PROTECTION HISTORY DISPLAY MODE 2015 2014-15 2013-14
PROTECTION HISTORY DISPLAY 20CIClick on model for information on how to access the “Protection History Display Mode”CLICK HERE TO RETURN TO MODEL INFO. INDEX1
20152
AVR-X7200WA – AVR-X7200W – AVR-X6200W – AVR-X5200W – AVR-X4200W (1 of 3)POWERProcedure to enter the “Protection History Display Mode”1. Hold down buttons "STATUS" and "ZONE3 SOURCE" at the same time and press the power button to turn on the power.2. Select "PROTECTION" using the "CURSOR “ button, and press the "ENTER" button.3. Press the "STATUS" button and the unit will display the Protection History condition.PROTECTION HISTORY DISPLAY MODECLEARING THE PROTECTION HISTORY3
AVR-X7200WA – AVR-X7200W – AVR-X6200W – AVR-X5200W – AVR-X4200W (2 of 3)Protection History Display ModeThis mode records and displays an event in which the THERMAL, CURRENT, ASO or DC protection was activated.If protections have been activated multiple times, the latest protection operation is recorded.Procedure to enter the “Protection History Display Mode”.1. Hold down buttons "STATUS" and "ZONE3 SOURCE" at the same time and press the power button to turn on the power.2. Select "PROTECTION" using the "CURSOR “ button, and press the "ENTER" button.3. Press the "STATUS" button and the unit will display the Protection History condition.1. If no protections have occurred, “No Protect” is displayed2. if last protection was ASO, “ASO” is ent DisplayL1Line 1L2Line 2HISECTTORYOCause: A short circuit occurred between the speaker terminals, or speakers with an impedance outside the rating were connected. If the power is turned on during thisabnormality, protection is activated after around 6 seconds and the power is turned off.3. If the last protection was DC, “DC” is displayed.FLDL2:DCCause: DC output of the power amplifier is abnormal.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.4. If the last protection was THERMAL(E) or THERMAL(F),“THERMAL E or THERMAL F” is displayed.FLDL2:THERMALEFLDL2:THERMALFCause: Abnormal heat sink temperature.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.5. When the last protection incident was CURRENT protection,“CURRENT” is displayedFLDL2:CURRENTCaution: These protections may also be activated due to causes such as disconnection of connectors or operations around the microcomputer.If the power is turned on during this abnormality, protection is activated after around 2 minutes and the power is turned off.After viewing the above protection history, press the button "STATUS" to return to the normal display.FRONT PANEL – BUTTONS LOCATIONCLEARING THE PROTECTION HISTORY4
AVR-X7200WA – AVR-X7200W – AVR-X6200W – AVR-X5200W – AVR-X4200W (3 of 3)Clearing the Protection HistoryIf the unit is in “Protection History Display Mode”, just press and hold the “ENTER” button for 3 seconds. Note: If you do not mind erasing your settings from this unit, you canalso “Initialized/Micro Reset the unit to clear the Protection History from the unit’s memory.If the unit is not in “Protection History Display Mode”, enter the “Protection History Display Mode”:Hold down buttons "STATUS" and "ZONE3 SOURCE" at the same time and press the power button to turn on the power.Select the "2. PROTECTION" using the button "CURSOR ", and press the "ENTER" button.Press the "STATUS" button and the unit will display the Protection History condition.L1PROL2:DCFLDL2:FLDL2:Press and hold "ENTER" for 3 seconds.FLDPress and hold "ENTER" for 3 seconds and “CLEAR” is displayedfollowed by “NO PROTECT”. The unit’s Protection History is nowcleared.NOTEPCTCLROHIEARTECSTORYTWarning Displays by POWER LEDIf the power is turned off while a protection is detected, the POWER LED (red) flashes in the following ways as a warning according to the protection status.(a) ASO/DC protection: Flashes in 0.5-second cycles (0.25 seconds lit, 0.25 seconds unlit)(b) THERMAL (E/F) protection: Flashes in 2-second cycles (1 seconds lit, 1 seconds unlit)(c) CURRENT protection: Flashes in 4-second cycles (2 seconds lit, 2 seconds unlit)FRONT PANEL BUTTONS LOCATIONPROTECTION HISTORY DISPLAY MODE5
