SIMATIC PCS 7 PCS 7 Faceplates - Siemens

SIMATIC PCS 7 SIMATIC PCS 7 PCS 7 faceplates1PCS 7 Faceplates2Block iconsSIMATICPCS 7PCS 7 FaceplatesProgramming and Operating Manual09/2007A5E00807901-02Quality Code and StatusDisplays3

Safety GuidelinesSafety GuidelinesThis manual contains notices you have to observe in order to ensure your personal safety, as well as to preventdamage to property. The notices referring to your personal safety are highlighted in the manual by a safety alertsymbol, notices referring only to property damage have no safety alert symbol. These notices shown below aregraded according to the degree of danger.DANGERindicates that death or severe personal injury will result if proper precautions are not taken.WARNINGindicates that death or severe personal injury may result if proper precautions are not taken.CAUTIONwith a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.CAUTIONwithout a safety alert symbol, indicates that property damage can result if proper precautions are not taken.NOTICEindicates that an unintended result or situation can occur if the corresponding information is not taken intoaccount.If more than one degree of danger is present, the warning notice representing the highest degree of danger willbe used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating toproperty damage.Qualified PersonnelThe device/system may only be set up and used in conjunction with this documentation. Commissioning andoperation of a device/system may only be performed by qualified personnel. Within the context of the safety notesin this documentation qualified persons are defined as persons who are authorized to commission, ground andlabel devices, systems and circuits in accordance with established safety practices and standards.Prescribed UsageNote the following:WARNINGThis device may only be used for the applications described in the catalog or the technical description and onlyin connection with devices or components from other manufacturers which have been approved orrecommended by Siemens. Correct, reliable operation of the product requires proper transport, storage,positioning and assembly as well as careful operation and maintenance.TrademarksAll names identified by are registered trademarks of the Siemens AG. The remaining trademarks in thispublication may be trademarks whose use by third parties for their own purposes could violate the rights of theowner.Disclaimer of LiabilityWe have reviewed the contents of this publication to ensure consistency with the hardware and softwaredescribed. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, theinformation in this publication is reviewed regularly and any necessary corrections are included in subsequenteditions.Siemens AGAutomation and DrivesPostfach 48 4890437 NÜRNBERGGERMANYA5E00807901-02 09/2007Copyright Siemens AG 2007.Technical data subject to change

Table of contents1PCS 7 Faceplates. 71.11.1.11.1.2Faceplates.7General Information on Faceplates .7Overview 101.2.10.11.2.10.2Faceplates: Technological Blocks .11CTRL PID (All Views).13CTRL PID: Standard view .13CTRL PID: Maintenance view .15CTRL PID: Parameter view.17CTRL PID: Limits view .19CTRL S (All Views) .21CTRL S: Standard view.22CTRL S: Maintenance view.24CTRL S: Parameter view .24CTRL S: Limits view.24CTRL S: StandardS View.25DIG MON (All Views) .27DIG MON: Standard view.27DOSE (All Views).28DOSE: Standard view .28DOSE: Maintenance view .30DOSE: Parameter view.31DOSE: Limits view .32ELAP CNT (All Views).33ELAP CNT: Standard view.33FMCS PID (All Views) .35FMCS PID: Standard view .35FMCS PID: Maintenance view .38FMCS PID: Parameter view .40FMCS PID: Limits view .42FMCS PID: StandardS View .43FMT PID (All Views).45FMT PID: Standard view .46FMT PID: Maintenance view .48FMT PID: Parameter view.48FMT PID: Limits view .48FMT PID: StandardS View .49INTERLOK: Standard view .50MEAS MON (All Views).51MEAS MON: Standard view.51MEAS MON: Limits view .53MOT REV (All Views).54MOT REV: Standard view .54MOT REV: Maintenance view .55PCS 7 FaceplatesProgramming and Operating Manual, 09/2007, A5E00807901-023

