GY PC125 CRIMP SPECIFICATIONS - Pulsar Hydraulics
GY PC125 CRIMP SPECIFICATIONSPrinted: Dec 13 2021
CRIMP erruleCrimp InstructionsOne-pieceCHART NUMBER83REV 00Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or engthmmCrimp DiametermmDial SettingApprox. Actualin111 -04 42002316Full16.7 0.6570.7111 -06 42002519Full20.9 0.8231.9111 -08 42002723Full24.2 0.9531.2111 -12 42003431Full31.8 1.2520.8111 -16 42004434Full40.6 1.5986.6IT01Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCrimp InstructionsOne-pieceCHART NUMBER183REV 00Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or engthmmCrimp DiametermmDial SettingApprox. Actualin110 -04 42002314Full15.7 0.6181.7110 -06 42002519Full19.8 0.7800.8110 -08 42002723Full23.3 0.9170.3IT69Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCrimp InstructionsOne-pieceCHART NUMBER86REV 00Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or engthmmCrimp DiametermmDial SettingApprox. Actualin112 -04 42002316Full16.8 0.6610.8112 -06 42002519Full21.0 0.8272.0112 -08 42002723Full25.0 0.9842.0112 -12 42003431Full31.8 1.2520.8112 -16 42004434Full40.6 1.5986.6IT04Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCrimp InstructionsOne-pieceCHART NUMBER84REV 01Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or engthmmCrimp DiametermmDial SettingApprox. Actualin122 -04 42002316Full17.8 0.7011.8122 -06 42002519Full22.0 0.8663.0122 -08 42002723Full25.5 1.0042.5122 -10 42003027Full28.8 1.1341.8122 -12 42003431Full32.1 1.2641.1122 -16 42004441Full41.6 1.6380.6IT02Printed:0113-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCrimp InstructionsOne-pieceCHART NUMBER124REV 00Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or engthmmCrimp DiametermmDial SettingApprox. Actualin114 -04 42002316Full17.2 0.6771.2114 -06 42002519Full20.8 0.8191.8114 -08 42002723Full24.2 0.9531.2114 -10 42003027Full28.5 1.1221.5114 -12 42003431Full31.8 1.2520.8114 -16 42004434Full40.6 1.5986.6IT34Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP oseFerruleCrimp InstructionsOne-pieceCHART NUMBER151REV 02Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or engthmmCrimp DiametermmDial SettingApprox. Actualin124 -06PLUS44002523Full24.0 0.9451.0124 -08PLUS44003123Full26.4 1.0393.4124 -10PLUS44003131Full32.6 1.2831.6124 -12PLUS44003431Full34.3 1.3503.3124 -16PLUS44004741Full42.7 1.6811.7IT53Printed:0213-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCrimp InstructionsOne-pieceCHART NUMBER91REV 01Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or engthmmCrimp DiametermmDial SettingApprox. Actualin124 -06 44002519Full23.1 0.9093.11124 -08 44003123Full25.4 1.0002.4124 -10 44003131Full32.6 1.2831.6124 -12 44003431Full33.9 1.3352.9124 -16 44004741Full41.4 1.6300.4IT09Printed:0113-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCrimp InstructionsOne-pieceCHART NUMBER92REV 03Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or engthmmCrimp DiametermmDial SettingApprox. Actualin136 -12 44003434Full35.3 1.3901.3136 -16 44004741Full42.0 1.6541.0IT10Printed:0313-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP SPECIFICATIONSCrimperHoseCouplingPC1251364600Crimp InstructionsOne-pieceFerruleDieCrimpLengthCrimp DiametermmIT58Printed:0013-Dec-21159REV 00Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or 0.004/-0.008inches.FittingInsertionHoseCHART NUMBERDial SettingApprox. ActualinNOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP 00Crimp InstructionsOne-pieceDieFerrule160REV 00Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or 0.004/-0.008inches.FittingInsertionHoseCHART NUMBERCrimpLengthCrimp DiametermmDial SettingApprox. Actualin156 -12PLUS44003434Full35.1 1.3821.1156 -16PLUS44004741Full42.0 1.6541.0IT59Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP rimp InstructionsOne-pieceFerruleDieCrimpLengthCrimp DiametermmIT71Printed:0013-Dec-21185REV 00Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or 0.004/-0.008inches.FittingInsertionHoseCHART NUMBERDial SettingApprox. ActualinNOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCrimp InstructionsOne-pieceCHART NUMBER186REV 00Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or engthmmCrimp DiametermmDial SettingApprox. Actualin124 -12 42003431Full33.1 1.3032.1124 -16 42004434Full40.4 1.5916.4IT72Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCrimp InstructionsOne-pieceCHART NUMBER95REV 02Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or 0.004/-0.008inches.DieCrimpLengthCrimp DiametermmDial SettingApprox. Actualin151 -044500-0414Knurl16.1 0.6342.1151 -054500-0516Full18.3 0.7202.3151 -064500-0619Full20.0 0.7871.0151 -084500-0819Full22.9 0.9023.9151 -104500-1023Full26.7 1.0513.7151 -124500-1227Full30.8 1.2133.8151 -164500-1634Full35.5 1.3981.5151 -204500-2041Full43.5 1.7132.5151 -244500-2441Knurl46.8 1.8435.8IT12Printed:0213-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP imp InstructionsOne-pieceDieFerrule176REV 00Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or 0.004/-0.008inches.FittingInsertionHoseCHART NUMBERCrimpLengthCrimp DiametermmDial SettingApprox. Actualin151 -054200-042316Full18.1 0.7132.1151 -084200-062519Full22.9 0.9023.9151 -104400-083127Full28.2 1.1101.2151 -124400-103127Full30.8 1.2133.8IT67Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP SPECIFICATIONSCrimperHoseCouplingPC1251515000Crimp InstructionsTwo-pieceCHART NUMBER177REV 00Tolerance 0.1/-0.2mm or 0.004/-0.008 inches .A note on crimping 100R5 hose:SAE 100R5 series hoses were initially designed as a flexible replacement to copper tubing, which is commonly defined by it's outside diameter. The result is that 100R5 hoses have smaller insidediameters than their nominal size (dash size) would indicate. For example, 151-08, nominally 1/2", actually has an I.D. of 13/32", since that is the I.D. of ½" O.D. copper tube. This creates confusionwhen crimping using inserts and ferrules designed for "full dimension hoses", where the nominal size is the inside diameter (ie. -08 hose is ½" I.D.). Be careful to check that selection of the appropriatesized ferrule and insert for the hose you are crimping. Quite often it will be smaller than the dash size of the R5 hose.HoseFerruleDieCrimpLengthCrimp DiametermmDial SettingApprox. Actualin151 -055200-0419Full19.5 0.7680.5151 -085120-0623Full23.6 0.9290.6151 -105120-0827Full28.6 1.1261.6151 -125120-1031Full31.8 1.2520.8IT68Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCrimp InstructionsOne-pieceCHART NUMBER87REV 01Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or engthmmCrimp DiametermmDial SettingApprox. Actualin141 -12 42003431Full33.1 1.3032.1141 -16 42004434Full40.0 1.5756.0IT05Printed:0113-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCoverSkiveLengthCrimp InstructionsSkiveCHART NUMBER122REV 00Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or 0.004/-0.008inches.DieCrimpLengthmmCrimp DiametermmDial SettingApprox. Actualin119 -04 42002116Full16.7 0.6570.7119 -06 42002119Full20.7 0.8151.7IT33Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP FerruleCoverSkiveLengthCrimp InstructionsSkiveCHART NUMBER146REV 01Tolerance 0.1/-0.2mm or 0.004/-0.008 inches .DieCrimpLengthmmCrimp DiametermmDial SettingApprox. Actualin129G -06 42002119Full20.4 0.8031.4129G -06 43002719Full21.4 0.8432.4129G -06 