R ELECTRIC PRESSURE WASHER - Snow Joe
ROPERATOR’S MANUALA Division of Snow Joe , LLCELECTRIC PRESSURE WASHER2300 PSI MAX* 1.48 GPM MAX* 13-AMPModel SPX3500Form No. SJ-SPX3500-880E-MR6IMPORTANT! Stay alert – Watch what you are doing. Use commonsense. Do not operate the pressure washer when you aretired, or under the influence of alcohol or drugs.Safety InstructionsAll Operators Must Read TheseInstructions Before Use Do not overreach – Keep proper footing and balance atall times. Avoid unintentional starting – Do not carry a pluggedin machine with your finger on the trigger. Make sure theswitch is off before plugging in the machine.mWARNING! This indicates a hazardous situation, which, Do not abuse the cord – Never carry the machine by thecord or yank the cord to disconnect it from the receptacle.Keep the cord away from heat, oil, and sharp edges.if not avoided, could result in death or serious injury.mCAUTION! This indicates a hazardous situation, which,if not avoided, could result in minor or moderate injury. Use safety glasses – Also use safety footwear, snug-fittingclothing, protective gloves, hearing and head protection.mDANGER! This indicates a hazardous situation, which, Check the water temperature – This pressure washer isnot meant to pump hot water. NEVER connect it to a hotwater supply as it will significantly reduce the life of thepump.if not followed, will result in death or serious injury.General SafetymWARNING! This appliance is not intended for use Store indoors – NEVER store the pressure washeroutdoors or where it could freeze. The pump could beseriously damaged.by children or by unassisted, unsupervised persons whosephysical, sensory or mental capabilities prevent them fromusing it safely. Children should be supervised to ensure thatthey do not play with the appliance. Ground Fault Circuit Interrupter (GFCI) – This productis provided with a ground fault circuit interrupter built intothe power cord plug. If replacement of the plug or cord isneeded, use only identical replacement parts.Before starting up your machine, please check it carefully forany defects. If you find any, do not start up your machine.Contact your authorized Snow Joe Sun Joe dealer orcall the Snow Joe Sun Joe customer service center at1-866-SNOWJOE (1-866-766-9563). Inspect electrical cords – The insulation of the power cordshould be perfectly intact. If the power cord is damaged orshows any signs of wear or tear, do not use the pressurewasher. Contact your authorized Snow Joe Sun Joe dealer or call the Snow Joe Sun Joe customer servicecenter at 1-866-SNOWJOE (1-866-766-9563).mWARNING! When using the pressure washer, basicsafety precautions should always be followed to reduce therisk of fire, electric shock, and personal injury. These include:mWARNING! Do not use this appliance without readingthis instruction manual. Know your product – Know how to stop the machine andbleed pressure quickly. Thoroughly familiarize yourself withthe controls.mWARNING! This appliance has been designed foruse with cleaning agents that are recommended by themanufacturer. The use of other cleaning agents or chemicalsmay adversely affect the safety of the appliance. Keep bystanders away – All visitors and pets should bekept a safe distance away from the work area. Use the right product – Do not use this machine for anyjob except that for which it is intended.mWARNING! Do not use the appliance within range of Dress properly – Do not wear loose clothing or jewelry.They can get caught in moving parts. Protective rubbergloves and non-slip footwear are recommended whenworking outdoors.persons unless they are wearing protective clothing.mWARNING! High-pressure jets can be dangerous ifsubject to misuse. The jet must not be directed at persons,pets, live electrical equipment, or the appliance itself. mCAUTION! – Exercise caution to avoid slipping or falling.Wear protective footwear that will protect your feet andimprove your footing on slippery surfaces. 2020 by Snow Joe , LLCAll rights reserved. Original instructions. Do not direct the jet at yourself or others in order to cleanclothes or footwear.1SAVE THESE INSTRUCTIONS