AVR-X3200W (1 of 3)Procedure to enter the “Protection History Display Mode”.1. Hold down buttons "ZONE2 SOURCE“, “DIMMER” and “STATUS” at the same time and press the power button to turn on the power.2. Select "PROTECTION" using the “TUNER PRESET CH /-“ button, and press the “STATUS" button.3. Press the "STATUS" button again and the unit will display the Protection History condition.PROTECTION HISTORY DISPLAY MODECLEARING THE PROTECTION HISTORY6
AVR-X3200W (2 of 3)Protection History Display ModeThis mode records and displays an event in which the THERMAL, CURRENT, ASO or DC protection was activated.If protections have been activated multiple times, the latest protection operation is recorded.Procedure to enter the “Protection History Display Mode”.1. Hold down buttons "ZONE2 SOURCE“, “DIMMER” and “STATUS” at the same time and press the power button to turn on the power.2. Select "PROTECTION" using the “TUNER PRESET CH /-“ button, and press the “STATUS" button.3. Press the "STATUS" button again and the unit will display the Protection History condition.1. If no protections have occurred, “No Protect” is displayedFLDNO2. if last protection was ASO, “ASO” is displayed.FLDPRTPROT:ASOECFLDFluorescent DisplayPRTProtectionTCause: A short circuit occurred between the speaker terminals, or speakers with an impedance outside the rating were connected.DC output of the power amplifier is abnormal.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.3. If the last protection was DC, “DC” is displayed.FLDPRT:DCCause: DC output of the power amplifier is abnormal.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.4. If the last protection was THERMAL(A), THERMAL(E) orTHERMAL(F), “THERMAL A, THERMAL E or THERMAL F” HERMALFCause: Abnormal heat sink temperature.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.5. When the last protection incident was CURRENT protection,:CURRENTFLD“CURRENT” is displayedCaution : These protections may also be activated due to other factors such as disconnection of connectors or operationsaround the microcomputer.After viewing the above protection history, press the "STATUS" button to return to the normal display.If the power is turned on in the abnormal state, protection is activated after around 2 minutes and the power is turned off.FRONT PANEL – BUTTONS LOCATIONCLEARING THE PROTECTION HISTORY7
AVR-X3200W (3 of 3)Clearing the Protection HistoryIf the unit is in “Protection History Display Mode”, just press and hold the “ENTER” button for 3 seconds. Note: If you do not mind erasing your settings from this unit, you canalso “Initialized/Micro Reset the unit to clear the Protection History from the unit’s memory.If the unit is not in “Protection History Display Mode”, enter the “Protection History Display Mode”:1. Hold down buttons "ZONE2 SOURCE“, “DIMMER” and “STATUS” at the same time and press the “POWER” button to turn on the power.2. Select "PROTECTION" using the “TUNER PRESET CH /-“ buttons, and press the “STATUS" button.3. Press the "STATUS" button again and the unit will display the Protection History condition.Press and hold the “DIMMER" button for 3 seconds.Press and hold the “DIMMER“ button again for 3 seconds and“CLEAR” is displayed followed by “NO PROTECT”. The unit’sProtection History is now cleared.FLDPRT:DCFLDPRT:CLEARFLDNOPROTECTWarning Displays by POWER LEDIf the power is turned off while a protection is detected, the POWER LED (red) flashes in the following ways as a warning according to the protection status.(a) ASO/DC protection: Flashes in 0.5-second cycles (0.25 seconds lit, 0.25 seconds unlit)(b) THERMAL (E/F) protection: Flashes in 2-second cycles (1 seconds lit, 1 seconds unlit)(c) CURRENT protection: Flashes in 4-second cycles (2 seconds lit, 2 seconds unlit)FRONT PANEL BUTTONS LOCATIONPROTECTION HISTORY DISPLAY MODE8