Table of 2.221.2.22.11.2.22.21.2.231.2.241.2.251.2.26MOT SPED (All Views). 56MOT SPED: Standard view. 56MOT SPED: Maintenance view. 57MOTOR (All Views). 58MOTOR: Standard view . 58MOTOR: Maintenance view . 60OP A: Standard view . 60OP A LIM: Standard view . 61OP A RJC: Standard view . 61OP D: Standard view. 62OP D3: Standard view. 63OP TRIG: Standard view. 64RATIO P (All Views) . 65RATIO P: Standard view . 65RATIO P: Limits view . 67SWIT CNT (All Views) . 68SWIT CNT: Standard view . 68VAL MOT (All Views). 70VAL MOT: Standard view. 70VAL MOT: Maintenance view. 71VALVE (All Views). 72VALVE: Standard view. 72VALVE: Maintenance view. 74Global Views . 74Global View: Batch view. 75Global View: Message View. 76Global View: Trend view . lates: Asset Management . 78Global Representations and Views of Asset Faceplates . 79Maintenance View [Asset]. 83Message View [Asset]. 85Ident View [Asset] . 86Individual Views of the PDM Faceplate [Asset] . 90Individual Views of the IPC Faceplate [Asset] . 93Views of the OB BEGIN Faceplate [Asset] . 95Views of the ASSETMON Faceplate [Asset] . 101Block icons . 1032.1General Properties of Block Icons . 1032.2Position of Faceplates. 1062.3Highlighting the Block Icon for "Loop in Alarm" and "Select Picture via Process Tag". 1072.42.4.12.4.2Block icons: Template pictures . 108@@PCS7Typicals.pdl and @Template.pdl template pictures . 108Display for avoiding stop without asset management. k Icons: Technological Blocks. 111Block Icons: Technological Blocks. 111Block icon: CTRL PID. 112Block icon: CTRL S . 113Block icon: DIG MON . 115Block icon: DOSE. 116Block icon: ELAP CNT . 117Block icon: FMCS PID. 118Block icon: FMT PID. 119PCS 7 FaceplatesProgramming and Operating Manual, 09/2007, A5E00807901-02

Table of ock icon: INTERLOK.119Block icon: MEAS MON .120Block icon: MOT REV .121Block icon: MOT SPED .122Block icon: MOTOR .123Block icon: OP A .124Block icon: OP A LIM .124Block icon: OP A RJC .124Block icon: OP D .125Block icon: OP D3 .125Block icon: OP TRIG .126Block icon: RATIO P .126Block icon: SWIT CNT .127Block icon: VAL MOT .127Block icon: VALVE .1282.62.6.1Block Icons: Asset Management.129Block Icons: Asset Management.129Quality Code and Status Displays . 1333.1The Quality Code Display .1333.2Maintenance Status of MS.1353.3Status Display for Redundant Components [Asset].138Index . 143PCS 7 FaceplatesProgramming and Operating Manual, 09/2007, A5E00807901-025

Table of contents6PCS 7 FaceplatesProgramming and Operating Manual, 09/2007, A5E00807901-02

PCS 7 Faceplates1.1Faceplates1.1.1General Information on Faceplates1What is a Faceplate?The faceplate is the graphical display of all the elements of a technological block in theautomation system or of asset management components that perform operator control andmonitoring functions. The faceplate is displayed in a separate window on the OS and can becalled up by means of picture-selection buttons, the process-tag list or the block icon.Requirements You must use a system, which has WinCC and the "Basis Process Control" and"Advanced Process Control" control system packages. You must use a graphics board with a resolution of 1280x1024 pixels. One screen candisplay up to 12 Faceplates with a size of 320 x 256 pixels in a matrix format consisting of3 rows and 4 columns and without scroll bars. If you use a lower-resolution graphicsboard, you must display the scroll bars or reduce the number of blocks.Advantages of the FaceplatesThe Faceplates have the following advantages: Easy to learn Easy to configure, by means of a defined interface between the faceplate and theAS block Easy to handle, due to only a few handling instructions Clear representation of the process WinCC and Windows conformityPCS 7 FaceplatesProgramming and Operating Manual, 09/2007, A5E00807901-027

