Manual P5/EP5 - Flowserve
Manual P5/EP5PMVValveControlSystemalve Control System–1–
Manufacturers declaration Hersteller-Erklärung Déclaration de fabricantGBManufacturers declarationin compliance with EC directive 89/392/EEC, annex II B and 89/336/EEC.We hereby confirm that the appliances described in this sheet has been manufactured incompliance with the applicable standards and is intended for installation in amachine/application, and that commissioning is strictly prohibited until evidence has beenprovided that the machine/application in question is also in compliancewith EC directive 89/392/EEC and 89/336/EEC.This manufacturers declaration is applicable to the following PMV-Positioner series:P5, EP5, F5.DHersteller-Erklärungim sinne der EG-richtlinie 89/392/EWG, Anhang II B und 89/336/EWG.Hiermit erklären wir, daß die in diesem Blatt beschriebenen Geräte entsprechend den gültigenNormen gebaut und zum Einbau in eine Maschine oder Applikation bestimmt sind, sowie daßderen Inbetriebnahme so lange untersagt ist, bis festgestellt wurde, daß dieseMaschine/Applikation ebenfalls der EG-Richtlinie 89/392/EWG und 89/336/EWG entspricht.Diese Herstellererklärung hat für folgende PMV-Stellungsregler-Serien Gültigkeit:P5, EP5, F5.FDéclaration de fabricantau sens dela directive de la CE 89/392/CEE, annexe II B et CE/89/336/CEE.Nous déclarons par la présente que les appareils décrits sur cette page sont construits enconformité avec les normes en vigueur et qu'ils sont destinés à être montés dans une machineou une application, nous déclarons également que leur mise en service est interdite tant qu'il n'apas été constaté que cette machine/application satisfait égalementà la directive CE 89/392 CEE et CE/89/336/CEE.Cette déclaration de fournisseur est valable pour les types d'appareils PMV suivants:P5, EP5, F5.Mr. Roland WedebrandPresident, Palmstiernas Instrument AB–2–
ContentsPage1.Introduction1.a Storage Instructions, Storage Seal45-62.Function73.Air requirements84.Installation85.Connections96.Front cover and the indicator cover107.Span and zero adjustment118.Indicator adjustment129.Cam adjustment1210.Dampers1211.I/P Unit, EP51312.How to mount the I/P Unit1413.Maintenance15-19Pilot valve15Diaphragm16Feedback spring17Balance arm17Lower arm18O-rings18Filter plug1914.Feedback Unit2015.Trouble shooting2116.Technical Data2117.Exploded Drawing2218.Spare part list23Approvals24-27–3–
1.IntroductionAlways check www.pmv.nu for latest edition of manual.The P5 Valve Control System is a valve positioning system from PMVwith a modular design concept.The base unit of the system is the pneumatic positioner, used in eithersingle or double acting applications. P5 comes standard with built indampers, a 5 mm high gain spool valve assembly, gauge ports and anO-ring sealed housing. The housing utilizes a unique O-ring seal thatcan be adjusted to a sealed or drained position.The modular design concept allows for easy addition of accessoriessuch as I/P converter and/or a feedback package, both which areisolated from the basic pneumatic unit. These accessories can be factoryor field mounted.Ease of calibration and maintenance are built into to the design witheasily accessible span and zero adjustment, and very simple partsreplacement.Fail FreezeI/P ModuleExplosion proof I/P moduleStandard or I/SI/P-convertermoduleP5 pneumatic positionerDomeindicatorMountingadapterplateF5 feedback moduleGaugesMounting bracketSpindlesF5 Explosion Proof–4–
1.aStorage instructionsPMV Positioner and feedback module storageand handling proceduresPMV Positioners and feedback modules are precision instruments which should be storedand handled accordingly to avoid problems or damage.Electropneumatic positioners/feedback modules contain electronic components whichcan be damaged by exposure to excessive water. Appropriate precautions should be takento protect units while in storage.Warehouse storageStored in original PMV shipping containers, units should be stored in an environmentallycontrolled area, i.e. clean, cool (15-26 C, 60-80 F) and dry, out of direct sunlight or weatherexposure.Field storageNote: Once the air supply to the positioner is connected and turned on, internal air bleedwill prevent the ingress of moisture and protect the unit from corrosion. It is recommendedthat the air supply be left on at all