Simultaneous Dual-Band Wireless-N Router
USER GUIDESimultaneous Dual-BandWireless-N RouterModel:WRT400N
About This GuideAbout This GuideIcon DescriptionsWhile reading through the User Guide you may seevarious icons that call attention to specific items. Below isa description of these icons:NOTE: This check mark indicates that there isa note of interest and is something that youshould pay special attention to while using theproduct.WARNING: This exclamation point indicatesthat there is a caution or warning and it issomething that could damage your property orproduct.WEB: This globe icon indicates a noteworthywebsite address or e-mail address.Online ResourcesWebsite addresses in this document are listed withouthttp:// in front of the address because most current webbrowsers do not require it. If you use an older web browser,you may have to add http:// in front of the web ys www.linksys.com/glossaryNetwork Securitywww.linksys.com/securityCopyright and TrademarksLinksys, Cisco, and the Cisco Logo areregistered trademarks or trademarks ofCisco Systems, Inc. and/or its affiliatesin the U.S. and certain other countries.Copyright 2009 Cisco Systems, Inc. Allrights reserved. Other brands and productnames are trademarks or registeredtrademarks of their respective holders.Simultaneous Dual-Band Wireless-N Routeri
Table of ContentsChapter 1: Product Overview1Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Chapter 2: Wireless Security Checklist3General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Chapter 3: Advanced Configuration4Setup Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Setup MAC Address Clone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Setup Advanced Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Wireless Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Wireless Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Wireless Wireless MAC Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Wireless Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Security Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Security VPN Passthrough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Access Restrictions Internet Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Applications and Gaming Port Range Forwarding . . . . . . . . . . . . . . . . . . . . . . . 18Applications & Gaming Port Triggering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Applications and Gaming DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Applications and Gaming QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Administration Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Administration Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Administration Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Administration Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Administration Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Status Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Status Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Status Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Appendix A: Troubleshooting26Appendix B: Specifications27Appendix C: Warranty Information28Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Exclusions and Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Obtaining Warranty Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Simultaneous Dual-Band Wireless-N Routerii
Table of ContentsAppendix D: Regulatory Information30FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30FCC Radiation Exposure Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Restrictions in the 5 GHz Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Avis d’Industrie Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Restrictions dans la bande 5 GHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Wireless Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Avis de non-responsabilité concernant les appareils sans fil . . . . . . . . . . . . . . . . . . 31User Information for Consumer Products Covered by EU Directive 2002/96/EC on WasteElectric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Appendix E: Software End User License Agreement36Cisco Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Software Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Simultaneous Dual-Band Wireless-N Routeriii
