Category 0 lift arm pins7/8"5/8"1-3/8"5872992151-2Fits all Category 1 lift arm pins; Ford C7NN6992A1-1/8"7/8"1-3/4"5872992161-2Fits all Category 1 lift arm pins; replaces John Deere F26841-1/8"7/8"1-3/8"5872992172-3Fits all Category 2 lift arm pins1-7/16"1-1/8"1-3/4"5872992182-3Fits all Category 2 lift arm pins; extra long1-7/16"1-1/8"3-1/4"5872992192-3Fits all Category 2 lift arm pins; 15/32" lynch pin hole1-7/16"1-1/8"2-1/2"5872992202-3Fits all Category 2 lift arm pins1-7/16"1-1/8"2-3/4"510LINKAGE PARTS AND FARM / INDUSTRIAL HARDWARE
DrawbarsOne-piece 3-point hitch cross drawbars to fitCategory 0 through Category 3 tractors.8729922787299226PARTNUMBERCAT.NO. OF HOLESLift ArmSpacingAHole DiameterBPin DiameterCThicknessDWidthECOLORPKG.QTY.WEIGHT /16"1-3/4"3-1/2"Black165Tractor Drawbar accessoriesDO NOT EXCEED WORKING LOAD LIMIT. FARM HARDWARE IS NOT FOR LIFTING.PARTNUMBERDESCRIPTIONWORKING LOADLIMIT (lbs.)PACKAGEQTY.87299607For all tractor drawbars up to 1-5/8" thick;for use with 5/16" to 1/2" chain9,000187299240Drawbar lock18729924087299607LINKAGE PARTS AND FARM / INDUSTRIAL HARDWARE11
Linkage partsStabilizer Arms & BracketsReplacement stabilizer arms for stabilizer kits and a variety of tractors.Stabilizer arms increase the stability of the tractor lift arms.Stay straps for Category 1 tractors are used to maintain an implement at a set height.Universalstabilizer armAdjustable forgedstabilizer armStay strapStay chainassemblyStabilizer chainStabilizerbracketPART per stay strap for Category 1; fits all Ferguson models, Ford 2N, 8N, 9N, NAA, 600, 700, 800, 900,Oliver 550 and all Oliver 3-point conversions, Massey-Ferguson 35 and 5012.887299244Lower stay strap for Category 1; fits all Ferguson models. Ford 2N, 8N, 9N, NAA, 600, 700, 800, 900,Oliver 550 and all Oliver 3-point conversions, Massey-Ferguson 35 and 5012.487299246Right or left universal stabilizer arm; 7/8" pin holes on 31-9/16" centers1687299247Right or left universal stabilizer arm; replaces Massey-Ferguson ST96362358; 7/8" pin holeson 33-1/8" centers16.487299249Heavy-duty adjustable forged stabilizer arm; fits all Ferguson models, Ford 2N, 8N, 9N, NAA, 600, MasseyFerguson 35, 50, 175, 65, 135, 150, 165, 180; adjustable from 28-1/2" to 36" ; 7/8" pin holes; 7/8" NF threads1687299254Universal stabilizer arm; 7/8" pin holes on 31-9/16" and33-1/8" centers; 3 hole16.187299750Pair of universal stabilizer chains for most Category 1 applications;yellow zinc plated11412LINKAGE PARTS AND FARM / INDUSTRIAL HARDWARE
Stabilizer PINSStabilizer stub pins for Ford, Ferguson and other stabilizer kits.Yellow zinc dicromate ERALLLENGTHTHREAD DIAM.PACKAGEQTY.87299259Replaces Ford 230044, Massey-Ferguson 18177M17/8"3/8"2-5/8"5/8" NF587299261Replaces Ford 141185, Massey-Ferguson MF668154M17/8"1-1/4"3-1/8"5/8" NF587299262Stabilizer stub pin7/8"1/2"2-5/8"5/8" NF587299263Replaces MF186802M17/8"11/16"3-1/8"3/4" NF5Clevis-Type Draw PinsFor use with implements with yoke type mountings.All pins are yellow zinc dichromate plated.Head type87299303 Categories 2 and 3Roll pin typePARTNUMBERCAT.TYPEPINDIAM.USABLELENGTHOVERALL LENGTHPACKAGEQTY.872992941Roll Pin7/8"4-1/2"6"1872992952Roll Pin1-1/8"3-5/16"4-3/4"2872992962Roll Pin1-1/8"4-3/4"6-1/2"1872992972Roll Pin1-1/8"5-3/8"7"2872992982Roll Pin1-1/8"7-3/8"9"1872992992Roll 872993023Roll Pin1-7/16"6-1/4"8-1/2"2872993032&3Head1-1/8" & 1-7/16"3-5/8" & 4-1/4"9-1/4"1LINKAGE PARTS AND FARM / INDUSTRIAL HARDWARE13