times. If units are installed immediately, turn, and leave on, the air supply. If positioners must be stored outdoors, tighten all covers which may have loosened inshipment, make sure all open enclosure entry points are sealed.Feedback modules should have cover tightened and conduits entries sealed. Positioners/Feedback modules should be wrapped and sealed air and watertight with desiccant insidethe plastic, units should be securely covered with an opaque cover and not exposed todirect sunlight, rain or snow.Pneumatic positionersUnits should have all ports sealed and be protected from direct exposure to weather.For long term storage ( 1 month) or overseas shipment units should be protected withplastic and desiccant.Potential damage mechanismWhen units are stored in hot, humid climates, the daily heating/cooling cycle will causeair to expand/contract and be drawn in and out of the positioner/feedback housing.Dependent on the local temperature variations, humidity and dew pointsand time in storage condensation could occur and accumulate inside on the I/P Convertercausing erratic operation or failure due to water and corrosion. The potential forcondensation damage is especially high in southern climates and aggravated if units areexposed to direct sunlight.For further assistance, please contact you nearest PMV office.–5–
Storage SealP5/EP5 is supplied with all enclosure entrypoints sealed.The seal is only a storage seal, notto be used as seal when P5/EP5 is in operation.If Storage Seal is removed or damaged, makesure all open enclosure entry points are properresealed before further shipping or storage.Use circular stickers marked I, S and OUT,supplied on Storage Seal or vapour proof tape.P5Remove Storage Seal from connection block,mount positioner on actuator/valve, makeconnections according to section 5, (Page 9).Calibrate span and Zero according to section 7,(Page 11).Clean any oil/debris off the connecting block,then reseal open enclosure entry ports, usecircular stickers marked I, S and OUT, suppliedon Storage Seal or vapour proof tape.P5-SEALEP5Follow P5 instructions as above. RemoveStorage Seal for conduit entry IE, connect inputsignal cable and install proper cable gland tosecure the units sealing.IP5-SEAL–6–
2.FunctionThe P5 operates on a force balance principal. Force is originated by thesignal pressure transmitted through a diaphragm on to the balancearm. The opposing force is achieved through the feedback spring andis proportional to the position of the lower arm. The lower arm position is determined by the position of the cam which is secured to thespindle and connected to the actuator shaft thus providing the feedback from the actuator/valve. When these two forces are equal, thebalance arm and the spool in the pilot valve are in a neutral position-the complete unit is in a balanced position. Air is supplied to the pilotvalve through port S, and controls the air flow through ports C1 andC2Assume an equilibrium position.An increased control pressure will deflect the diaphragm 1 down,compressing the feedback spring 3. The balance arm 2 moves the spool7 in the pilot valve 8 furnishing supply air to the actuator, while at thesame time air is exhausted from actuator and is vented to atmospherethrough the pilot valve and the OUT port .With the increased supply air, the actuator rotates (or moves linearly)moving the positioner spindle 6. The spindle and cam 5 rotate, forcingthe lower arm 4 upwards compressing the feedback spring 3. Thismotion will continue until the two forces are equal and the unit is in anequilibrium position.12783564–7–
3.Air requirementsMaximum supply pressure is 1 MPa (150 psi).Supply air shall be clean, dry and free from oil, water, moisture, foreign parts anddebris.The air shall be freeze-dried or similar to a dew point of at least 10 C (18 F) belowlowest expected ambient temperature.A 40µ filter/regulator is recommended to be installed as close to P5/EP5 aspossible to ensure proper supply air quality.Before making pneumatic connections to the positioner, it is recommended thatthe supply air lines are opened up and allowed to vent for 2-3 minutes to clear anydebris from the line. It is further recommended that a large paper bag is used tocollect any oil or humidity that may be present in the line during this purging,direct