Electrical Safety Risk of explosion – Do not spray flammable liquids. Disconnect the tool – Disconnect from the electrical powersupply before performing any maintenance task.ATTENTION: If there are problems with the electrical Keep children away – This high-pressure electricpower washer must not be used by children or untrainedpersonnel.MAINS, short voltage drops may appear when starting theequipment. This can, in turn, influence other equipment(e.g. cause a lamp to blink). If the MAINS-IMPEDANCE Zmax 0.335 OHM, such disturbances are not expected. (If yourequire assistance, contact your local supply authority forfurther information.) To ensure appliance safety, use only original replacementparts from the manufacturer or those approved by themanufacturer.mWARNING! Water that has flowed through backflowmWARNING! Electrical Shock Hazard – Before startingup your machine, please check it carefully for any defects. Ifyou find any, do not start up your machine and contact yourdistributor.preventers is considered to be non-potable.mWARNING! During cleaning, maintenance or whenreplacing parts, the machine must be disconnected from itspower source by removing the plug from the socket outlet.The following should be observed when connecting thehigh-pressure electric power washer to the electric supply:mWARNING! High-pressure hoses, fittings, and The electric supply connection should be performed by aqualified person.couplings are important for the safe operation of the appliance.Use only hoses, fittings, and couplings recommended by themanufacturer. The electric supply to this appliance should include eithera residual current device that will interrupt the supply if theleakage current to the earth exceeds 30 mA for 30 ms or adevice that will interrupt the earth circuit (GFCI). Check for damaged parts – Do not use the appliance ifthe supply cord or other important parts of the applianceare damaged (e.g. safety devices, high-pressure hoses,trigger gun).IMPORTANT: Only use water without any impurities.If there is a risk of running sand into the inlet water (i.e. fromyour own well), an additional filter should be installed.mWARNING! If an extension cord is used, the plug andsocket must be of watertight construction.Grounding InstructionmWARNING! Inadequate extension cords can beThis product must be grounded. If it should malfunction orbreakdown, grounding provides a path of least resistancefor electric current to reduce the risk of electric shock. Thisunit is equipped with a cord having an equipment-groundingconductor and a grounding plug. The plug must be pluggedinto an appropriate outlet that is properly installed andgrounded in accordance with all local codes and ordinances.dangerous. This high-pressure electric power washer must not be usedat temperatures below 32ºF (0 C).mWARNING! Power cords on drums should always becompletely unwound to prevent the cord from overheating. Power cord connections should be kept dry and off theground.mDANGER! Improper connection of the equipmentgrounded conductor can result in a risk of electrocution. Checkwith a qualified electrician or service personnel if you are indoubt as to whether the outlet is properly grounded. Do notmodify the plug provided with the unit. If it will not fit the outlet,have a proper outlet installed by a qualified electrician. Do notuse any type of adapter with this unit. If the power cord is damaged, do not use the appliance.Contact your authorized Snow Joe Sun Joe dealer orcall the Snow Joe Sun Joe customer service center at1-866-SNOWJOE (1-866-766-9563). Keep the machine on a stable, flat surface during operation,handling, transportation, and storage. Sudden overturn ofthe machine can cause bodily injury.Safety Devices In the event of an accident or breakdown, switch off themachine immediately. (If contact with detergent occurs,rinse with an abundance of clean water.)The unloader valve can reduce pressure if it exceeds presetvalues. The spray gun features a locking device. When the lockis activated, the spray gun cannot be operated.1. Thermal sensor – A thermal sensor protects the motoragainst overloading. If the thermal sensor is activated andthe power is cut off, wait for a while until the motor is cooland restart the unit.2
2. Ground fault circuit interrupter (GFCI) protection – Thispressure washer is provided with a ground-fault circuitinterrupter (GFCI) built into the plug of the power-supplycord. This device provides additional protection from therisk of electric shock. Should replacement of the plug orcord become necessary, use only identical replacementparts that include GFCI protection.Table 1. Method of Securing Extension CordCord set3. It is not recommended to use an extension cord withthis pressure washer. The unit comes standard with a35 ft GFCI power cord. Using an extension cord maycause a drop in line voltage resulting in loss of power andoverheating.