MCI PEDAL STEEL Users Manual - Steel Guitar
MCI PEDAL STEELUsers ManualREAD THIS WHEN ALL ELSE FAILS!
MCI Pedal Steel Guitar
Page 1MCI PEDAL STEEL MANUAL1.0. SET-UP1.1.Open the case. Remove the legs from the inside of the case.Do not remove the guitar.1.2.Screw front legs (marked with an "F") in the front leg sockets.1.3.Attach the pedal bar to the front legs (Figure 1-1).1.4.Connect the pedal rods to the pedals in order.(1is the rod closest to the keyhead end of the guitar, up to 8,the rod closest to the bridge end of the guitar).1.5.Attach the back legs.1.7.Take the guitar out of the case and set it upright.1.8.Plug your cable in to the 1/4" phone jack (beneath the guitar on the bridge end).NOTE:When you want to disassemble your guitar, set it back into the case first, then take it apartexactly the reverse way that you put it together.1.9.Table 1-1 shows the proper pitches at which to tune the strings on both the E9 and tringPitch1G or D2E3C4A5G6E7C8A9F10C
Page 2
Page 3TABLE 1-1b: PITCH VALUES2.0. ADJUSTMENTS2.1. Pedal and Knee-Lever Action 2.1.1.Pedal actionAdjust the screw in the pedal stop bar (below each pedal pull bar) for theamount of pedal travel you desire. A long travel distance makes the actionsofter and takes more time to change the pitch. The shorter the traveldistance, the harder the action is and the less time it takes to change thepitch. Make small adjustments. See Figure 2-1.
Page 42.1.2.Knee-lever actionAdjust the screw in each knee-lever stop for the amount of lever travelyou desire. Make small adjustments.2.2Raise and Lower Pull Rods2.2.1.Adjusting rod travel1. Loosen the tuning nut with the tuning wrench enough for the rod to slipoff the pull bar (figure 2-2a).
Page 52.Place the hook of the pull rod into another slot in the pull bar (figure 2-2b). Thefurther the rod is from the cross bar, the greater the pitch change.3.Tighten the tuning nut until you get the pitch change you need.2.2.2.Repositioning pull rodsNOTE:The MCI pedal steel guitar comes from the factory set to the standard 8-4 format(figure 2-3). See figure 2-4 for the lever raise (LR) and lever lower (LL) positions.
Page 6
Page 7
Page 8
Page 9
Page 10IMPORTANT: Start with the longest rods first, then go to the next longest, and so on until you reachthe shortest rods.1. Remove the tuning nut with the tuning wrench.2. Slide the pull rod off the pull bar.3. Loosen the screw on the pull bar. Slide the pull bar to the desired position.Tighten the screw.4. Insert the straight end of the pull rod into the first open "raise" or "lower" holeclosest to the spring. The group of the three holes closest to the spring is for"lower" rods; the other group of three is for "raise" rods.5. Place the hook end of the pull rod into the desired slot on the pull bar. The furthestslot away from the crossrod will cause the greatest change in pitch.6. Screw the tuning nut onto the straight end of the pull rod.Tighten the tuning nut until you reach the pitch change you want.3.0GENERAL INFORMATION3.1. Neck Selector SwitchThere are two pushbutton selector switches between the necks. The right-hand switch selects theneck: the "up" position "turns on" the E9 (or upper) neck. The "down" position selects the C6 (orlower) neck. The lefthand switch, when in the "down" position, "turns on" both necks at the sametime.3.2. Changing Strings3.2.1. Replacing a string1. Place the ball end of the string between the "fingers" in the tailpiece.
Page 11
MCI PEDAL STEEL Users Manual READ THIS WHEN ALL ELSE FAILS! MCI Pedal Steel Guitar. Page 1 E9 C6 String Pitch String Pitch 1 F# 1 G or D 2D# 2 E 3G# 3 C 4E 4A 5B 5G 6G# 6 E 7F# 7 C 8E 8A 9D 9F 10 B 10 C MCI PEDAL STEEL MANUAL 1.0. SET-UP 1.1. Op
MCI 10 - 0.3 0.47K0.2 - 1.48C - 0.29D0.7 MCI 1 10 - 2.23C0.3 TMI Tokyo Maintenance MCI 2 0.7 10 - 0.54D MCI 1 MCI if cracking is the major factor MCI 2 MCI if rutting is the major factor Index K surface roughness index, cm C cracked area percentage TMI C D D rut depth, cm South Korea (Suh et al., 2017)
MCI Coin is the basic currency system for ecosystem participation among viewers, fans, advertiser, and creators on the platform. 10 support of creators, using MCI coins in voicing opinions offered with advertising and branded content at a lower cost Rewarded with MCI coins as much as the amount of support to the Future creator's revenue
Inching pedal, function check 413 Service Information 2014/12/22 Profile: GRD, G976 [GB] Inching pedal, function check Op nbr413-019 1.After repair work has been completed in any inching pedal related system, an inching pedal functioncheck
Effect Pedal Kits: Rangemaster Treble Booster . The Dallas Rangemaster is the most famous treble booster effect pedal, and it was the first pedal of its kind. This effect pedal was . frequencies in the typical dark British amp sounds, now the Rangemaster Treble Booster is really useful to
Please take the time to read this manual to get the most out of your pedal. The more you familiarize yourself with the features of this pedal, the more you will enjoy its benefits and maximize its potential. OVERVIEW: Koko Boost is a unique boost pedal that incorporates both a clean transparent boost and a selectable midrange boost.
Oct 14, 2010 · Tc‐99m compared to I‐131 Tc‐99m patient’s could be given as much as 760 mCi and be released. 30 mCi of Tc‐99m imparts a very modest dose to the most exposed person. On the other hand, 30 mCi of I‐131 is close to the 500 m
ESP Medical Director, ESP Director, MCI Manager, Quality Management/Risk Management Director, Clinical Supervisors, Triage Clinicians, Master’s-Level Clinicians, Psychiatry, . 10 Mobile Crisis Intervention (MCI) MCI prov
Sector shutdowns during the coronavirus crisis: which workers are most exposed? Authors: Robert Joyce (IFS) and Xiaowei Xu (IFS) Summary The lockdown in response to the Covid-19 pandemic has effectively shut down a number of sectors. Restaurants, shops and leisure facilities have been ordered to close, air travel has halted, and public transport has been greatly reduced. Our analysis shows .
