Riptide Terrova Installation Instrucitons
RIPTIDE TERROVABOW-MOUNT TROLLING MOTORInstallation Instructions
INTRODUCTIONTHANK YOUThank you for choosing Minn Kota. We believe that you should spend more time fishing and less time positioning your boat. That’s whywe build the smartest, toughest, most intuitive trolling motors on the water. Every aspect of a Minn Kota trolling motor is thought outand rethought until it’s good enough to bear our name. Countless hours of research and testing provide you the Minn Kota advantagethat can truly take you “Anywhere. Anytime.” We don’t believe in shortcuts. We are Minn Kota. And we are never done helping you catchmore fish.REGISTRATIONRemember to keep your receipt and immediately registeryour trolling motor. A registration card is included with yourmotor or you can complete registration on our website atminnkotamotors.com/register.SERIAL NUMBERYour Minn Kota 11-character serial number is very important.It helps to determine the specific model and year ofmanufacture. When contacting Consumer Service or registeringyour product, you will need to know your product’s serialnumber. We recommend that you write the serial number downso that you have it available for future reference.Made by Minn KotaJohnson OutdoorsMarine Electronics, Inc.121 Power DriveMankato, MN 56001 USATrolling MotorsProduced in XXXXPRODUCT DESCRIPTIONMODEL XXXXXXXXXV DCXX ASER NO YYDDDC00000EXAMPLENOTICE: The serial number on your Riptide Terrova islocated inside the mount below the motor rests.MOTOR INFORMATION (For Consumer Reference Only)Model:Serial Number:Purchase Date:Store Where Purchased:NOTICE: Do not return your Minn Kota motor to your retailer. Your retailer is not authorized to repair or replace this unit.You may obtain service by: calling Minn Kota at (800) 227-6433; returning your motor to the Minn Kota Factory Service Center;sending or taking your motor to any Minn Kota authorized service center. A list of authorized service centers is available on ourwebsite, at minnkotamotors.com. Please include proof of purchase, serial number and purchase date for warranty service with anyof the above options.2 minnkotamotors.com 2022 Johnson Outdoors Marine Electronics, Inc.
SAFETY CONSIDERATIONSPlease thoroughly read the user manual. Follow all instructions and heed all safety and cautionary notices. Use of this motor is onlypermitted for persons that have read and understood these user instructions. Minors may use this motor only under adult supervision.WARNINGYou are responsible for the safe and prudent operation of your vessel. We have designed your Minn Kota product to be an accurateand reliable tool that will enhance boat operation and improve your ability to catch fish. This product does not relieve you from theresponsibility for safe operation of your boat. You must avoid hazards to navigation and always maintain a permanent watch so you canrespond to situations as they develop. You must always be prepared to regain manual control of your boat. Learn to operate your MinnKota product in an area free from hazards and obstacles.WARNINGNever run the motor out of the water, as this may result in injuries from the rotating propeller. The motor should be disconnected fromthe power source when it is not in use or is off the water. When connecting the power-supply cables of the motor to the battery, ensurethat they are not kinked or subject to chafe and route them in such a way that persons cannot trip over them. Before using the motormake sure that the insulation of the power cables is not damaged. Disregarding these safety precautions may result in electric shortsof battery(s) and/or motor. Always disconnect motor from battery(s) before cleaning or checking the propeller. Avoid submerging thecomplete motor as water may enter the lower unit through control head and shaft. If the motor is used while water is present in the lowerunit considerable damage to the motor can occur. This damage will not be covered by warranty.WARNINGTake care that neither you nor other persons approach the turning propeller too closely, neither with body parts nor with objects.The motor is powerful and may endanger or injure you or others. While the motor is running watch out for persons swimming and forfloating objects. Persons who lack the ability to run the motor or whose reactions are impaired by alcohol, drugs, medication, or othersubstances are not permitted to use this motor. This motor is not suitable for use in strong currents. The constant noise pressure level ofthe motor during use is less than 70dB(A). The overall vibration level does not exceed 2,5 m/sec2.WARNINGWhen stowing or deploying the motor, keep fingers clear of all hinge and pivot points and all moving parts. In the event of unexpectedoperation, remove power leads from the battery.WARNINGIt is recommended to only use Johnson Outdoors approved accessories with your Minn Kota motor. Using non-approved accessoriesincluding to mount or control your motor may cause damage, unexpected motor operation and injury. Be sure to use the product andapproved accessories, including remotes, safely and in the manner directed to avoid accidental or unexpected motor operation. Keep allfactory installed parts in place including motor and accessory covers, enclosures and guards. 2022 Johnson Outdoors Marine Electronics, Inc.minnkotamotors.com 3
KNOW YOUR rdGunwaleTransomSternGunwaleBowSternHull4 minnkotamotors.com 2022 Johnson Outdoors Marine Electronics, Inc.