52002519Full20.4 0.8031.4IT49Printed:0113-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP FerruleCrimp InstructionsOne-pieceCHART NUMBER164REV 00Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.1mm/- 0.2mm or engthmmCrimp DiametermmDial SettingApprox. Actualin120J -04 42002316Full16.8 0.6610.8120J -06 42002519Full21.0 0.8272.0IT63Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCrimpInsertSizeCrimp InstructionsOne-pieceCHART NUMBER161REV 01Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.0mm/- 0.2mm or rimp DiametermmDial SettingApprox. Actualin157 -04 4700-032310Knurl11.3 0.4451.3157 -05 4700-042312Knurl12.7 0.5000.7157 -08 4700-062614Knurl16.0 0.6302.0157 -10 4700-082919Knurl20.5 0.8071.5157 -16 4500-164531Knurl32.3 1.2721.3IT60Printed:0113-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP SPECIFICATIONSCrimperHoseCouplingPC1251584700Crimp InstructionsOne-pieceDieFerrule190REV 01Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.0mm/- 0.2mm or 0.004/-0.008inches.FittingInsertionHoseCHART NUMBERCrimpLengthCrimp DiametermmDial SettingApprox. Actualin158 -03 47002310Knurl11.3 0.4451.3158 -04 47002312Knurl12.7 0.5000.7158 -06 47002614Knurl16.0 0.6302.0158 -08 47002919Knurl20.5 0.8071.5158 -10 47003023Knurl25.6 1.0082.6158 -12 47003427Knurl28.1 1.1061.1158 -16 47004534Knurl35.5 1.3981.5IT74Printed:0113-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP SPECIFICATIONSCrimperHoseCouplingPC1251585000Crimp InstructionsOne-pieceDieFerrule191REV 01Tolerance 0.1/-0.2mm or 0.004/-0.008 inches .FittingInsertionHoseCHART NUMBERCrimpLengthCrimp DiametermmDial SettingApprox. Actualin158 -04 55142312Full12.7 0.5000.7158 -05 55142312Full14.4 0.5672.4158 -06 55142614Full16.0 0.6302.0158 -08 55142919Full20.5 0.8071.5158 -10 55143023Full24.8 0.9761.8158 -12 55143423Full27.0 1.0634.0158 -16 55144531Full34.4 1.3543.4IT75Printed:0113-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP SPECIFICATIONSCrimperHoseCouplingPC1251724700Crimp InstructionsNon-SkiveDieFerrule157REV 00Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.0mm/- 0.2mm or 0.004/-0.008inches.FittingInsertionHoseCHART NUMBERCrimpLengthCrimp DiametermmDial SettingApprox. Actualin172 -02 470013.310Full10.6 0.4170.6172 -03 470021.512Full13.1 0.5161.1172 -04 47002314Full15.0 0.5911.0172 -06 47002616Full18.8 0.7402.8172 -08 47002923Full24.1 0.9491.1IT57Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP SPECIFICATIONSCrimperHoseCouplingPC1251824700Crimp InstructionsNon-SkiveDieFerrule175REV 00Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.0mm/- 0.2mm or 0.004/-0.008inches.FittingInsertionHoseCHART NUMBERCrimpLengthCrimp DiametermmDial SettingApprox. Actualin182 -04 47002312Full14.1 0.5552.1182 -06 47002616Full18.4 0.7242.4182 -08 47002923Full23.8 0.9370.8IT66Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP SPECIFICATIONSCrimperHoseCouplingPC1251734700Crimp InstructionsOne-pieceDieFerrule189REV 00Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install thefitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length ofthe ferrule to the Crimp Diameter given in the table. Tolerance 0.0mm/- 0.2mm or 0.004/-0.008inches.FittingInsertionHoseCHART NUMBERCrimpLengthCrimp DiametermmDial SettingApprox. Actualin173 -06 47002619FULL19.4 0.7640.4173 -08 47002923FULL24.8 0.9761.8PUL 173Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCrimp InstructionsTwo-pieceCHART NUMBER96REV 00Tolerance 0.1/-0.2mm or 0.004/-0.008 inches pLengthCrimp DiametermmDial SettingApprox. Actualin109 -04 5000C2014Full15.5 0.6101.5109 -06 5000C2016Full18.7 0.7362.7109 -08 5000C2219Full22.6 0.8903.627Full27.6 1.0870.6109 -10 