Axeda Enterprise Server Configuration Properties
Axeda Platform - System Configuration properties (Platformsettings)This table lists and describes the properties shown in the Axeda Administration application.These properties are defined and specified in the Platform by the Platform admistrator. (Theproperty, Custom Build Info, is also set in the Platform but is derived from another propertyfile.)To help you find a description of a property quickly, the table lists the properties in alphabeticalorder.Note: Some Platform properties are disabled (commented out) by default and therefore do notappear in the Administration application, System Configuration pages. If they aren’t shown inthis online help then they are set to not show by default in the Platform.If you have any questions or concerns about how your server is configured with regard to itsproperty settings, contact your Platform administrator.System Configuration PropertiesPropertyAccess message timeoutDescriptionThe number of seconds the Access application waits between messages from AccessViewer or Access Remote. If the Access application does not receive any messageswithin this time period (for example, if there are network problems), the session isdisconnected. The default is 40 seconds.In addition, this is the period of time within which the Access Viewer and AccessRemote operators must connect to the shared session. If both Access Viewer andRemote do not connect to the session within this timeout period, the session will timeout, and a new session must be requested.Access session ID lengthLength (in characters) of the Access Session ID. The default length is 6 characters.Access session timeoutThe number of minutes an inactive session stays open, waiting for activity, before it isremoved. An inactive session is one that has not been used (no Access Viewer orRemote computers shared using this session ID). The default is 10 minutes (betweencontacts).Access unattended sessiontimeoutThe number of minutes an inactive, unattended session stays open, waiting for activity,before it is removed. An inactive session is one that has not been used (no AccessViewer or Remote computers shared using this session ID). The default is 10 minutes(between contacts).ActiveMQ Broker nameThe name of the machine where the ActiveMQ Server (Broker) is running.Additional Auditor typesactively running in thesystemRegisters the types of auditors to use along with the JDBC Auditor when dispatchingaudit messages. Supported values of this property are as follows:AUDITOR SYSLOG SERVER (Note: Configuration properties for the syslog serversuch as host and port number, syslog facility id, and message format template can bespecified in the log4j.appender.SYSLOG definition of the log4j.properties file.]Administrator e-mailThe e-mail address of a user defined as a ServiceLink administrator.Allow automatic creation ofdevicesTrue to allow automatic addition of assets to the database upon registration.1Copyright 2000-2012 Axeda Corporation. All rights reserved. Confidential property.
System Configuration Properties (continued.)PropertyDescriptionAllow automatic creation ofmodelsTrue to allow automatic addition of models to the database upon registration.Allow hosted sessions to bestopped. (Caution should betaken when setting to true.)True to allow the Administrator to stop Global Access Server remote sessions hostedby this server (using the Administration application). By default, the administratorcannot stop host GAS remote sessions (False).Allow remote sessions to bestoppedTrue (the default value to allow the Administrator to stop Global Access Server remotesessions (using the Administration application). If changed to false, administratorcannot stop GAS remote sessions.Allow Remove of TenantuserTrue (default) to enable users to remove Delegated Admin Units from the server. Falseto prevent Applications users from deleting Delegated Admin Units.Users also need the privilege, Delegated Admin Unit - Remove, to be able to removeDelegated Admin Units.Allow the Admin to removeRemote Session AuditInformationSpecifies whether or not the Administrator can remove Audit Session information:Allow unencrypteddevice dataTrue to allow the application to accept unencrypted messages from assets, or false toreject unencrypted messages.Allow users to removepartner accountsTrue to enable users to remove partners defined in the server from the server. False(default) to prevent Applications users from deleting partners. False (default) to prevent the Admin from removing the Audit Session information True to allow the Admin to remove the Audit Session information.Users also need the privilege, Partner Login - Remove Partner Account, to be able toremove Partner Login accounts.Allow users to removeremote Enterprise serversTrue (the default value) to allow the Administrator to delete remote Enterprise servers(from the Administration application). If changed to false, the administrator cannotdelete the remote Enterprise server.AMQ JMX DomainIdentifies the ActiveMQ JMX domain that all objects names will use.Application Bridge Serveruse SSLTrue to enable SSL for the Application Bridge Server (ABS); false (default) to disableSSL for it.Application Bridge Serverweb serviceTrue to enable Web Services for the Application Bridge Server (ABS); false (default) todisable Web Services for it.AQL query SLA target msThe AQL SLA target. Need a little time for Groovy, WS, and network.AQL SLA violation collectionclear sizeSize at which collection recording SLA violations clears to avoid excessive memoryAQL stats logging querycount moduloAQL stats logging query count moduloARemote minimum ping rateMinimum ping rate for an Axeda Access Remote host. By default, this feature is off(property value is -1).2Copyright 2000-2012 Axeda Corporation. All rights reserved. Confidential property.