(A) Tie cord as shown4. Use only 3-wire extension cord that has 3-pronggrounding type plug for the product. Use only extensioncords that are intended for outdoor use. These extensioncords are identified by marking "Acceptable for use withoutdoor appliance; store indoors while not in use". Useonly extension cord having an electrical rating not lessthan the rating of the product. Do not use damagedextension cords. Examine extension cord before usingand replace if damaged. Do not abuse extension cord anddo not yank on any cord to disconnect. Keep cord awayfrom heat and sharp edges. Always disconnect extensioncord from the receptacle before disconnecting the productfrom the extension cord.m(B) Connect plug and receptacle6. Do not abuse the cord. Never pull the pressure washerby the cord or yank the cord to disconnect it from thereceptacle. Keep the cord away from heat, oil, and sharpedges.Risk of electrocution Inspect cord before using. Do not use if cord is damaged.mWARNINGAppliance cord Keep all connections dry and off the ground. Do not touch plug with wet hands. Keep cord away from heat and sharp edges.Electric shock may cause SEVERE INJURY orDEATH. Heed these warnings: Do not spray electrical apparatus and wiring. Do not allow any part of the electric pressure washerto make contact with water while it is in operation. Ifthe appliance becomes wet while turned off, wipe drybefore starting.Risk of explosion Do not spray flammable liquids. Do not use acids, bases, solvents, or any flammablematerial in this product. These substances can causephysical injuries to the operator and irreversible damage tothe machine. Do not use an extension cord over 25 ft. Thepressure washer comes equipped with a 35 ft powercable. Combined cord length must not exceed 60 ft.Any extension cord must be 14-gauge (or heavier) tosafely power the pressure washer.Additional safety instructions Do not touch the appliance or its plug with wet handsor while standing in water. Wearing rubber bootsoffers some protection. High-pressure: keep clear of nozzle. Injection hazard: equipment can cause serious injury if thespray penetrates the skin.EXTENSION CORD CHART Do not point the gun at anyone or at any part of the body.Cord Length:25 ft (7.6 m)Min. Wire Gauge (A.W.G.):14 In case of skin penetration, seek medical aid immediately. Before servicing, cleaning, or removing any parts, shut offthe power and relieve pressure. This machine is not suitable for connection to the potablewater mains.mWARNING! To reduce the risk of electrocution, keepall connections dry and off the ground. Do not touch plug withwet hand.5. To prevent the appliance cord from disconnecting from theextension cord during operation, make a knot with the twocords as shown in Table 1.3
Product DescriptionPurpose This electric high pressure washer is intended for residentialuse only. It is designed for medium-to-heavy duty cleaningjobs on boats, motorcycles, RV’s, ATV’s, trailers, decks,barbecues, siding, patio furniture, and more.Areas of application Never use the machine in potentially explosive areas underany circumstances! The operating temperature must be between 32ºF (0ºC) and104ºF (40ºC). The machine consists of an assembly with a pump, whichis encased in a shock-absorbing housing. To provide theoperator with an optimal working position, the machine isequipped with a spray wand and a non-slip handle grip,whose shape and configuration comply with applicableregulations. Do not cover or modify the spray wand or the spray nozzlein any way. The high-pressure electric power washer is designed to beused with cold or lukewarm water; higher temperatures candamage the pump. Do not use water that is dirty, gritty, or contains anychemical products, as such impurities could impairoperation and shorten the life of the machine.4
Safety SymbolsThe following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow allinstructions on the machine before attempting to assemble and operate.SymbolsDescriptionsSymbolsDescriptionsREAD THE OPERATOR'SMANUAL(S) – Read, understand,and follow all instructions in theuser manual(s) before attemptingto assemble and operate.WARNING! Electrical shock hazard.SAFETY ALERT – Indicates aprecaution, a warning, or a danger.WARNING! Do not expose theunit to rain or wet conditions.Keep dry.WEAR EYE AND HEARINGPROTECTION – For protectionagainst injury, wear ear defendersand safety goggles.To reduce the risk of injury, usermust keep all bystanders at least49 ft (15 m) away.Wear safety gloves duringuse to protect hands.Wear non-slip footwear that willprotect your feet and improve yourfooting on slippery surfaces.Store indoors. Never store thepressure washer outdoors.If the pump freezes, permanentdamage may result.Machine not suitable for connectionto the potable water mains.WARNING! Turn the machine OFFand disconnect it from the powersupply before inspecting, cleaning,changing accessories, or conductingany other maintenance task.Always keep the power cableaway from heat sources, oils, orsharp edges. Immediately removeplug from the mains if the cable isdamaged, frayed, or entangled.5