5000CIT13Printed:0013-Dec-2121NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCrimp InstructionsTwo-pieceCHART NUMBER184REV 00Tolerance 0.1/-0.2mm or 0.004/-0.008 inches .FittingInsertionLengthDieCrimpLengthmmCrimp DiametermmDial SettingApprox. Actualin110 -04 5000C2014Full15.1 0.5941.1110 -06 5000C2016Full18.7 0.7362.7110 -08 5000C2219Full22.5 0.8863.5IT70Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCoverSkiveLengthCrimp InstructionsSkiveCHART NUMBER116REV 00Tolerance 0.1/-0.2mm or 0.004/-0.008 inches .DieCrimpLengthmmCrimp DiametermmDial SettingApprox. Actualin112 -04 5000C1614Full15.9 0.6261.9112 -06 5000C1819Full19.2 0.7560.2112 -08 5000C2023Full23.5 0.9250.5112 -10 5000C2027Full27.6 1.0870.6112 -12 5000C2627Full29.9 1.1772.9112 -16 5000C3534Full38.1 1.5004.1IT30Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCoverSkiveLengthCrimp InstructionsSkiveCHART NUMBER113REV 00Tolerance 0.1/-0.2mm or 0.004/-0.008 inches .DieCrimpLengthmmCrimp DiametermmDial SettingApprox. Actualin111 -04 5000C1614Full15.9 0.6261.9111 -06 5000C1819Full19.3 0.7600.3111 -08 5000C2019Full23.2 0.9133.12111 -12 5000C2627Full29.9 1.1772.9111 -16 5000C3534Full38.1 1.5004.1IT27Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCoverSkiveLengthCrimp InstructionsSkiveCHART NUMBER111REV 00Tolerance 0.1/-0.2mm or 0.004/-0.008 inches .DieCrimpLengthmmCrimp DiametermmDial SettingApprox. Actualin122 -04 5000C1614Full16.4 0.6462.4122 -06 5000C1819Full20.0 0.7871.0122 -08 5000C2023Full23.8 0.9370.8122 -10 5000C2027Full27.9 1.0980.9122 -12 5000C2627Full30.1 1.1853.1122 -16 5000C3534Full38.4 1.5124.4IT26Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP oseFerruleCoverSkiveLengthCrimp InstructionsTwo-pieceCHART NUMBER150REV 01Tolerance 0.1/-0.2mm or 0.004/-0.008 inches .DieCrimpLengthmmCrimp DiametermmDial SettingApprox. Actualin124 -06PLUS54202519Full23.0 0.9063.10124 -08PLUS54202723Full26.2 1.0313.2124 -10PLUS54203027Full29.0 1.1422.0124 -12PLUS54203231Full33.4 1.3152.4124 -16PLUS54204341Full41.7 1.6420.7IT52Printed:0113-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP oseFerruleCrimp InstructionsTwo-pieceCHART NUMBER156REV 00Tolerance 0.1/-0.2mm or 0.004/-0.008 inches .DieCrimpLengthCrimp DiametermmDial SettingApprox. Actualin124 -06PLUS512023Full24.1 0.9491.1124 -08PLUS512027Full27.5 1.0830.5124 -10PLUS512027Full30.0 1.1813.0124 -12PLUS512034Full34.6 1.3620.6124 -16PLUS512041Full42.4 1.6691.4IT56Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP oseFerruleCoverSkiveLengthCrimp InstructionsTwo-pieceCHART NUMBER172REV 00Tolerance 0.1/-0.2mm or 0.004/-0.008 inches .DieCrimpLengthmmCrimp DiametermmDial SettingApprox. Actualin156 -12PLUS54203231Full33.9 1.3352.9156 -16PLUS54204334Full40.8 1.6066.8IT64Printed:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP oseFerruleCrimp InstructionsTwo-pieceCHART NUMBER173REV 01Tolerance 0.1/-0.2mm or 0.004/-0.008 inches .DieCrimpLengthCrimp DiametermmDial SettingApprox. Actualin156 -12PLUS512034Full35.1 1.3821.1156 -16PLUS512041Full42.0 1.6541.0IT65Printed:0113-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP FerruleCrimp InstructionsNon SkiveCHART NUMBER112REV 00Tolerance 0.1/-0.2mm or 0.004/-0.008 inches .FittingInsertionLengthDieCrimpLengthmmCrimp DiametermmDial SettingApprox. Actualin102R -08 5000C2219Full23.0 0.9063.10102R -12 55032827Full31.3 1.2324.3PUL G102RPrinted:0013-Dec-21NOTE: Die and dial settings are approximate recommendations. Ferrules should be crimped withthe largest diameter die set available to make the ridges on the finished crimp as small aspossible. All crimp dimensions must be verified with a calibrated measuring device.