Product OverviewChapter 1Chapter 1:Product OverviewThank you for choosing the Linksys by Cisco SimultaneousDual-Band Wireless-N Router. The Router lets you accessthe Internet via a wireless connection or through one ofits four switched ports. You can also use the Router toshare resources, such as computers.For more wireless bandwidth, the Router can create twosimultaneous yet separate Wireless-N networks, oneusing the 5 GHz band and one using the 2.4 GHz band.For example, use the Wireless-N 2.4 GHz network tosurf, e-mail, and print while keeping the less crowded,Wireless-N 5 GHz network free for time‑sensitive trafficlike music, gaming, and high‑definition video. For moreinformation, refer to Simultaneous Networks, page 10.Front Panel1, 2, 3, 4 (Blue) These numbered LEDs,corresponding with the numbered ports on theRouter’s back panel, serve two purposes. If theLED is continuously lit, the Router is successfullyconnected to a device through that port. Aflashing LED indicates network activity overthat port.Wi-Fi Protected Setup Button If you haveclient devices, such as wireless adapters, thatsupport Wi-Fi Protected Setup, then you canuse Wi-Fi Protected Setup to automaticallyconfigure wireless security for your wirelessnetwork(s).To use Wi-Fi Protected Setup, run the LinksysEasy Link Advisor (LELA) , or refer toWi-FiProtected Setup, page 11.Wi-Fi Protected Setup (WPS) LED (Blue/Amber) The LED flashes blue for twominutes during the WPS process and lightsup blue when the WPS process is successful.The LED lights up amber if there is an errorduring the Wi‑Fi Protected Setup process. Makesure the client device supports Wi‑Fi ProtectedSetup. Wait until the LED is off, and then try again.The LED flashes when a Wi‑Fi Protected Setupsession is active. The Router supports onesession at a time. Wait until the LED is solidly lit,or off before starting the next Wi-Fi ProtectedSetup session.Wireless (Blue) The Wireless LED lights upwhen the wireless feature is enabled. If the LEDis flashing, the Router is actively sending orreceiving data over the network.Internet (Blue) The Internet LED lights upwhen there is a connection made through theInternet port. A flashing LED indicates networkactivity over the Internet port. The LED lights upGreen when it is connected to 10/100 port andBlue when it is connected to a gigabit port.Power (Blue) The Power LED lights up and willstay on while the Router is powered on. Whenthe Router goes through its self-diagnosticmode during every boot-up, this LED will flash.When the diagnostic is complete, the LED willbe solidly lit.Back PanelInternet The Internet port is where you willconnect your cable or DSL Internet connection.1, 2, 3, 4 These Ethernet ports (1, 2, 3, 4) connectthe Router to PCs on your wired network andother Ethernet network devices.Reset There are two ways to reset the Router’sfactory defaults. Either press and hold the ResetButton for approximately five seconds, or restorethe defaults from Administration FactoryDefaults in the Router’s web-based utility.Power The Power port is where you willconnect the power adapter.Simultaneous Dual-Band Wireless-N Router1
Product OverviewChapter 1Horizontal PlacementFollow these instructions:The Router has four rubber feet on its bottom panel. Placethe Router on a level surface near an electrical outlet.1. Determine where you want to mount the Router. Makesure that the wall you use is smooth, flat, dry, andsturdy. Also make sure the location is within reach ofan electrical outlet.2. Drill two holes into the wall. Make sure the holes are152 mm (6 inches) apart.3. Insert a screw into each hole and leave 3 mm(0.12 inches) of its head exposed.4. Maneuver the Router so the wall-mount slots line upwith the two screws.5. Place the wall-mount slots over the screws and slidethe Router down until the screws fit snugly into thewall-mount slots.Wall-Mounting PlacementThe Router has two wall-mount slots on its bottompanel. The distance between the slots is 152 mm(6 inches).Two screws are needed to mount the Router.4-5 mm1-1.5 mm2.5-3.0 mmSuggested Mounting Hardware††Note: Mounting hardware illustrations are nottrue to scale.NOTE: Linksys is not responsible for damagesincurred by insecure wall-mounting hardware.152 mmPrint this page at 100% size.Cut along the dotted line, and place on the wall to drill precise spacing.Wall-Mounting TemplateSimultaneous Dual-Band Wireless-N Router2
Wireless Security ChecklistChapter 2Chapter 2:Wireless Security ChecklistWireless networks are convenient and easy to install, sohomes with high-speed Internet access are adopting themat a rapid pace. Because wireless networking operates bysending information over radio waves, it can be morevulnerable to intruders than a traditional wired network.Like signals from your cellular or cordless phones, signalsfrom your wireless network can also be intercepted. Sinceyou cannot physically prevent someone from connectingto your wireless network, you need to take some additionalsteps to keep your network secure.1. Change the default wirelessnetwork name or SSIDWireless devices have a default wireless network nameor Service Set Identifier (SSID) set by the factory. Thisis the name of your wireless network, and can be upto 32 characters in length. Linksys wireless productsuse linksys as the default wireless network name. Youshould change the wireless network name to somethingunique