FAST, PRECISE, STRAIGHT CUTS - Bora Tool

Bora WTX Clamp Edge Saw GuideBora Saw PlateBora Rip GuideFAST, PRECISE, STRAIGHT CUTSMADE EASY WITH THE BORA SAW GUIDE SYSTEMwww.boratool.com1

THE BEST TOOL FORMAKING STRAIGHTCUTS WITH EASEWhat’s the Most Important Stepin Any Project?It’s no exaggeration to say that making accurate cutsis the key to any successful project. Without clean,precise cuts, assembly is more difficult, strengthand stability are compromised and the appearanceof the finished project will suffer. Fortunatelypower tools such as a portable circular saw greatlyimproves the chance for success. But to ensure thebest results you need the Bora Saw Guide System.It’s the simple, fast and precise guide for ripping orcrosscutting lumber or sheet material.50” WTX Clamp EdgeSaw GuideAvoid These Common ProblemsUsing a circular saw freehand is a challenge, especially when making longcuts. The saw can drift and the blade can bind. As a result the cut materialis left with an uneven, crooked or burned edge. It’s hard on both the powersaw and the blade. Even worse, crude or unprofessional cuts give you apoor fit and finish. The proper tools are essential for getting clean cuts –and avoiding expensive mistakes.Makes Every Craftsman BetterThe Bora Saw Guide System provides a complete solution for making true,accurate cuts with virtually any circular saw. The quick-adjusting, lightweightWTX Clamp Edge Saw Guide, the smooth-sliding Saw Plate, and the versatileRip Guide deliver exceptional convenience and efficiency. No workshop,whether professional or DYI, is complete without the Bora Saw Guide System.Standard T-Slot fits½”-20 bolt and is perfectfor jigs, fixtures andaccessories Up to 50” of cutting capacity Self-clamping Rigid aluminum extrusion – superiorstrength with no flexingNew, patented designeliminates the internalclamping rod, increasingthe durability comparedto other Clamp Edgemodels.Tough and Mobile, Perfect for Any Job SiteContractors and tradesmen will find the Clamp Edge and Rip Guideindispensible at a job site and in their workshop. The WTX Clamp Edge iscompact, portable, sets up fast, holds tight and has a quick-release clampingmechanism. Add the optional extension and you have the perfect fence forcutting 8-foot sheets of plywood, MDF, OSB and other sheet material. TheWTX Clamp Edge Saw Guide will help you build faster and better. Works with a circular saw, jig saw,router and many other tools Optional extensions increasecutting capacity to 100”2www.boratool.comwww.boratool.com3

The BoraRip Guide:For MakingMultiple CutsUp To 24” Wide Saw Plate works with rightor left-handed saws50” WTX Clamp EdgeSaw Guide Saw Plate ensures precise cutsend-to-endLots of projects require multiplepieces cut exactly the same size.Measuring, marking, setting up aguide and cutting each one can taketime. But not if you use the BoraRip Guide. Set it once to any sizeup to 24” and the Rip Guide makesrepetitive cuts easily without havingto reset the guide or marking newpencil guidelines. The Rip Guide ismade of the same high-strengthextruded aluminum as the ClampEdge for strength and durability. Aspecially designed channel securesthe Saw Plate in the correct position.A comfortable molded handleprovides a sure grip for pushing theGuide evenly across the materialyou’re ripping. The blade aligns withan integrated blade guide on theSaw Plate to ensure accuracy. TheRip Guide, together with the ClampEdge forms a complete, easy-to-usesystem for making cross cuts andripping wood or other sheet goods. Easy to mount to any circular saw Rip Guide adjusts to 24” wideThe Bora WTX Clamp Edge Saw GuideFor Making Cuts Up To 100” LongThe WTX Clamp Edge is made of a high-strength, extruded aluminum alloy thatprovides excellent dimensional stability. It’s also lightweight, durable and corrosionresistant. The Clamp Edge provides a straight and true edge for making cuts up to50” long. Add the optional extension and now you can reach up to 100” inches incutting length – perfect for standard 8-foot sheet material such as plywood.50” WTX Clamp Edge withSaw Plate attachedLocking the Clamp Edge in place is a snap – literally. Set it in position; adjust theclamp end; then lock it in place by pushing the handle down. It’s that simple. Push acircular saw, router, sabre saw, marking tool – virtually any tool – along the ClampEdge and it won’t budge.The Bora Saw Plate Makes theWTX Clamp Edge Saw Guide Even BetterAdd the Saw Plate and you have a foolproof system for preventing a saw fromwandering. Cuts are perfectly square, or if the blade is set at an angle there’s nodeviation from one end of the cut to the other. It works with eithera right-hand or left-hand saw. Saws are easy to mount with twoadjustable screws at the front of the plate, plus an adjustablemetal thumbscrew that secures the saw at a third pointon the base. The underside features an adjustablechannel that fits not only the Clamp Edge, but alsoany straight edge up to 3 ½” wide.Blade indicator lines upwith the saw blade.SWITCH EASILY BETWEENMAKING RIP CUTS ANDCROSS CUTSThe Bora Saw Plate is engineered to slide on topof the Bora WTX Clamp Edge Saw Guide or attachto the Rip Handle without removing your saw.4www.boratool.comBora Rip Guidewww.boratool.com5