INSTALLATIONINSTALLING THE RIPTIDE TERROVAYour new Riptide Terrova comes with everything you’ll need to directly install it to the boat. This motor can be directly mounted to theboat or coupled with a Minn Kota quick release bracket for ease of mounting and removal. For installation with a quick release bracket,refer to the installation instructions provided with the bracket. For compatible quick release mounting brackets and to locate yournearest dealer, visit minnkotamotors.com. To install the motor directly to the boat, please follow the instructions provided in this manual.Please review the parts list, mounting considerations and tools needed for installation prior to getting started. For additional productsupport, please visit minnkotamotors.com.INSTALLATION PARTS LISTItem /AssemblyPart #AA2994864BAG ASSEMBLY - (BOLT, NUT, WASHERS)112263462BOLT-MOUNTING-1/4X2 W/STG622261713WASHER-1/4632263103NUT NYLOK 1/4-20 MTG642301720WASHER-MOUNTING RUBBER65 MOTOR ASSEMBLY16Description2390800 t LANYARD, REMOTE W/ CARABEENERQty.2994075 tREMOTE ASY, IPILOT1p2397106 tMANUAL, QUICK REF., IPILOT 1.6182994076 ÂREMOTE ASSEMBLY LINK TOUCHSCREEN192373241 ÂCABLE, USB REMOTE CHARGER LINK1102375901 ÂADAPTER, USB DC POWER LINK12996400 t HEADING SENSOR ASSEMBLY*SELECT MODELS ONLY*12490389-1 Â14151617811121711761CABLE, ETH (M12-M-M12-F, 30'12092600PIN-DRIVE 1.06" LG (SS)12262658PIN-DRIVE 1" X 3/16" S/S12151726WASHER-5/16 STD (S/S)12091701WASHER-PROP (LARGE)12053101NUT PROP, NYLOCK (MED) 5/16-24 SS12093101NUT-PROP, NYLOCK, LG MX101 318 SS12091161PROP-WW2 3 5/8" MACHINED12341161PROP-WW2 4.5" WELDED12331161PROP-WW2 4" WELDED1TRANSMITTER ASY,TRRV CPLT1182994095 lBB1378131PROP IND 2091160 WDLS WDG II1CC1378160PROP KIT 2341160 112# WW2118541AADD1378132PROP IND 233160 WDLS WDG II1p2327132INSTALLATION INSTRUCTIONS TERROVA12p2397107 ÂMANUAL, QUICK REF., IPILOT LINK 3.013l Only available with models factory installed with CoPilot.p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually.t Only available with models factory installed with i-Pilot. Only available with models factory installed with i-Pilot Link. 2022 Johnson Outdoors Marine Electronics, Inc.91015161417BBCCDDminnkotamotors.com 5
INSTALLING THE RIPTIDE TERROVAMOUNTING CONSIDERATIONSIt is recommended that the motor be mounted as close to the centerline of the boat aspossible. Make sure the area under the mounting location is clear to drill holes and installnuts and washers. Make sure the motor rest is positioned far enough beyond the edge ofthe boat. The motor must not encounter any obstructions as it is lowered into the wateror raised into the boat when stowed and deployed. Consider a quick release or adapterbracket with the installation of your motor. To view a list of accessories, please visitminnkotamotors.com.View accessoriesavailable for yourtrolling motor atminnkotamotors.com.TOOLS AND RESOURCES REQUIRED #3 Phillips Screw Driver Drill 9/32” Drill Bit 7/16” Box End Wrench A second person to help with the installationINSTALLATIONINSTALLING THE RIPTIDE TERROVA1a.Place the mount on an elevated, level surface suchas a workbench or the tailgate of a pickup. Themotor, as removed from the box, should be in thestowed position.b.Remove the four sideplate screws using a #3 Phillipsscrewdriver. Two of these screws will be located oneach side of the mount.1bNOTICE: This motor weighs approximately 65lbs.Minn Kota recommends having a second person helpwith the installation.Sideplate ScrewDeployed6 minnkotamotors.comStowed 2022 Johnson Outdoors Marine Electronics, Inc.