System Configuration Properties (continued.)PropertyAudit Categories allowed forauditing (no value means allAudit Categories areallowed)DescriptionRegisters the types of audit categories that will be dispatched to the auditors; auditmessages of any other audit category type will not be dispatched. If the value of thisproperty is empty, or if the property is omitted altogether, no filtering will be performed,Audit messages of any audit category type will be dispatched.Note: Currently, audit category filtering is activated for the Syslog Server auditor only.Supported values of this property are as follows: dashboard data-export data-management device-communication file-upload maintenance network notification partner-access report scm-file-transfer scm-package-management transport-servicelink update-windowAuthenticator typesassigned to the partner userstore (comma-separated)Supported Authenticator types for the Partner Login user store (if applicable to thisserver): ActiveDirectoryAuthenticatorMBean IPlanetAuthenticatorMBean LDAPAuthenticatorMBean NovellAuthenticatorMBean OpenLDAPAuthenticatorMBeanAuthenticator typesassigned to the user store(comma-separated)Supported Authenticator types for the Delegated Administration user store (ifapplicable to this server): IPlanetAuthenticatorMBean LDAPAuthenticatorMBean NovellAuthenticatorMBean OpenLDAPAuthenticatorMBeanAuto Refresh RateThe default rate of refreshing tables is every 60 seconds.AxedaDirect SSLconnection port socketThe number of the SSL port that Remote Server can use to connect directly to theEnterprise Server. Defaults to 17002.AxedaDirect standardconnection port socketThe number of the port that Remote Server can use to connect directly to theEnterprise Server. Defaults to 17001.Backup Agent modelnumberName to identify the Backup Agent. Defaults to Backup if not specified. (Applies toAxeda Agents only, not to IDM Agents.)Backup agent serial numberseparatorThe character that separates the model number and serial number in the backup agentserial number. The default is @@.Bad or Uncertain or Emptydata item display valueThe value that the system will display when the actual value for a data value isuncertain, bad, or empty data value. By default, the system displays a question mark,“?”, for data of this type.3Copyright 2000-2012 Axeda Corporation. All rights reserved. Confidential property.
System Configuration Properties (continued.)PropertyDescriptionBind address for AWP filetransfer TCP listenerSpecifies where the AWP endpoint listens for file transfer data from AWP devices.Bind address for AWPmessaging TCP listenerSpecifies where the AWP endpoint listens for incoming messages from AWP devices.Bind address for ASMP/AWP file transferTCPlistenerSpecifies where the ASMP/AWP endpoint listens for incoming file transfer messagesfrom ASMP/AWP devices. This address is the one that the listener actually binds to.Bind address for ASMP/AWP messaging TCPlistenerSpecifies where the ASMP/AWP endpoint listens for incoming messages from ASMP/AWP devices.Bind address for EnforaUDP listenerSpecifies where the Enfora endpoint listens for incoming messages from Enforadevices. Identifies which which network interfaces are listened on if a host should havemore than one Network interface card (NIC). The value 0.0.0.0, or no value at all,specifies all available network interfaces.Build NumberThe version, and number, date and time of this ServiceLink build, which is set duringthe installation. Unless instructed to do so (for example, during an upgrade to a ServicePack), you do not need to modify this setting.You will need it when contacting TechnicalSupport to help identify the version of software you are running.Cache expiration frequency(seconds)The number of seconds that the expiry invalidator waits between runs of its invalidator.Case Number PrefixA prefix for the system to use when creating Case Numbers.Case Number SuffixA suffix for the system to use when creating Case Numbers.Configuration for hostingpreparation folder pathThe path to the user branding folder on the Axeda Enterprise server. The path shouldpoint to the “public” domain. For ublic.folder.path .war/styles/Configuration for specifyingthe ‘from address’ for EmailTransportThe “from” address when sending an e-mail message (M2M).Custom Build InformationDerived from the CustomConfigInfo.properties file (if it exists), displays informationabout the custom configuration.Identifies which network interfaces are listened on if a host should have more than oneNetwork interface card (NIC). The value 0.0.0.0, or no value at all, specifies allavailable network interfaces.Identifies which which network interfaces are listened on if a host should have morethan one Network interface card (NIC). The value 0.0.0.0, or no value at all, specifies allavailable network interfaces.Identifies which network interfaces are listened on if a host should have more than oneNetwork interface card (NIC). The value 0.0.0.0, or no value at all, specifies allavailable network interfaces.Identifies which which network interfaces are listened on if a host should have morethan one Network interface card (NIC). The value 0.0.0.0, or no value at all, specifies allavailable network interfaces.4Copyright 2000-2012 Axeda Corporation. All rights reserved. Confidential property.