PCS 2H7 Faceplates1.1 FaceplatesDisplayThe Faceplates have two different display formats: Group display: Visualization of AS values in different views, with element for selecting theloop display Loop display: Visualization of the elements of all views of the group displayAdditional informationYou will find more information about designing, configuring and testing a faceplate in thePCS 7 Programming Guide for Blocks Manual.NoteThe Faceplates shown here in the documentation may differ slightly from those that areconfigured in WinCC.8PCS 7 FaceplatesProgramming and Operating Manual, 09/2007, A5E00807901-02

PCS 2H7 Faceplates1.1 Faceplates1.1.2Overview objectsToolbar IconsEach faceplate has a toolbar containing the following icons:Pinning the faceplateIn the left-hand corner above the overview row, there is an icon that can be used to "pin" afaceplate so that it remains during an area change. The key appears as follows: Not pinned(once the faceplate has been called) Pinned(once the button has been pressed)The faceplate remains pinned until it is closed again. Pressing the key again has no effect.Group displayThe group display [1] shows the information that is transferred from ALARM 8P of the blockinstance to WinCC. The group display is linked to the "EventState" of the variable.Lock/Unlock MessagesThe "Lock/unlock messages" function is implemented in the overview with a key [2].The group displays shows whether all the messages of a block instance are locked orunlocked. If a white * character [1a] appears in all 4 of the group-display fields, all messagesare locked.The button is only visible to operators assigned the permission level defined in the blocksymbol property "Processcontrolling backup".PCS 7 FaceplatesProgramming and Operating Manual, 09/2007, A5E00807901-029

PCS 2H7 Faceplates1.1 FaceplatesAcknowledge messagesWith key [3], all messages of the block instance can be acknowledged.The button is only visible to operators assigned the permission level defined in the blocksymbol property "Processcontrolling backup".Suppress MessagesMessage suppression indicates whether the "Suppress process messages" function in theAS block is deactivated [4] or activated [4a] using the "MSG LOCK" parameter. If messagesuppression is activated, all messages in this block instance are suppressed – except forprocess control messages.Occupied DisplayThe occupied display [5] indicates whether the SIMATIC BATCH block instance is occupied("OCCUPIED" parameter). Additional information is then displayed in the batch view.10PCS 7 FaceplatesProgramming and Operating Manual, 09/2007, A5E00807901-02

PCS 2H7 Faceplates1.2 Faceplates : Technological Blocks1.2Faceplates: Technological BlocksTechnological BlocksCTRL PID (All Views) (Page 13)CTRL PID: Standard view (Page 13)CTRL PID: Maintenance view (Page 15)CTRL PID: Parameter view (Page 17)CTRL PID: Limits view (Page 19)CTRL S (All Views) (Page 21)CTRL S: Standard view (Page 22)CTRL S: Maintenance view (Page 24)CTRL S: Parameter view (Page 24)CTRL S: Limits view (Page 24)CTRL S: StandardS view (Page 25)DIG MON (All Views) (Page 27)DIG MON: Standard view (Page 27)DOSE (All Views) (Page 28)DOSE: Standard view (Page 28)DOSE: Maintenance view (Page 30)DOSE: Parameter view (Page 31)DOSE: Limits view (Page 32)ELAP CNT (All Views) (Page 33)ELAP CNT: Standard view (Page 33)FMCS PID (All Views) (Page 35)FMCS PID: Standard view (Page 35)FMCS PID: Maintenance view (Page 38)FMCS PID: Parameter view (Page 40)FMCS PID: Limits view (Page 42)FMCS PID: StandardS view (Page 43)FMT PID (All Views) (Page 45)FMT PID: Standard view (Page 46)FMT PID: Maintenance view (Page 48)FMT PID: Parameter view (Page 48)FMT PID: Limits view (Page 48)FMT PID: StandardS view (Page 49)INTERLOK: Standard view (Page 50)PCS 7 FaceplatesProgramming and Operating Manual, 09/2007, A5E00807901-0211