Do-It-Yourself Aluminum Soffit & Fascia System
Do-It-YourselfAluminum Soffit & Fascia SystemLifetime WarrantyBaked-On Polyester FinishMaintenance-FreeProvides Needed Intake VentilationProtects & BeautifiesProfessional QualityArchitectural Profile
Sell-Even’s corrosion resistantsoffit panels control moistureand rotting problems common toeave and overhang areas, whilealso providing proper temperaturebalance and energy performance.Vented soffit panels resist theweathering of harsh winterswhile helping control ice dambuildup on roofing. In hotsummer climates they help tocontrol energy costs bylowering the interior attictemperature. Without properventilation, overhang areas areprone to moisture problemsand decrease the energyefficiency of insulation.Sturdy, lightweight, lowmaintenance panels are veryeasy to install. Each precisionformed panel interlocks withthe next to produce a finished,professional looking job.Sell-Even soffit panels providea practical low-cost system fornew home construction, andimprove the appearance ofolder homes.Long-lasting protectionBeauty Protects hard to maintain,tough to paint areas prone towater damage and decay Helps regulate attic areatemperatures Prevents moisture buildupthat can rot wood Keeps living areas morecomfortable with bettercirculation year-round Promotes a balancedventilation system Fourteen designer colors andmatching accessories Enhances home appearance Durable and attractive superpolycoat finishLow-maintenanceAvailable ColorsWHITEROYAL BROWNHICKORYHUNTER GREENALMONDGRAYSAND TONECOPPER PENNYEVERGREENCOFFEEKHAKISANDSTONEHERITAGE GRAYTERRA BRONZENOTE: Color swatches are for reference only. Limited by printing processesand viewing conditions, color swatches on this piece are not necessarilyaccurate. Actual color samples are available upon request. Will not rust, rot or split Never paint or scrape hardto-reach overhangs again Rinse clean with garden hoseSell-Even Building Produc tsAppleton Supply Co.1905 W. Haskell StreetAppleton, WI 54914(800) 558-3414www.appletonsupply.com
Fast & Easy Installation for New Constuction & RemodelingSoffit & Fascia Installation TipsHip Roof(4-way overhang)Do NOT Over Nail Fascia Trim. Recommended: One Nail Every 36 in.Fascia CornersCut bottom flange and bend 1” of end to make lapfold and form box at corner. Place next piece tooverlap and continue installation.Fascia trimFascia boardNail every 36 in. DO NOT drive nails tight!Double channelat cornersFrieze runner locationAlign top of channel to bottomedge of fascia board. Runentire length of wall.Frieze RunnerChannel(or J-Channel)Soffit panelsFIGURE 1Using frieze runner channel:* (Refer to Figure 1)1. FRIEZE RUNNER - Top edge of runner channel must be level andaligned with the bottom surface of the fascia board. Using nailing flangeof channel, nail and install along the entire length of the wall surface.2. DOUBLE-CHANNEL - To join panels at corners, cut double channel tofit and match angle when positioned diagonally from frieze channel tocorner of fascia board.3. SOFFIT PANELS - Cut at 45 for corner areas, slide into channel andsecure into position using nails in panel grooves as required, to underedge of fascia board. Continue panel installation for entire length.4. FASCIA TRIM - Beginning at corner, position up snug to underside of soffitpanels, pre-drill (align with soffit grooves) and nail through bottom lip offascia trim every 36” along bottom edge of fascia board. NEVER ‘face nail’fascia. DO NOT drive nails tight — fascia must be ‘hung’, not tight, to allowexpansion and help prevent distortion. Allow at least 1” overlap of fasciawhere lengths meet.5. FINISH TRIM - Use drip edge, gutter or all-purpose trim to cover and finishtop edge of fascia trim.* If installing soffit panels over existing wood soffits, soffit ‘J’ channel can beused in place of frieze runner and double channel.
Fast & Easy Installation for New Constuction & RemodelingSoffit & Fascia Installation TipsDo NOT Over Nail Fascia Trim. Recommended: One Nail Every 36 in.Gable End RoofFrieze Runner ChannelRefer to Fig 1 for position detail.Fascia TrimSupply Co.Fascia CornersRefer to Fig 1 detail.Fascia boardSoffit panelsFIGURE 2Using frieze runner channel:* (Refer to Figure 2)1. FRIEZE RUNNER - Top edge of runner channel must be level and alignedwith the bottom surface of the fascia board. Using nailing flange of channel,nail and install along the entire length of the wall surfaces and up to gablepeak on side wall.2. SOFFIT PANELS - gable end - Start installation at the base of the gableend working up to the peak as far as full panels will fit. Slide panels intochannel and secure into position using nails in panel grooves as required, tounder edge of fascia board. When both sides are done to this point, it maybe necessary to cut a panel, bend to match peak angle and rebend edges tomake interlocking jointings. Slide peak panel into position and nail.2a. SOFFIT PANELS - other sides - Starting from one end, slide into channeland secure into position using nails in panel grooves as required, to underedge of fascia board. Continue panel installation for entire side.Nail every 36 in.DO NOT drive nails tight!3. FASCIA TRIM - Beginning at corners, cut and bend to form box (see Fig 2),position up snug to underside of soffit panels, pre-drill (align with soffitgrooves) and nail through bottom lip of fascia trim every 36” along bottomedge of fascia board. NEVER ‘face nail’ fascia. DO NOT drive nails tight —fascia must be ‘hung’, only snug to soffit, to allow expansion and helpprevent distortion. Allow at least 1” overlap of fascia where lengths meet.Cover balance of gable end with fascia trim and cut to make overlap joint atpeak.4. FINISH TRIM - Use drip edge or all-purpose trim to cover and finish topedge of fascia trim.* If installing soffit panels over existing wood soffits, soffit ‘J’ channel can beused in place of frieze runner.