System Configuration Properties (continued.)PropertyData source nameDescriptionAxeda offers a stand-alone program called Adapter to gather the data andcommunicate with the Enterprise server through a TCP socket. The port and hostproperties tell the Enterprise system on which host and port the Adapter process islistening.For the port, type the number on which to access the remote data source.For the host, ONLY IF the remote data source is running on a separate node, uncomment the line and type the IP address of the node where the remote data source isrunning.Database Product NameShows the database product configured for the system as “Oracle”.Date formatA date format for the system to use, using Java date format strings. By default the dataexport uses the date format specified by the user’s locale. If the user has not specifieda locale, the server’s default locale is used.For details on date format strings, refer to the JavaDoc forjava.text.SimpleDateFormatDays before alarms areacknowledgedThe number of days after which all alarms will be acknowledged automatically. Anumber less than 1 (the default, -1) indicates that alarms are not to be acknowledgedautomatically.Days to persist statuses indatabaseThe number of days that the server should maintain asset command statuses in thedatabase. Statuses older than this number of days will be deleted automatically fromthe database. The default number of days is 3.Default Agent versionThe version of the Axeda Agent to display in the Asset dashboard of the ApplicationsUI. If the agent version value is not available in the Enterprise system, the serverdisplays the agent version defined in this property. By default, the value is blank .In addition to being informational, this property also guides some server processes.This value is set based on the type of agents with which the server will communicate: Firewall-Friendly agents - The set value is applied as the default version; forexample, 6.5. Wireless agents - This property should be left blank. Both agent types - If the property is left blank, the system will work to distinguish thetype of agents posting data.Important! If this property is left blank, the server will apply the version “M2M” to anyagent that does not supply a version.Default Audit filtering daterange daysThe number of days that the Audit filtering date range filters default to when the daterange is not specified for a search. The default is 7 days.Default chartThe chart that you want to display as the default chart for data. Other settings include: Default Live Chart Default History Comparison Chart Default Bar Comparison ChartDefault e-mail encodingType of encoding to use as the default for e-mail messages. The default is UTF-8.Other possibilities include ASCII, UTF-16, ISO8859, and so on. A complete list isavailable in the Preferences page of the Axeda Applications. The type of encoding youselect must be supported by your e-mail server and client applications.5Copyright 2000-2012 Axeda Corporation. All rights reserved. Confidential property.
System Configuration Properties (continued.)PropertyDescriptionDefault gateway locationand OrganizationinheritanceDefines the behavior for location and organization inheritance by managed devices of aGateway. If true, the inheritance will be enabled by default, meaning Configurationapplication users will be able to select (via the “Set this organization and location for allmanaged devices” check box) that the managed devices of a Gateway inherit thelocation and organization of that Gateway upon registration. If false, the check box isdisabled, preventing a Configuration application user from selecting it to enableinheritance for Gateways. By default this value is set to true.Default missing deviceadditional factorThe number of seconds to use in the equation for determining that assets are missing.The default is 10 seconds.Default missing device pingmultiplierAn integer to use in the equation that determines when the system should consider thatassets are missing. The following equation is used to make this decision:missing current-time last-contact ping-rate * ping-multiplier additional factorDefault partner login sessionduration in minutesThe duration for this session, which is the number of minutes from when the session iscreated until it expires. During this period, no one else may log in to the server usingthe code created for this session. The default is 2880 minutes, or 48 hours (2 days).Desktop Viewer downloadlocation on Linux clientLocation on a Linux client where Quick Launch will download and run the version ofDesktop Viewer required for a remote session with the Desktop Server running on aremote asset. By default, /opt/Axeda/Desktop/Viewers.Desktop Viewer downloadlocation on Windows clientLocation on a Windows client where Quick Launch will download and run the versionof Desktop Viewer required for a remote session with the Desktop Server running on aremote asset. By default, c:\Program Files\Axeda\Desktop\Viewers.Devcon cachesynchronization delayNumber of seconds between synchronizations of the asset context cache with thedatabase.Device communicationmaintenance enable flagIf true, enables the maintenance ping manager; if false, disables the maintenance pingmanager.Device communicationmaintenance ping agent urlThe URL where you want the agents to send their maintenance pings (when theEnterprise Server has placed them in maintenance mode).Device communicationmaintenance ping delayThe number of minutes to wait between maintenance pings.Device communicationmaintenance ping ownerThe JNDI name of the data source as configured on the Enterprise Server to whichagent maintenance pings are being redirected.Device communicationmaintenance ping rateThe number of seconds to wait between sending maintenance pings (from the agent tothe Enterprise Server).Device communicationmaintenance ping re-directServiceLink urlThe URL of the Enterprise Server to which the agent maintenance pings are beingredirected.Device communicationnotification display sourceif true, notifications sent to the server administrator will identify the source of the errors(for example, an XML posting from a specific agent); if false (or blank), notifications willnot show the source of the error. Default is true.Device communicationnotification interval inminutesThe number of minutes to wait before sending an e-mail message to the serveradministrator. Leaving the parameter blank or specifying a negative number disablesthe property completely. The e-mail address used is that defined incom.axeda.drm.administrator.email6Copyright 2000-2012 Axeda Corporation. All rights reserved. Confidential property.