AVR-X2200W (1 of 3)Procedure to enter the “Protection History Display Mode”.1. Hold down buttons "ZONE2 SOURCE“, “DIMMER” and “STATUS” at the same time and press the power button to turn on the power.2. Select "PROTECTION" using the “TUNER PRESET CH /-“ button, and press the “STATUS" button.3. Press the "STATUS" button again and the unit will display the Protection History condition.PROTECTION HISTORY DISPLAY MODECLEARING THE PROTECTION HISTORY9
AVR-X2200W (2 of 3)Protection History Display ModeThis mode records and displays an event in which the THERMAL, CURRENT, ASO or DC protection was activated.If protections have been activated multiple times, the latest protection operation is recorded.Procedure to enter the “Protection History Display Mode”.1. Hold down buttons "ZONE2 SOURCE“, “DIMMER” and “STATUS” at the same time and press the power button to turn on the power.2. Select "PROTECTION" using the “TUNER PRESET CH /-“ button, and press the “STATUS" button.3. Press the "STATUS" button again and the unit will display the Protection History condition.1. If no protections have occurred, “No Protect” is displayedFLDNO2. if last protection was ASO, “ASO” is displayed.FLDPRTPROT:ASOECFLDFluorescent DisplayPRTProtectionTCause: A short circuit occurred between the speaker terminals, or speakers with an impedance outside the rating were connected.DC output of the power amplifier is abnormal.Note: A short circuit occurred between the speaker terminals, or speakers with an impedance outside the rating were connected.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.3. If the last protection was DC, “DC” is displayed.FLDPRT:DCCause: DC output of the power amplifier is abnormal.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.4. If the last protection was THERMAL(A), THERMAL(E) orTHERMAL(F), “THERMAL A, THERMAL E or THERMAL F” HERMALEFLDPRT:THERMALFCause: Abnormal heat sink temperature.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.5. When the last protection incident was CURRENT protection,:CURRENTFLD“CURRENT” is displayedCaution : These protections may also be activated due to other factors such as disconnection of connectors or operationsaround the microcomputer. After viewing the above protection history, press the "STATUS" button to return to the normal display.FRONT PANEL – BUTTONS LOCATIONCLEARING THE PROTECTION HISTORY10
AVR-X2200W (3 of 3)Clearing the Protection HistoryIf the unit is in “Protection History Display Mode”, just press and hold the “ENTER” button for 3 seconds. Note: If you do not mind erasing your settings from this unit, you canalso “Initialized/Micro Reset the unit to clear the Protection History from the unit’s memory.If the unit is not in “Protection History Display Mode”, enter the “Protection History Display Mode”:1. Hold down buttons "ZONE2 SOURCE“, “DIMMER” and “STATUS” at the same time and press the “POWER” button to turn on the power.2. Select "PROTECTION" using the “TUNER PRESET CH /-“ buttons, and press the “STATUS" button.3. Press the "STATUS" button again and the unit will display the Protection History condition.Press and hold the “DIMMER" button for 3 seconds.Press and hold the “DIMMER“ button again for 3 seconds and“CLEAR” is displayed followed by “NO PROTECT”. The unit’sProtection History is now cleared.FLDPRT:DCFLDPRT:CLEARFLDNOPROTECTWarning Displays by POWER LEDIf the power is turned off while a protection is detected, the POWER LED (red) flashes in the following ways as a warning according to the protection status.(a) ASO/DC protection: Flashes in 0.5-second cycles (0.25 seconds lit, 0.25 seconds unlit)(b) THERMAL (A/B) protection: Flashes in 2-second cycles (1 seconds lit, 1 seconds unlit)FRONT PANEL BUTTONS LOCATIONPROTECTION HISTORY DISPLAY MODE11