Know Your Electric Pressure WasherRead the owner’s manual and safety rules carefully before operating the pressure washer. Compare the illustration below tothe unit in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for 123242118260º1415178327164285761. Handle10. Soap Quick-Connect nozzle (black)19. Nozzle storage board2. On/Off switch11. 40º Quick-Connect nozzle (gray)20. High-pressure hose3. Detergent dial12. 25º Quick-Connect nozzle (green)21. High-pressure hose holder4. Garden hose adapter/connection13. 15º Quick-Connect nozzle (yellow)22. Trigger gun5. Spray wand protector14. 0º Quick-Connect nozzle (orange)23. Safety lock6. Water inlet15. Needle clean-out tool24. Trigger7. Wheel (2)16. Water outlet/high-pressure hoseconnection25. High-pressure hose connection17. Detergent tank27. Spray wand8. Power cord with GFCI9. Cord holder (2)18. Detergent tank capTechnical Data26. Trigger gun holder28. Quick-connector collarRated Voltage. 120 V 60 HzMax Pressure*. 2300 PSIMotor. 13-ampRated Pressure. 2000 PSIMax Water Inlet Temperature. 104ºF/40ºCDetergent Tank Capacity. 40.6 fl oz (1.2 l)Max Water Inlet Pressure . 0.7 MPaHose Length. 20 ft (6 m)Max Flow*. 1.48 GPMPower Cord Length. 35 ft (10.7 m)Rated Flow. 1.09 GPMWeight. 36.8 lbs (16.7 kg)* Max rating per CSA test standards. Maximum internal pressure is 2300 PSI and flow is 1.48 GPM.Under typical load, working pressure is 2000 PSI and flow is 1.09 GPM.6
UnpackingFig. 1Carton Contents Electric pressure washerHandleFix with 44.8 x 16 screws Handle High-pressure hose holder Nozzle storage board Spray wand protector Trigger gun holder 4.8 x 20 screws (2) 4.8 x 16 screws (9)Pressure hose holder Spray wand2. Slide the handle with high-pressure hose assembly inposition on the top of the pressure washer, fixed with two4.8 x 20 screws and two 4.8 x 16 screws as shown(Fig. 2). Trigger gun Needle clean-out tool (included with manual packet) Five (5) Quick-Connect nozzles (0º, 15º, 25º, 40º and Soap) High-pressure hoseFig. 2 Garden hose adapter (female coupler) Manuals with registration cardHandle assembly1. Carefully remove the pressure washer and check to seethat all of the above items are supplied.2. Inspect the product carefully to make sure no breakage ordamage occurred during shipping. If you find damaged ormissing parts, DO NOT return the unit to the store. Pleasecall the Snow Joe Sun Joe customer service center at1-866-SNOWJOE (1-866-766-9563).Fix with 4.8 x 16screwsNOTE: Do not discard the shipping carton and packagingmaterial until you are ready to use your new electricpressure washer. The packaging is made of recyclablematerials. Properly dispose of these materials inaccordance with local regulations.Fix with 4.8x 20 screwsIMPORTANT! The equipment and packaging material are nottoys. Do not let children play with plastic bags, foils, or smallparts. These items can be swallowed and pose a suffocationrisk!3. Put on the nozzle storage board in position and securewith two 4.8 x 16 screws (Fig. 3).mWARNING! Do not connect to power supply untilassembly is complete. Failure to comply could result inaccidental starting and possible serious personal injury.AssemblyTools required: Phillips head screwdriver1. Slide the high-pressure hose holder in position on thehandle, fix with four 4.8 x 16 screws provided (Fig. 1).7
Fig. 3Fig. 5Nozzlestorage boardFix with 4.8x 16 screws4.8 x 16 screwSlotTab6. Fit the spray wand into the trigger gun and rotate it untilthe two parts are completely locked (Fig. 6).4. Slide the trigger gun holder in position (Fig. 4).Fig. 4Fig. 6Trigger gunTrigger gun holderSpray wand7. Connect the high-pressure hose to the trigger gun (Fig. 7).Fig. 75. To assemble the spray wand protector, first snap the tabinto the slot located at the bottom left side of the unit, andthen secure it in place with one 4.8 x 16 screw (Fig. 5).Trigger gunHigh-pressure hose8. Connect the other end of high-pressure hose to the wateroutlet on the washer (Fig. 8).8
