Fluorescent Dimming Ballasts Hi-lume 1% Architectural
Fluorescent Dimming BallastsHi-lume 1%Architectural DimmingHi-lume (1) 07.08.04Hi-lume OverviewHi-lume architectural electronic dimming ballastsare designed to meet the most demandinglighting requirements. By providing industryleading performance with true full-range 100%to 1% fluorescent dimming, Hi-lume ballasts enableyou to provide the ideal visual environment for anyapplication.Hi-lume, case type A3.00”w (76mm) x 1.00”h (25mm) x 4.90”l (124mm)Features Continuous, flicker-free dimming from 100% to 1% Standard 3-wire line-voltage phase-controltechnology for consistent fixture-to-fixturedimming performance Models available for T4 triple-tube compact,T5-HO linear, and T8 lamps Programmed rapid start design preheats lampcathodes before applying full arc voltage Lamps turn on to any dimmed level withoutflashing to full brightness Low harmonic distortion throughout the entiredimming range maintains power quality Frequency of operation ensures that ballastdoes not interfere with infrared devices operatingbetween 38 and 42 kHz Inrush current limiting circuitry eliminates circuitbreaker tripping, switch arcing, and relay failure End-of-lamp-life protection circuitry (for T4and T5-HO models) ensures safe operationthroughout entire lamp life cycle For linear lamps, ballasts maintain consistentlight output for different lamp lengths, ensuringfixture uniformity Ultra-quiet operation Protected from miswires of any input power tocontrol lead, or from lamp leads to each otherand/or ground 100% compatible with all Lutron 3-wirefluorescent controls 100% performance tested at factoryRS P E C I F I C AT I O N S U B M I T TA LJob Name:Job Number:Model Numbers:Hi-lume, case type C1.18”w (30mm) x 1.00”h (25mm) x 18.00”l (457mm)Hi-lume, case type F2.38”w (60mm) x 1.50”h (38mm) x 9.50”l (241mm) Designed and assembled in the USA 5-year limited warranty with Lutron field servicecommissioning (3-year standard warranty)from date of purchasePage
Fluorescent Dimming BallastsHi-lume 1%Architectural DimmingHi-lume (2) 07.08.04SpecificationsPerformanceStandards Dimming Range: 100% to 1% measuredrelative light output (RLO) Lamp Starting: programmed rapid start Minimum Lamp Starting Temperature: 10 C (50 F) Ambient Temperature Operating Range: 10 C(50 F) to 60 C (140 F) Relative Humidity: maximum 90% noncondensing Operating Voltage: 120V or 277V at 60Hz Lamp Current Crest Factor: less than 1.7 Lamp Flicker: none visible Light Output Variation: constant 2% light outputfor line voltage variations of 10% Lamp Life: average lamp life meets or exceedsrating of lamp manufacturer Ballast Factor: greater than .85 for T8 lamps,greater than .95 for T4 lamps, equal to 1.0 forT5-HO lamps Power Factor: greater than .95 Total Harmonic Distortion (THD): less than 10% Maximum Inrush Current: 7 amps per ballast at120V, 3 amps per ballast at 277V Sound Rating: Inaudible in a 27dBa ambient Maximum Ballast Case Temperature: 75 C (167 F)RS P E C I F I C AT I O N S U B M I T TA LJob Name:Job Number:Model Numbers: UL Listed (evaluated to the requirementsof UL935) CSA certified (evaluated to the requirementsof C22.2 No. 74) Class P thermally protected Meets ANSI C82.11 High Frequency BallastStandard Meets FCC Part 18 Non-Consumer requirementsfor EMI/RFI emissions T4 and T5-HO ballasts are MIL Std. 461Ecompliant (meets the requirements of CE101,RE101 and RE102) Meets ANSI C62.41 Category A surge protectionstandards up to and including 6kV Manufacturing facilities employ ESD reductionpractices that comply with the requirementsof ANSI/ESD S20.20 Lutron Quality Systems registered to ISO9001.2000Page
Hi-lume 1%Fluorescent Dimming BallastsArchitectural DimmingHi-lume (3) 07.08.04Hi-lume Ballast Models120 VOLTSLampTypeT4 triple-tube4-pin277 VOLTSLampWatts(length)LampsperballastCase BallastType Current(amps)Hi-lumeModel Number 1BallastCurrent(amps)Hi-lumeModel Number �)1F.88FDB-9680-120-1----1/2” diameterT5-HO linearhigh output5/8” diameterT8 linearand U-bent1” diameterT12 linear HO(800ma)1½” diameter1Mounting studs standard for T4 ballasts. Delete suffix -S in the model number if mounting studs not needed.RS P E C I F I C AT I O N S U B M I T TA LJob Name:Job Number:Model Numbers:Page