AVR-X1200W (1 of 3)Procedure to enter the “Protection History Display Mode”.1. Hold down buttons "ZONE2 SOURCE“, “DIMMER” and “STATUS” at the same time and press the power button to turn on the power.2. Select "PROTECTION" using the “TUNER PRESET CH /-“ button, and press the “STATUS" button.3. Press the "STATUS" button again and the unit will display the Protection History condition.PROTECTION HISTORY DISPLAY MODECLEARING THE PROTECTION HISTORY12
AVR-X1200W (2 of 3)Protection History Display ModeThis mode records and displays an event in which the THERMAL, CURRENT, ASO or DC protection was activated.If protections have been activated multiple times, the latest protection operation is recorded.Procedure to enter the “Protection History Display Mode”.1. Hold down buttons "ZONE2 SOURCE“, “DIMMER” and “STATUS” at the same time and press the power button to turn on the power.2. Select "PROTECTION" using the “TUNER PRESET CH /-“ button, and press the “STATUS" button.3. Press the "STATUS" button again and the unit will display the Protection History condition.1. If no protections have occurred, “No Protect” is displayedFLDNO2. if last protection was ASO, “ASO” is displayed.FLDPRTPROT:ASOECFLDFluorescent DisplayTCause: A short circuit occurred between the speaker terminals, or speakers with an impedance outside the rating were connected.DC output of the power amplifier is abnormal.Note: A short circuit occurred between the speaker terminals, or speakers with an impedance outside the rating were connected.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.3. If the last protection was DC, “DC” is displayed.FLDPRT:DCCause: DC output of the power amplifier is abnormal.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.4. If the last protection was THERMAL(A), THERMAL(E) orTHERMAL(F), “THERMAL A, THERMAL E or THERMAL F” isdisplayed.FLDPRT:THERMALAFLDPRT:THERMALBCause: Abnormal heat sink temperature.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.5. When the last protection incident was CURRENT protection,“CURRENT” is displayedFLD:CURRENTCaution : These protections may also be activated due to other factors such as disconnection of connectors or operationsaround the microcomputer.After viewing the above protection history, press the "STATUS" button to return to the normal display.FRONT PANEL – BUTTONS LOCATIONCLEARING THE PROTECTION HISTORY13
AVR-X1200W (3 of 3)Clearing the Protection HistoryIf the unit is in “Protection History Display Mode”, just press and hold the “ENTER” button for 3 seconds. Note: If you do not mind erasing your settings from this unit, you canalso “Initialized/Micro Reset the unit to clear the Protection History from the unit’s memory.If the unit is not in “Protection History Display Mode”, enter the “Protection History Display Mode”:1. Hold down buttons "ZONE2 SOURCE“, “DIMMER” and “STATUS” at the same time and press the “POWER” button to turn on the power.2. Select "PROTECTION" using the “TUNER PRESET CH /-“ buttons, and press the “STATUS" button.3. Press the "STATUS" button again and the unit will display the Protection History condition.Press and hold the “DIMMER" button for 3 seconds.Press and hold the “DIMMER“ button again for 3 seconds and“CLEAR” is displayed followed by “NO PROTECT”. The unit’sProtection History is now cleared.FLDPRT:DCFLDPRT:CLEARFLDNOPROTECTWarning Displays by POWER LEDIf the power is turned off while a protection is detected, the POWER LED (red) flashes in the following ways as a warning according to the protection status.(a) ASO/DC protection: Flashes in 0.5-second cycles (0.25 seconds lit, 0.25 seconds unlit)(b) THERMAL (A/B) protection: Flashes in 2-second cycles (1 seconds lit, 1 seconds unlit)(c) CURRENT protection: Flashes at 4-second intervals (2 seconds lit, 2 seconds unlit)FRONT PANEL BUTTONS LOCATIONPROTECTION HISTORY DISPLAY MODE14
