Lithium-Ion Battery Charger
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 1 Friday, October 28, 2005 2:54 PMLithium-Ion Battery ChargerChargeur de batterie ion-lithiumCargador de baterías de LitionDX-DA100501/DX-DA100502U S E R G U I D E G U I D E D E L’ U T I L I S AT E U R G U Í A D E L U S UA R I O
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 2 Friday, October 28, 2005 2:54 PM2Dynex DX-DA100501/502 battery chargerDynex DX-DA100501/502 batterychargerIntroductionCongratulations on your purchase of the Dynex Model DX-DA100501/502lithium-ion camcorder and digital camera battery quick charger. With theincluded AC adapter (for use with a standard power outlet) or the 12 V car cord,you can quickly charge your digital camera and camcorder batteries at home or inthe car.ContentsIntroduction.2Important safety instructions .2Features .3Product components.4Setting up the charger .5Using the tions.14Warranty.14Legal notices.14Français . 15Español . 29Important safety instructionsSafety precautionsDo not use this charger inside a drawer, closed cabinet, or covered with a cloth.The heat from charging may damage the charger or the battery pack. This chargerbecomes slightly warm during use.Do not attempt to open the charger. Doing so voids your warranty.
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 3 Friday, October 28, 2005 2:54 PM3FeaturesDo not allow moisture of any kind to come in contact with the charger. Neverimmerse in water for any reason.Do not store in areas which may expose the charger to extreme temperatures.Avoid placing in direct sunlight, such as on a car dashboard. High temperatureswill warp or melt plastics.Do not drop the charger. A severe jolt may cause permanent damage and is notcovered by the warranty.Follow this User Guide carefully. Follow the correct procedures when setting up thebattery charger.Warning: For use with Lithium-Ion (Li-ion) batteries only. Do not attempt tocharge Nickel Cadmium (Ni-Cd) or Nickel Metal Hydride (Ni-MH) batteries withthis charger.Features Compatible with most 3.6 V and 7.2 V Camcorder/Digital CameraLithium-Ion (Li-ion) batteries Precision end-of-charge voltage detection guarantees full charging ofbattery packs Top-off function trickle charges to maintain a full charge Automatic battery voltage detection with LED indication LED status indicator displays charger mode Abnormal battery detection identifies faulty battery and halts charging Overcharge protection Timer protection
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 4 Friday, October 28, 2005 2:54 PM4Product componentsProduct componentsBattery chargerMain charging bay(with Sony-typebattery contacts)Power input jack (on theback of the charger)Charging status indicator3.6 V/7.2 V battery voltage indicatorPower indicatorBattery/adapter plate latchAdapter plate AAdapter plate BAdapter plate CAdapter plate D Universal plate E
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 5 Friday, October 28, 2005 2:54 PM5Detachable deskstand12V DC adapterAC adapterSetting up the chargerA detachable desktop stand is included with your battery charger. This allows youto use your charger in a tilted position or a vertical (upright) position.To operate the charger in a horizontal position: Remove the desktop stand from the base of the charger by carefullypressing on the bottom of the desktop stand and lifting it away from thecharger.To operate the charger in a tilted position:1 Insert the tab at the pointed end of the desktop stand into the mountinghole on the back of the charger (marked with a).
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 6 Friday, October 28, 2005 2:54 PM6Using the charger2 Carefully press the two latches at the bottom of the desktop stand into thebase of the charger.To operate the charger in the vertical position:1 Insert the tab at the pointed end of the desktop stand into the mountinghole (marked with a) on the back of the charger.2 Carefully press the two latches at the bottom of the desktop stand into thebase of the charger.Using the chargerConnecting your charger to a power sourceTo use with an standard AC power outlet:1 Connect the AC adapter to the power input jack on the back of your charger.