to distinguish your wireless network from otherwireless networks that may exist around you, but do notuse personal information (such as your Social Securitynumber) because this information may be available foranyone to see when browsing for wireless networks.2. Change the default passwordFor wireless products such as access points and routers,you will be asked for a password when you want to changetheir settings. These devices have a default password setby the factory. The Linksys default password is admin.Hackers know these defaults and may try to use themto access your wireless device and change your networksettings. To thwart any unauthorized changes, customizethe device’s password so it will be hard to guess.3. Enable MAC address filteringLinksys routers give you the ability to enable Media AccessControl (MAC) address filtering. The MAC address is aunique series of numbers and letters assigned to everynetworking device. With MAC address filtering enabled,wireless network access is provided solely for wirelessdevices with specific MAC addresses. For example, you canspecify the MAC address of each computer in your homeso that only those computers can access your wirelessnetwork.Simultaneous Dual-Band Wireless-N Router4. Enable encryptionEncryption protects data transmitted over a wirelessnetwork. Wi-Fi Protected Access (WPA/WPA2) and WiredEquivalent Privacy (WEP) offer different levels of securityfor wireless communication.A network encrypted with WPA/WPA2 is more securethan a network encrypted with WEP, because WPA/WPA2uses dynamic key encryption. To protect the informationas it passes over the airwaves, you should enable thehighest level of encryption supported by your networkequipment.WEP is an older encryption standard and may be theonly option available on some older devices that do notsupport WPA.General Network Security GuidelinesWireless network security is useless if the underlyingnetwork is not secure. Password protect all computers on the network andindividually password protect sensitive files. Change passwords on a regular basis. Install anti-virus software and personal firewallsoftware. Disable file sharing (peer-to-peer). Some applicationsmay open file sharing without your consent and/orknowledge.Additional Security Tips Keep wireless routers, access points, or gateways awayfrom exterior walls and windows. Turn wireless routers, access points, or gatewaysoff when they are not being used (at night, duringvacations). Use strong passphrases that are at least eight charactersin length. Combine letters and numbers to avoid usingstandard words that can be found in the dictionary.WEB: For more information on wirelesssecurity, visit www.linksys.com/security3
Advanced ConfigurationChapter 3Chapter 3:Advanced ConfigurationSetup Basic SetupThe first screen that appears is the Basic Setup screen. Thisallows you to change the Router’s general settings.After setting up the Router with the Setup Wizard (locatedon the CD-ROM), the Router will be ready for use. If you’dlike to change its advanced settings, use the Router’s webbased utility. This chapter describes each web page of theutility and each page’s key functions. You can access theutility via a web browser on a computer connected to theRouter.The web-based utility has these main tabs: Setup, Wireless,Security, Storage, Access Restrictions, Applications &Gaming, Administration, and Status. Additional tabs willbe available after you click one of the main tabs.NOTE: When you first install the Router, youshould use the Setup Wizard on the SetupCD-ROM. If you want to configure advancedsettings, use this chapter to learn about theweb-based utility.How to Access the Web-Based UtilityTo access the web-based utility, launch the web browser onyour computer, and enter the Router’s default IP address,192.168.1.1 or http://wrt400n.com in the Address field.Then, press Enter.A password request screen will appear. (Non-Windows XPusers will see a similar screen.) Leave the User name fieldblank. The first time you open the web-based utility, usethe default password admin. (You can set a new passwordon the Administration Management screen.) Click OK tocontinue.Setup Basic SetupLanguageLanguage To use a different language, select one fromthe drop-down menu. The language of the web-basedutility will change five seconds after you select anotherlanguage.Click Save Settings to apply your changes, or click CancelChanges to cancel your changes.Internet SetupThe Internet Setup section configures the Router to yourInternet connection. Most of this information can beobtained through your Internet Service Provider (ISP).Internet Connection TypeSelect the type of Internet connection your ISP providesfrom the drop-down menu. The available types are:Password ScreenSimultaneous Dual-Band Wireless-N Router Automatic Configuration - DHCP Static IP PPPoE PPTP L2TP Telstra Cable4