AVR-S910W (1 of 3)TUNER PRESET CH-POWERTUNER PRESET CH TUNE-Procedure to enter the “Protection History Display Mode”.1. Hold down buttons “TUNER PRESET CH-”, “TUNE-” and “TUNER PRESET CH ” at the same time and press the power button to turn on the power.2. Select "PROTECTION" using the “TUNER PRESET CH /-“ button, and press the “STATUS" button.3. Press the "STATUS" button again and the unit will display the Protection History condition.PROTECTION HISTORY DISPLAY MODECLEARING THE PROTECTION HISTORY15
AVR-S910W (2 of 3)Protection History Display ModeThis mode records and displays an event in which the THERMAL, CURRENT, ASO or DC protection was activated.If protections have been activated multiple times, the latest protection operation is recorded.Procedure to enter the “Protection History Display Mode”.1. Hold down buttons “TUNER PRESET CH-”, “TUNE-” and “TUNER PRESET CH ” at the same time and press the power button to turn on the power.2. Select "PROTECTION" using the “TUNER PRESET CH /-“ button, and press the “STATUS" button.FLD3. Press the "STATUS" button again and the unit will display the Protection History condition.1. If no protections have occurred, “No Protect” is displayedFLDNO2. if last protection was ASO, “ASO” is displayed.FLDPRTPROT:ASOECFluorescent DisplayTCause: A short circuit occurred between the speaker terminals, or speakers with an impedance outside the rating were connected.DC output of the power amplifier is abnormal.Note: A short circuit occurred between the speaker terminals, or speakers with an impedance outside the rating were connected.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.3. If the last protection was DC, “DC” is displayed.FLDPRT:DCCause: DC output of the power amplifier is abnormal.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.4. If the last protection was THERMAL(A), THERMAL (B),THERMAL(E) or THERMAL(F), “THERMAL A, THERMAL (B),THERMAL E or THERMAL F” is RMALEFLDPRT:THERMALFCause: Abnormal heat sink temperature.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.5. When the last protection incident was CURRENT protection,“CURRENT” is displayedFLD:CURRENTCaution : These protections may also be activated due to other factors such as disconnection of connectors or operationsaround the microcomputer. After viewing the above protection history, press the "STATUS" button to return to the normal display.FRONT PANEL – BUTTONS LOCATIONCLEARING THE PROTECTION HISTORY16
AVR-S910W (3 of 3)Clearing the Protection HistoryIf the unit is in “Protection History Display Mode”, just press and hold the “ENTER” button for 3 seconds. Note: If you do not mind erasing your settings from this unit, you canalso “Initialized/Micro Reset the unit to clear the Protection History from the unit’s memory.If the unit is not in “Protection History Display Mode”, enter the “Protection History Display Mode”:1. Hold down buttons “TUNER PRESET CH-”, “TUNE-” and “TUNER PRESET CH ” at the same time and press the power button to turn on the power.2. Select "PROTECTION" using the “TUNER PRESET CH /-“ button, and press the “STATUS" button.3. Press the "STATUS" button again and the unit will display the Protection History condition.Press and hold the “DIMMER" button for 3 seconds.Press and hold the “DIMMER“ button again for 3 seconds and“CLEAR” is displayed followed by “NO PROTECT”. The unit’sProtection History is now cleared.FLDPRT:DCFLDPRT:CLEARFLDNOPROTECTWarning Displays by POWER LEDIf the power is turned off while a protection is detected, the POWER LED (red) flashes in the following ways as a warning according to the protection status.(a) ASO/DC protection: Flashes in 0.5-second cycles (0.25 seconds lit, 0.25 seconds unlit)(b) THERMAL (A/B) protection: Flashes in 2-second cycles (1 seconds lit, 1 seconds unlit)FRONT PANEL BUTTONS LOCATIONPROTECTION HISTORY DISPLAY MODE17