System Configuration Properties (continued.)PropertyDescriptionDevice communicationnotification maximum e-maillengthThe maximum number of bytes for an e-mail message. The default value (10000) limitsthe size of e-mail messages to 10K. To allow unlimited-length messages, use a settingof -1.Device conditionsynchronization processsettingThe process missing device task synchronizes the device condition with device missingstatus if the flag is true. The process does not synchronize the device condition withdevice missing status if the flag is false. The default is true.Device updatesynchronization delayNumber of seconds between checks by the asset context cache for asset updates inthe database.Device Updates export rootThe server directory to which the server saves the tar .gz file intended for export to aspecified asset during an Axeda Transport - Export session. This file contains allqueued server commands and eMessages, as well as any pending actions ordownload instructions for the asset.The file for export is stored in a new subdirectory named for the export session.Device Updates import rootThe server directory to which the server will save files imported from a specified assetduring an Axeda Transport - Import session. The server store the imported file to a newsubdirectory named for the import session.Direct protocols allowedTrue (default) for the server to accept direct protocol connections. (The agent uses the“direct connect” protocol in remote sessions.)False for the server to prohibit direct protocol connections from agents and ignore thefollowing direct connect properties: directConnectPort and directConnectSSLPort.Disable notification ondevice registrationTrue to include all newly registered assets in notifications for all users. False is thedefault setting, which means that all newly registered assets are excluded fromnotifications for all users.Display PathThe path where displays created using Axeda Builder are stored for access from theService application.Duplicate data item valuecheckIndicates if the system inserts duplicate data items that have the same timestamp.E-mail serverName of e-mail server to use for sending e-mail messages. Specify the completeserver path; for example, usmail2.Axeda.com.eMessage persistentconnectionSpecifies whether or not to require a persistent HTTP connection:If true, the system will process the duplicate data items that have the same timestamp.If false (the default), the system will not process the duplicate timestamp data itemmessages. False (default) to not require a persistent HTTP connection (HTTP 1.1 only) True if you are using HTTP 1.1 and require a persistent HTTP connection.eMessage timeoutThe number of seconds that the Enterprise server waits before closing the connectionto the asset, allowing enough time for a message being sent from the asset to theEnterprise server to complete.eMessage will overwritedevice time zoneTrue (default) for the eMessage from the asset (registration message) to overwrite thesetting for the asset’s time zone (as stored in the Enterprise server database).Enable alarm rulesTrue to enable the processing of alarm triggers (default), or false to disable processing.Note: If you are not going to need these triggers, set this to false to improve systemperformance.7Copyright 2000-2012 Axeda Corporation. All rights reserved. Confidential property.