Advanced ConfigurationChapter 3Automatic Configuration - DHCPBy default, the Router’s Internet Connection Type is setto Automatic Configuration - DHCP, which should bekept only if your ISP supports DHCP or you are connectingthrough a dynamic IP address. (This option usually appliesto cable connections.)Internet Connection Type Automatic Configuration - DHCPStatic IPIf you are required to use a permanent IP address toconnect to the Internet, select Static IP.Internet Connection Type Static IPIP Address This is the Router’s IP address, when seen fromthe Internet. Your ISP will provide you with the IP Addressyou need to enter here.Service Name (optional) If provided by your ISP, enterthe Service Name.Connect on Demand: Max Idle Time You can configurethe Router to cut the Internet connection after it has beeninactive for a specified period of time (Max Idle Time). Ifyour Internet connection has been terminated due toinactivity, Connect on Demand enables the Router toautomatically re-establish your connection as soon as youattempt to access the Internet again. To use this option,select Connect on Demand. In the Max Idle Time field,enter the number of minutes you want to have elapsedbefore your Internet connection terminates. The defaultMax Idle Time is 5 minutes.Keep Alive: Redial Period If you select this option,the Router will periodically check your Internetconnection. If you are disconnected, then the Routerwill automatically re-establish your connection. To usethis option, select Keep Alive. In the Redial Period field,you specify how often you want the Router to checkthe Internet connection. The default Redial Period is30 seconds.PPTPPoint-to-Point Tunneling Protocol (PPTP) is a service thatapplies to connections in Europe only.Subnet Mask This is the Router’s Subnet Mask, as seenby users on the Internet (including your ISP). Your ISP willprovide you with the Subnet Mask.Default Gateway Your ISP will provide you with theGateway Address, which is the ISP server’s IP address.DNS Your ISP will provide you with at least one DNS(Domain Name System) Server IP Address.PPPoESome DSL-based ISPs use PPPoE (Point-to-Point Protocolover Ethernet) to establish Internet connections. If you areconnected to the Internet through a DSL line, check withyour ISP to see if they use PPPoE. If they do, you will haveto enable PPPoE.Internet Connection Type PPTPIf your ISP supports DHCP or you are connecting througha dynamic IP address, then select Obtain an IP AddressAutomatically. If you are required to use a permanent IPaddress to connect to the Internet, then select Specify anIP Address. Then configure the following:Internet Connection Type PPPoEUser Name and Password Enter the User Name andPassword provided by your ISP.Simultaneous Dual-Band Wireless-N RouterInternet IP Address This is the Router’s IP address, asseen from the Internet. Your ISP will provide you with theIP Address you need to specify here.Subnet Mask This is the Router’s Subnet Mask, as seenby users on the Internet (including your ISP). Your ISP willprovide you with the Subnet Mask.5
Advanced ConfigurationChapter 3Default Gateway Your ISP will provide you with theGateway Address, which is the ISP server’s IP address.before your Internet connection terminates. The defaultMax Idle Time is 5 minutesDNS Your ISP will provide you with at least one DNS(Domain Name System) Server IP Address.Keep Alive: Redial Period If you select this option,the Router will periodically check your Internetconnection. If you are disconnected, then the Routerwill automatically re-establish your connection. To usethis option, select Keep Alive. In the Redial Period field,you specify how often you want the Router to checkthe Internet connection. The default Redial Period is30 seconds.Server IP Address Your ISP will provide you with theServer IP Address.User Name and Password Enter the User Name andPassword provided by your ISP.Connect on Demand: Max Idle Time You can configurethe Router to cut the Internet connection after it has beeninactive for a specified period of time (Max Idle Time). Ifyour Internet connection has been terminated due toinactivity, Connect on Demand enables the Router toautomatically re-establish your connection as soon as youattempt to access the Internet again. To use this option,select Connect on Demand. In the Max Idle Time field,enter the number of minutes you want to have elapsedbefore your Internet connection terminates. The defaultMax Idle Time is 5 minutes.Keep Alive: Redial Period If you select this option, theRouter will periodically check your Internet connection. Ifyou are disconnected, then the Router will automaticallyre-establish your connection. To use this option, select KeepAlive. In the Redial Period field, specify how often you wantthe Router to check the Internet connection. The