INSTALLING THE RIPTIDE TERROVA2c.Remove the Right Sideplate.d.Swing the Left Sideplate out and away from theBase Extrusion.2d2cBase ExtrusionLeft SideplateRight Sideplate3e.Make sure that the Power Cables from the batteryare disconnected, or that the breaker,if equipped, is "off."Power CablesWARNINGMake sure the motor is mounted on a level surface and is notconnected to a power source.4f.Place the mount as close to the centerline or keelof the boat as possible. The motor can be installedon either the Port or Starboard side of the boatbased on personal preference. Check placementwith the motor in the stowed and deployed positions.Review the mounting considerations at thebeginning of the installation. 2022 Johnson Outdoors Marine Electronics, Inc.KeelDeck of Boatminnkotamotors.com 7
INSTALLING THE RIPTIDE TERROVA5ITEM(S) NEEDED#4 x 6g.When the motor is in the deployed position, makesure that the Shaft is 1-1/2" out past the Gunwale ofthe boat. The lower unit, when stowed and deployedmust not encounter any obstructions.h.Check to be sure that the mount is level. Use theRubber Washers (Item #4) provided to create a levelsurface if necessary.Gunwale1-1/2"MinimumShaft6i.It is recommended to mark at least 4 of the 6 holesin the Base Extrusion and to have a minimum oftwo bolts on each side that are located the farthestapart. Ideal installation would allow for 6 bolts to beused, with a minimum of 4.j.Drill through the deck of the boat using a 9/32" DrillBit on the marked locations.Drilling LocationsBase ExtrusionDrilling Locations8 minnkotamotors.com 2022 Johnson Outdoors Marine Electronics, Inc.
INSTALLING THE RIPTIDE TERROVA7ITEM(S) NEEDED#1 x 6#2 x 6#3 x 6k.Put a 1/4-20 x 3 1/2" (Item #1) screw in each of thedrilled locations. The screw should pass throughthe Base Extrusion and the boat deck. If the rubberwashers (Item #4) are used, they should sit betweenthe Base Extrusion and boat deck. Make sure tosecure the motor with screws on each side of theBase Extrusion.l.Place a Flat Washer (Item #2) and then a Nylock Nut(Item #3) at the end of each screw as shown andsecure. Make sure all hardware is secure.#4 x 6ScrewBoatDeckNOTICE: To prevent seizing of the stainless steelhardware, do not use high speed installation tools.Wetting the screws or applying an anti-seize may helpprevent seizing.8m. Replace the Right Sideplate.n.RubberWasherNylock NutFlat Washer8nSwing the Left Sideplate back into its correctposition on the Base Extrusion.8mBase ExtrusionLeft SideplateRight Sideplate 2022 Johnson Outdoors Marine Electronics, Inc.minnkotamotors.com 9
ROUTING THE i-PILOT LINK CABLE9o.Replace the four sideplate screws using a #3 or #2Phillips screwdriver. Two of these screws will belocated on each side of the mount.Sideplate ScrewROUTING THE i-PILOT LINK CABLEYour trolling motor may be pre-installed with either i-Pilot or i-Pilot Link. To learn more about the GPS capabilities available with youri-Pilot or i-Pilot Link navigation system, please refer to the corresponding Owner's Manual by visiting minnkotamotors.com.The i-Pilot Link features require a cable to be connected to an output device. This connection is present on the trolling motor below theControl Head, if installed. The i-Pilot system does not need an external wired connection. If only one connection is present, your motoris equipped with the i-Pilot Link system. If no connections are present, your motor may or may not be installed with i-Pilot. Please followthe Minn Kota recommendations on routing the cables to optimize mobility and maximize functionality. The routing will be the sameregardless of the number of cables present. Use the following instructions to properly route cables.Cables are shielded to minimize interference. To protect thisshielding the cables should not be pulled tight against sharpangles or hard objects. If using cable ties, do not over-tighten.Any excess cable should be bundled in a loose loop of no less than4” in diameter.To minimize trolling motor interference, ensure that the fish finderand trolling motor are powered by separate batteries. Please referto the Battery & Wiring Installation and Motor Wiring Diagramsections of this manual for correct rigging instructions.10 minnkotamotors.comEight PinConnectori-Pilot LinkCablei-Pilot Link Cablefrom Control HeadLocking Collar 2022 Johnson Outdoors Marine Electronics, Inc.