AVR-S710W (1 of 3)TUNER PRESET CH-POWERTUNER PRESET CH TUNE-Procedure to enter the “Protection History Display Mode”.1. Hold down buttons “TUNER PRESET CH-”, “TUNE-” and “TUNER PRESET CH ” at the same time and press the power button to turn on the power.2. Select "PROTECTION" using the “TUNER PRESET CH /-“ button, and press the “STATUS" button.3. Press the "STATUS" button again and the unit will display the Protection History condition.PROTECTION HISTORY DISPLAY MODECLEARING THE PROTECTION HISTORY18
AVR-S710W (2 of 3)Protection History Display ModeThis mode records and displays an event in which the THERMAL, CURRENT, ASO or DC protection was activated.If protections have been activated multiple times, the latest protection operation is recorded.Procedure to enter the “Protection History Display Mode”.1. Hold down buttons “TUNER PRESET CH-”, “TUNE-” and “TUNER PRESET CH ” at the same time and press the power button to turn on the power.2. Select "PROTECTION" using the “TUNER PRESET CH /-“ button, and press the “STATUS" button.FLD3. Press the "STATUS" button again and the unit will display the Protection History condition.1. If no protections have occurred, “No Protect” is displayedFLDNO2. if last protection was ASO, “ASO” is displayed.FLDPRTPROT:ASOECFluorescent DisplayTCause: A short circuit occurred between the speaker terminals, or speakers with an impedance outside the rating were connected.DC output of the power amplifier is abnormal.Note: A short circuit occurred between the speaker terminals, or speakers with an impedance outside the rating were connected.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.3. If the last protection was DC, “DC” is displayed.FLDPRT:DCCause: DC output of the power amplifier is abnormal.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.4. If the last protection was THERMAL(A), THERMAL(E) orTHERMAL(F), “THERMAL A, THERMAL E or THERMAL F” isdisplayed.FLDPRT:THERMALAFLDPRT:THERMALBCause: Abnormal heat sink temperature.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.5. When the last protection incident was CURRENT protection,“CURRENT” is displayedFLD:CURRENTCaution : These protections may also be activated due to other factors such as disconnection of connectors or operationsaround the microcomputer.After viewing the above protection history, press the "STATUS" button to return to the normal display.FRONT PANEL – BUTTONS LOCATIONCLEARING THE PROTECTION HISTORY19
AVR-S710W (3 of 3)Clearing the Protection HistoryIf the unit is in “Protection History Display Mode”, just press and hold the “ENTER” button for 3 seconds. Note: If you do not mind erasing your settings from this unit, you canalso “Initialized/Micro Reset the unit to clear the Protection History from the unit’s memory.If the unit is not in “Protection History Display Mode”, enter the “Protection History Display Mode”:1. Hold down buttons “TUNER PRESET CH-”, “TUNE-” and “TUNER PRESET CH ” at the same time and press the power button to turn on the power.2. Select "PROTECTION" using the “TUNER PRESET CH /-“ button, and press the “STATUS" button.3. Press the "STATUS" button again and the unit will display the Protection History condition.Press and hold the “DIMMER" button for 3 seconds.Press and hold the “DIMMER“ button again for 3 seconds and“CLEAR” is displayed followed by “NO PROTECT”. The unit’sProtection History is now cleared.FLDPRT:DCFLDPRT:CLEARFLDNOPROTECTWarning Displays by POWER LEDIf the power is turned off while a protection is detected, the POWER LED (red) flashes in the following ways as a warning according to the protection status.(a) ASO/DC protection: Flashes in 0.5-second cycles (0.25 seconds lit, 0.25 seconds unlit)(b) THERMAL (A/B) protection: Flashes in 2-second cycles (1 seconds lit, 1 seconds unlit)(c) CURRENT protection: Flashes at 4-second intervals (2 seconds lit, 2 seconds unlit)FRONT PANEL BUTTONS LOCATIONPROTECTION HISTORY DISPLAY MODE20