Fig. 8Fig. 10Connect to water supplyWater outletGarden hoseHigh-pressurehosemWARNING! Do not connect to potable water system.mWARNING! If connection is made to a potable watermWARNING! Keep hose away from sharp objects.system, the system shall be protected against backflowmWARNING! The intake water temperature must notBursting hoses may cause injury. Examine hoses regularly andreplace if damaged. Do not attempt to mend a damaged hose.exceed 104ºF/40ºC. The water supply must not exceed0.7 MPa.9. Connect the garden hose adapter (female coupler) tothe water inlet of the pressure washer, then thread yourgarden hose (male end) into the garden hose adapter(Fig. 9). The garden hose must have an internal diameterof at least 13 mm (1/2 in.) and must be reinforced. Thewater supply must be at least equal to the washer deliverycapacity.mCAUTION! The washer must only be used with cleanwater; use of unfiltered water containing corrosive chemicalswill damage the washer.OperationNOTE: The machine is not suitable for connection to thepotable water main.Using the Pressure WashermIMPORTANT! This pressure washer is equipped withFig. 9a micro-switch sensitive to water flow. This Total Stop System(TSS) senses water flow in the pump. When the trigger isreleased, water stops flowing through the pump. The TSS thenautomatically turns the motor off to protect the pump fromoverheating, thus saving energy and prolonging pump life.This end towater inlet1. Position the washer as CLOSE as possible to the watersupply.2. The washer must be used on a secure and stable surfacein a standing, upright position (Fig. 11).Garden hose(male end)Fig. 11Garden hoseWater inlet10. Attach garden hose to water supply (Fig. 10).9
3. Make sure the unit is switched off before plugging the unitinto the power outlet.Fig. 144. Check that the electrical supply voltage and frequency(Volt/Hz) correspond to those specified on the rating plate.If the power supply is correct, you may now plug thepressure washer into the power outlet (Fig. 12).Fig. 12ON/OFF switchResetTSEREPower lightindicatorTEST8. When re-starting the motor, always keep the triggerpressed.GFCINOTE: The motor only runs when the trigger is operatedand shuts off when the trigger is released.NOTE: The GFCI may need to be reset when first pluggedinto the electric outlet. Press the "Reset" button untilthe power light indicator on the GFCI illuminates whenplugged in.5. Turn the water supply tap on completely.6. Make sure the safety lock is down and in its originalposition (Fig. 13), then press the trigger for a few secondsuntil water flow is steady. This will allow air to escape anddischarge any residual pressure in the hose.Fig. 13SlotUsing NozzlesBefore beginning any cleaning task, determine the best nozzlefor the job. Each of the nozzles has a different spray pattern.The nozzle patterns are 40 (for gentle cleaning), 25 (for allpurpose cleaning), 15 (for tough jobs), 0 (for spot cleaningor hard-to-reach areas) and the Soap nozzle (for detergentapplication).mCAUTION! NEVER change nozzles without locking thesafety lock on the trigger handle.mWARNING! High-pressure jets can be dangerous ifsubject to misuse. The jet must not be directed at persons,pets, live electrical equipment, or the appliance itself.This electric pressure washer is equipped with five (5) QuickConnect nozzles that easily snap onto the Quick-Connectcollar of the spray wand.To connect a nozzle to the spray wand:1. Turn off the pressure washer and shut off the water supply.Pull the trigger to release water pressure.Safety lock2. Engage the safety lock on the trigger handle by pushingup on the safety lock until it clicks into the slot (Fig. 15).Trigger7. Turn the ON/OFF switch to the ON (I) position to start thepressure washer (Fig. 14).10
Working with DetergentsFig. 15SlotSafety lock3. Snap the desired nozzle onto the Quick-Connect collaruntil it clicks into place (Fig. 16).Fig. 16Spray wand quickconnect collarNozzleWhen cleaning with the pressure washer, some cleaning taskscan be solved with water alone, but for most tasks cleaningwith detergent allows for more effective dirt removal.mWARNING! Use only detergents specifically designedfor use with pressure washers, such as Sun Joe HOUSE DECK WASH (SPX-HDC1G), Sun Joe SNOW FOAM AUTOWASH (SPX-FCS1G), or Sun Joe HEAVY DUTY CLEANER(SPX-APC1G). DO NOT USE household detergents, acids,alkaline solutions, bleaches, solvents, flammable material, orindustrial grade solutions. These could damage the pressurewasher. Many detergents may require mixing prior to use.Prepare the cleaning solution as instructed on the solutionbottle.mWARNING! When being used with detergent, makesure to use the black soap quick-nozzle.1. Remove the detergent tank cap with suction tube. Gentlypull the detergent tank out of its storage position(Figs. 17 – 18).