ROUTING THE i-PILOT LINK CABLE1a.Place the motor in the deployed position.b.Locate the i-Pilot Link cable, at the base of theControl Head.Control Headi-PilotLinkCAUTIONNot following the recommended wire routing for the i-PilotLink cable, if equipped, may cause damage to the productand void your product warranty. Route cables away frompinch points or other areas that may cause them to bendin sharp angles. Routing the cables in any way other thandirected may cause damage to the cables by being pinchedor severed.c.The i-Pilot Link cable should be fed all the waythrough the Coil Cord. It should exit the Coil Cordat the bottom of the Coil Cord, where it connects tothe Mount.Coil CordMountNOTICE: After the i-Pilot Link Cable exits the Coil Cord,it should be routed through an established routing systemon the boat, in an area with minimal interference. Inspectthe selected route carefully to ensure that there are nosharp edges, obstacles, or obstructions that may damagethe cables. 2022 Johnson Outdoors Marine Electronics, Inc.minnkotamotors.com 11
INSTALLING THE PROPINSTALLING THE PROP1ITEM(S) NEEDED#17 x 1#15 x 1#16 x 1#14 x 1CAUTION1aArmature ShaftDrive PinDisconnect the motor from the battery before beginning anyprop work.a.Take the Drive Pin (Item #14) and slide it throughthe Hole in the Armature Shaft. Position the DrivePin horizontal by grasping the Armature Shaft androtating it with the Drive Pin in place.b.Align the Propeller (Item #17) so it is also horizontaland parallel with the Drive Pin. Slide the Propelleronto the Armature Shaft and Drive Pin until it isseated against the lower unit.c.Install the Prop Washer (Item #15) and the Prop Nut(Item #16) onto the end of the Armature Shaft.d.Holding the end of the Armature Shaft with a FlatBlade Screwdriver, tighten the Prop Nut with a 9/16"Open End Wrench.e.PropellerTighten the Prop Nut 1/4 turn past snug to25-35 in-lbs.CAUTIONDo not over tighten as this can damage the prop.12 minnkotamotors.comProp WasherProp Nut1bPropeller1dProp NutProp WasherPropellerDrive Pin 2022 Johnson Outdoors Marine Electronics, Inc.