AVR-S510BT/AVR-S500BT (1 of 3)Procedure to enter the “Protection History Display Mode”.To enter the “Protection History Display Mode”, the unit has to be set to “Product Mode” first.1. Hold down buttons “SOUND MODE ”, “TUNER PRESET CH-” and “TUNER PRESET CH ” at the same time for approx. 3 seconds while the power is on. Theunit enters the “PRODUCT MODE” (Remote Lock, Tuner Step Change, OSD Update, Protection History Display, or Mic Mode) and the “REMOTE LOCKMODE” is first displayed.2. Press the “TUNE-” button repeatedly to switch modes until “Protection History Mode” is displayed.PROTECTION HISTORY DISPLAY MODECLEARING THE PROTECTION HISTORY21
AVR-S510BT/AVR-S500BT (2 of 3)Protection History Display ModeThis mode records and displays an event in which the THERMAL, CURRENT, ASO, DC or POWER protection was activated.FLDFluorescent DisplayIf protections have been activated multiple times, the latest protection operation is recorded.Procedure to enter the “Protection History Display Mode”.PRTProtectionTo enter the “Protection History Display Mode”, the unit has to be set to “Product Mode” first.1. Hold down buttons “SOUND MODE ”, “TUNER PRESET CH-” and “TUNER PRESET CH ” at the same time for approx. 3 seconds while the power is on. The unit enters the“PRODUCT MODE” (Remote Lock, Tuner Step Change, OSD Update, Protection History Display, or Mic Mode) and the “REMOTE LOCK MODE” is first displayed.2. Press the “TUNE-” button repeatedly to switch modes until “Protection History Mode” is displayed.1. If no protections have occurred, “No Protect” is displayedFLDNO2. If the last protection was THERMAL(A) or THERMAL(B), “THERMAL A orTHERMAL B” is ause: Abnormal heat sink temperature.If the power is turned on during this abnormality, protection is activated after around 4 seconds and the power is turned off.3. if last protection was ASO, “ASO” is displayed.FLDPRT:ACause: A short circuit occurred between the speaker terminals, or speakers with an impedance outside the rating were connected.As the excess current is detected after operation of the speaker relay, a short on the speaker terminal and the connected speaker can be identified.4. If the last protection was DC, “DC” is displayed.FLDPRT:DCCause: DC output of the power amplifier is abnormal.If the power is turned on during this abnormality, protection is activated after around 6 seconds and the power is turned off.5. When the last protection incident was POWER protection, “POWER” isdisplayed.FLDPRT:PowerCause: The Power Supply ( 12V) is abnormal.Caution : These protections may also be activated due to other factors such as disconnection of connectors or operationsaround the microcomputer.After viewing the above protection history, press the “PRESET" button to return to the normal display.FRONT PANEL – BUTTONS LOCATIONCLEARING THE PROTECTION HISTORY22
AVR-S510BT/AVR-S500BT (3 of 3)Clearing the Protection HistoryIf the unit is in “Protection History Display Mode”, just press and hold the “PRESET” button for 3 seconds. Note: If you do not mind erasing your settings from this unit, you canalso “Initialized/Micro Reset the unit to clear the Protection History from the unit’s memory.If the unit is not in “Protection History Display Mode”, enter the “Protection History Display Mode”:To enter the “Protection History Display Mode”, the unit has to be set to “Product Mode” first.1. Hold down buttons “SOUND MODE ”, “TUNER PRESET CH-” and “TUNER PRESET CH ” at the same time for approx. 3 seconds while the power is on. The unit enters the“PRODUCT MODE” (Remote Lock, Tuner Step Change, OSD Update, Protection History Display, or Mic Mode) and the “REMOTE LOCK MODE” is first displayed.2. Press the “TUNE-” button repeatedly to switch modes until “Protection History Mode” is displayed.Press and hold the “PRESET" button for 3 seconds.Press and hold the “PRESET“ button again for 3 seconds and “CLEAR”is displayed followed by “NO PROTECT”. The unit’s Protection Historyis now cleared.FRONT PANEL BUTTONS LOCATIONFLDPRT:DCFLDPRT:CLEARFLDNOPROTECPROTECTION HISTORY DISPLAY MODET23