“Click”Fig. 17Detergent tankcap withsuction tubeTo disconnect a nozzle from the spray wand once the cleaningjob is complete:4. Turn off the pressure washer and shut off the water supply.Pull the trigger to release water pressure.Detergenttank5. Engage the safety lock on the trigger handle by pushingup on the safety lock until it clicks into the slot (Fig. 12).6. Remove the nozzle by placing your hand over the nozzlewhile pulling back on the Quick-Connect collar.mWARNING! Do not make changes to the nozzle whilethe trigger is engaged. Doing so could result in damage to thepressure washer or injury to the user.Fig. 18Detergenttank11
8. When finished using the pressure washer, you must firstdrain and rinse the detergent tank. Run the pressurewasher until all of the soap is drained from the detergenttank.2. Fill the tank or mix as recommended by detergentinstructions (Fig. 19), and replace it back on the unit.Secure the cap with suction tube back into place.Fig. 19mCAUTION! Failure to follow these cleaning instructionswill cause the injection system to become clogged andinoperable.Rinsing with the Pressure Washer1. Turn off the pressure washer and shut off the water supply.2. Pull the trigger to release water pressure.Detergent tank3. Engage the safety lock on the trigger handle by pushingup on the safety lock until it clicks into the slot (Fig. 13).Detergentfor pressurewasher4. Remove the soap nozzle by placing your hand over thenozzle while pulling back on the quick-connect collar.5. Select the right nozzle for the job (Fig. 21):3. Install the soap nozzle (black) on the spray wand (Fig. 16).4. Turn on the pressure washer. Pull the trigger to operate theunit. The liquid detergent will automatically mix with waterand be discharged through the nozzle.Fig. 21mCAUTION! Always test the detergent in aninconspicuous area before use.5. Turn the detergent dial to adjust the suction volume of thedetergent solution (Fig. 20).0ºFig. 2015º25º40ºSOAPDetergentdialI) The 0º intense-jet nozzle (orange) is an extremelypowerful nozzle that delivers a high-pressure, pencilpoint jet stream. It is used to cut heavy dirt depositsin a small, concentrated area. It is ideal for dissolvingstubborn substances, like tar and grease spots onconcrete, or for removing caked mud from equipment.Use this nozzle to clean hard-to-reach areas includingthe facades of 2-story buildings or the undersides oflawn mowers and tractors.6. Apply detergent from the bottom to the top of the drysurface to be cleaned.NOTE: Wetting the surface first is not recommended as itdilutes the detergent and reduces its cleaning ability.NOTE: Care should be used when choosing theright nozzle to avoid permanently gouging wood ordamaging fragile surfaces.7. Allow the detergent to remain on the surface for a shorttime before rinsing. Do not allow the detergent to dry onthe surface.II) Use the 15º fan-tip nozzle (yellow) for intense cleaningjobs on hard surfaces. Applications include strippingpaint, removing oil stains, grease, heavy mildew stains,and rust from steel. This nozzle should only be used inareas that can withstand the high-pressure from thisnozzle.mCAUTION! Damage may occur to painted surfaces ifthe detergent is allowed to dry on the surface. Wash and rinsea small section at a time. Avoid working on hot surfaces or indirect sunlight.III) Use the 25º fan-tip nozzle (green) to clean home siding,brick patios, wood decks, driveways, or sidewalks.When using this nozzle, test a small area first to avoidsurface damage.12
IV) Use the 40º wide-spray tip nozzle (gray) to clean itemssuch as cars, trucks, boats, patio furniture, or lawnequipment. Store the pressure washer indoors in a dry, covered areawhere it is not subject to adverse weather conditions. It is important to store this product in a frost-free area.V) Use the Soap nozzle (black) for low-pressure detergentapplication to clean equipment, remove mildew andoxidation stains from houses, clean bricks or degreasegrimy surfaces. Always empty water from the hoses, the pump, and thedetergent tank (if using) before storing.mCAUTION! The use of a pump protector isrecommended to prevent cold weather damage during storageover the winter months.NOTE: When using detergent, make sure to install thecorrect Soap nozzle (black). All of the other colorednozzles will not work for detergent