the air flow into the bag. Should exessive amounts of oil and/or humiditybe present at this stage, a review of the pneumatic system should be carried outand the problem corrected.Poor air quality is one of the major causes of premature failureof pneumatic equipment.4.InstallationP5 mounts on to the actuator using either the ISO F05 holes 4 and a PMV ISOmounting kit or by using the optional mounting adaptor and screws 5 tomount P5 on to existing PMV mounting kits.Proper alignment of the positioner spindle to the actuator shaft is veryimportant since improper alignment can cause excessive wear and friction tothe positioner.The spindle/positioner shaft assembly allows for quick and simple spindlechanges. To ensure the proper connection, the spindle 3 has a spring clip 2that must be properly installed. A solid ”click" should be felt when assemblingthe two pieces insuring that the two flats 1 are engaged into the positionershaft groove.The spindle can be removed, by inserting two screwdrivers under the twotapered surfaces of the spindle and bending carefully. When the spring clipreleases the spindle will eject.21354–8–
5.ConnectionsAir connections are tapped for 1/4" G or NPT male connectors and areclearly marked. Gauge ports are for 1/8" G or NPT.We recommend use of tape, Loctite 577 or similar user preferred forsealing.Electrical connection on I/P unit accepts 1/2" NPT or PG 13,5 (M20)cable gland.Port IPort SPort C1, C2OUTPort IpPort IEPort PInput instrument pneumatic signal 20-100kPa (3-15 psi)Supply air, maximum 1 MPa (150 psi) Minimum 0,15MPa (21 psi) for EP5Actuator connections (0,2-1 MPa). C2 opening port.Exhaust air port. Do not block! Exhaust filter optional.Gauge port for pneumatic input signal.Input electric signal (4-20 mA) (On the I/P unit.)Gauge port for I/P unit output pressure ( On the I/P unit)Ports Ip, P, S, C1 and C2 are sealed withplugs. To install gauges, unscrew plugsand replace with gauges.We recommend use of tape, Loctite 577or similar user preferred for sealing.Port OUT is for venting the unit. All airfrom the positioner, actuator andI/P unit is vented to atmosphere throughthis port. Do not block this port. A highflow silencer or an exhaust pipe can beconnected to this port to prevent foreignobjects from entering and blocking theunits exhaust. Connector in exhaust portmust not have less than 9 mm (3/8“)orfice.When using gases other than air forsupply – Please contact PMV.On EP5 (P5 with I/P unit installed) I/Punit is supplied with air from port S.Port I is automaticly sealed off andprotected. No connection shall be madeto this port. See pages 13 and 14 for moreinformation.For single acting operation plug port C1for increasing signal to open valve. PlugC2 for decreasing (reverse) signal to openvalve.–9–
6.Front cover and indicator coverThe front cover of P5 is secured to the pneumatic unit with fourcaptured screws and sealed with an O-ring 1. The O-ring can belooped over notches 2 in the front cover to allow for drainage.There are eight locations on the front cover where the O-ring can belooped. This O-ring system is common to the Pneumatic unit , I/P unitand Feedback unit in the PMV Valve Control System P5. This uniquesealing system allows for complete sealing or draining of the units bychanging the position of the O-ring.The indicator cover 3 is O-ring sealed and secured by a bayonetcoupling. The indicator cover is also used to secure the identificationcover 4.To remove the indicator cover turn it slightly counterclockwise until itloosens. Identification cover and O-ring 5 are now removable.When installing indicator cover and identification cover make sure thatthe O-ring is properly engaged.115432– 10 –
7.CalibrationP5/EP5 is when shipped from PMV precalibrated for 90 0,5 deg rotation, (can also be30, 45 or 60 deg, see installed cam).For most applications the valve closed positionis more critical than valve open position,most attention should be paid at valve closedposition. Always start calibration procedure byapplying 0 % input signal, then adjusting zero.P5/EP5 is calibrated by turning thumb wheels 1& 4.Arrows on arm 5 indicate turning direction ofthumb wheels. “ “ Increase zero/span “-“ Decrease zero/span546Calibration procedureCheck cam seating, section 9 before startingcalibration procedure.1. Apply 0 % input signal (0% 20 kPa/3 psior 4 mA)2. Wait for steady state.3. Adjust zero by turning the silver (lower)thumb wheel 4 with finger or with screwdriver 7 from the outside.4. Apply 100% input signal (100% 100 kPa/15 psi or 20 mA)5. Wait for steady state then memorize result.6. Apply 0% input signal.7. Adjust span if necessary. This is done byfirst loosing screw 2, then turning theyellow (upper) thumb wheel 1 “ “ or “-“and finally tighten screw 2. Spring top mustnot be in contact with spring guide 3.8. Check zero and adjust if needed.9. Repeat steps 2 to 8 until desired calibrationis achieved.7321– 11 –