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 7 Friday, October 28, 2005 2:54 PMUsing the charger2 Plug the AC adapter into any standard power outlet. The red powerindicator turns on.To use with a 12 V DC (car) power connector:1 Connect the 12 V DC car cord barrel plug to the power input jack.2 Insert the 12 V DC car cord cigarette lighter plug into the cigarette lightersocket of the vehicle. The red power indicator turns on.7
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 8 Friday, October 28, 2005 2:54 PM8Using the chargerMounting the battery into the chargerWarning: For use with Lithium-Ion (Li-ion) batteries only. Do not attempt tocharge Nickel Cadmium (Ni-Cd) or Nickel Metal Hydride (Ni-MH) batteries.To mount the battery into the charger:1 Note where the guides and contacts are located on the battery and alignthem with the corresponding guides and contacts on the charger, then slidethe battery into place in the charging bay.2 Press the battery down, then slide it up (away from the indicator lights).- OR Slide the battery up, then press it down (depending on the battery to becharged).Do not force the battery onto the charger. If it does not slide easily into theguides, re-align it and try again.USING AN ADAPTER TRAYDepending on your battery type, you may need to use an adapter tray. Refer to theBattery Compatibility List to determine which adapter tray should be used withyour battery type.To install the adapter tray onto the charger:1 Slide the central notch on the adapter tray’s upper edge into the slot on theupper edge of the charger bay, then carefully press down on the lower edgeof the adapter tray.The adapter tray snaps firmly in place. Install the battery so that its contactsmeet the contacts on the adapter tray.2 To remove the adapter tray, pull back on the battery/adapter latch, then liftthe adapter tray up and out of the charger.USING THE UNIVERSAL ADAPTER PLATEThe universal adapter plate label provides only a partial list of batteries that arecompatible with this charger plate. Refer to the Battery Compatibility List for theentire make and model list of compatible batteries.
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 9 Friday, October 28, 2005 2:54 PM9Using the chargerNote: When inserting your battery for charging, you may need to apply pressureand pull down to open the spring-loaded slide tray.BATTERY POSITIONING GUIDEBatteriesCANON: NB-5HJVC: BN-306, BN-V312UKODAK: KLIC-7000KYOCERA: BP-780SMINOLTA: NP-200, NP-400NIKON: EN-EL1, EN-EL3OLYMPUS: PS-BLM1OPTEX: LI12, LI13, LI14, LI29, LI61, LI62PANASONIC: CGA-S101A, CGA-S101BRADIO SHACK: 23-604, 23-618, 23-619,23-622, 23-625, 23-627SANYO: DB-L20, UR-421SONY: NP-FT1, NP-FR1Position
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 10 Friday, October 28, 2005 2:54 PM10Using the chargerBatteriesPositionFor the batteries in the box below, you need to flip up the Flip 2 mating battery contactterminals found on the right side of charger plate.OPTEX: LI27, LI41PANASONIC: CGA-DU07, DU14, DU21,S001E, S002,CGR-602A, 602E,D110, D120, D220, D320,DMW-BCA7, BM7, BL14,VW-VBD07, VBD14RADIO SHACK: 23-382NIKON: EN-EL2OPTEX: LI16RADIO SHACK: 23-621KONICA: DR-LB1KYOCERA: BP-800S, BP-1000SOPTEX: LI15POLAROID: PR111DG, PR110DGRADIO SHACK: 23-617SHARP: AD-S30BT, AD-S31BT, AD-T50BT,AD-T51BTTOSHIBA: PDR-BT1, PDR-BT9