System Configuration Properties (continued.)PropertyEnable data rulesDescriptionTrue to enable the processing of data triggers (default), or false to disable theprocessing.Note: If you are not going to need these triggers, set this to false to improve systemperformance.Enable Cross-Site Scripting(XSS) FilterIf True (the default), the XSS filter servlet is enabled and will scan for cross-sitescripting (XSS) exploits. The filter will use a RegEx-based approach to detectattempted exploits.When the filter is enabled, all requests must meet the following criteria or they will beprevented from accessing the server: The URI must be present in the Whitelist (defined by the property “XSS white list filename”) The request must be in the form POST executed during a valid WizardContext The parameter being inspected must be one of a set of "known" URL constants,which are derived from the QueryParameter and MruKey classes.In the event that an exploit has been detected, the server will log the attempt and logout the related user. If False, Cross-Site Scripting filter is disabled.Enable/Disable Extended UIModule FeatureTrue if the Platform supports Extended UI Modules; false if the Platform does notsupport Extended UI Modules. The default is true.Extended UI Module loadtimeoutSpecifies the number of seconds during which time the server will attempt to load anextended UI module before it times out. The default is 30 (seconds).Enable forgot passwordfeatureTrue (default) sets the reset password link as visible.Enable registration rulesTrue to enable the processing of asset registration events as triggers (default), or falseto disable the processing.Note: If you are not going to need these triggers, set this to false to improve systemperformance.Enable schedule rulesTrue to enable schedule triggers; false to disable schedule triggers (default).Note: If you are not going to need these triggers, set this to false to improve systemperformance.Enable SOAP status rulesTrue to enable the processing of SOAP status events as triggers (default), or false todisable the processing.Note: If you are not going to need these triggers, set this to false to improve systemperformance.Enable Soundex FeatureFalse (default) to disable Soundex functionality for searching for and displaying data;True to enable the server to implement Soundex functionality when searching thedatabase.Enable the SFTP serverfuntionalityEnable the SFTP server functionality.Enable writing data to fileshould processing failIf true, data that could not be inserted in the database is saved to a backup file; if false,the data is not saved if the database insert fails. Default is false (data not saved tobackup file).Endpoint of the ActiveMQinstance, in URI formThe endpoint of the ActiveMQ instance, in the form of a URI. The default setting is tcp://localhost:61616.8Copyright 2000-2012 Axeda Corporation. All rights reserved. Confidential property.
System Configuration Properties (continued.)PropertyDescriptionEndpoint to connect toActiveMQ JMX, in URI formThe endpoint to connect to ActiveMQ JMX, in URI form. The default setting rmi. If the machinerunning ActiveMQ is not the same as the machine running the Enterprise server,replace localhost with the name of the machine where ActiveMQ is running.Otherwise, keep this setting as is.Enterprise Server host nameThe name of the cluster that this Axeda Enterprise server belongs to. This name doesnot need to correspond to a machine name. All Axeda Enterprise servers thatcommunicate with the same database (that is, are in the same cluster) must have thesame name. Each cluster must have a unique name. Note that the pound sign (#) is areserved character and should not be used in the name. The name specified here doesnot have to correspond to a machine name.Important! This value must be set for the server to start up. On start up, the server nowensures that critical properties are set (currently, there are only two - this one and thecom.axeda.drm.db.dataSource property). If they are not, the server will not start.ESS default protocol URIThe default URI for the ESS protocol.ESS JMS message TTL inmillisecondsThe number of milliseconds that a JMS message is allowed to remain alive. The defaultvalue is 20 minutes.Event subscription QueueCleanup thread frequency insecondsThe number of minutes that the Reaper thread waits between each check forsubscriptions that have expired. Each time it finds expired subsriptions, it deletes them.The default value is 1800 seconds (30 minutes).Event subscription QueueTime-To-Live in secondsThe number of minutes that a subscription is allowed to remain alive. The default valueis 1200 seconds (20 minutes).Exclude default group fromnotificationsTrue to exclude all users from asset group security-based notifications who belong todefault asset group only, for a specific model. False to include all users show aredefined only in default asset group for particular model. True is the default setting,which means if a user is included in the default asset group for a model and in no otherasset group settings for that mode, that user will not receive notifications for the relatedasset.Extended UI Module loadtimeoutSpecifies the number of seconds during which time the Platform will attempt to load anextended UI module before it times out. The default is 30 (seconds).Extension of the file used tostore data should an insertfailIf the server is set to save data to a backup file when it can’t insert that data in thedatabase, it will save that data to a file of this type, and create that file if needed. Forexample. csv or txt. Make sure com.axeda.drm.data.failed insert.enable is set to true.File download base directoryThe path to the download directory for the Enterprise server.File upload base directoryThe path to the upload directory for the Enterprise server. Be sure to use forwardslashes in the path, no matter which operating system is hosting your EnterpriseServer.Filter non-ascii charactersfrom device dataTrue to enable the filtering of non-ASCII characters or false to disable filtering.Filter substitute characterThe character that replaces non-ASCII characters when filtering is enabled.9Copyright 2000-2012 Axeda Corporation. All rights reserved. Confidential property.