application.Winterizing long-term storage6. Start at the top of the area to be rinsed and work your waydown, making sure to overlap your strokes.If you must store your pressure washer in a location wherethe temperature falls below 32ºF (0ºC), you can minimize thechance of damage to your machine by utilizing the followingprocedure:mIMPORTANT! NEVER USE: Bleach, chlorine products, and other corrosive chemicals Liquids containing solvents (e.g. paint thinners, gasoline,oils). Disconnect all water connections. Turn on the pressure washer for a few seconds until theremaining water in the pump exits. Turn off immediately. Tri-sodium phosphate products Ammonia products Do not allow the high-pressure hose to become kinked. Acid-based products Store the machine and accessories in a room that doesnot reach freezing temperatures.These chemicals will harm the unit and will damage thecleaning surface. Do not store near a furnace or other sources of heat thatmay dry out the pump seals.Shutting down Operate the pressure washer with non-corrosive/non-toxicanti-freeze, a pump saver, or a pump protector beforestoring for the winter.1. Turn the switch to the OFF (0) position and unplug thepower cord from the outlet.2. Turn off the water source.mWARNING! Before reusing, completely flush the unit3. Hold the trigger to release water pressure.out with clear water. Anti-freeze products can damagepaintwork, so you must ensure there is no anti-freeze left in thesystem before using it again.4. Disconnect the garden hose from the water inlet onthe unit.5. Disconnect the high-pressure hose connection on thetrigger gun handle.MaintenancemCAUTION! Before working on the pressure washer,6. Release the trigger and engage the gun safety lock.mWARNING! Turn off the water supply and squeeze thedisconnect the pl
If the power cord is damaged, do not use the appliance. Contact your authorized Snow Joe Sun Joe dealer or call the Snow Joe Sun Joe customer service center at 1-866-SNOWJOE (1-866-766-9563). Keep the machine on a stable, flat surface during operation,
Snow Clearing: The moving of accumulated snow from the surface of a defined service area. Synonyms: Snowplowing, or Snow Pushing. Snow Dump: A defined area to store large amounts of snow from one or many sites. Synonyms: Snow Field, Snow Farm. Snow Hauling: Part of the Snow Removal process, it is the act of transporting snow and other winter
snow event is not necessarily a single large snow storm. A snow event can be a series of storms that result in additional snow loads . on a building. No two snow events are identical, and the resulting snow loads on nearby buildings from one snow event may be different. One foot of snow on the ground does not necessarily equal 1 foot of snow on .
Model of pressure washer, Serial number of pressure washer. Discuss the issue. Customer service will advise which authorised service agent to take the pressure washer to provided the issue is a warranty one. Take pressure washer to authorised service agent for repair. What is not covered. Commercial use of pressure washer.
the pressure washer. Contact a Authorized Service Center. Using the pressure washer in this condition may damage the device and / or cause personal injuries Disconnect the power cable when not using the pressure washer and before removing the high-pressure hose. When the pressure washer
Lock Washer and Washer Sheet Metal Screw and Washer Rear Bracket Rear Bracket Mounting Stud M6-1.0 Nut and Washer NOTE: Press tape should cover all metal portions of the #10 fitting. M8-1.25 x 15mm Bolt, Lock Washer, Washer & Nut M8-1.25 x 15mm Bolt, Lock Washer, Washer & Nut M8-
Hard Washer 56 296418W 16 . Hard Washer 57 296420W 16 . Hard Washer 58 296422W 22 . Hard Washer 59 296428W 4 . Hard Washer 60 296430W 8 . Hard Washer 61 302400W 5 . . PRESSURE CHECK TRANS 4TH CLUTCH PRESSURE CHECK TRANS LUBE PRESSURE TRANS FWD CLUTCH PRESSUR
pressure washer helpline at 1-800-270-1408. PREPARING PRESSURE WASHER FOR USE If you haveany problems with the assemblyof your pressure washer or if parts are missingor damaged,call the pressure washer helpline at 1-800-270-1408. 4. Secure handleto pressure washer usingfour provided flangenuts. 5. Slowly tip
FrostGuard is designed to remove melt water, not accumulated snow. FrostGuard heating cable will not keep snow or ice from falling off the roof. Snow fences or snow guards should be used to eliminate snow movement. For the names of manufacturers of snow guards or snow fences, contact Pentair Thermal Building Solutions at (800) 545-6258.