AluminumSoffit SystemsSOFFIT, 3-Panel, 12” Wide,SOFFIT, 4-Panel, 16” Wide,SolidSolidVented - 2 panelsVented - 1 panelColors: AllSOFFIT 3-PanelColors: AllLength: 12’SOFFIT 4-PanelNo/Ctn: 17CodeStyleNet Free AreaA3SS12A3VS12SolidVented - 1 pnl.StyleA4SS16A4VS1612”3/8”No/Ctn: 12Code—3.24 sq.in.SolidVented - 2 pnl.Frieze RunnerNet Free Area—6.48 sq.in.16”3/8”4”Length: 12’4”Gutter ApronJ Channel1-1/8”2-1/2”106 : FRPColors: AllLength: 12’Code: GAColors: All*No/Ctn: 25Length: 10 ’Code: UTColors: AllNo/Ctn: 25Smooth Brick Mould CoverDouble ChannelLength: 12 ’No/Ctn: 25ADE12 Roof Edge - 1-3/8”3/8”1-1/2”1/8”1/8”1/2”Code: DCColors: AllLength: 10 ’No/Ctn: 5Fascia Trim - SMOOTH FinishCode: BMColors: All*Length: 10’Fascia Trim - RUSTIC FinishCode: ADE12Colors: All Length: 12 ’No/Ctn: 10No/Ctn: 25No/Ctn: 251/8”10”CodeSizeColorsSmooth - HemmedFH4FH6FH8FH104”6”8”10”Rustic - UnhemmedF6-RF8-RNom: .024”4” , 6” , 8” , 10”Nom: .019”6” , �1/8”7/8”*Except Copper PennyHemmed7/8”Unhemmed
(4-way overhang) Soffit & Fascia Installation Tips Hip Roof Do NOT Over Nail Fascia Trim. Recommended: One Nail Every 36 in. Fascia
Install Soffit above gable walls Soffit should start butted to eave facia. Install longer piece first, short piece near peak Soffit ends should always land in middle of ladder rung Soffit should fit tightly to back of fascia -gap against wall is ok Install soffit with 8D ring shank nails using a coil nail air gun Work from one end of soffit .
Installation Instructions for Rollex Aluminum Soffit and Fascia System System 3 12" Aluminum Soffit System Calculation Chart To determine the number of System 3-12 soffit panels required, follow these simple steps: 1. Measure width of soffit from wall to outside of fascia board. 2. Measure length of overhang. 3. Use chart to find the number of .
1 Contents Siding 2 Haven 4 Haven Accessories 8 Woodland 12 Woodland 25' 14 Board & Batten 16 Estate 20 Residential 24 Royal Crest 30 Designer Accessories 38 Traditional Accessories Soffit 52 Designer Soffit 56 Traditional Soffit 60 Builder Soffit 64 Soffit Accessories Shake & Shingles 70 Portsmouth Shake & Shingles Stone 80 Atlas Stone Aluminum .
8-foot soffit. Space and caulk the end and edge joints 3/16 in. when using 16-foot soffit. LP SmartSide Soffit products are not designed for and are not suitable for use as siding or trim other than Smooth Foundations Soffit. For information on fastening LP SmartSide soffits in high wind speed areas, refer to APA Product Report PR-N117.
Fascia! Soffit! Eave and Gutter Ł Prefinished aluminum soffit and fascia and LP Smart and James Hardie products are highly recommended from a maintenance viewpoint! however painted or stained wood (excluding OSB) are also acceptable" Ł SmartSide Trim! SmartSide Soffit! HardiTrim! HardiSoffit Ł Prefinished aluminum eavestroughs and downspouts
LP Smartside Siding LSS48 LP SmartSide Siding 8” On Center Primed Cedar Texture 4’ x 8’ 3/8 . Vinyl Soffit - Stocked at Ephrata Location Aluminum Soffit Vinyl Soffit - Stocked at Newville Location . SOF6W Berger 6 Inch Aluminum Fascia .024 - White 25 12’ .
Aluminum Sheet Aluminum Plate Aluminum Round Bar Aluminum Square Bar Aluminum Flat Bar Aluminum Angle Aluminum Structural Channel Aluminum Safety Grip Channel . peeled or smooth turned. Available in a wide selection of lengths and grades. 316/316LAvailable in pump shaft quality. Size
Aluminum Association's Task Group on Visual Quality Attributes of Aluminum Sheet and Plate. ALUMINUM ASSOCIATION SHEET AND PLATE DIVISION COMPANIES Alcan Inc. Alcoa, Inc. ARCO Aluminum Inc. Coastal Aluminum Rolling Mills, Inc. Corus Aluminium Rolled Products Jupiter Aluminum Corporation Kaiser Aluminum & Chemical Corporation Spectrulite .