8.Indicator adjustmentTo adjust the indicator, take off front cover and pull the indicatorupwards until it comes off the Allen screw.Before installing the indicator make sure that the Allen screw istightened. Press the indicator on the screw and adjust it by rotatingclockwise to desired position.9.Cam adjustmentWith the cover and indicator removed, loosen the screw 1 and turn thecam locking nut 2 counterclockwise until the cam loosens. Adjust thecam 3 as desired making sure that the ball bearing 4 always is ridingon an active lobe on the cam. To secure the cam, make sure that screw1 is backed out from the locking nut 2 then finger tighten the lockingnut and tighten screw 1. Install and adjust the indicator and reinstallcover.6")2m-2 m1(1/141correctincorrect310.DampersThe standard built in dampers 5located on the connecting block provide a simple means of adjusting theactuator travel speed.For maximum actuator travel speeddampers shall be adjusted to minimum damping position. (Fig).Double acting actuators – adjustonly OUTLET damper, set SUPPLYdamper in minimum damping position.Single acting actuators – adjust bothdampers for desired operation.5– 12 –
11.I/P Unit, EP5WARNING! Units installed in hazardous areas must have proper approvals.The I/P unit is mounted directly on top of the positioner unit.No external air supply is needed since the I/P unit is supplied with air from thepositioner unit.Port I on the positioner unit will be plugged when the I/P unit and theappropriate gauge block gasket installed.The I/P unit accepts a 4-20 mA inputsignal.The I/P unit is equipped with a built in 30 micron filter (Fig 4).Caution: Do not operate the unit without filter and filterplug installed.Do not unscrew filterplug when the positioner is pressurized.Span and Zero for the I/P converter is factory setand can not be adjusted12– 13 –
12. How to mount the I/P Unit to the positioner UnitSwitch off supply air and disconnect input signal – port I.Loosen screws 3 and remove connection block 1, the gauge or plug fromport Ip, the fitting from port I and existing gasket 4. Carefully installgasket 6 supplied together with I/P unit. When correct installed port Iwill be blocked by the gasket.Make sure that relief valve spring 5 is installed properly. Install theconnection block 1 to the positioner unit 2.Remove cover on I/P unit.Install the I/P unit to the top of the Positioner unit, making sure that thefour O-rings are present and properly seated. Tighten the unit with thethree screws. (See fig. 1 and 2 page 13) Screw 1 first, screw 2 last.WARNING! Units installed in hazardous areas must have properapprovals.Connect input signal cable to port IE and tighten the cable gland (see fig 5on page 13). Adjust the O-ring on the I/P Unit housing to desired position - sealed or drained. (See fig 3 on page 13 or section 6 on page 10).A gauge indicating output signal from the I/P converter can be installedin port P. Make sure that the filter plug is tightened before supply air isswitched on (Fig 4 on page 13).624153– 14 –
13.MaintenancePilot valveTo remove the pilot valve for cleaning or inspection, remove the screw1 and carefully lift out the complete assembly 2. Gently remove thespool 3 from the block and clean the parts, using methylate cleaner orsimilar. Blow the parts dry with compressed air. Install the spool intothe pilot valve housing, place it on a flat surface, then lift it carefully inone end. Before reaching 20 deg angle the spool should move by itself.Should the parts show signs of wear, a new assembly is recommended.Mixing spool valves and valve bodies may result in very high bleedrates and poor performance. Check the O-rings, then secure and installthe pilot valve assembly into positioner unit, press it towards thepositioner housing wall and secure it with screw 1. Make sure that theleaf spring 4 on the balance arm 5 is properly fitted in the groove onthe spool 6. Check again to insure smooth operation of the assembly.To maintain original factory performance specifications, use only spoolvalve assemblies supplied by PMV362541– 15 –