Hi-lume 1%Fluorescent Dimming BallastsArchitectural DimmingHi-lume (4) 07.08.04Case DimensionsA18-32 Threaded Stud0.29” (.736mm)ABFGABCDEFGHI4.20” (107 mm)1.00” (25 mm)3.00” (76 mm)4.90” (124 mm)4.60” (117 mm)(mounting centers)2.00” (51 mm)1.08” (27 mm)1.60” (41 mm)1.39” (35 DCABEC(409 mm)(25 mm)(30 mm)(457 mm)(450 mm)(mounting centers)DFPower and controlwires are 18” (0.45m)A8.30”1.50”2.38”9.50”8.91”(211 mm)(38 mm)(60 mm)(241 mm)(226 mm)(slot mounting centers)BCABCDEEDIf using four hole mount,mounting centers are 9.21”(234 mm) x 1.70” (43 mm).Lamp wires are36” (0.90m)1Mounting studs standard. When ordering, delete suffix -S in theballast model number if mounting studs not needed.RS P E C I F I C AT I O N S U B M I T TA LJob Name:Job Number:Model Numbers:Page
Hi-lume 1%Fluorescent Dimming BallastsArchitectural DimmingHi-lume (5) 07.08.04Wiring DiagramsOne compact fluorescent lampBlack (Switched Hot)ToDimmingControl1Orange (Dimmed Hot)RedRed14-pinLamp HolderHi-lumeBlueNeutralGround 2Blue1 Dimmingcontrol wire colors do not necessarily match ballast wire colors(e.g. control “dimmed hot” may be yellow and ballast “dimmed hot” maybe orange). Wire colors shown are for Lutron controls and ballasts only.2 Ballast and lighting fixture must be effectively grounded.Note: For T4 compact lamps, maximum lamp-to-ballast wire length is 3 feet (1m).RS P E C I F I C AT I O N S U B M I T TA LJob Name:Job Number:Model Numbers:Page
Hi-lume 1%Fluorescent Dimming BallastsArchitectural DimmingHi-lume (6) 07.08.04Hi-lume Wiring DiagramsOne T5-HO or T8 lamp3Black (Switched Hot)ToDimmingControlOrange (Dimmed Hot)1NeutralFluorescent LampRed1Hi-lume DimmingBallastRedBlueBlueGround 2Two T5-HO or T8 lampsFluorescent LampRedBlack (Switched Hot)ToDimmingControlOrange (Dimmed Hot)311NeutralRedYellowHi-lume DimmingBallastBlueBlueGround 2YellowFluorescent Lamp3Fluorescent Lamp3Three T8 lampsRedBlack (Switched Hot)ToDimmingControlOrange (Dimmed Hot)NeutralYellow Red11Hi-lume DimmingBallastYellowBlue/WhiteBlueGround 2Fluorescent LampBlueBlue/WhiteFluorescent Lamp31Dimming control wire colors do not necessarily match ballast wire colors (e.g. control ‘dimmed hot’ may be yellow, andballast ‘dimmed hot’ may be orange. Wire colors shown are for Lutron ballasts and controls only.2 Ballast and lighting fixture must be effectively grounded.3 Includes 6” T8 U-bent lampsNote: For T5-HO and T8 lamps, maximum lamp-to-ballast wire length is 7 feet (2m).RS P E C I F I C AT I O N S U B M I T TA LJob Name:Job Number:Model Numbers:Page
Fluorescent Dimming BallastsHi-lume 1%Architectural DimmingHi-lume (7) 07.08.04Wiring and GroundingATTENTION ELECTRICIANSAND CONTRACTORSBallast/Socket LeadsLead lengths from ballast to socket must notexceed 7’ (2m) for T5-HO and T8 linear lamps,and 3’ (1m) for T4 compact lamps.All wiring from the dimming control to the Hi-lumeballasts is line voltage wiring and may be runtogether in the same conduit.Ballast and lighting fixture must be effectivelygrounded. Ballasts must be installed per nationaland local electrical codes.Number of Ballasts Per ControlLamp SocketsQuality lamp sockets are required to ensurepositive lamp-pin to socket contact. T5-HO linearlamps require rotary locking sockets. T8 lampsrequire knife-edge sockets. U-bent lamps requirelocking sockets and proper lamp support to holdlamp pins in full contact with the socket.To calculate the maximum number of ballastsallowed per control, divide control’s currentcapacity by individual ballast current. Certaincontrols allow a specific maximum number ofballasts.Lamp Mounting for T8Many fluorescent lamp sockets are available withmounting slots to vary the height of the lampaway from the grounded metal surface. Usethese slots to get the lamp glass to be 1/2" 1/4"away from the grounded metal surface.ATTENTIONFACILITIES