defaultvalue is 30 seconds.L2TPL2TP is a service that applies to connections in Israel only.Telstra CableTelstra Cable is a service that applies to connections inAustralia only.Internet Connection Type Telstra CableServer IP Address This is the IP address of the TelstraCable. Your ISP will provide you with the IP Address youneed to specify here.User Name and Password Enter the User Name andPassword provided by your ISP.Optional SettingsSome of these settings may be required by your ISP. Verifywith your ISP before making any changes.Optional SettingsInternet Connection Type L2TPServer IP Address This is the IP address of the L2TPServer. Your ISP will provide you with the IP Address youneed to specify here.User Name and Password Enter the User Name andPassword provided by your ISP.Connect on Demand: Max Idle Time You can configurethe Router to cut the Internet connection after it has beeninactive for a specified period of time (Max Idle Time). Ifyour Internet connection has been terminated due toinactivity, Connect on Demand enables the Router toautomatically re-establish your connection as soon as youattempt to access the Internet again. To use this option,select Connect on Demand. In the Max Idle Time field,enter the number of minutes you want to have elapsedHost Name/Domain Name These fields allow you tosupply a host and domain name for the Router. Some ISPs,usually cable ISPs, require these names as identification.You may have to check with your ISP to see if yourbroadband Internet service has been configured with ahost and domain name. In most cases, leaving these fieldsblank will work.MTU MTU is the Maximum Transmission Unit. It specifiesthe largest packet size permitted for Internet transmission.Select Manual if you want to manually enter the largestpacket size that is transmitted. To have the Router selectthe best MTU for your Internet connection, keep thedefault setting, Auto.Size When Manual is selected in the MTU field, this optionis enabled. Leave this value in the 1200 to 1500 range. Thedefault size depends on the Internet Connection Type: Simultaneous Dual-Band Wireless-N RouterDHCP, Static IP, or Telstra: 15006
Advanced ConfigurationChapter 3 PPPoE: 1492 PPTP or L2TP: 1460Network SetupThe Network Setup section changes the settings on thenetwork connected to the Router’s Ethernet ports. WirelessSetup is performed through the Wireless tab.Router AddressThis presents both the Router’s IP Address, Subnet Mask,and URL Address as seen by your network. The defaultRouter IP address is 192.168.1.1, and the default URLaddress is http://wrt400n.com.Client Lease Time The Client Lease Time is the amountof time a network user will be allowed connection to theRouter with their current dynamic IP address. Enter theamount of time, in minutes, that the user will be “leased”this dynamic IP address. After the time is up, the user willbe automatically assigned a new dynamic IP address. Thedefault is 0 minutes, which means one day.Static DNS (1-3) The Domain Name System (DNS) is howthe Internet translates domain or website names intoInternet addresses or URLs. Your ISP will provide you with atleast one DNS Server IP Address. If you wish to use another,enter that IP Address in one of these fields. You can enter upto three DNS Server IP Addresses here. The Router will usethese for quicker access to functioning DNS servers.WINS The Windows Internet Naming Service (WINS)manages each computer’s interaction with the Internet. Ifyou use a WINS server, enter that server’s IP Address here.Otherwise, leave this blank.Router IP AddressNetwork Address Server Settings (DHCP)DHCP Reservation Click DHCP Reservation if you wantto assign a fixed local IP address to a MAC address.The settings allow you to configure the Router’s DynamicHost Configuration Protocol (DHCP) server function. TheRouter can be used as a DHCP server for your network. ADHCP server automatically assigns an IP address to eachcomputer on your network. If you choose to enable theRouter’s DHCP server option, make sure there is no otherDHCP server on your network.Network Address Server Settings (DHCP)DHCP Server DHCP is enabled by factory default. If youalready have a DHCP server on your network, or you don’twant a DHCP server, then select Disabled (no other DHCPfeatures will be available).Starting IP Address Enter a value for the DHCP serverto start with when issuing IP addresses. Because theRouter’s default IP address is 192.168.1.1, the StartingIP Address must be 192.168.1.2 or greater, but smallerthan 192.168.1.253. The default Starting IP Address is192.168.1.100.Maximum Number of DHCP Users Enter the maximumnumber of computers that you want the DHCP server toassign IP addresses to. This number cannot be greaterthan 253. The default is 50.Simultaneous Dual-Band Wireless-N RouterDHCP ReservationYou will see a list of DHCP clients with the followinginformation: Client Name, Interface, IP Address, and MACAddress. Click the Select checkbox to reserve a client’s IPaddress. Then click Add Clients.If you want to manually assign an IP address, enter theclient’s name in the Enter Client Name field. Enter the IPaddress you want it to have in the Assign IP Address field.Make sure the IP address is between the starting DHCPserver’s IP address and maximum number of DHCP usersrange. Enter its MAC Address in the To This MAC Addressfield. Click Add.A list of DHCP clients and their fixed local IP addresses willbe displayed at the bottom of the screen. If you want toremove a client from this list, click Remove.7