DiaphragmIf P5 is equipped with I/P unit (EP5), the I/P unit must be removed toaccess the diaphragm.When installing the diaphragm make sure to place one washer on eachside of the diaphragm.Put some Loctite 577 on the thread, install the screw 3 and tighten.Make sure the diaphragm is centered.Check the O-ring for the diaphragm cover 2, install the O-ring into thepositioner housing, then install cover 2. Secure crosswise with screws 1,first turn loosely. Torque shall be 4,5 Nm (40 in-lbs).– 16 –
Feedback spring2Once the front cover andindicator are removed,the feedback spring canbe easily accessed.Hold the spring 1 fromthe top, pull down andout.When installing, holdthe assembly at the top,guide the lower part toposition on the zeroscrew, then press downuntil it fits easily underthe balance arm 2. Makesure that the assembly isaligned properly againstthe lower arm and thenotch is engaged in thetab on the balance arm 2.1Balance armThe balance arm canonly be removed afterI/P unit, diaphragm andfeedback spring havebeen removed. (Seesections above and onpage 13, 14 and 16).Loosen the screws 3 andthe balance arm can beremoved.When installing thebalance arm make surethat the leafspring 4 onthe underside of thebalance arm 5 isproperly engaged intothe groove 6 of the spoolin the pilot valve.Tighten the two screws 3holding the balance armto the positioner.3654– 17 –
Lower armOnce the front cover is removed, the lower arm can be easily accessed.Remove the indicator, feedback spring and the cam.Loosen screw 2 and remove twist stop 1.Remove screw 3, lower arm 4, rod 5 and spring 6.Check rod and lower arm for wear, replace if necessary. Clean the rodand install it in the lower arm. The lower arm should move easily andsmoothly.Install the lower arm and rod assembly into the positioner housing,making sure that the spring 6 is attached properly to the lower armand positioner housing.Secure the lower arm and rod assembly with the screw 3.Check again that the lower arm moves smoothly.Apply a small amount of grease on the small tongue on the lower arm,then install and secure the twist stop.Install cam, feedback spring, indicator and front cover.436215O-ringsWith time and use, O-rings can become brittle. This can cause pooroperation and even failure of the positioner.Always check O-rings when performing any work on the positionerand replace bad O-rings.A thin layer of silicon grease applied on the NBR (Black) O-ringsprolongs their life. On Q (red) O-rings, use a non silicon based grease.– 18 –
Filter plugCaution! Do not operate the unit without filter and filter pluginstalled. Do not attempt to unscrew filter plug while positioner ispressurized.EP5 is equipped with a built in secondary filter located on theside of the I/P unit.For replacement or inspection, make sure that positioner unit is notpressurized, then unscrew filter plug 1. Remove filter 3 and install anew into the filter plug . Check condition of O-ring 2 and filtercompartment. If moisture is found, check upstream filters/oil-waterseparators. Moisture can cause I/P failure.Reinstall filter plug.321– 19 –
14. Feedback UnitSee feedback module instructions for connections and calibration.The P5 or EP5, Valve Control System, can easily be equipped with a Feedbackunit, model F5. This unit will mount directly on top of the Pneumatic positioner replacing the positioner front cover. The O-ring located on the bottom ofthe Feedback unit, F5, will provide the same sealing or draining capabilitiesas the front cover. The indicator and front cover from the positioner unit canthen be installed on to the Feedback unit.WARNING! Units installed in hazardous locations must have properapprovals.Installing the feedback unit.— Remove the front cover, indicator, and Allen head screw fromthe top of the positioner spindle.— Install the drive coupling 4 and adjust the O-ring seal on the bottom ineither sealed or draining position. (See section 6, page 10).— Install the Feedback unit 9 on top of the Positioner unit, makingsure the coupling is properly engaged before tightening the fourscrews 5.— Make electrical connections and tighten cable glands.(See F5 manual for details).— Adjust cams and/or potentiometer to desired position.— Install the indicator and front cover.95243O-ring seal– 20 –