MANAGERSPERFORMANCELamps Must Be SeasonedHaving a fluorescent lamp too close to thegrounded metal will make the minimumintensity too low and will reduce lamp life.Having a fluorescent lamp too far away fromthe grounded metal will make the lamp flickeror not turn on at all.New fluorescent lamps must be operated for100 hours at full output (“seasoned”) to renderlamp impurities inert, so as to achieve properdimming performance and average rated lamp life.Lamp Mounting for T4 and T5-HOReplacement PartsKeep lamps 3/8" 1/8” away from the groundedmetal surface.Use replacement parts with exact Lutron modelnumbers. Consult Lutron if you have anyquestions.Having a T5-HO lamp too close to the groundedmetal will not reduce lamp life but may cause avisible difference in brightness along the length ofthe lamp.Ballast Operating TemperatureBallast case temperature must not exceed 75 Cat any point on ballast.RSERVICEFurther InformationFor further information, please visit us atwww.lutron.com/ballasts or contact our 24-hourTechnical Support Center at 1-800-523-9466.Purchase by Visiting GoodMart.comor by Calling (877) 402-6100
3 f f f.30.57.82 fdb-4827-120-1 fdb-4827-120-2 fdb-4827-120-3.14.25.35 fdb-4827-277-1 fdb-4827-277-2 fdb-4827-277-3 40w (60”) 1 2 f f.36.64 fdb-6027-120-1 fdb-6027-120-2.16.30 fdb-6027-277-1 fdb-6027-277-2 t12 linear ho (800ma) 85w (72”) 1 f .75 fdb-7280-120-1 - - - - 95w (84”) 1 f .83 fdb-8480-120-1 - - - -File Size: 215KB
Logarithmic dimming to 1%. Refer to XPoint tech sheet. ECOS23,4,5 Lutron Hi-Lume 2-wire forward-phase driver. Minimum dimming level 1%. Minimum lumen 1000/Maximum lumen 3000. ECOS33,4 Lutron Hi-Lume 3-wire or EcoSystem dimming driver. Minimum dim-ming level 1%. Minimum lumen 1000/Maximum lumen 4500. SF Single fuse. Specify 120V or 277V.
ED 0-10V Dimming ED1 0-10V 1% Dimming EDD 0-10V Dim-to-Dark ESD Step Dimming LUTH Hi-lume 1% EcoSystem LED driver with Soft-on, Fade-to-Black dimming technology7 DALIP DALI Power Bus 8 U 120V-277V 347 347V (E, ED, ED1 only) ELL14 Emergency Battery Pack, 10W 9,10,11 ELL14H2 Emergency Battery Pack, 2-Hour Run Time 9,10,11 GLR Fast Blow Fuse
Total System Watts: 24W . Lutron Hi-Lume EcoSystem (LDE1) - 1% Dimming LH1 DALI 1% Dimming D11 . 1% Dimming CLM1 (3' minimum length. Increases height by 0.73" at module location. Compatible with Encelium X Light Management System.) WattstopperDLM - 1% Dimming DLM1 (3' minimum length.) Ceiling Configuration Std. 15/16" Lay-in or Std. 15/16 .
a ballast via a Head Extension ( up to 25ft long ). Jumper Cables link TRANS-FLO Ballasts together ( up to 10 in a series ). The TRANS-FLO SYSTEM operates in three modes: 1. INDIVIDUAL BALLAST DIMMING MODE ( two lamps ) 2. SERIES BALLAST DIMMING MODE (up to 10 ballasts per series ) 3. NON-DIM MODE
Type A Instant / Programmed Start Ballasts TCP’s DirecT8 tubes are the perfect replacement for old fluorescent lighting. Remove the existing T8 fluorescent and replace with DirecT8 Type A plug and play tubes. These tubes feature multiple ballast compatibility including Instant Start, Programmed Start, Rapid Start, and Dimmable ballasts.
SECTION 16511 & 16521 - INTERIOR & EXTERIOR LIGHTING Ballasts (Electronic Compact Fluorescent) Advance Smart Mate Aculite Lightolier Lutron Prescolite Ballasts (Electronic Rapid Start T-8 Fluorescent) Advance Optanium Bodine (For emergency lighti
Lutron E-3-T832-C-277-1 VEZ-132-SC Must be a complete dimming circuit replacement - including controls and dimming ballast. Philips dimensions are 9.5 x 1.7 x 1.18. Lutron dimensions are 18 x 1.18 x 1 inches. Electronic Fluorescent Mark 10 Powerline Lutron E-3-T832-C-277
API RP 505 «API RP 505 « Recommended Practice for classification of locations for ElectricalRecommended Practice for classification of locations for Electrical Installations at Petroleum facilities classified as Class I, zone 0, zone1, zone2 » Foreword states : « API publications may be used by anyone desiring to do so. Every effort has been made by the Institute to assure the accuracy and .