BATTERY & WIRING INSTALLATIONBOAT RIGGING & PRODUCT INSTALLATIONFor safety and compliance reasons, we recommend that you follow American Boat and Yacht Council (ABYC) standards when riggingyour boat. Altering boat wiring should be completed by a qualified marine technician. The following specifications are for generalguidelines only:CAUTIONThese guidelines apply to general rigging to support your Minn Kota motor. Powering multiple motors or additional electrical devicesfrom the same power circuit may impact the recommended conductor gauge and circuit breaker size. If you are using wire longer thanthat provided with your unit, follow the conductor gauge and circuit breaker sizing table below. If your wire extension length is more than25 feet, we recommend that you contact a qualified marine technician.CAUTIONAn over-current protection device (circuit breaker or fuse) must be used. Coast Guard requirements dictate that each ungroundedcurrent-carrying conductor must be protected by a manually reset, trip-free circuit breaker or fuse. The type (voltage and current rating)of the fuse or circuit breaker must be sized accordingly to the trolling motor used. The table below gives recommended guidelines forcircuit breaker sizing.CONDUCTOR GAUGE AND CIRCUIT BREAKER SIZING TABLEThis conductor and circuit breaker sizing table is only valid for the following assumptions:1.2.3.No more than 2 conductors are bundled together inside of a sheath or conduit outside of engine spaces.Each conductor has 105 C temp rated insulation.No more than 5% voltage drop allowed at full motor power based on published product power requirements.Motor Thrust / ModelMaxAmp Draw30 lb.3040 lb., 45 lb.4250 lb., 55 lb.5060 Amp @ 12 VDC70 lb.4250 Amp @ 24 VDC80 lb.5660 Amp @ 24 VDC101 lb.46Engine Mount 10150Circuit BreakerWire Extension Length5 feet10 feet15 feet20 feet25 feet10 AWG10 AWG8 AWG6 AWG4 AWG10 AWG8 AWG6 AWG4 AWG4 AWG8 AWG6 AWG4 AWG4 AWG2 AWG10 AWG10 AWG8 AWG8 AWG6 AWG8 AWG8 AWG8 AWG6 AWG6 AWG50 Amp @ 36 VDC8 AWG8 AWG8 AWG8 AWG8 AWG60 Amp @ 36 VDC8 AWG8 AWG8 AWG8 AWG8 AWG50 Amp @ 12 VDC112 lb.5260 Amp @ 36 VDC8 AWG8 AWG8 AWG8 AWG8 AWGEngine Mount 160116(2) x 60 Amp @ 24 VDC6 AWG6 AWG4 AWG2 AWG2 AWGE-Drive4050 Amp @ 48 VDC10 AWG10 AWG10 AWG10 AWG10 AWGNOTICE: Wire Extension Length refers to the distance from the batteries to the trolling motor leads. Consult website for availablethrust options. Maximum Amp Draw values only occur intermittently during select conditions and should not be used as continuousamp load ratings.ReferenceUnited States Code of Federal Regulations: 33 CFR 183 – Boats and Associated Equipment ABYC E-11: AC and DC Electrical Systems on Boats 2022 Johnson Outdoors Marine Electronics, Inc.minnkotamotors.com 13
SELECTING THE CORRECT BATTERIESSELECTING THE CORRECT BATTERIESThe motor will operate with any lead acid, deep cycle marine 12 volt battery/batteries. For best results, use a deep cycle, marine batterywith at least a 105 amp-hour rating. Maintain battery at full charge. Proper care will ensure having battery power when you need it, andwill significantly improve the battery life. Failure to recharge lead-acid batteries (within 12-24 hours) is the leading cause of prematurebattery failure. Use a multi-stage charger to avoid overcharging. We offer a wide selection of chargers to fit your charging needs. If youare using a crank battery to start a gasoline outboard, we recommend that you use a separate deep cycle marine battery/batteries foryour Minn Kota trolling motor. For more information on battery selection and rigging, please visit minnkotamotors.com. Minn Kota trollingmotors can run on Lithium-Ion batteries. However, they are specifically designed to run on traditional lead-acid batteries (flooded, AGMor GEL). Lithium-Ion batteries maintain higher voltages for longer periods of time than lead acid. Therefore, running a Minn Kota trollingmotor at speeds higher than 85% for a prolonged period could cause permanent damage to the motor.WARNINGNever connect the ( ) and the (–) terminals of the same battery together. Take care that no metal object can fall onto the battery andshort the terminals. This would immediately lead to a short and extreme fire danger.CAUTIONRefer to “Conductor Gauge and Circuit Breaker Sizing Table” in the previous section to find the appropriate circuit breaker or fuse foryour motor. For motors requiring a 60-amp breaker, the Minn Kota MKR-19 60-amp circuit breaker is recommended.CAUTIONPlease read the following information before connecting your motor to your batteries in order to avoid damaging your motor and/orvoiding your warranty.ADDITIONAL CONSIDERATIONSUsing DC or Alternator ChargersYour Minn Kota trolling motor may be designed with an internal bonding wire to reduce sonar interference. Most alternator charging systemsdo not account for this bonding wire, and connect the negative posts of the trolling motor batteries to the negative posts of the crank/starting battery. These external connections can damage connected electronics and the electrical system of your trolling motor, voidingyour warranty. Review your charger’s manual carefully or consult the manufacturer prior to use to ensure your charger is compatible.Minn Kota recommends using Minn Kota brand chargers to recharge the batteries connected to your Minn Kota trolling motor, as theyhave been engineered to work with motors that include a bonding wire.14 minnkotamotors.com 2022 Johnson Outdoors Marine Electronics, Inc.