15.Trouble shootingNote: All PMV-positioners are serialized. Please notedown, and provide the serial number when contactingthe factory for trouble shooting or service.Signal change results in actuator running to end positions.— Check coupling between positioner and actuator.— Check cam position and locking screw.— Check input signal.Signal change has no effect on the actuator position.— Check indicator and screw.— Check air supply to positioner and tubing to theactuator.— Check input signal to positioner.— Check diaphragm for damage or leakage.— Check pilot valve function.— Check cam for correct setting.— Check I/P outputInaccurate positioning.— Dirty or worn pilot valve.— Defective or leaking diaphragm.— Input signal fluctuates.— Incorrect sizing of actuator.— Valve/actuator "stiction".— High valve/actuator breakaway torque.— Loose cam.16.Technical DataInput SignalLinearityHysteresisP5EP520-100 kPa/3-15 Psi (6-30 optional) 0,5%* 0,75%*4-20 mA 0,5%* 0,5%* 0,5%*(pressure 600 kPa/87 Psi) 1 000 (kPa/kPa)Min 66%/% ISA S75.13Air consumption at Supply pressure:RepeatabilityGain0,2 MPa/29 Psi0,4 MPa/58 Psi0,6 MPa/87 Psi0,8 MPa/116 Psi5,4 nl/min12,3 nl/min20 nl/min27,8 nl/min0.19 SCFM0.43 SCFM0.71 SCFM0.98 SCFM1 MPa/145 Psi35,7 nl/min 1.26 SCFMAir delivery at Supply Pressure:0,2 MPa/29 Psi200 nl/min 6.9 SCFM0,4 MPa/58 Psi370 nl/min 12.8 SCFM0,6 MPa/87 Psi0,8 MPa/116 Psi1 MPa/145 PsiSupply Pressure 0,5%*6,1 nl/min13,6 nl/min22 nl/min30,5 nl/min0.22 SCFM0.48 SCFM0.78 SCFM1.08 SCFM39 nl/min1.38 SCFM540 nl/min 18.8 SCFM710 nl/min 24.7 SCFM880 nl/min 30.6 SCFMMax 1 MPa/150 PsiTemperature rangeConnector threadsGauge threadsWeight std.1,1 kg/2.4 lbs0,15-1 MPa/21,8-150 Psi-20 C to 85 C (-4 F to 185 F)1/4" NPT or G1/8" NPT or GWeight with gauges 1,3 kg/2.9 lbsIngress protection1,5 kg/3.4 lbs1,8 kg/3.9 lbsIP 66/NEMA 4* Per cent of full scale.(The information in this manual is subject to change without notice.)– 21 –
17.Exploded Drawing00-1384– 22 –
18.Pos Part noSpare part listQty P5-AS13/630 -25P5-26P5-27P5-29P5-30P5-31111111132 P5-3235 P5-xx/xx36 12047N36 12047G37 P5-Kxx38-45, P5-Screws75-8046-53 P5-Seal NBR81-83, 6 , 67, 7046-53 P5-Seal Q81-83, 6 , 67, 7054 P5-Sxx114411111HousingFront Cover incl. O-ringConnecting block NPT 1/4"assemblyConnecting block G 1/4"assemblyRelief valve springGasket for P5Gasket for EP5Diaphragm cover incl. O-ringDiaphragmDiaphragm washerBalance armFeedback spring 3-15 psiassemblyFeedback spring 6-30 psiassemblyLower arm assemblyRodSpringIndicator ArrowIndicator FlagIndicator PointerIndicator cover Transparentincl. O-ringIndicator cover Flagincl. O-ringIndicator cover Blindincl. O-ringTwist stopPilot valve incl. O-ringsShaft incl. O-rings, screwCam locking nut incl. screwZero coverCoverMounting adapter, inclscrewsBall bearingIdentification coverPlug NPT 1/8"Plug 1/8" GCamScrew set P5/EP598.9I/P UNIT Part E5-AS3GP5-4E5-5E5-6E5-7E5-STDE5 N-AS 11E5 G-AS 11FU-STDE5-EX/EU74E5-EX/US184E5-FS111I/P boxI/P cover incl. screwsI/P nose NPT 1/4" assemblyI/P nose G 1/4" assemblyRelief valve springFilter plug incl. Filter 66, O-ring, 81Filters (5 per package)Gasket I/PI/P converterMounting bracket Round I/Pincl. screws, O-rings, I/P NoseEnclosure incl. I/P converter Std.Enclosure incl. I/P converter,flameproof CenelecEnclosure incl. I/P converter,Explosionproof FM, CSAI/P converter fail in last positionincl. bracketO-ring set P5/EP5Nitrile, NBRO-ring set P5/EP5Silicone, QSpindle adaptor– 23 –
Approvals E5-IS/EU– 24 –
Approvals E5-EX/EU– 25 –
Approvals E5-IS/US & E5-EX/US 1– 26 –
Approvals E5-IS/US & E5-EX/US 2– 27 –