Advanced ConfigurationChapter 3When you finish your changes, click Save Settings tosave your changes. Click Cancel Changes to cancel yourchanges. To view the most up-to-date information, clickRefresh. To exit this screen, click Close.Time SettingSelect the time zone in which your network functionsfrom this drop-down menu. (You can even automaticallyadjust for daylight saving time.)Time SettingClick Save Settings to apply your changes, or click CancelChanges to cancel your changes.Setup DDNSThe Router offers a Dynamic Domain Name System (DDNS)feature. DDNS lets you assign a fixed host and domainname to a dynamic Internet IP address. It is useful whenyou are hosting your own website, FTP server, or otherserver behind the Router.Before you can use this feature, you need to signup for DDNS service with a DDNS service provider,www.dyndns.org or www.TZO.com. If you do not want touse this feature, keep the default setting, Disabled.DDNSUser Name Enter the User Name for your DDNS account.Password Enter the Password for your DDNS account.Host Name The is the DDNS URL assigned by the DDNSservice.System Select the DynDNS service you use: Dynamic,Static, or Custom. The default selection is Dynamic.Mail Exchange (Optional) Enter the address of your mailexchange server, so e-mails t
Chapter 2 Wireless Security Checklist Simultaneous Dual-Band Wireless-N Router 3 Chapter 2: Wireless Security Checklist Wireless networks are convenient and easy to install, so homes with high-speed Internet access are adopting them at a rapid pace. Because wireless networking operates by sending information over radio waves, it can be more
TRENDnet’s AC1750 Dual Band Wireless Router, model TEW-812DRU, produces the ultimate wireless experience with gigabit wireless speeds. Manage two wireless networks—the 1300 Mbps Wireless AC band for the fastest wireless available and the 450 Mbps Wireless N ba
Cope & Stick - 500 Series Veneer Doors Miter Frame - 500 Series. Style Band 1 Band 2 Band 3 Band 4 Band 5 101 Glass 10 12 13 16 18 Material Band 1 Band 2 Band 3 Band 4 Band 5 102/104 Glass 12 14 15 18 20 Paint X Notes - PRICES ARE PER SQ/FT Maple Paint X Minimum Dimensions - Doors 7"W x 7"H Natural Soft Maple X
Affairs Group 75: Records of the Osage Agency - Annuity Payment Rolls, 1880-1907 (Roll 1 of 21) Osage Annuity Payment Roll: 1 st and 2nd Quarters of 1880 o Big Chief Band o Joe's Band o Big Hill Band o White Hair Band o Tall Chief Band o Black Dog Band o Saucy Chief Band o Beaver Band o Strike Axe Band o No-Pa-Walla Band
FOSCAM VD1 4MP Dual Band Wi-Fi Video Doorbell User Guide March 16, 2022March 18, 2022 Leave a comment on FOSCAM VD1 4MP Dual Band Wi-Fi Video Doorbell User Guide Home » FOSCAM » FOSCAM VD1 4MP Dual Band Wi-Fi Video Doorbell User Guide Contents hide 1 FOSCAM VD1 4MP Dual Band Wi-Fi Video Doorbell 2 What's in the Box 3 Physical Description
Wireless AC3200 Tri Band Gigabit Cloud Router Wireless AC3150 Ultra-WiFi Gigabit Cloud Router Wireless AC1900 Gigabit Cloud Router Wireless AC1750 Gigabit Cloud Router Wireless AC1750 High-Power Gigabit Router Wireless AC1200 Gigabit Cloud Router Wireless Technology Tri Band Wireless AC (5300
CEFR level: IELTS band: C1 IELTS band: 8 IELTS band: 7.5 IELTS band: 7 B2 IELTS band: 6.5 IELTS band: 6 IELTS band: 5.5 IELTS : 4.5 IELTS band: 4 IELTS band: 5 978-X-XXX-XXXXX-X Author Title C M Cullen, French and Jakeman Y K Pantoene XXX STUDENT'S BOOK with DVD-ROM WITH ANSWERS B1-C1 The
WIKUS BAND SAW BLADES Bimetal band saw blades Diamond coated band saw blades Carbide band saw blades Carbon steel band saw blades Sales units: coils in fixed lengths and manufacturing coils up to 120 m, depending on the band width, welded-to-length band saw blades Band widths: 4 to 125 mm Constant tooth pitches: 0,75 to 18 teeth per inch (tpi)
Stage: Final Source of intervention: Domestic Type of measure: Secondary legislation Contact for enquiries: BEISContractsForDifference@beis.gov.uk Summary: Intervention and Options RPC Opinion: Not Applicable Cost of Preferred (or more likely) Option Total Net Present Social Value: 0-240m Business Net Present Value: N/A Net cost to business per year: N/A Business Impact Target Status Non .