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 11 Friday, October 28, 2005 2:54 PM11Using the chargerBatteriesCANON: NB-1L, NB-1LH, NB-2L, NB-2LH,NB-3L, NB2F12, BP-2L12/14,BP-3LCLCASIO: NP-20, NP-30, NP-40FUJI: NP-40, NP-60, NP-80, NP-120KODAK: KLIC 5000, KLIC 5001MINOLTA: DR-LB1, DR-LB4, NP600NIKON: EN-EL5OLYMPUS: LI-10B, LI-12B, LI-10, LI-20BOPTEX: LI10, LI11, LI12, LI17, LI19, LI23,LI26, LI30, LI38PANASONIC: CGR-S101A, CGA-S301,CGA-S302A, VW-VBA05,CGA-003A/1B, DMV-BC7,VM-VBA10PENTAX: D-L12, D-L17, D-L18RADIO SHACK: 23-602, 23-605, 23-606,23-608, 23-609, 23-611,23-612, 23-613, 23-615,23-616, 23-620, 23-624RICOH: DB-43, DB-40SANYO: DB-L10TOSHIBA: PDR-BT2, PR-BT3FUJI: NP80, NP100JVC: BN-V101KODAK: KLIC-3000OPTEX: LI15PANASONIC: VW-VBP10POLAROID: PR105DGRICOH: DB-30SANYO: UR-211SONY: LIP-10Position
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 12 Friday, October 28, 2005 2:54 PM12Using the chargerBatteriesPositionFor the batteries in the box below, you need to flip up the Flip 1 mating battery contactterminals found on the left side of charger plate.SHARP: BT-L226OPTEX: LI28Charging the batteryCharging begins as soon as the battery is properly connected. The green chargingstatus indicator blinks as the battery is being charged. When the battery is fullycharged, the green charging status indicator stops blinking and stays on. You canremove the battery for use when this happens, but we recommended that youleave the battery on the charger for another 30 minutes to ensure a full (toppedoff) charge.AUTOMATIC BATTERY VOLTAGE DETECTION AND INDICATIONMost camcorder and digital camera Lithium-Ion (Li-Ion) batteries are either 3.6 Vor 7.2 V. This charger has built-in battery detection for automatic selection of theappropriate output voltage to the battery, to ensure safe and efficient charging.The 3.6 V/7.2 V battery voltage indicator lights red when charging a 3.6 V battery,and lights green if the battery is 7.2 V.
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 13 Friday, October 28, 2005 2:54 PM13TroubleshootingABNORMAL BATTERY DETECTIONYour charger detects an abnormal battery pack by sensing the voltage. If it is toohigh or too low, or if the battery pack does not reach full charge status within 8hours of charging, the charger stops the operation immediately and indicate theabnormal condition by flashing both the power and battery status indicator LEDs.Normal operation resumes when the faulty battery is removed.TroubleshootingProblemPossible causes and solutionsNo indicator lights Confirm that the AC Adapter is firmly connected atboth ends (wall and power input jack) Confirm that the power outlet is functioning normally Confirm that the car cord is firmly connected at bothends (cigarette lighter socket and power input jack) Confirm that the cigarette lighter socket isfunctioning normallyPower light only The battery is fully charged * The battery is mounted incorrectly, remove andremount the battery Clean the battery and charger contacts The battery may be defective*Power and battery status LEDs both blinking Defective battery*Hissing noise while chargingNormal operation due to advance switchingcircuitry* To determine if the battery is overcharged or defective, place it on the camcorderor digital camera and turn it on. If the camcorder or digital camera does not turnon, the battery is probably defective. If the camcorder or digital camera does notoperate, leave the power turned on for 30 minutes, then remove the battery andput it on the charger. The charger should go into charge mode, indicated by thegreen blinking charge status indicator.MaintenanceIf the charger must be cleaned, make sure it is unplugged, and then wipe the bodyof the charger with a clean cloth lightly dampened with mild detergent. To cleanthe metal contacts, use a clean cloth lightly dampened with rubbing alcohol.