WARNING!Installation of any hazardous area equipment should be made in accordance withhazardous area installation codes and also of course to the installation to the installationand operating instructions provided. The manufacturer cannot be held responsible forincorrect installation or any customer modifications to, or repair of, a certified instrumentas this may invalidate the certified design. If a certified instrument shoult fail, no attemptshould be made by the user to effect repair. The unit should be returned to the factory.WARNING!These instruments must be installed in accordance with local and national codes ofpractice, especially for hazardous area installations. The instruments are fully isolatedfrom ground and therefore grounding is unnecessary for functional purposes.However, grounding may be necessary to conform to installation codes.Approvals EP5-IS (I/P-converter with white label)– 28 –
FM– 29 –
CSA– 30 –
CENELECATEX– 31 –
Palmstiernas Instrument ABKorta Gatan 9SE-171 54 SolnaSWEDENTel: 46 (0) 8 555 106 00Fax: 46 (0) 8 555 106 01E-mail: info@pmv.nuInternet: www.pmv.nuSUBSIDIARIES:PMV GmbHSperweg 16D-41468 NeussGERMANYTel: 49 (0) 2131 795 74-80Fax: 49 (0) 2131 795 74-99E-mail: info@pmv-germany.deInternet: www.pmv-germany.dePMV-USA, Inc1440 Lake Front CircleUnit 160The Woodlands, Texas 77380USATel: 1 281 292 7500Fax: 1 281 292 7760E-mail: pmvusa@pmvusa.comInternet: www.pmvusa.comPalmstiernas Svenska ABBox 21SE-663 21 SkoghallSWEDENTel: 46 (0) 54 52 14 70Fax: 46 (0) 54 52 14 42E-mail: info@palmstiernas.seInternet: www.palmstiernas.se23740/2002.14 EkvatorPMV Controls LtdHeadlands Business ParkRingwoodHampshire BH24 3PBENGLANDTel: 44 (0) 1425 48 08 88Fax: 44 (0) 1425 48 08 89E-mail: sales@pmv-controls.ltd.ukInternet: www.pmv-controls.ltd.uk(The information in this brochure is subject to change without notice.)Distributor– 32 –
Maschine/Applikation ebenfalls der EG-Richtlinie 89/392/EWG und 89/336/EWG entspricht. Diese Herstellererklärung hat für folgende PMV-Stellungsregler-Serien Gültigkeit: P5, EP5, F5. F Déclaration de fabricant au sens dela dir
Flowserve Corporation has established industry leadership in the design and manufacture of its products. When properly selected, this Flowserve product is designed to perform its intended function safely during its useful life. However, the purchaser or user of Flowserve products should be aware that Flowserve products might be used
Amway Business Owners (ABOs) at a 12% and above level for LD bonuses EP1-EP5. 2. How is the Earning Period (EP) determined for each ABO? ABOs starting the Performance Year (PY) 2020/21 at a minimum of Founders Platinum level are eligible for EP5. ABOs whose highest
- Engineering (hydraulic calculations, design, Flowserve) - Delivery of two new pumps, with modified hydraulics, as per API 610, 12th edition, ATEX certified (Flowserve) - Delivery of two API 53B/23 seal support systems (Flowserve) - Delivery of two dual, metal bellow mechanical seals (Flowserve) - Delivery of new couplings (John Crane)
Flowserve Pump Division to provide sound and all necessary information the content of this manual may appear insufficient and is not guaranteed by Flowserve as to its completeness or accuracy. Flowserve manufactures products to exacting International Quality Management System Standards as certified and audited by external Quality Assurance .
In 2004 Flowserve Pump Division (FPD) acquired Thompsons, Kelly & Lewis Pty. Ltd. (TKL) which was formed in 1987 by the merger of two long-established pump companies, Thompsons at Castlemaine (Vic) and Kelly & Lewis in Melbourne. FPD is a division of Flowserve Corporation of the USA, a global company manufacturing centrifugal
Vendor: Flowserve Pump Division 2300 E. Vernon Ave. Vernon, CA 90058 Vendor Contact: Mr. David Gobbi Quality Assurance Manager E-mail: dgobbi@flowserve.com Phone: (980) 722-6770 Nuclear Industry Activity: Flowserve Pump Division, located at 2300 E. Vernon Ave. Vernon, CA, is an American Society of Mechanical Engineers (ASME)
Flowserve Corporation Pump Division Via Rossini 90/92 20033 Desio (Milan), Italy Telephone: 39 0362 6121 Telefax: 39 0362 303396 Latin America and Caribbean Flowserve Corporation Pump Division 6840 Wynnwood Lane Houston, Texas 77008 USA Telephone: 1 713 803 4434 Telefax: 1 713 803 4497 Asia Pacific Flowserve Pte. Ltd. Pump Division 200 Pandan .
astrophysics-and-cosmology Professional and/or Statutory Regulatory Body accreditations Institute of Physics (recognised full accreditation pending 2018) Quality Assurance Agency Framework for Higher Education Qualifications (FHEQ) Level Level 4,5,6 Institute of Physics Core Curriculum specification This course specification provides a summary of the main features of the course, identifies the .