Linkage partsDraw Pins (Lift Arm Pins)Forged and adjustable Category 0 through 3 draw pins for a variety of applications. Allpins are yellow zinc dichromate plated.Category 1 & 2,Forged Implement PinCategory 1Category 2PART NUMBERCAT.DESCRIPTIONPINDIAM.USABLE LENGTHOVERALL LENGTHTHREAD -7/8"5/8" NF1872992701Adjustable7/8"Adjustable5"7/8" NF1872992721Forged7/8"1-3/4"5-1/2"7/8" NF1872992741Adjustable; extra long7/8"Adjustable6-1/4"7/8" NF1872992751Forged; extra long7/8"2-1/4"6-1/2"7/8" NF1872992781Forged7/8"2"5"5/8" NF1872992791Forged7/8"1-3/4"4-1/2"5/8" NF1872992801 to 2Forged1-1/8"2-1/4"6-5/16"7/8" NF1872992811 to 2Adjustable1-1/8"Adjustable5-1/4"7/8" NF1872992821 to 2Forged1-1/8"1-13/1
linkage parts and farm / industrial hardware 9 replaCement balls Top link and lift arm balls for Ford, John Deere, Oliver and other tractors. Designed to replace original balls. Yellow zinc dichromate plating. PRODUU CT AGO ERD( SG)EOMPDMaC R A E PREnRyGU PMCUtahGU)MeG hGCyDtU oDf(DtOTUAaOG ARhhU SMR (
Canada mail original to CNH Industrial Capital America LLC, Attn: WLL Agreement, 4475 North Service Rd, Suite 301, Burlington, ON L7L4X7 Canada Case is a registered are trademark in the United States and many other countries, owned by or licensed to CNH Industrial N.V., its subsidiaries or affiliates
2-5 UltraLift Concept 16 3-1 Watt’s Straight Line Mechanism 19 3-2 Fully Prismatic Linkage 19 3-3 One Replace Prismatic 20 3-4 Two Replaced Prismatics 21 3-5 Fully Revolute Linkage 22 3-6 Scissors Linkage 23 3-7 Parallel Linkage 24 3-8 Parallel Linkage with a Cam 24 3-9 Constant orientation linear linkage 25 3-10 Hydraulic Mechanism 25
CNH Capital Australia Receivables Trust Series 3 A [346.3] million . Investor Guide CNH Capital Australia Receivables Trust Series 3 Page 2 CNH Capital Australia Receivables Trust Series 3 – Issue Summary . Back Up Swap Provider Citibank N.A., Sydney Branch (ABN 34 072 815 058) IMPORTANT DATES Statistical Pool Cut-off
Case IH is a trademark registered in the United States and many other countries, owned by or licensed to CNH Industrial N.V., its subsidiaries or affiliates. Any trademarks referred to herein, in association with goods and/or services of companies other than CNH Industrial America LLC, are the property of those respective companies.
CNH Industrial Capital is a trademark in the United States and many other countries, owned by or licensed to CNH Industrial N.V., its subsidiaries or affiliates. www.caseih.com *For commercial use only. Customer participation subject to credit qualification and approval by CNH Industrial Capital Canada Ltd.
4-bar linkage knee mechanism has a collection of instan-taneous centers of rotation. Many physicians prescribing AK- and TK-prostheses are not familiar with the trajectory of the instantaneous center of rotation of 4-bar linkage knee mechanisms applied. A 4-bar linkage knee mechanism is intrinsically extension-stable, meaning without extension
Christen, Peter. 2012. Data matching: concepts and techniques for record linkage, entity resolution, and duplicate detection. Springer Science & Business Media. Fellegi, Ivan P and Alan B Sunter. 1969. “A theory for record linkage.” Journal of the American Statistical Association 64(328):1183–1210. Dunn, Halbert L. 1946. “Record linkage.”
paper (if used) should be placed inside the front cover of the answer book. Rough work should be scored through. All questions should be attempted. Candidates should note that Question 10 contains a choice. Question 1 is on Pages 10, 11 and 12. Question 2 is on Page 13. Pages 12 and 13 are fold-out pages. NATIONAL QUALIFICATIONS 2014 FRIDAY, 16 MAY 1.00 PM – 3.30 PM [X274/13/02] Page two .