CRIMP erruleCoverSkiveLengthCrimp InstructionsTwo-pieceCHART NUMBER153REV 00Tolerance 0.1/-0.2mm or 0.004/-0.008 inches .DieCrimpLengthmmCrimp DiametermmDial SettingApprox. Actualin114 -04 5000C1614Full15.9 0.6261.9114 -06 5000C1819Full19.1 0.7520.1114 -08 5000C2019Full22.6 0.8903.6114 -10 5000C2023Full26.7 1.0513.7114 -12 5000C2627Full29.8 1.1732.8114 -16 5000C3534Full37.7 1.4843.7IT55Printed:0013-Dec-21NOTE: D
One-piece Fitting Insertion Length Approx. Actual Dial Setting Die PC125 112 Full-04 16.8 0.6614200 23 0.816 112 Full-06 21.0 0.8274200 25 2.019 112 Full-08 25.0 0.9844200 27 2.023 112 Full-12 31.8 1.2524200 34 0.831 112 Full-16 40.6 1.5984200 44 6.634 IT04 00 NOTE: Die and dial settings are approximate recommendations. Ferrules should be .
Crimper Hose Crimp InstructionsCoupling CHART NUMBER REV83 00 mm in Hose Crimp Diameter 111 Mark the hose at a distance from the end of the hose equal to the "Insertion Length". Install the fitting on the hose so that the mark is even with the end of the ferrule. Crimp the entire length of the ferrule to the Crimp Diameter given in the table.
Understand how event streaming fits in the big data ecosystem Explore Pulsar producers, consumers, and readers for writing and reading events Build scalable data pipelines by connecting Pulsar with external systems Simplify event-streaming application building with Pulsar Functions Manage Pulsar to perform monitoring, tuning .
Agilent 1290 Infinity X Agilent G1888A Agilent 7673A X Agilent 7683A X Agilent HS7694 Agilent 7695A Agilent 79855(A) X Agilent 5880 X Agilent 5890 X . Autosampler Compatibility Chart Crimp Neck ND8 1 1. Snap Ring ND11 Screw Neck ND13 Shell Vials Shell Vials Shell Vials Shell Vials Headspa
M39012/20-0504 D VIa Econo-Crimp 10-10005-006 3 Straight Cable Plugs (M39012/16) M39012 P/N Category Cable Group Cable Attachment Automatic P/N Figure M39012/16-0013 C VIa Econo-Crimp 10-01009-001 1 M39012/16-0014 C VIb Econo-Crimp 10-01009-002 1 M39012/16-0015 (1) C VIIa Econo-Crimp 10-01009-003 1 M39012/16-0016 C IV Econo-Crimp 10-01009-004 1 .
4 Parker Hannifin Corporation Hydraulic Valve Division Elyria, Ohio, USA Pulsar HY14-0108.indd, dd V Cylinder Port Options Spool Flow Rating Spool Positions Continued on Next Page low side of compensator settings. Code Description 0 None 1 12V Pulsar with 12" flying leads 2 12V 75 Hz Pulsar with 12" flying leads
N Male Crimp Plug S G T RFN-1005-3C 21 N Male Crimp Plug (Quick Disconnect) S G T RFN-1005-5 22 N Male Right Angle Crimp Plug S G T RFN-1009-C 23 N Male Right Angle Crimp Plug, Square Body S G T RFN-1009-C-03 24 N Female Chassis, 4-Hole
Pneumatic Crimper Maintaining the Quick Crimp Pneumatic The internal operating parts of the Quick Crimp Pneumatic Crimper are factory lubricated and do not Replacement guide plate with nutrequire additional maintenance. A grease fitting is supplied so you can grease the roller assembly periodically. If you are using the B-crimp die set, the
be a concise, but not superficial, treatment on GUI programming. Part III contains information on the features of Python that allow you to accomplish big things with surprisingly little code. In preparing this book the Python documentation atwww.python.orgwas indispensable. This book was composed entirely in LATEX.