CONNECTING THE BATTERIESAdditional Accessories Connected to Trolling Motor BatteriesSignificant damage to your Minn Kota motor, your boat electronics, and your boat can occur if incorrect connections are made betweenyour trolling motor batteries and other battery systems. Minn Kota recommends using an exclusive battery system for your trollingmotor. Where possible, accessories should be connected to a separate battery system. Radios and sonar units should not be connectedto any trolling motor battery systems as interference from the trolling motor is unavoidable. If connecting any additional accessories toany trolling motor battery system, or making connections between the trolling motor batteries and other battery systems on the boat, besure to carefully observe the information below.The negative (-) connection must be connected to the negative terminal of the same battery that the trolling motor negative leadconnects to. In the diagrams below this battery is labeled “Low Side” Battery. Connecting to any other trolling motor battery will inputpositive voltage into the “ground” of that accessory, which can cause excess corrosion. Any damage caused by incorrect connectionsbetween battery systems will not be covered under warranty.Automatic Jump Start Systems and Selector SwitchesAutomatic jump start systems and selector switches tie the negatives of the connected batteries together. Connecting these systemsto the “High Side” Battery or “Middle” Battery in the diagrams below and will cause significant damage to your trolling motor andelectronics. The only trolling motor battery that is safe to connect to one of these systems is the “Low Side” Battery.CONNECTING THE BATTERIES12-Volt Systems1.2.3.Make sure that the motor is switched off (speed selector on “OFF” or “0”).Connect positive ( ) red lead to positive ( ) battery terminal.Connect negative ( – ) black lead to negative ( – ) battery terminal.WARNINGFor safety reasons do not switch the motor on until the propeller is in the water. If installing a leadwire plug, observe proper polarity andfollow instructions in your boat owner’s manual. 2022 Johnson Outdoors Marine Electronics, Inc.minnkotamotors.com 15
CONNECTING THE BATTERIES IN SERIESCONNECTING THE BATTERIES IN SERIES(IF REQUIRED FOR YOUR MOTOR)24-Volt SystemsTwo 12-volt batteries are required. The batteries must be wired inseries, only as directed in the wiring diagram, to provide 24 volts.To trolling motor negative1. Make sure that the motor is switched off (speed selector on “0”). 24 Volts to trolling motorpositive (or circuit breaker)24 Volt Series Connection2. Connect a connector cable to the positive ( ) terminal ofbattery 1 and to the negative ( – ) terminal of battery 2.3. Connect positive ( ) red motor lead to positive ( ) terminalon battery 2.4. Connect negative ( – ) black motor lead to negative ( – ) terminalof battery 1.Neg -Pos Battery #1(Low Side)Neg -Pos Battery #2(High Side)Two 12-volt batteries connected in series for 24 voltsWARNINGFor safety reasons do not switch the motor on until the propeller is in the water. If installing a leadwire plug, observe proper polarity andfollow instructions in your boat owner’s manual.WARNING For safety reasons, disconnect the motor from the battery or batteries when the motor is not in use or while the battery/batteriesare being charged. Improper wiring of 24/36 volt systems could cause battery explosion. Keep leadwire wing nut connections tight and solid to battery terminals. Locate battery in a ventilated compartment.16 minnkotamotors.com 2022 Johnson Outdoors Marine Electronics, Inc.