System Configuration Properties (continued.)PropertyForced ping intervalDescriptionThe maximum amount of time allowed for a managed asset to be silent (that is, notsending messages to the Axeda Enterprise server).Normally, when a managed asset has no data to send, the Axeda Agent managing thatasset sends a brief ping message based on a configured ping rate. However, if amanaged asset is deleted on the Enterprise server and the agent sends no data for thatasset, the asset becomes hidden such that it exists, from the agent's perspective, but isnot visible in the Enterprise server.Note: To make a hidden asset reappear, the agent must send an explicit message (aforced ping) on behalf of the asset, so that the Enterprise server can re-register it.Frequency threads for pollfor updates in millisecondsDefault is 500 milliseconds.Global Access Serveractivity monitor cleanupperiodThe number of hours that the Activity Monitor will wait before cleaning out inactivesessions. Identifies how frequently the activity monitor runs and cleans up (removes)unused or abandoned sessions. The default is every 720 (seconds).Global Access Server agentserialThe serial number of the Agent that has been deployed on the Remote Server.Global Access Server autoregisterTrue to allow remote servers to register themselves with the Axeda Enterprise server;false to require that someone register them manually.Global Access Serverdetermined by the user'stime zoneTrue to use the user’s time zone to determine which Global Access Server (GAS) touse; false (default) to find the GAS using the default algorithm. The default algorithmuses the time zone offset value of the GAS and the asset to determine theirgeographical location. The algorithm then uses the geographical location, the currentload, and maximum supported load to determine the GAS to use.Global Access Server DNSname (IP) usable by allusersAn IP address that all users can access for Remote Sessions.Global Access Serverexternal addressAn IP address that can be used for Remote Sessions from machines that are notrunning Axeda Agents.Global Access Serverhostname that the userconnects toTrue (default) to allow the remote server user connect url to be visible.Global Access Serverinternal nam
Allow users to remove partner accounts True to enable users to remove partners defined in the server from the server. False (default) to prevent Applications users from deleting partners. Users also need the privilege, Partner Login - Remove Partner Account, to be able to remove Partner Login accounts. Allow users to remove remote Enterprise .
When provisioning a Windows Server for a specific role there are additional items to consider for further securing the server. When planning and provisioning your server layout, designate one primary purpose per server. Whenever possible, designate one server as the database server, one server as the web server, and one server as the file server.
Server 2005 , SQL Server 2008 , SQL Server 2008 R2 , SQL Server 2012 , SQL Server 2014 , SQL Server 2005 Express Edition , SQL Server 2008 Express SQL Server 2008 R2 Express , SQL Server 2012 Express , SQL Server 2014 Express .NET Framework 4.0, .NET Framework 2.0,
Configuration using a single DataLink Server and a single database The default DataLink Server configuration installs DataLink Server on a deployment where a single DataLink Server and single database are used by default. MagicInfo Player MagicInfo Player DataLink Server DataLink Server Configuration using a single DataLink Server and multiple .
Sybase Adaptive Server Enterprise 11.9.x-12.5. DOCUMENT ID: 39995-01-1250-01 LAST REVISED: May 2002 . Adaptive Server Enterprise, Adaptive Server Enterprise Monitor, Adaptive Server Enterprise Replication, Adaptive Server Everywhere, Adaptive Se
Cisco 3560 & 3750 NetFlow Configuration Guide Cisco Nexus 7000 NetFlow Configuration Cisco Nexus 1000v NetFlow Configuration Cisco ASR 9000 NetFlow Configuration Appendix. 3 Cisco NetFlow Configuration Cisco IOS NetFlow Configuration Guide Netflow Configuration In configuration mode issue the following to enable NetFlow Export:
Introduction 1-2 Oracle Forms Server and Reports Server Installation Guide Introduction Oracle Forms Server and Reports Server is an integrated set of database tools i Oracle Forms i. Oracle Forms Server Server and Reports Server Server. UNIX. Installation Guide Compaq Tru64 .
Administrasi Server Sementara itu peta konsep mata pelajaran menjelaskan struktur urutan kegiatan belajar dan topik materi pelajaran. Gambar 2 dibawah ini menjelaskan peta konsep mata pelajaran Administrasi Server kelas XI semester 2. Administrasi Server 2 1. Server FTP 2. Server e-Mail 3. Server WebMail 4. Server Remote 5. Server NTP 6. Server .
in advanced mathematics used in US universities are also popular in Australian universities for students studying engineering and some areas of applied sciences. However, the advanced mathematics .