2014 - 201524
AVR-X4100W (1 of 3)Procedure to enter the “Protection History Display Mode”.1. Hold down buttons "STATUS" and "ZONE3 SOURCE" at the same time and press the power button to turn on the power.2. Select "PROTECTION" using the "CURSOR “ buttons, and press the "ENTER" button.3. Press the "STATUS" button and the unit will display the Protection History condition.PROTECTION HISTORY DISPLAY MODECLEARING THE PROTECTION HISTORY25
AVR-X4100W (2 of 3)Protection History Display ModeThis mode records and displays an event in which the THERMAL, CURRENT, ASO or DC protection was
AVR-1912. AVR-1712. AVR-1612. AVR-1312. 2011. PROTECTION HISTORY DISPLAY MODE. 1. Click on model for information o
RESUME WITH - a command that allows you to back up if you misspeak or change your mind after dictating a phrase. . Not sure how to spell a specific name or technical term? Try using Spell Mode. [Mode-Name] MODE ON or START [Mode-Name] MODE - Turn a mode on. [Mode-Name] MODE OFF or STOP [Mode-Name] MODE - Turn a mode off.
Lantern On/Off Press the Lantern Standby Power Button once to cycle through four settings: Mode 1: OFF Mode 2: 360 Mode 3: 180 - side 1 Mode 4: 180 - side 2 Lantern Mode Press the Mode Button once to cycle through five modes: Mode 1: Warm White Light Mode 2: Red Light Mode 3: Color Fade Mode 4: Music Sync Colors Mode 5: Emergency .
2015 2015 2015 2015 2015 2015 2015 2015 2015 2015 2015 2015 2015 2015 2015 2015 . Removal handle Sound output / wax protection system. 11 Virto V-10 Custom made shell Battery door Volume control (optional) Push button Removal handle . Before using
In the riding mode after 5 seconds, display 2 automatically returns to display 1. In display 1, the original motor power is replaced by motor running temperature as is shown in Figure. Display 3 ： In display 2, hold button (SW ) shortly to enter display 3. Display 3 The followings are shown on display 3.
MODE display Displays the current mode, including: AUTO COOL DRY HEAT FAN Transmission Indicator Lights up when the remote sends a signal to indoor unit ON/OFF display Appears when the unit is turned on, and disappears when it is turned off TIMER ON display Displays when TIMER ON is set TIMER OFF display OFF is set SLEEP display Battery display
1.4.Using of the Digital SCX Chronometer 1.4.1.Display Race Information after a race - press for 2 sec MODE, 5 x MODE - display is showing RES - press SELECT, display shows fastest lap of each driver - press SELECT, display shows average lap time of each driver - press SELECT, display shows the duration of the whole race - press SELECT, display shows the time, lap distance for each
Sabbath Mode To activate SABBATH mode, open door and pres SAB button. If display lighting was activated, it will remain activated. Turn off display lighting before initiating Sabbath Mode if display light will not be used. When in Sabbath mode: † The display will be switched off (with the exclusion of the measurement temperature icon LED);
6-bits, 16-bits, 18-bits RGB interface 3-pin/4-pin serial interface Display mode: Full color mode (idle mode off): 262K-colors Reduced color mode (idle mode on): 8-colors (3-bits MSB bits mode) On chip functions: VCOM generator and adjustment Timing generator Oscillator DC/DC converter 4 preset gamma curve selectable Line/frame inversion