CONNECTING THE BATTERIES IN SERIES36-Volt SystemsThree 12-volt batteries are required. The batteries must be wired in series, only as directed in the wiring diagram, to provide 36 volts.1.2.Make sure that the motor is switchedoff (speed selector on “0”).Connect a connector cable to thepositive ( ) terminal of battery 1 andto the negative ( – ) terminal of battery 2and another connector cable from the positive( ) terminal of battery 2 to the negative ( – )terminal of battery of battery 3.3.Connect positive ( ) red motor leadto positive ( ) terminal on battery 3.4.Connect negative ( – ) black motor lead tonegative ( – ) terminal of battery 1. 36 Volts to trolling motorpositive (or circuit breaker)To trolling motor negative24 Volt Series ConnectionNeg -Pos Battery #1 (Low Side)Neg -36 Volt Series ConnectionPos Battery #2 (Middle)Neg -Pos Battery #3 (High Side)Three 12-volt batteries connected in series for 36 voltsWARNINGFor safety reasons, do not switch the motor on until the propeller is in the water. If installing a leadwire plug, observe proper polarity andfollow instructions in your boat owner’s manual.WARNING For safety reasons, disconnect the motor from the battery or batteries when the motor is not in use or while the battery/batteriesare being charged. Improper wiring of 24/36 volt systems could cause battery explosion. Keep leadwire wing nut connections tight and solid to battery terminals. Locate battery in a ventilated compartment.This completes the installation of your Terrova. A complete Owner’s Manualcan be downloaded at minnkotamotors.com. 2022 Johnson Outdoors Marine Electronics, Inc.minnkotamotors.com 17
RECOMMENDED ACCESSORIESON-BOARD & PORTABLE BATTERY CHARGERSStop buying new batteries and start taking care of the ones you’ve got. Many chargers can actually damage yourbattery over time – creating shorter run times and shorter overall life. Digitally controlled Minn Kota chargers aredesigned to provide the fastest charge that protect and extend battery life.MK212PCMK210DMK110PDTALON SHALLOW WATER ANCHORIntroducing the all-new, sleek redesigned Talon. Talon is the only shallow water anchor with up to 15’ of anchoringdepth, multiple anchoring modes, and control from the bow, transom, console, remote or mobile device.BUILT-INWORK LIGHTUP TO 15’ DEEPLets you tie lines and work fromthe transom any time of day —or night. Includes both whiteand blue LED lights with threebrightness settings.BLUETOOTH CONNECTIVIT YLets you control Talon from yourmobile device and easily update it.Also opens up communication toother control options.Control more water and catchmore fish with the first 15’shallow water anchor.MORE CONTROLOPTIONS Control PanelWireless RemoteMobile AppWireless Foot SwitchHumminbird Connectivityi-Pilot &i-Pilot LinkTM RemoteMINN KOTA ACCESSORIESWe offer a wide variety of trolling motor accessories, including: 60-Amp Circuit BreakerMounting BracketsStabilizer KitsExtension Handlesminnkotamotors.comPart #2327133 Battery Connectors Battery Boxes Quick Connect PlugsMinn Kota Consumer & Technical ServiceJohnson Outdoors Marine Electronics, Inc.PO Box 8129Mankato, MN 56001ECN 42100121 Power DriveMankato, MN 56001Phone (800) 227-6433Fax (800) 527-4464 2022 Johnson Outdoors Marine Electronics, Inc.All rights reserved.Rev E04/22
RIPTIDE TERROVAMOTEUR DE PÊCHE À LA TRAÎNE MONTÉ SUR L’ÉTRAVEManuel du Propriétaire
