INTERFACE STANDARD ENVIRONMENTAL CONDITIONS
UNCLASSIFIEDNOT MEASUREMENTSENSITIVEATPD-240421 OCTOBER 2011INTERFACE STANDARDENVIRONMENTAL CONDITIONS FOR THE HEAVYBRIGADE COMBAT TEAM TRACKED VEHICLESYSTEMSUNCLASSIFIED: Distribution Statement A. Approved for public release.
UNCLASSIFEDATPD-2404FOREWORD1. This standard is approved for use by the U.S. Army Tank Automotive Research,Development and Engineering Center (TARDEC), Research, Development and EngineeringCommand (RDECOM), Department of the Army, and is available for use by all Departments andAgencies of the Department of Defense.2. Comments, suggestions, or questions on this document should be addressed to U.S. ArmyTank-automotive and Armaments Command, ATTN: RDTA-EN/STND/TRANS, MS# 268,6501 E. 11 Mile Road, Warren, MI 48397-5000 or emailed toDAMI STANDARDIZATION@conus.army.mil. Since contact information can change, youmay want to verify the currency of this address information using the ASSIST Online database athttp://assist.daps.dla.mil.iiUNCLASSIFIED
UNCLASSIFEDATPD-24041SCOPE . 1Scope. . 1Application. . 12APPLICABLE DOCUMENTS . 12.1General. . 12.2Government documents. . 12.2.1Specifications, standards and handbooks. . 12.2.2Other Government documents, drawings, and publications. . 22.3Non-Government publications. . 32.4Order of precedence. . 33DEFINITIONS . 33.1Environmental test. . 33.2Induced environment. . 33.3In-service use. . 33.4Life cycle profile. . 33.5Material. . 43.6Materiel. . 43.7Mission profile. . 43.8Operational check. . 43.9Operational worthiness. . 43.10 Platform. . 43.11 Platform environment. . 43.12 Relative humidity. . 43.13 Subsystem. . 43.14 System. . 53.15 Temperature shock. . 53.16 Test item. . 53.17 Test procedure. . 54GENERAL REQUIREMENTS . 54.1General. . 55DETAILED REQUIREMENTS . 65.1Natural environment. . 65.1.1High temperature. . 65.1.1.1 Storage and transportation. . 65.1.1.2 Operational. 65.1.2Low temperature. . 65.1.2.1 Storage and transportation. . 65.1.2.2 Operational. 75.1.3Humidity. . 75.1.3.1 System. . 75.1.3.2 Subsystem storage and transportation. . 75.1.3.3 Subsystem operational. . 75.1.4Salt fog. 75.1.5Fungus. . 85.1.6Sand. . 85.1.6.1 Blowing sand external. 85.1.6.2 Blowing sand internal. . 85.1.7Dust. 81.11.2iiiUNCLASSIFIED
UNCLASSIFEDATPD-24045.1.7.1 Blowing dust external. . 85.1.7.2 Blowing dust internal. . 85.1.8Altitude. . 95.1.8.1 Operating. 95.1.8.2 Non-operating. . 95.1.9Solar radiation. 95.1.10 Icing freezing rain. . 95.1.11 Rain. 95.1.12 Snow. . 95.1.13 Wind. . 95.2Induced environment. . 105.2.1Vibration. . 105.2.2High Temperature. . 155.2.2.1 Storage and Transportation. . 155.2.2.2 Operational. 165.2.3Low temperature. . 165.2.3.1 Storage and transportation. . 165.2.3.2 Operational internal. . 165.2.3.3 Operational external. . 175.2.4Temperature shock. . 175.2.5Shock. . 175.2.5.1 Basic shock. . 175.2.5.2 Functional shock. . 175.2.5.3 Gunfire shock. . 185.2.5.4 Ballistic shock. . 185.2.5.5 High intensity shock. . 185.2.5.6 Transport shock. . 195.2.5.7 Handling shock. . 195.2.5.8 Bench handling. . 195.2.6Leakage (immersion). .
MIL-PRF-46170 - Hydraulic Fluid, Rust Inhibited, Fire Resistant, Synthetic Hydrocarbon Base, NATO Code No. H-544 MIL-DTL-83133 - Turbine Fuel, Aviation, Kerosene Type, JP-8 (NATO F 34), NATO F-35, and JP-8 100 (NATO F-37) DEPARTMENT OF DEFENSE STANDARDS MIL-STD-810 - Department of Defense Test Method Standard
According to IEC 61400- 1 and 61400-3 the site specific conditions can be broken down into wind conditions, other environmental conditions, soil conditions, ocean/lake conditions and electrical conditions. All of these site conditions other than site specific wind conditions and related documents are out of scope for this standard.
21 TDR cable test interface (Optional) 22 SDI input (BNC interface) ( Optional) 23 RS485 Interface: RS485communication for the PTZ 24 HDMI IN 25 Video signal output（BNC interface）/ cable tracer interface 26 CVBS IN/AHD /TVI/CVI Coaxial interface /（BNC interface）(AHD /TVI/CVI) 27 Optical power meter interface (Optional)
Contents iv Cisco IOS XR Command Modes Reference HSRP Interface Configuration Mode CMR-6 Interface Address Family Configuration Mode CMR-7 Interface Configuration Mode CMR-7 Interface Configuration Mode (Protocol Areas) CMR-8 Interface IGMP Configuration Mode CMR-8 Interface Management Configuration Mode CMR-8 Interface Mulitcasting Mode CMR-9 Interface PIM Configuration Mode CMR-9
T A B L E O F C O N T E N T S Description Page No. Criterion 1: Program Mission, Objectives and Outcomes Standard 1.1.1 Standard 1.1.2 (a&b) Standard 1.1.3 Standard 1.1.4 Standard 1.2 Standard 1.3 Standard 1.4 Criterion 2: Curriculum Design and Organization Standard 2.1 Standard 2.2 Standard 2.3 Standard 2.4 Standard 2.5 Standard 2.6
Paper Tray (250 sheets) Standard Standard Standard Manual Feeder Slot (1 sheet) Standard Standard Standard Output Tray (120 sheets) Standard Standard Standard AirPrint Standard Standard Not Applicable Google Cloud Print Standard Standard Not Applicable Network Printing S
WebSphere MQ Programming, P39-1365 9 Chapter: 1. Overview Section: Using an Interface layout as a template for your Interface Using an Interface layout as a template for your Interface The Interface layouts that (along with the generalized Interface program) make up WebSphere MQ Programming are templates for your Interfaces. To use an Interface
Dec 01, 2018 · standard terms & conditions of sale . terms & conditions of sale. buyer’s offer resulting from sensata technologies inc., quotation is expressly conditioned upon buyer’ s assent to sensata’ s standard terms and conditions of sale printed below. all orders will be subject to these standard terms and conditions of sale.
This thesis focuses on the camera serial interface test environment development and signal integrity verification. The used standard is the MIPI D-PHY CSI-2 (Mobile In-dustry Processor Interface D-Physical Layer Camera Serial Interface 2), which is a commonly used camera serial interface standard in mobile devices.