Tips and TechniquesUsing the Bora WTX Clamp Edge Saw GuidePlace the Clamp Edge on the material you’re cutting with the handle end againstthe edge. On the opposite edge pinch the sliding adjustable clamp end to move itinto a snug position. Push the handle down to lock it in position.Bora Saw Guide SystemWTX Family24” WTX Clamp Edge36” WTX Clamp EdgeWhat Can You Do With theBora Saw Guide System?50” WTX Clamp EdgeSet the Saw Blade DepthWith the saw unplugged, check the depth of the blade against the edge of thematerial and adjust to approximately 1/2” below the board. Tighten the blade inthat position.Support the Material You’re CuttingSupport your work near the cut line across the entire length of the cut so it’s leveland stable and doesn’t buckle under the weight of the saw. This helps prevent theblade from getting pinched, which can cause binding or kickback.WTX Extensions50” WTX Extension25” WTX ExtensionNice and EasyPush your saw against the Clamp Edge with a continuous smooth motion. Let thecut piece fall freely.For 5-foot pieces of sheet goods combine the36” WTX Clamp Edge and the 25” WTX ExtensionWTX AccessoriesUsing the Bora Saw PlateA circular saw is fastened to the Saw Plate by the set screws in the two clampsat the front of Saw Plate. An additional spring clamp secures the circular saw tothe Saw Plate. With the saw securely fastened to the Saw Plate, slide it into thematching channels on the Clamp Edge. With the saw unplugged, check and adjustthe blade’s depth as necessary.AuxiliaryClampsSaw PlateAn even, continuous push enables a clean, precise cut with no chance of the sawdrifting out of position.Using the Bora Rip GuideRip cuts can be made easily with the Rip Guide by following these simplesteps. Make sure the material you are cutting is stable and won’t move as youapply pressure to the edge with the Rip Guide. Bench dawgs, clamps or eventemporarily nailing the material to a work surface can prevent the material frommoving during cutting.Unplug the saw and mount it to the Saw Plate. Check blade depth against materialto be cut and adjust if necessary. Place the Saw Plate into the channel on the RipHandle. Set the desired width by aligning the guide marker at the front of the SawPlate to the guide’s ruler. Tighten the Saw Plate in place.Position the Rip Guide so the Rip Handle fits snuggly against the edge of thematerial to be cut. Apply even, continuous pressure against the edge of thematerial while you push the saw to maintain a true edge for subsequent cuts.Whenever you use power tools always work safe, wear safety glasses and the properclothing, and follow all safety precautions provided by your tool’s ip GuideRip GuideHandleBora Saw Guide SystemVirtually everything you create withwood will require some straight cuts.The Bora Saw Guide System willmake all those cuts easier and moreprofessional, no matter what yourlevel of skill. The Bora Saw GuideSystem is great for making a Wine Rack Night Stand Jewelry Box Crib Keepsake Box Collectibles Cabinet Flag Case Entryway Organizer Spice Cabinet Shelves Butcher Block Picture Frames Clock Case Workbench Step Stool Storage Boxes Knife Rack Media Center Cutting Board Pedestal Tables Side Chair Trestle Table Coffee Table Children’s Toys Console Table Adirondack Chairs Side Table Picnic Table Cabinet Birdhouse EntertainmentCenter Potting Bench Dresser Garden StorageBench Bookcase Firewood Rack CD Cabinet Flowerboxes Desk Planter Boxes Printer Stand Shed Bench Dog House Hope ChestWTX Clamp Edge Saw GuideAccessories543100100” WTX Clamp Edge(50” WTX Clamp Edge 50” Extension)542010Extension Connectors (set of 2)54305050” WTX Clamp Edge542006Saw Plate54303636” WTX Clamp Edge542007Rip Guide Handle(Extrusion plus handle)54302424” WTX Clamp Edge542008Rip Guide542002WTX Auxiliary ClampsWTX Extensions54206050” WTX Extension with connectors54203525” WTX Extension with connectors54205050” WTX Extension (track only)54202525” WTX Extension (track only)www.boratool.com7

Where to Get theBora Saw Guide SystemThe Bora Saw Guide System isavailable at leading retailers,home centers, specialty tool andonline retailers. To find out whereto purchase Bora products nearyou visit www.boratool.comAffinity Tool Works is a global toolmanufacturer serving contractors,do-it-yourselfers, remodelers andwoodworkers. Additional brandsmanufactured by Affinity Tool Worksinclude Portamate and HTC Products. 2015 Affinity Tool Works, LLC8www.boratool.com

The Bora. Rip Guide: For Making Multiple Cuts Up To 24” Wide. Lots of projects require multiple . pieces cut exactly the same size. Measuring, marking, setting up a guide and cutting each one can take time. But not if you use the Bora Rip Guide. Set it once to any size up to 24” and the Rip Guide makes repetitive cuts easily without having