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 14 Friday, October 28, 2005 2:54 PM14SpecificationsSpecificationsInput:Stand-by current:Charging current:Charge termination:12 V DC30 mA800 mA max @ constant current modeFixed voltage(4.2 V for 3.6 V battery, 8.4 V for 7.2 V battery)WarrantyLimited 1 Year WarrantyDynex warrants that for 1 year from date of purchase as stated on your receipt, itwill replace this product if found to be defective in materials or workmanship. Ifdefective, return the item to the store where it was purchased before theexpiration of the 1 year warranty period, with your original receipt, and we willreplace it with a then-current equivalent Dynex product (or a pro-rated refund atDynex's option). This warranty is available only for the original purchaser of thisproduct. Dynex will not be responsible for any incidental or consequentialdamages or for any loss arising in connection with the use or inability to use thisproduct. Some states and provinces do not allow the exclusion or limitation ofincidental or consequential damages, so the above limitation or exclusion may notapply to you. For defective products purchased online, please contact:www.dynexproducts.comDynex support service at 1-800-305-2204. Dynex, Richfield, MinnesotaLegal notices 2005 Dynex. DYNEX and the DYNEX logo are trademarks of Best Buy EnterpriseServices, Inc. Other brands and product names are trademarks or registeredtrademarks of their respective holders. Specifications and features are subject tochange without notice or obligation.Support number: (800) 305-2204URL: www.dynexproducts.com
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 15 Friday, October 28, 2005 2:54 PMChargeur de batterie DX-DA100501/502 de Dynex15Chargeur de batterie DX-DA100501/502de DynexIntroductionFélicitations d’avoir acheté ce chargeur rapide de batterie ion-lithium pourappareil photo numérique et caméscope, modèle DX-DA100501/502 de Dynex.Avec l’adaptateur CA inclus (pour utilisation sur une prise secteur standard) ou lecâble pour voiture de 12 V, il est possible de charger rapidement les batteries d’unappareil photo ou d’un caméscope chez soi ou dans la voiture.Table des matièresIntroduction.15Instructions de sécurité importantes.15Caractéristiques .16Description du produit .17Configuration du chargeur .18Fonctionnement du chargeur.19Problèmes et solutions.26Entretien.27Caractéristiques .27Garantie.27Avis juridiques.28Español . 29Instructions de sécurité importantesMesures de sécuritéNe pas utiliser ce chargeur dans un tiroir, une armoire fermée ou couvert par untissu. La chaleur dissipée pendant la charge peut endommager le chargeur ou lebloc-batterie. Ce chargeur chauffe légèrement pendant son utilisation.Ne pas tenter d’ouvrir le chargeur. Cela annulerait la garantie.Ne pas exposer le chargeur à une quelconque humidité. Ne jamais l’immergerdans l’eau.
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 16 Friday, October 28, 2005 2:54 PM16CaractéristiquesNe pas entreposer le chargeur dans des zones où il serait exposé à destempératures élevées. Éviter de l’exposer à la lumière directe du soleil, parexemple ne pas le mettre sur le tableau de bord d’un véhicule. Des températuresélevées déformeront ou feront fondre le plastique.Ne pas faire tomber le chargeur. Une secousse importante peut causer desdommages permanents non couverts par la garantie.Se référer à ce Guide de l’utilisateur avec attention. Observer les procéduresrecommandées pour l’installation du chargeur de batterie.Avertissement : Ne doit être utilisé que pour des batteries ion-lithium. Ne pasessayer de charger des batteries au nickel-cadmium (Ni-Cd) ou à hydruremétallique de nickel (NiMh) avec ce chargeur.Caractéristiques Compatible avec la majorité des batteries ion-lithium de 3,6 V et 7,2 V pourappareil photo ou caméscope Un dispositif de détection de la tension détermine avec précision le niveaude charge, garantissant la pleine charge des bloc-batteries La fonctionnalitécomplément de charge et charge d’entretien permet demaintenir la charge totale en permanence Détection automatique de tension avec DEL témoin La DEL témoin indique le mode du chargeur Dispositif de détection d’anomalie de la batterie pour arrêter la charge Protection contre les surcharges Temporisation de protection
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 17 Friday, October 28, 2005 2:54 PM17Description du produitDescription du produitChargeur de batterieLogement de charge principal(avec bornes pour batteries detype Sony)Prise d’entrée d’alimentation (àl’arrière du chargeur)Témoin d’état de chargeTémoin de tension de la batterie 3,6 V/7,2 VTémoin de mise sous tensionPatte de verrouillage de l’adaptateur pour batterieAdaptateur AAdaptateur BAdaptateur CAdaptateur D Adaptateur universel E
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 18 Friday, October 28, 2005 2:54 PM18Support de bureauamovibleAdaptateur 12 V CCAdaptateur CAConfiguration du chargeurUn support de bureau amovible est inclus avec le chargeur de batterie. Il permetd’utiliser le chargeur en position inclinée ou verticale.Pour utiliser le chargeur en position horizontale : Enlever le support de bureau de la base du chargeur en appuyantdélicatement sur le dessous du support pour le détacher du chargeur.Pour utiliser le chargeur en position inclinée :1 Insérer l’ergot de la pointe du support de bureau dans le trou de montage àl’arrière du chargeur (identifié par le symbole).