PRÉSENTATIONMERCINous vous remercions d’avoir choisi Minn Kota. Nous sommes persuadés que vous devriez consacrer plus de temps à pêcher et moins detemps à amarrer votre embarcation. C’est pourquoi nous construisons les propulseurs électriques les plus intelligents, les plus solides etles plus faciles à utiliser. Chaque aspect d’un propulseur électrique Minn Kota est réfléchi et étudié jusqu’à ce qu’il soit digne de porternotre nom. Nous avons investi des heures incalculables de recherche et d’essais pour vous offrir les avantages caractéristiques de MinnKota, qui vous mène vraiment n’importe où, et n’importe quand. Notre principe est simple, nous faisons les choses selon les règles. Noussommes Minn Kota. Et nous ne cesserons jamais de vous aider à pêcher plus de poissons.ENREGISTREMENTN’oubliez pas de conserver votre reçu et d’enregistrerimmédiatement votre propulseur électrique. Une fiched’enregistrement est fournie avec votre moteur; vous pouvezégalement effectuer l’enregistrement sur notre site Web àminnkotamotors.com/register.NUMÉRO DE SÉRIELe numéro de série à 11 caractères Minn Kota est trèsimportant. Cela permet de déterminer le modèle spécifique etl’année de fabrication. Lorsque vous contactez le Service à laclientèle ou que vous enregistrez votre article, vous aurez besoindu numéro de série de votre article. Nous vous suggérons denoter le numéro de série afin qu’il soit disponible à des fins deréférence future.Made by Minn KotaJohnson OutdoorsMarine Electronics, Inc.121 Power DriveMankato, MN 56001 USATrolling MotorsProduced in XXXXPRODUCT DESCRIPTIONMODEL XXXXXXXXXV DCXX ASER NO YYDDDC00000EXEMPLEAVIS : Le numéro de série de votre Riptide Terrova setrouve à l’intérieur du support de montage, sous le pointd’appui du moteur.INFORMATION SUR LE M
You may obtain service by: calling Minn Kota at (800) 227-6433; returning your motor to the Minn Kota Factory Service Center; sending or taking your motor to any Minn Kota authorized service center. A list of authorized service centers is available on our website, at minnkotamotors.com.
Ukulele riptide chords pdf download full version full Tortoise and the hare!Song StructureFor the most part the song remains pretty much the same throughout simply repeating Am, G and C. Let's take a look at how to play it Riptide ChordsThe good news is that there are just four chords in Riptide and you'll probably already be familiar .
RIPTIDE ULTERRA QUICK START UP GUIDE POWER ON The Riptide Ulterra trolling motor must be powered "on" manually. The remote will not turn the motor on. The power button is located on the base of the mo-tor. Pressing the power button will turn on Riptide Ulterra. The red STATUS light and the green SYSTEM READY light will both
Riptide is able to move and complete the various tasks of the RoboSub competition through the use of several actuators mounted to the chassis of the vehicle. 1) Thrusters Ten T200 Blue Robotics thrusters are utilized on Riptide and give it the ability to move with six degrees of freedom. The thrusters are fixed to the water-jet chassis, four .
Easy riptide piano sheet music. Riptide guitar sheet music for beginners. For example, the thumb finger may go on middle C. One to practice :).Bb C C# D# F-Bb G# F F I was scared of dentists and the dark.Bb C C# D# F-Bb G# I was scared of pretty girlsD# F-D# F-D#-F-G# And starting conversationsD#-F Oh F F F F F-D# F All my friends are turning greenF D#
Ensure the NUU Riptide is fully charged before using as a USB speaker. Your computer's USB port may not be able to supply enough power to charge and play music at the same time. h & i Aux-In & Aux-Out The NUU Riptide can connect to any device with a 3.5mm headphone 13 Riptide_UserManual_Final.indd 14 7/17/2014 3:07:13 PM
Riptide Vance Joy Intro: [Am] DDUuD [G] DDUuD [C] DDUuD [C] D [Am] DDUuD [G] DDUuD [C] DDUuD [C] D {soloists} [Am] I was scared of [G] dentists and the [C] dark, [Am] I was scared of [G] pretty girls and [C] starting conversations, Oh [Am] all my friends are turning [C] green, You're the ma-[Am]-gicians as-[G]-sistant in their [C] dreams{all} Ah-[Am] ooh, [G] ooh oo-oo-[C]-ooh
RIpTIdE 09 sTANdARds & opTIoNs ApplIANCEs ANd ACCEssoRIEs opTIoNs Double -Door Refrigerator 3-Burner High Output Gas Range with Oven 32" Color LCD TV in Main Living Area (330, 341) 26" Color LCD TV in Cockpit Overhead Cabinet (N/A 330, 341)
APM Group Limited 2014. AgilePgM is a trade mark of the DSDM Consortium. Dynamic Systems Development Method Limited 2014. The APMG International Swirl .