Dynex DX-DA100501 camcorder battery charger - combined.fm Page 19 Friday, October 28, 2005 2:54 PMFonctionnement du chargeur192 Insérer délicatement sur les deux pattes de verrouillage situées sous lesupport de bureau dans la base du chargeur.Pour utiliser le chargeur en position verticale :1 Insérer l’ergot de la pointe du support de bureau dans le trou de montage àl’arrière du chargeur (identifié par le symbole).2 Insérer délicatement sur les deux pattes de verrouillage situées sous lesupport de bureau dans la base du chargeur.Fonctionnement du chargeurConnexion du chargeur à une source d’alimentationPour l’utiliser avec une prise secteur CA standard :1 Connecter l’adaptateur CA à la pris
Most camcorder and digital camera Lithium-Ion (Li-Ion) batteries are either 3.6 V or 7.2 V. This charger has built-in batter y detection for automatic selection of the appropriate output voltage to the battery, to ensure safe and efficient charging. The 3.6 V/7.2 V battery voltage indicator li ghts red when charging a 3.6 V battery,
14-100508-000 Assy. Lithium Battery, 30 Ahr 14-100508-900 Assy. Lithium Battery, preown 30 Ahr 14-100957-002 Assy. Lithium Battery, w/ jumper 48 Ahr 14-100957-004 Assy. Lithium Battery, w/ jumper 30 Ahr 14-100957-904 Assy. Lithium Battery, preown 30 Ahr 14-860202-002 Pkg. Envoy, Lithium, with ACDC 115V 14-860202-004 Pkg. Envoy w/ Lithium .
1. Are all lithium-ion batteries created equal? — NO 2. Are all chemistries the same? — NO 3. Are all batteries using the same lithium-ion chemistry the same? — NO 4. Do all lithium-ion batteries have similar cycle life, like Flooded Lead Acid (FLA)? — NO 5. Can I use any lithium-ion battery in my equipment? — NO 6.
BATTERY ACID. 4.1 Locate the charger as far away from the battery as the DC cables permit. 4.2 Never place the charger directly above the battery being charged; gases from the battery will corrode and damage the charger. 4.3 Do not set the battery on top of the charger. 4.4 Never allow battery ac
The LIFEPAK 15 Monitor/Defibrillator Station Lith ium-ion (Li-ion) Battery Charger and Mobile Li-ion Battery Charger are intended for use only with LIFEPAK 15 Li-ion rechargeable batteries. IMPORTANT! No other batteries are compatible with these chargers. To avoid confusion between batteries for the LIFEPAK
Insert the battery into the charger. This is a diagnostic charger. The charger LED lights current battery status. They are as follows: Charging Fully Charged Over Temperature Charging Fault 1 If the battery is inserted into the charger when warm or hot, the charging LED indicator light on the
Electrical - Battery Tray and Charger Electrical - Battery Tray and Charger 1 YL 524148828 Battery Tray 2 YL 580029671 Thru 9/2002 Battery Charger, 24V, 120vac, Micro Control YL 580034920 10/2002 thru 4/2005 Battery Charger, 24V, 120vac, Micro Control YL 580055473 4/2005 thru 11/2007 Battery Charger, 24V, 120vac, Micro Control
Locate charger as far away from battery as DC cables permit. 2. Never place charger directly above battery being charged. Gases from battery will corrode and damage charger. 3. Never allow battery acid to drip on charger when reading gravity or filling battery. 4. Do not operate charger
The blue light protocol is subject to CTR Policy exemplar standard 11 as follows “CTRs and any related recording or disclosure of personal information will be with the express consent of the individual (or when appropriate someone with parental responsibility for them), or if they lack capacity, assessed to be in their best interests applying the Mental Capacity Act 2005 and its Code of .
